We capped our max_bio_size respectively max_hw_sectors with
min_t(int, lower level limit, our limit);
unfortunately, some drivers, e.g. the kvm virtio block driver, initialize their
limits to "-1U", and that is of course a smaller "int" value than our limit.
Impact: we started to request 16 MB resync requests,
which lead to protocol error and a reconnect loop.
Fix all relevant constants and parameters to be unsigned int.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If you do back to back wait-sync/invalidate on a Primary in a tight loop,
during application IO load, you could trigger a race:
kernel: block drbd6: FIXME going to queue 'set_n_write from StartingSync'
but 'write from resync_finished' still pending?
Fix this by changing the order of the drbd_queue_work() and
the wake_up() in dec_ap_pending(), and adding the additional
drbd_flush_workqueue() before requesting the full sync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Fix asserts like
block drbd0: in got_BlockAck:4634: rs_pending_cnt = -35 < 0 !
We reset the resync lru cache and related information (rs_pending_cnt),
once we successfully finished a resync or online verify, or if the
replication connection is lost.
We also need to reset it if a resync or online verify is aborted
because a lower level disk failed.
In that case the replication link is still established,
and we may still have packets queued in the network buffers
which want to touch rs_pending_cnt.
We do not have any synchronization mechanism to know for sure when all
such pending resync related packets have been drained.
To avoid this counter to go negative (and violate the ASSERT that it
will always be >= 0), just do not reset it when we lose a disk.
It is good enough to make sure it is re-initialized before the next
resync can start: reset it when we re-attach a disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the drbd worker thread is synchronously waiting for some userland
callback, we don't want some casual pageout to block on us.
Have drbd_congested() report congestion in that case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Aborting local requests (not waiting for completion from the lower level
disk) is dangerous: if the master bio has been completed to upper
layers, data pages may be re-used for other things already.
If local IO is still pending and later completes,
this may cause crashes or corrupt unrelated data.
Only abort local IO if explicitly requested.
Intended use case is a lower level device that turned into a tarpit,
not completing io requests, not even doing error completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Pull block driver updates from Jens Axboe:
"Here are the driver related changes for 3.5. It contains:
- The floppy changes from Jiri. Jiri is now also marked as the
maintainer of floppy.c, I shall be publically branding his forehead
with red hot iron at the next opportune moment.
- A batch of drbd updates and fixes from the linbit crew, as well as
fixes from others.
- Two small fixes for xen-blkfront courtesy of Jan."
* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
floppy: take over maintainership
floppy: remove floppy-specific O_EXCL handling
floppy: convert to delayed work and single-thread wq
xen-blkfront: module exit handling adjustments
xen-blkfront: properly name all devices
drbd: grammar fix in log message
drbd: check MODULE for THIS_MODULE
drbd: Restore the request restart logic
drbd: introduce a bio_set to allocate housekeeping bios from
drbd: remove unused define
drbd: bm_page_async_io: properly initialize page->private
drbd: use the newly introduced page pool for bitmap IO
drbd: add page pool to be used for meta data IO
drbd: allow bitmap to change during writeout from resync_finished
drbd: fix race between drbdadm invalidate/verify and finishing resync
drbd: fix resend/resubmit of frozen IO
drbd: Ensure that data_size is not 0 before using data_size-1 as index
drbd: Delay/reject other state changes while establishing a connection
drbd: move put_ldev from __req_mod() to the endio callback
drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
...
In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.
In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).
Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.
In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.
Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.
The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).
To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a resync or online verify is finished or aborted,
drbd does a bulk write-out of changed bitmap pages.
If *in that very moment* a new verify or resync is triggered,
this can race:
ASSERT( !test_bit(BITMAP_IO, &mdev->flags) ) in drbd_main.c
FIXME going to queue 'set_n_write from StartingSync' but 'write from resync_finished' still pending?
and similar.
This can be observed with e.g. tight invalidate loops in test scripts,
and probably has no real-life implication.
Still, that race can be solved by first quiescen the device,
before starting a new resync or verify.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Changes to the role and disk state should be delayed or rejected
while we establish a connection.
This is necessary, since the peer will base its resync decision
on the UUIDs and the state we sent in the drbd_connect() function.
The most prominent example for this race is becoming primary after
sending state and UUIDs and before the state changes to C_WF_CONNECTION.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD state changes schedule after_state_ch() actions to a worker thread,
which decides on the old and new states of that change, whether to send
an informational state update packet (P_STATE) to the peer.
If it decides to drbd_send_state(), it would however always send the
_curent_ state, which, if a second state change happens before the
after_state_ch() of the first ran, may "fast-forward" the peer's view
about this node. In most cases that is harmless, but sometimes this can
confuse DRBD, for example into not actually starting a necessary resync
if you do a very tight detach/attach loop on a Connected Secondary.
Fix this by always sending the "new" state of the respective state
transition which scheduled this after_state_ch() work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When detaching, even cleanly detaching due to administrator request,
we always go through D_FAILED before we become D_DISKLESS.
Don't let that state change race with an in-flight meta data IO,
or that one might think it actually experienced an IO error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Regression introduced with 8.3.11 commit:
drbd: Take a more conservative approach when deciding max_bio_size
Never ever tell an older drbd, that we support more than 32KiB
in a single data request (packet).
Never believe an older drbd, that is supports more than 32KiB
in a single data request (packet)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It is not "to small", but "too small".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The buffer 'sc.cpu_mask' is a kernel buffer. If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Found these with the help of ispell -l.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.
This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().
This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.
Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.
manually picked commit 564040f from the drbd 8.4 branch.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The old (optimistic) implementation could shrink the bio size
on an primary device.
Shrinking the bio size on a primary device is bad. Since there
we might get BIOs with the old (bigger) size shortly after
we published the new size.
The new implementation is more conservative, and eventually
increases the max_bio_size on a primary device (which is valid).
It does so, when it knows the local limit AND the remote limit.
We cache the last seen max_bio_size of the peer in the meta
data, and rely on that, to make the operation of single
nodes more efficient.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
cciss: fix lost command issue
drbd: need include for bitops functions declarations
Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation"
cciss: fix missed command status value CMD_UNABORTABLE
cciss: remove unnecessary casts
cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
cciss: Inform controller we are using 32-bit tags.
cciss: hoist tag masking out of loop
cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
cciss: export resettable host attribute
drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
drbd: Fixed handling of read errors on a 'VerifyS' node
drbd: Fixed handling of read errors on a 'VerifyT' node
drbd: Implemented real timeout checking for request processing time
drbd: Remove unused function atodb_endio()
drbd: improve log message if received sector offset exceeds local capacity
drbd: kill dead code
drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
drbd: Removed left over, now wrong comments
drbd: serialize admin requests for new verify run with pending bitmap io
...
This is an addendum to
drbd: serialize admin requests for new resync with pending bitmap io
It avoids a race that could trigger "FIXME" assert log messages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that we do no longer in-place endian-swap the bitmap, we allow
selected bitmap operations (testing bits, sometimes even settting bits)
during some bulk operations.
This caused us to hit a lot of FIXME asserts similar to
FIXME asender in drbd_bm_count_bits,
bitmap locked for 'write from resync_finished' by worker
Which now is nonsense: looking at the bitmap is perfectly legal
as long as it is not being resized.
This cosmetic patch defines some flags to describe expectations in finer
detail, so the asserts in e.g. bm_change_bits_to() can be skipped if
appropriate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
All decisions about sync, sync direction, and wether or not to
allow a connect or attach are based on our set of UUIDs to tag a
data generation.
Log changes to the UUIDs whenever they occur,
logging "new current UUID P:Q:R:S" is more useful
than "Creating new current UUID".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the user clears the sync-pause flag, and sync stays in pause
state, give hints to the user, why it still is in pause state.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When we set or clear bits in a bitmap page,
also set a flag in the page->private pointer.
This allows us to skip writes of unchanged pages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
I guess bitmap I/O errors are supposed to cause drbd_determin_dev_size
to return dev_size_error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Warning: comparison between ‘enum drbd_ret_code’ and ‘enum drbd_state_rv’
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As the network connection can be lost at any time, a --force option
for disconnect is just a matter of completeness.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In case we ever should add an other packet type,
we must not reuse 27, as that currently used for
"empty" return code only replies.
Document it as such.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make sure we start with clean buffers to not accidentally send garbage
back to userspace. Note: has not been observed; but just in case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To ease tracking of bios in some hash tables, we want it to
not cross certain boundaries (128k, used to be 32k).
We limit the maximum bio size using queue parameters.
Historically some defines and variables we use there have been named
max_segment_size, which was misguided. Rename them to max_bio_size,
and use [blk_]queue_max_hw_sectors where appropriate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to be limited to 32k requests,
but have increased that limit to 128k now.
This part of the code can only deal with 32k,
it would scramble arbitrary pages for larger requests.
As it is used for debugging only anyways,
it is ok to simply truncate the dumped data here.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Netlink message processing in the kernel is synchronous these days,
capabilities can be checked directly in security_netlink_recv() from
the current process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Reviewed-by: James Morris <jmorris@namei.org>
[chrisw: update to include pohmelfs and uvesafb]
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent blkdev_get() modifications, open_by_devnum() and
open_bdev_exclusive() are simple wrappers around blkdev_get().
Replace them with blkdev_get_by_dev() and blkdev_get_by_path().
blkdev_get_by_dev() is identical to open_by_devnum().
blkdev_get_by_path() is slightly different in that it doesn't
automatically add %FMODE_EXCL to @mode.
All users are converted. Most conversions are mechanical and don't
introduce any behavior difference. There are several exceptions.
* btrfs now sets FMODE_EXCL in btrfs_device->mode, so there's no
reason to OR it explicitly on blkdev_put().
* gfs2, nilfs2 and the generic mount_bdev() now set FMODE_EXCL in
sb->s_mode.
* With the above changes, sb->s_mode now always should contain
FMODE_EXCL. WARN_ON_ONCE() added to kill_block_super() to detect
errors.
The new blkdev_get_*() functions are with proper docbook comments.
While at it, add function description to blkdev_get() too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Joern Engel <joern@lazybastard.org>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: reiserfs-devel@vger.kernel.org
Cc: xfs-masters@oss.sgi.com
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Over time, block layer has accumulated a set of APIs dealing with bdev
open, close, claim and release.
* blkdev_get/put() are the primary open and close functions.
* bd_claim/release() deal with exclusive open.
* open/close_bdev_exclusive() are combination of open and claim and
the other way around, respectively.
* bd_link/unlink_disk_holder() to create and remove holder/slave
symlinks.
* open_by_devnum() wraps bdget() + blkdev_get().
The interface is a bit confusing and the decoupling of open and claim
makes it impossible to properly guarantee exclusive access as
in-kernel open + claim sequence can disturb the existing exclusive
open even before the block layer knows the current open if for another
exclusive access. Reorganize the interface such that,
* blkdev_get() is extended to include exclusive access management.
@holder argument is added and, if is @FMODE_EXCL specified, it will
gain exclusive access atomically w.r.t. other exclusive accesses.
* blkdev_put() is similarly extended. It now takes @mode argument and
if @FMODE_EXCL is set, it releases an exclusive access. Also, when
the last exclusive claim is released, the holder/slave symlinks are
removed automatically.
* bd_claim/release() and close_bdev_exclusive() are no longer
necessary and either made static or removed.
* bd_link_disk_holder() remains the same but bd_unlink_disk_holder()
is no longer necessary and removed.
* open_bdev_exclusive() becomes a simple wrapper around lookup_bdev()
and blkdev_get(). It also has an unexpected extra bdev_read_only()
test which probably should be moved into blkdev_get().
* open_by_devnum() is modified to take @holder argument and pass it to
blkdev_get().
Most of bdev open/close operations are unified into blkdev_get/put()
and most exclusive accesses are tested atomically at the open time (as
it should). This cleans up code and removes some, both valid and
invalid, but unnecessary all the same, corner cases.
open_bdev_exclusive() and open_by_devnum() can use further cleanup -
rename to blkdev_get_by_path() and blkdev_get_by_devt() and drop
special features. Well, let's leave them for another day.
Most conversions are straight-forward. drbd conversion is a bit more
involved as there was some reordering, but the logic should stay the
same.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Brown <neilb@suse.de>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: dm-devel@redhat.com
Cc: drbd-dev@lists.linbit.com
Cc: Leo Chen <leochen@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Joern Engel <joern@logfs.org>
Cc: reiserfs-devel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
