Most of our register defines follow the convention that if there's a
need for the raw register offset, that one has an underscore sa a
prefix. The define (possibly parametrized) without the underscore is
the one people should normally use, since it will take into account
all the parameters and other potential offsets that are needed.
Fix up the few stragglers that don't follow this convention.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-14-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
If we ignore the BXT situation, we can observe that the only variables
affecting gpio_mmio_base is IS_VALLEVIEW and HAS_GMCH_DISPLAY. The BXT
situation we can fit into the same pattern if we change gmbus_pins_bxt[]
to house the GMCH GPIO register offsets (like we do for all other
platfotms). So let's do that.
We could even simplify the VLV situation more by including the
display_mmio_offset in the GPIO register defines, but let's leave it be
for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store the DVO SRCDIM register offset alongside the DVO control register
offset in intel_dvo_device. This gets rid of the switch statement whose
case values are the DVO control register offsets. Such a construct would
cause problems for register type safety.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-12-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Replace the is_sdvob bool and some sdvo_reg checks with enum port. This
makes the SDVO code look more modern, and gets rid of explicit register
offset checks in the code which will hamper register type checking.
v2: Add assert_sdvo_port_valid() (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1446838199-3666-1-git-send-email-ville.syrjala@linux.intel.com
It was created at 'commit aabc95dcf2 (drm/i915: Dont -ETIMEDOUT
on identical new and previous (count, crc).")' becase the counter
wasn't reliable.
Now that we properly wait for the counter to be reset we can rely
a bit more in the counter.
Also that patch stopped to return -ETIMEDOUT so the test case is
unable to skip when it is unreliable and end up in many fails
that should be skip instead.
So, with the counter more reliable we can remove
this hack that just makes things more confusing when test cases
are really expecting the same CRC and let test case skip if that's
not the case.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to VESA DP spec TEST_CRC_COUNT (Bits 3:0) at
TEST_SINK_MISC (00246h) is "Reset to 0 when TEST_SINK bit 0 = 0;
So let's give few vblanks so we are really sure that this counter
is really zeroed on the next sink_crc read.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to VESA DP Spec, setting TEST_SINK_START (bit 0)
of TEST_SINK (00270h) "Stop/Start calculating CRC on the next frame"
So let's wait at least 1 vblank to really say the calculation
stopped or started.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handle DC off as a power well where enabling the power well will prevent
the DMC to enter selected DC states (required around modesets and Aux
A). Disabling the power well will allow DC states again. For now the
highest DC state is DC6 for Skylake and DC5 for Broxton but will be
configurable for Skylake in a later patch.
v2: Check both DC5 and DC6 bits in power well enabled function (Ville)
v3:
- Remove unneeded DC_OFF case in skl_set_power_well() (Imre)
- Add PW2 dependency to DC_OFF (Imre)
v4: Put DC_OFF before PW2 in BXT power well array
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[fixed line over 80 and parenthesis alignment checkpatch warns (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1447687201-24759-1-git-send-email-patrik.jakobsson@linux.intel.com
PG2 enabled is not a requirement for disabling DC5. It's just one
of the reasons why the DMC wouldn't enter DC5. During modeset we don't
care about PG2 from a DC perspective, only the fact that DC5/DC6 is not
allowed.
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-9-git-send-email-patrik.jakobsson@linux.intel.com
All the DDI power domains are already excluded from
SKL_DISPLAY_ALWAYS_ON_POWER_DOMAINS on account of
excluding SKL_DISPLAY_POWERWELL_1_POWER_DOMAINS and
SKL_DISPLAY_POWERWELL_2_POWER_DOMAINS, no need to spell them out again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-6-git-send-email-patrik.jakobsson@linux.intel.com
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-5-git-send-email-patrik.jakobsson@linux.intel.com
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447682467-6237-1-git-send-email-patrik.jakobsson@linux.intel.com
Replaces "drm/i915: Force loading of csr program at boot" in the old
series.
Previously we called blindly into intel_csr_load_program() and depended
on a check of whether the CSR program memory was cleared or not.
This check is not reliable and no longer needed since we fixed the
call-sites of intel_csr_load_program().
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447084107-8521-2-git-send-email-patrik.jakobsson@linux.intel.com
When this option is 0 (so the power well support is disabled) we are
supposed to enable all power wells once and don't disable them unless we
system suspend the device. Currently if the option is 0, we can call the
power well enable handlers multiple times, whenever their refcount
changes from 0->1. This may not be a problem for the HW, but it's not
logical and may trigger some warnings in the power well code which
doesn't expect this. So simply keep around a reference while we are
not system suspended to solve this. For simplicity mark the module
option read only, so we don't need to deal with re-enabling the feature
during runtime. If someone really needs that it could be added later in
a more proper way.
v2:
- fix typo in comment in intel_power_domains_suspend() (Patrik)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447775063-24438-1-git-send-email-imre.deak@intel.com
We don't need to reinit DDI and IRQs during PW1 enabling any more, since
we don't toggle PW1 on-demand any more. We enable PW1 only as part of
the display core init sequence and after this we initialize both DDI and
IRQs later in the init sequence. So remove these init steps from the
power well code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-11-git-send-email-imre.deak@intel.com
Suppressing LCPLL disabling was added to avoid interfering with the DMC
firmware. It is not needed any more since we uninit CDCLK now with the
DMC deactivated (DC states disabled). We also must disable it during system
suspend as part of the Bspec "Display uninit sequence".
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-10-git-send-email-imre.deak@intel.com
We need to disable the DC states during display core init to sanitize
the HW state we inherit from the BIOS. We need to disable it during
display core uninit too, since the power well framework will leave it
enabled (since we get to the display core uninit step with all power
domains disabled already).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-9-git-send-email-imre.deak@intel.com
With the DMC firmware installed we don't need to handle HW resources
that are handled automatically by the firmware. Besides being redundant
this can also interfere with the firmware, possibly getting it into a
broken/blocked state. The on-demand handling of PW1 was already half-way
removed, MISC IO was still handled in this way. After the last patch we
init/uninit these HW resources manually as part of the display core
init/uninit sequence, so we can now remove the on-demand handling for
these completely.
We still keep around the power wells (with no domains attached to them)
since the manual toggling during display core init/uninit happens via
the current API.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[s/beeing/being/ in commit message (imre)]
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-7-git-send-email-imre.deak@intel.com
We need to initialize the display core part early, before initializing
the rest of the display power state. This is also described in the bspec
termed "Display initialization sequence". Atm we run this sequence
during driver loading after power domain HW state initialization which
is too late and during runtime suspend/resume which is unneeded and can
interere with DMC functionality which handles HW resources toggled
by this init/uninit sequence automatically. The init sequence must be
run as the first step of HW power state initialization and during
system resume. The uninit sequence must be run during system suspend.
To address the above move the init sequence to the initial HW power
state setup and the uninit sequence to a new power domains suspend
function called during system suspend.
As part of the init sequence we also have to reprogram the DMC firmware
as it's lost across a system suspend/resume cycle.
After this change CD clock initialization during driver loading will
happen only later after other dependent HW/SW parts are initialized,
while during system resume it will get initialized as the last step of
the init sequence. This distinction can be removed by some refactoring
of platform independent parts. I left this refactoring out from this
series since I didn't want to change non-SKL parts. This is a TODO for
later.
v2:
- fix error path in i915_drm_suspend_late()
- don't try to re-program the DMC firmware if it failed to load
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447774433-20834-1-git-send-email-imre.deak@intel.com
Before this patch, we used the intel_display_power_{get,put} functions
to make sure the PW1 and Misc I/O power wells were enabled all the
time while LCPLL was enabled. We called a get() at
intel_ddi_pll_init() when we discovered that LCPLL was enabled, then
we would call put/get at skl_{un,}init_cdclk().
The problem is that skl_uninit_cdclk() is indirectly called by
intel_runtime_suspend(). So it will only release its power well
_after_ we already decided to runtime suspend. But since we only
decide to runtime suspend after all power wells and refcounts are
released, that basically means we will never decide to runtime
suspend.
So what this patch does to fix that problem is move the PW1 + Misc I/O
power well handling out of the runtime PM mechanism: instead of
calling intel_display_power_{get_put} - functions that touch the
refcount -, we'll call the low level intel_power_well_{en,dis}able,
which don't change the refcount. This way, it is now possible for the
refcount to actually reach zero, and we'll now start runtime
suspending/resuming.
v2 (from Paulo):
- Write a commit message since the original patch left it empty.
- Rebase after the intel_power_well_{en,dis}able rename.
- Use lookup_power_well() instead of hardcoded indexes.
Testcase: igt/pm_rpm/rte (and every other rpm test)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92211
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92605
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-4-git-send-email-imre.deak@intel.com
The current lookup code wouldn't find a power well if it's not in any
power domain. There wasn't any power wells before but an upcoming patch
will detach the power domains from power well#1 and the MISC IO power
wells, so fix things up accordingly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-3-git-send-email-imre.deak@intel.com
lookup_power_well() expects uniq power well IDs, but atm we have
uninitialized IDs which would clash with those power wells with a 0
ID. This wasn't a problem so far since nothing looked up such a power
well, but an upcoming patch will (Misc IO for SKL), so fix this up on
platforms where this matters.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446657859-9598-2-git-send-email-imre.deak@intel.com
After fixing the same issue in the set_caching IOCTL and Chris' request
to check out the possibilities for an improved RPM ref handling I
noticed that we have the same issue in the set_tiling IOCTL. Fix this
up.I didn't see any bug reports about this one, but the GTT unbind
operation on this path accesses the HW, which needs the ref.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447092986-11165-1-git-send-email-imre.deak@intel.com
When accessing through the GTT from one CPU whilst concurrently updating
the GGTT PTEs in another thread, the hardware likes to return random
data. As we have strong serialisation prevent us from modifying the PTE
of an active GTT mmapping, we have to conclude that it whilst modifying
other PTE's that error occurs. (I have not looked for any pattern such
as modifying PTE within the same page or cacheline as active PTE -
though checking whether revoking neighbouring objects should be enough
to test that theory.) The corruption also seems restricted to Braswell
and disappears with maxcpus=0. This patch stops all access through the
GTT by other CPUs when we update any PTE by stopping the machine around
the GGTT update.
Note that splitting up the 64 bit write into two 32 bit writes was
tried and found to fail too.
Testcase: igt/gem_concurrent_blit
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89079
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about 2x 32bits failing too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Compliance test 4.3.1.11 requires source to perform link training
always if the automated test requests for it. This patch
enforces this requirement.
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Automated test data that is updated when a test is requested is not cleared
till next automated test request is recevied which can cause various
problems. This patch fixes this by clearing this during the next
short pulse and on hot unplug.
For example, when TEST_LINK_TRAINING is requested it is updated
to appropriate variable inside intel_dp_handle_test_request
but is also cleared only inside the same function. if the next
short pulse does not have the AUTOMATED_TEST_REQUEST bits set
the variable will not be cleared resulting in carrying incorrect
test status in local variables.
v2: Added comments and moved nack and defer variables before set_edid
(Sonika)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If ddb allocation for planes in current CRTC is changed, that doesn't
lead to ddb allocation change for other CRTCs, because our DDB allocation
is not dynamic according to plane parameters, ddb is allocated according
to number of CRTC enabled, & divided equally among CTRC's.
In current condition check during Watermark calculation, if number of
plane/ddb allocation changes for current CRTC, Watermark for other pipes
are recalculated. But there is no change in DDB allocation of other pipe
so watermark is also not changed, This leads to warning messages.
WARN_ON(!wm_changed)
This patch corrects this and check if DDB allocation for pipes is changed,
then only recalculate watermarks.
v2 (by Matt): Rebased to latest -nightly and fixed a typo
Signed-off-by: Kumar, Mahesh <mahesh1.kumar@intel.com>
Reviewed-by(v1): Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the EDP_PSR_BASE() thing, and just stick the PSR register offset
under dev_priv, like we for DSI and GPIO for example.
TODO: could probably move a bunch of this kind of stuff into the device
info instead...
v2: Drop the spurious whitespace change (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-7-git-send-email-ville.syrjala@linux.intel.com
Rather than computing on demand, store also the aux data reg
offsets under intel_dp.
v2: Duplicate some code to make things less magic (Jani)
v3: Use PORT_B registers for invalid ports in g4x_aux_data_reg()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-6-git-send-email-ville.syrjala@linux.intel.com
Currently we determine the location of the AUX registers in a confusing
way. First we assume the PCH registers are used always, but then we
override it for everything but HSW/BDW to use DP+0x10. Very confusing.
Let's just make it straightforward and simply add a few functions to
pick the right AUX_CTL based on the DP port.
To deal with VLV/CHV we'll include the display_mmio_offset into the
AUX register defines.
v2: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-5-git-send-email-ville.syrjala@linux.intel.com
v2: Keep some MISSING_CASE() stuff (Jani)
s/-1/-PIPE_B/ in the register macro
Fix typo in patch subject
v3: Use PORT_B registers for invalid ports in g4x_aux_ctl_reg() (Jani)
v4: Reorder patches (Chris)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-4-git-send-email-ville.syrjala@linux.intel.com
Use kasprintf() to generate the "DPDDC-<port>" name for the aux helper.
To deal with errors properly make intel_dp_aux_init() return something,
and adjust the caller to match. It seems we were also missing a
intel_dp_mst_encoder_cleanup() call on edp (non-port A) init failures,
so add that too.
The whole error/cleanup ordering doesn't feel entirely sane to me, but
I'll leave that part alone for now.
v2: Use kasprintf() instead of a table, reorder patches (Chis)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447266856-30249-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
While comparing the B-Spec with the code I noticed that several
values in these tables have been updated in the spec, so I
changed the code to match..
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446852654-883-1-git-send-email-jim.bride@linux.intel.com
The i_boost level in the DDI translation tables are stored per level.
However, skl_ddi_set_iboos() would choose an entry of that table based
on the port argument.
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447247754-802-1-git-send-email-ander.conselvan.de.oliveira@intel.com
As during disabling dc6 no need to check for csr firmware
loading status, so removed the assert call (Requested by Damien).
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-14-git-send-email-imre.deak@intel.com
Currently during system s/r we enable/disable DC6, so before we do so
make sure that the firmware loading is complete.
Note that whether we need to enable DC6 for S3/S4 is still open. At
least the firmware program is lost during S3 and we need to reprogram it
after resuming. Until this is clarified we keep the current behavior and
enable/disable DC6.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-13-git-send-email-imre.deak@intel.com
During driver unload to ensure we dont have any pending task,
flush_work added to complete firmware loading task.
v1: Initial version.
v2: As per review comments from Daniel,
Removed flush_work from skl_set_power_well. As we have taken
power well refernece and rpm count during firmware loading
by using display_power_domain_get/put - this will always
ensure rpm will be blocked if firmware is not loaded.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-12-git-send-email-imre.deak@intel.com
Two benefits:
- We can use FW_LOADER_USERSPACE_FALLBACK.
- We can use flush_work to synchronize with the oustanding worker,
which is a notch more obvious what it does than having a special
completion.
The next patch will properly synchronize against the async loader in
the resume and unload code.
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com> # SKL
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446069547-24760-11-git-send-email-imre.deak@intel.com
