by setting IOC always, we can recycle TRBs a
lot sooner at the expense of some increased
CPU load.
The extra load seems to be quite minimal on
OMAP5 devices (instead of 1 IRQ for one MSC
transfer, we get
CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS).
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes problem with unnecessary usb_ep_set_maxpacket_limit() usage.
It should not be used in at91udc_probe() function, where maxpacket values are
set for field "maxpacket" of struct at91_ep, which is representation of
endpoint in driver internals. Function usb_ep_set_maxpacket_limit() is called
in udc_reinit() function, where struct usb_ep instances are initialised with
values set previously in struct at91_ep instances. So it's very important to
initialise it properly.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `txstate':
musb_gadget.c:(.text+0x35955a): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x35957e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x359672): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x3596ba): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x3596e0): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `rxstate':
musb_gadget.c:(.text+0x3599d0): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x3599f6): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `musb_gadget_queue':
musb_gadget.c:(.text+0x35a8c0): undefined reference to `dma_map_single'
musb_gadget.c:(.text+0x35a8d0): undefined reference to `dma_mapping_error'
musb_gadget.c:(.text+0x35a906): undefined reference to `dma_sync_single_for_cpu'
musb_gadget.c:(.text+0x35a9a0): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x35a9c8): undefined reference to `dma_sync_single_for_cpu'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The probe() method has the 'dev' local variable declared and used but strangely
not in all cases where it should be...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of relying on the otg pointer, which
can be NULL in certain cases, we can use the
gadget and host pointers we already hold inside
struct musb.
Cc: <stable@vger.kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some older XHCIs streams are not supported and the UAS driver
will fail at probe time. For those devices storage should try
to bind to UAS devices.
This patch adds a flag for stream support to HCDs and evaluates
it.
[Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root
hub would get marked as being able to support streams.]
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
If the host controller stops responding to commands, we need to kill all
the URBs that were queued to all endpoints. The current code would only
kill URBs that had been queued to the endpoint rings. ep->ring is set
to NULL if streams has been enabled for the endpoint, which means URBs
submitted with a non-zero stream_id would never get killed. Fix this.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
In preparation for fixing this function for streams endpoints, refactor
code in the command watchdog timeout function into two new functions.
One kills all URBs on a ring (either stream or endpoint), the other
kills all URBs associated with an endpoint. Fix a split string while
we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Although an interesting concept, I don't think that this is a good idea:
-This will result in lots of "virtual" scsi controllers confusing users
-If we get a scsi-bus-reset we will now need to do a usb-device-reset of all
uas devices on the same usb bus, which is something to avoid if possible
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
At the kernel-summit Sarah Sharp asked me if I was willing to become the
uas maintainer. I said yes, and here is a patch to make this official.
Also remove Matthew Wilcox and Sarah Sharp as maintainers at their request.
I've also added myself to the module's author tag, so that if people look there
rather then in maintainers they will know they should bug me about uas too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci streams support is fixed, unblock usb attached scsi.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Copy the sg alignment trick from the usb-storage driver, without this I'm
seeing intermittent errors when using uas devices with an ehci controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The scsi error handling path re-uses previously queued up (and errored-out)
cmds. If such a re-used cmd had a data-phase then cmdinfo will have
data_in_urb / data_out_urb still set to the free-ed urbs from the errored-out
cmd, and they will get free-ed a second time when the error handling cmd
completes, corrupting the kernel heap.
Clearing cmdinfo on command queue-ing fixes this, and seems like a good idea
in general.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The scsi-host structure is refcounted, scsi_remove_host tears down the
scsi-host but does not decrement the refcount, so we need to call
scsi_put_host on disconnect to get the underlying memory to be freed.
After calling scsi_remove_host, the scsi-core may still hold a reference to
the scsi-host, iow we may still get called after uas_disconnect, but we
do our own life cycle management of uas_devinfo, freeing it on disconnect,
and thus may end up using devinfo after it has been freed. Switch to letting
scsi_host_alloc allocate and manage the memory for us.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cmds are either on the inflight list or on the dead list, never both, so
we only need one list head.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Before this commit the uas driver would keep track of scsi commands which still
need to have some urbs submitted to the device, and complete this with an
ABORT result code on bus-reset or disconnect, but in flight scsi commands
which have all their urbs submitted, and thus are not part of the work list,
would never get their done callback called.
The problem is killed sense urbs don't have any tag info, so it is impossible
to tell which scsi cmd they belong to, so merely making sure all the urbs
have completed one way or the other is not enough.
This commit fixes this by changing the work list to an inflight list, which
keeps tracks of all inflight scsi cmnds, using the IS_IN_WORK_LIST flag to
determine if actual work needs to be done in uas_do_work(), and by moving
marking all inflight scsi commands as aborted and moving them to the dead list
on bus-reset or disconnect.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
uas_alloc_data_urb always gets called with a stream_id value of 0 when not
using streams. Removing the check makes it consistent with uas_alloc_sense_urb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
For USB-2 connections the stream-id must always be 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some BIOS-es will hang on reboot when an uas device is attached and left in
uas mode on reboot.
This commit adds a shutdown handler which on reboot puts the device back into
usb-storage mode, fixing the hang on reboot on these systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We can sleep in our own workqueue (which is the whole reason for having
it), and scsi error handlers are also always called from a context which
may sleep.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since we use a fixed tag / stream for tasks we cannot allow more then one
to run at the same time. This could happen before this time if a task timed
out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The fixed endpoint config code was only necessary to deal with an early
uas prototype which has never been released, so lets drop it and enforce
proper uas endpoint descriptors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The loop uses up to 3 bytes of the endpoint extra data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding better descriptor validation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Falling back from uas to usb-storage requires coordination between uas and
usb-storage, so use usb-storage's quirks module parameter, rather then
requiring the user to pass a param to 2 different modules.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
uas devices have 2 alternative settings on their usb-storage interface,
one for usb-storage and one for uas. Using the uas driver is preferred, so if
the uas driver is enabled, and the device has an uas alt setting, don't bind.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Once we start supporting uas hardware, and as more and more uas devices
become available, we will likely start seeing broken devices. This patch
prepares for the inevitable need for blacklisting those devices from
using the uas driver (they will use usb-storage instead).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
On disconnect USB3 protocol ports transit from U0 to SS.Inactive to Rx.Detect,
on a recoverable error, the port stays in SS.Inactive and we recover from it by
doing a warm-reset (through usb_device_reset if we have a udev for the port).
If this really is a disconnect we may end up trying the warm-reset anyways,
since khubd may run before the SS.Inactive to Rx.Detect transition, or it
may get skipped if the transition to Rx.Detect happens before khubd gets run.
With a loose connector, or in the case which actually led me to debugging this
bad ACPI firmware toggling Vbus off and on in quick succession, the port
may transition from Rx.Detect to U0 again before khubd gets run. In this case
the device state is unknown really, but khubd happily goes into the resuscitate
an existing device path, and the device driver never gets notified about the
device state being messed up.
If the above scenario happens with a streams using device, as soon as an urb
is submitted to an endpoint with streams, the following appears in dmesg:
ERROR Transfer event for disabled endpoint or incorrect stream ring
@0000000036807420 00000000 00000000 04000000 04078000
Notice how the TRB address is all zeros. I've seen this both on Intel
Pantherpoint and Nec xhci hosts.
Luckily we can detect the U0 to SS.Inactive to Rx.Detect to U0 all having
happened before khubd runs case since the C_LINK_STATE bit gets set in the
portchange bits on the U0 -> SS.Inactive change. This bit will also be set on
suspend / resume, but then it gets cleared by port_hub_init before khubd runs.
So if the C_LINK_STATE bit is set and a warm-reset is not needed, iow the port
is not still in SS.Inactive, and the port still has a connection, then the
device needs to be reset to put it back in a known state.
I've verified that doing the device reset also fixes the transfer event with
all zeros address issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If streams are still allocated on device-reset or set-interface then the hcd
code implictly frees the streams. Clear host_endpoint->streams in this case
so that if a driver later tries to re-allocate them it won't run afoul of the
device already having streams check in usb_alloc_streams().
Note normally streams still being allocated at reset / set-intf would be a
driver bug, but this can happen without it being a driver bug on reset-resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If we align segment dma pool memory to 64 bytes, then a segment can be located
at 0x10000040 - 0x1000043f, and a segment from another ring at 0x10000440 -
0x1000083f. The last trb in the first segment at 0x10000430 will then translate
to the same radix tree key as the first trb of the second segment, while they
are in different rings!
This patches fixes this by changing the alignment of the dma pool to be 1KB
rather then 64 bytes. An alternative fix would be to reduce the shift used
to calculate the radix tree keys, but that would (slighlty) grow the radix
trees so I believe this is the better fix.
Note this patch is mostly theoretical since in practice I've not seen
the dma_pool actually return not 1KB aligned memory.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cmd_ring_reserved_trbs gets decremented by xhci_free_stream_info(), so set it
to 0 after freeing all rings, otherwise it wraps around to a very large value
when rings with streams are free-ed.
Before this patch the wrap-around could be triggered when xhci_resume
calls xhci_mem_cleanup if the controller resume fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for teaching usb-storage to not bind to
uas devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for teaching usb-storage to not bind to
uas devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If we get ie 16 streams we can use stream-id 1-16, not 1-15.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Handle usb-device resets not triggered from uas_eh_bus_reset_handler(), when
this happens, disable cmd queuing during the reset, and wait for existing
requests to finish in pre_reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Fix the uas_eh_bus_reset_handler not properly taking the usbdev lock
before calling usb_device_reset, the usb-core expects this lock to be
taken when usb_device_reset is called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
I thought it would be a good idea to also test uas with usb-2, and it turns out
it was, as it did not work. The problem is that the uas driver was passing the
bEndpointAddress' direction bit to usb_rcvbulkpipe, the xhci code seems to not
care about this, but with the ehci code this causes usb_submit_urb failure.
With this fixed the uas code works nicely with an uas device plugged into
an ehci port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The cmd endpoint never has streams, so the stream_id parameter is unused.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
All callers of unlink_data_urbs drop devinfo->lock before calling it, and
then immediately take it again after the call. And the first thing
unlink_data_urbs does is take the lock again, and the last thing it does
is drop it. This commit removes all the unnecessary lock dropping and taking.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
- Rename labels to properly reflect this
- Don't skip free-ing the streams when scsi_init_shared_tag_map fails
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Otherwise they may complete before they get anchored and thus never get
unanchored (as the unanchoring is done by the usb core on completion).
This commit also remove the usb_get_urb / usb_put_urb around cmd submission +
anchoring, since if done in the proper order this is not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch adds a new list where all requests which are canceled are
added to, so we don't loose them. Then, after killing all inflight
urbs on bus reset (and disconnect) we'll walk over the list and clean
them up.
Without this we can end up with aborted requests lingering around in
case of status pipe transfer errors.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Simplifies locking, we'll protect the list with the device spin lock.
Also plugs races which can happen when two devices operate on the
global list.
While being at it rename the list head from "list" to "work", preparing
for the addition of a second list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This allows userspace to use bulk-streams, just like in kernel drivers, see
Documentation/usb/bulk-streams.txt for details on the in kernel API. This
is exported pretty much one on one to userspace.
To use streams an app must first make a USBDEVFS_ALLOC_STREAMS ioctl,
on success this will return the number of streams available (which may be
less then requested). If there are n streams the app can then submit
usbdevfs_urb-s with their stream_id member set to 1-n to use a specific
stream. IE if USBDEVFS_ALLOC_STREAMS returns 4 then stream_id 1-4 can be
used.
When the app is done using streams it should call USBDEVFS_FREE_STREAMS
Note applications are advised to use libusb rather then using the
usbdevfs api directly. The latest version of libusb has support for streams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch makes it possible to specify a bulk stream id when submitting
an urb using the async usbfs API. It overloads the number_of_packets
usbdevfs_urb field for this. This is not pretty, but given other
constraints it is the best we can do. The reasoning leading to this goes
as follows:
1) We want to support bulk streams in the usbfs API
2) We do not want to extend the usbdevfs_urb struct with a new member, as
that would mean defining new ioctl numbers for all async API ioctls +
adding compat versions for the old ones (times 2 for 32 bit support)
3) 1 + 2 means we need to re-use an existing field
4) number_of_packets is only used for isoc urbs, and streams are bulk only
so it is the best (and only) candidate for re-using
Note that:
1) This patch only uses number_of_packets as stream_id if the app has
actually allocated streams on the ep, so that old apps which may have
garbage in there (as it was unused until now in the bulk case), will not
break
2) This patch does not add support for allocating / freeing bulk-streams, that
is done in a follow up patch
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding support for bulk streams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The usb_set_interface documentation says:
* Also, drivers must not change altsettings while urbs are scheduled for
* endpoints in that interface; all such urbs must first be completed
* (perhaps forced by unlinking).
For in kernel drivers we trust the drivers to get this right, but we
cannot trust userspace to get this right, so enforce it by killing any
urbs still pending on the interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Documentation/usb/bulk-streams.txt says:
All stream IDs will be deallocated when the driver releases the interface, to
ensure that drivers that don't support streams will be able to use the endpoint
This commit actually implements this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding support for bulk streams to usbfs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
So that it can be used in other places too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If we're expanding a stream ring, we want to make sure we can add those
ring segments to the radix tree that maps segments to ring pointers.
Try the radix tree insert after the new ring segments have been allocated
(the last segment in the new ring chunk will point to the first newly
allocated segment), but before the new ring segments are linked into the
old ring.
If insert fails on any one segment, remove each segment from the radix
tree, deallocate the new segments, and return. Otherwise, link the new
segments into the tree.
HdG: Add a check to only update stream mappings in xhci_ring_expansion when
the ring is a stream ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The ss_ep_comp bmAttributes filed can contain more info then just the
streams, use usb_ss_max_streams to properly get max streams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This fixes TR dequeue validation failing on Intel XHCI controllers with the
following warning:
Mismatch between completed Set TR Deq Ptr command & xHCI internal state.
Interestingly enough reading the deq ptr from the ep ctx after a
TR Deq Ptr command does work on a Nec XHCI controller, it seems the Nec
writes the ptr to both the ep and stream contexts when streams are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Nec XHCI controllers don't seem to care, but without this Intel XHCI
controllers reject Set TR dequeue commands with a COMP_TRB_ERR, leading
to the following warning:
WARN Set TR Deq Ptr cmd invalid because of stream ID configuration
And very shortly after this the system completely freezes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Before this a device needing ie 32 stream ctxs would end up with an entry from
the small_streams_pool which has 256 bytes entries, where as 32 stream ctxs
need 512 bytes. Things actually keep running for a surprisingly long time
before crashing because of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
And warn about this, as that would be a driver bug.
Like wise drivers should ensure that streams are properly free-ed before a
device is reset. So lets warn about that too. This already causes warnings
in the form of:
[ 96.982398] xhci_hcd 0000:01:00.0: WARN Can't disable streams for endpoint 0x81
, streams are already disabled!
[ 96.982400] xhci_hcd 0000:01:00.0: WARN xhci_free_streams() called with non-streams endpoint
But it is better to also warn about the actual cause of this later warnings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci maintains a radix tree for each stream endpoint because it must
be able to map a trb address to the stream ring. Each ring segment
must be added to the ring for this to work. Currently xhci sticks
only the first segment of each stream ring into the radix tree.
Result is that things work initially, but as soon as the first segment
is full xhci can't map the trb address from the completion event to the
stream ring any more -> BOOM. You'll find this message in the logs:
ERROR Transfer event for disabled endpoint or incorrect stream ring
This patch adds a helper function to update the radix tree, and a
function to remove ring segments from the tree. Both functions loop
over the segment list and handles all segments instead of just the
first.
[Note: Sarah changed this patch to add radix_tree_maybe_preload() and
radix_tree_preload_end() calls around the radix tree insert, since we
can now insert entries in interrupt context. There are now two helper
functions to make the code cleaner, and those functions are moved to
make them static.]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This changes debug messages and warnings in xhci-ring.c
to be on a single line so grep can find them. grep must
have precedence over the 80 column limit.
[Sarah fixed two checkpatch.pl issues with split lines
introduced by this commit.]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver currently uses a USB core internal field,
udev->lpm_capable, to indicate the xHCI driver knows how to calculate
the LPM timeout values. If this value is set for the host controller
udev, it means Link PM can be enabled for child devices under that host.
Change the code so the xHCI driver isn't mucking with USB core internal
fields. Instead, indicate the xHCI driver doesn't support Link PM on
this host by clearing the U1 and U2 exit latencies in the roothub
SuperSpeed Extended Capabilities BOS descriptor.
The code to check for the roothub setting U1 and U2 exit latencies to
zero will also disable LPM for external devices that do that same. This
was already effectively done with commit
ae8963adb4 "usb: Don't enable LPM if the
exit latency is zero." Leave that code in place, so that if a device
sets one exit latency value to zero, but the other is set to a valid
value, LPM is only enabled for the U1 or U2 state that had the valid
value. This is the same behavior the code had before.
Also, change messages about missing Link PM information from warning
level to info level. Only print a warning about the first device that
doesn't support LPM, to avoid log spam. Further, cleanup some
unnecessary line breaks to help people to grep for the error messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Since commit 2d22b42db0 "usb: phy: registering Tegra USB PHY as
platform driver" the driver no longer relies on the hard-coded physical
addresses to determine the association between PHY and EHCI port, so
these defines can be dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "pointer targets differ in signedness" and "variable set but not
used" warnings
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user-settable knob, low_latency, has been the source of
several BUG reports which stem from flush_to_ldisc() running
in interrupt context. Since 3.12, which added several sleeping
locks (termios_rwsem and buf->lock) to the input processing path,
the frequency of these BUG reports has increased.
Note that changes in 3.12 did not introduce this regression;
sleeping locks were first added to the input processing path
with the removal of the BKL from N_TTY in commit
a88a69c912,
'n_tty: Fix loss of echoed characters and remove bkl from n_tty'
and later in commit 38db89799b,
'tty: throttling race fix'. Since those changes, executing
flush_to_ldisc() in interrupt_context (ie, low_latency set), is unsafe.
However, since most devices do not validate if the low_latency
setting is appropriate for the context (process or interrupt) in
which they receive data, some reports are due to misconfiguration.
Further, serial dma devices for which dma fails, resort to
interrupt receiving as a backup without resetting low_latency.
Historically, low_latency was used to force wake-up the reading
process rather than wait for the next scheduler tick. The
effect was to trim multiple milliseconds of latency from
when the process would receive new data.
Recent tests [1] have shown that the reading process now receives
data with only 10's of microseconds latency without low_latency set.
Remove the low_latency rx steering from tty_flip_buffer_push();
however, leave the knob as an optional hint to drivers that can
tune their rx fifos and such like. Cleanup stale code comments
regarding low_latency.
[1] https://lkml.org/lkml/2014/2/20/434
"Yay.. thats an annoying historical pain in the butt gone."
-- Alan Cox
Reported-by: Beat Bolli <bbolli@ewanet.ch>
Reported-by: Pavel Roskin <proski@gnu.org>
Acked-by: David Sterba <dsterba@suse.cz>
Cc: Grant Edwards <grant.b.edwards@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Hal Murray <murray+fedora@ip-64-139-1-69.sjc.megapath.net>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Better check the correct bit on big endian systems too. Shuts
up the following sparse __CHECK_ENDIAN__ warning:
.../hub.c:3965:32: warning: restricted __le32 degrades to integer
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error case isn't reported during enumeration.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a debug print in the transfer dequeue case where a
transfer result arrives for a transfer that has already been cleaned up.
It also adds the transfer ID to some debug prints and prints error codes
as signed integers in a couple of others.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the iso_frame_desc.actual_length field instead of length when
reading isoc in data segments from the HWA. This fixes a case where the
isoc in read URB would never complete because it expected the HWA to
send more data than it actually did. When this happened the URB would
be stuck in the driver preventing module unload and clean shutdown.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the endpoint companion descriptor is not the first descriptor in the
extra descriptor buffer of a usb_host_endpoint, the loop in
rpipe_epc_find will get its buffer pointer and remaining size values out
of sync. The buffer ptr 'itr' is advanced by the descriptor's bLength
field but the remaining size value 'itr_size' is decremented by the
bDescriptorType field which is incorrect. This patch fixes the loop to
decrement itr_size by bLength as it should.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a convenience function for the commonly performed task
of marking a transfer segment as done. It combines the 3 steps of
setting the segment status, incrementing the segs_done field of the
transfer and checking if the completed segment results in the transfer
also being done.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch takes a reference to the wa_xfer object in wa_urb_dequeue to
prevent the urb giveback code from completing the xfer and freeing it
while wa_urb_dequeue is executing. It also checks for done at the start
to avoid a double completion scenario. Adding the check for done in
urb_dequeue means that any other place where a submitted transfer
segment is marked as done must complete the transfer if it is done.
__wa_xfer_delayed_run was not checking this case so that check was added
as well.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds error checking to the abort request callback to forcibly
clean up the dequeued transfers if the abort request failed. The
wa_complete_remaining_xfer_segs was modified so that it could be used in
this situation as well. This fixes a stranded URB/PNP hang when the HWA
is unplugged while playing audio to a wireless audio device.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds ref counting to sections of code that operate on struct
wa_xfer objects that were missing it. Specifically, error handling
cases need to be protected from freeing the xfer while it is still in
use elsewhere. This fixes a kernel panic that can occur when pulling
the HWA dongle while data is being transferred to a wireless device.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_irq() and ehci_hrtimer_func() can deadlock on ehci->lock when
threadirqs option is used. To prevent the deadlock use
spin_lock_irqsave() in ehci_irq().
This change can be reverted when hrtimer callbacks become threaded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete ARM's asm/system.h. It's the last holdout and should be got rid of.
This builds for defconfig, lpc32xx_defconfig, exynos_defconfig + XEN, the
previous changed to a Gemini system and an omap3 config with TI_DAVINCI_EMAC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It is an error for a driver to call usb_clear_halt() or
usb_reset_endpoint() while there are URBs queued for the endpoint,
because the end result is not well defined. At the time the endpoint
gets reset, it may or may not be actively running.
As far as I know, no kernel drivers do this. But some userspace
drivers do, and it seems like a good idea to bring this error to their
attention.
This patch adds a warning to the kernel log whenever a program invokes
the USBDEVFS_CLEAR_HALT or USBDEVFS_RESETEP ioctls at an inappropriate
time, and includes the name of the program. This will make it clear
that any subsequent errors are not due to the misbehavior of a kernel
driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead
of accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- delete the warning message at interrupt handler, and adds judgement at
ep_enable, if non-ep0 requests ctrl transfer, it will indicate an error.
- delete hw_test_and_clear_setup_status which is a broken code
- Tested with g_mass_storage, g_ncm, g_ether
Cc: matthieu.castet@parrot.com
Reported-by: Michael Grzeschik <mgr@pengutronix.de>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Tested-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Delete global_phy due to we can get the phy from phy layer now
- using devm_usb_get_phy to instead of usb_get_phy
- delete the otg_set_peripheral, which should be handled by otg layer
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ENDPTFLUSH and ENDPTPRIME registers are set by software and clear
by hardware. There is a bit for each endpoint. When we are setting
a bit for an endpoint we should make sure we do not touch other
endpoint bit. There is a race condition if the hardware clear the
bit between the read and the write in hw_write.
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Michael Grzeschik <mgrzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AnZJ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.14-rc4
Here are 10 fixes for our current -rc cycle. It's likely
the last round of fixes for this merge window. All patches
have soaked for a long time and have all been tested in real
HW.
The most interesting fixes are a fix for enumeration of superspeed
hubs when MUSB is acting as host, and a remote-wakeup fix also on
MUSB.
Signed-of-by: Felipe Balbi <balbi@ti.com>
debugfs files to show the contents of important dsps registers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
schedule_delayed_work() takes the delay in jiffies, not msecs.
This bug slipped in with the recent reset logic cleanup
(8ed1fb790e: "usb: musb: finish suspend/reset work independently from
musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both the PM_RUNTIME and PM_SLEEP callbacks call into the common
msm_otg_{suspend,resume} routines, however these routines are only being
built when CONFIG_PM_SLEEP. In addition, msm_otg_{suspend,resume} also
depends on msm_hsusb_config_vddcx(), which is only built when
CONFIG_PM_SLEEP.
Fix the CONFIG_PM_RUNTIME, !CONFIG_PM_SLEEP case by changing the
preprocessor conditional, and moving msm_hsusb_config_vddcx().
While we're here, eliminate the CONFIG_PM conditional for setting
up the dev_pm_ops.
This address the following errors Russell King has hit doing randconfig
builds:
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_suspend':
drivers/usb/phy/phy-msm-usb.c:1691:2: error: implicit declaration of function 'msm_otg_suspend'
drivers/usb/phy/phy-msm-usb.c: In function 'msm_otg_runtime_resume':
drivers/usb/phy/phy-msm-usb.c:1699:2: error: implicit declaration of function 'msm_otg_resume'
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix possible NULL pointer dereference introduced in
commit 219580e (usb: f_fs: check quirk to pad epout
buf size when not aligned to maxpacketsize)
In cases we do wait with:
wait_event_interruptible(epfile->wait, (ep = epfile->ep));
for endpoint to be enabled, functionfs_bind() has not been called yet
and epfile->ffs->gadget is still NULL and the automatic variable 'gadget'
has been initialized with NULL at the point of its definition.
Later on it is used as a parameter to:
usb_ep_align_maybe(gadget, ep->ep, len)
which in turn dereferences it.
This patch fixes it by moving the actual assignment to the local 'gadget'
variable after the potential waiting has completed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to use gadget_is_otg to check if the gadget is really
otg support at runtime, other composite gadget drivers have already
followed this method.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.
Because of that, what used to be 8 bits long, has become 9 bits long.
Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.
So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits
This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.
[ balbi@ti.com : improve commit log a bit ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Debugfs function return an ERR_PTR if they compiled out. We don't need
to test for that here because if the debugfs file are compiled out then
it is ok to pass an ERR_PTR to debugfs_create_file() since it will just
be a no-op stub.
Debugfs return NULLs on error, but we don't need to test for that either
because debugfs_create_file() will accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A number of Kconfig entries default to (uppercase) "N". It was clearly
intended to use "default n". But since (lowercase) "n" is the default
anyway, these lines might as well be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SoCs earlier than sama5d3, they have the same number endpoints
and DMA channels. In driver code, they use the same definition
USBA_NR_ENDPOINTS for both endpoints and dma channels. However,
in sama5d3, it has different number for endpoints and DMA channels.
So, define a new macro USBA_NR_DMAs for DMA channels. And the
USBA_NR_ENDPOINS is not used anymore, remove it at the same time.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In sama5d3 SoC, there are 16 endpoints, which is different with
earlier SoCs (only have 7 endpoints). The USBA_NR_ENDPOINTS macro
is not suitable for sama5d3. So, get the endpoints number through
the udc->num_ep, which get from platform data for non-dt kernel,
or parse from dt node.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were made
obsolete in v3.11. They have not been used ever since. Setting them has
no effect. They can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
schedule_delayed_work() takes the delay in jiffies, not msecs. Fix the
caller sites in musb. This bug caused regressions with the cleanups
that went in for 3.14 (8ed1fb790e: "usb: musb: finish suspend/reset
work independently from musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
High-speed USB connections revert back to full-speed signalling when
the device goes into suspend. This takes several milliseconds, and
during that time it's not possible to tell reliably whether the device
has been disconnected.
On some platforms, the Wake-On-Disconnect circuitry gets confused
during this intermediate state. It generates a false wakeup signal,
which can prevent the controller from going to sleep.
To avoid this problem, this patch adds a 5-ms delay to the
ehci_bus_suspend() routine if any ports have to switch over to
full-speed signalling. (Actually, the delay was already present for
devices using a particular kind of PHY power management; the patch
merely causes the delay to be used more widely.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Peter Chen <Peter.Chen@freescale.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds asynchronous I/O support for FunctionFS endpoint files.
It adds ffs_epfile_aio_write() and ffs_epfile_aio_read() functions responsible
for preparing AIO operations.
It also modifies ffs_epfile_io() function, adding aio handling code. Instead
of extending list of parameters of this function, there is new struct
ffs_io_data which contains all information needed to perform I/O operation.
Pointer to this struct replaces "buf" and "len" parameters of ffs_epfile_io()
function. Allocated buffer is freed immediately only after sync operation,
because in async IO it's freed in complete funcion. For each async operation
an USB request is allocated, because it allows to have more than one request
queued on single endpoint.
According to changes in ffs_epfile_io() function, functions ffs_epfile_write()
and ffs_epfile_read() are updated to use new API.
For asynchronous I/O operations there is new request complete function named
ffs_epfile_async_io_complete(), which completes AIO operation, and frees
used memory.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds poll function for file representing ep0.
Ability of read from or write to ep0 file is related with actual state of ffs:
- When desctiptors or strings are not written yet, POLLOUT flag is set.
- If there is any event to read, POLLIN flag is set.
- If setup request was read, POLLIN and POLLOUT flag is set, to allow
send response (by performing I/O operation consistent with setup request
direction) or set stall (by performing I/O operation opposite setup
request direction).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes __ffs_ep0_queue_wait() function, which now returns number of
bytes transferred in USB request or error code in case of failure. This is
needed by ffs_ep0_read() function, when read data is copied to userspace.
It also cleans up code by removing usused variable ep0req_status.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The FFS_SETUP_STATUS macro could be trivialy replaced with an static
inline function but more importantly its name was tad confusing.
The name suggested it was a simple accessor macro but it actually
did change the state of the ffs_data structure perfomring
a FFS_SETUP_CANCELLED -> FFS_NO_SETUP transition. The name of the
function -- ffs_setup_state_clear_cancelled -- should better
describe what the function actually does.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since “cancelled” is spelled with two “l”s, rename FFS_SETUP_CANCELED
to FFS_SETUP_CANCELLED.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Consistently prefix function name with underscore if the function has to
be called with ffs_lock taken.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_alloc_dev and ffs_free_dev are used only in f_fs.c,
so make them static.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove trailing whitespace
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_dev->ffs_release_dev_callback should be accessed only if ffs_dev
is not NULL.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace kzalloc by devm_kzalloc and remove the kfree() calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When s3c_hsotg_ep_sethalt() function is called for ep0 it should be stalled
in the same way that it is in s3c_hsotg_process_control() function, because
SET_HALT for ep0 is delayed response for setup request. Endpoint 0, if
halted, it doesn't need CLEAR_HALT because it clears "stalled" state
automatically when next setup request is received.
For this reason this patch moves code setting ep0 to "stalled" state to new
function named s3c_hsotg_stall_ep0() which is called in
s3c_hsotg_process_control() function as an immediate response for setup
request, and in s3c_hsotg_ep_sethalt() function as a delayed response for
setup request.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When read data from g_printer, we see a Segmentation fault. eg:
Unable to handle kernel paging request at virtual address bf048000 pgd
= cf038000 [bf048000] *pgd=8e8cf811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM Modules linked in: bluetooth
rfcomm g_printer
CPU: 0 Not tainted (3.4.43-WR5.0.1.9_standard #1)
PC is at __copy_to_user_std+0x310/0x3a8 LR is at 0x4c808010
pc : [<c036e990>] lr : [<4c808010>] psr: 20000013
sp : cf883ea8 ip : 80801018 fp : cf883f24
r10: bf04706c r9 : 18a21205 r8 : 21953888
r7 : 201588aa r6 : 5109aa16 r5 : 0705aaa2 r4 : 5140aa8a
r3 : 0000004c r2 : 00000fdc r1 : bf048000 r0 : bef5fc3c
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 8f038019 DAC: 00000015 Process
g_printer_test. (pid: 661, stack limit = 0xcf8822e8)
Stack: (0xcf883ea8 to 0xcf884000)
3ea0: bf047068 00001fff bef5ecb9 cf882000 00001fff bef5ecb9
3ec0: 00001fff 00000000 cf2e8724 bf044d3c 80000013 80000013 00000001
bf04706c
3ee0: cf883f24 cf883ef0 c012e5ac c0324388 c007c8ac c0046298 00008180
cf29b900
3f00: 00002000 bef5ecb8 cf883f68 00000003 cf882000 cf29b900 cf883f54
cf883f28
3f20: c012ea08 bf044b0c c000eb88 00000000 cf883f7c 00000000 00000000
00002000
3f40: bef5ecb8 00000003 cf883fa4 cf883f58 c012eae8 c012e960 00000001
bef60cb8
3f60: 000000a8 c000eb88 00000000 00000000 cf883fa4 00000000 c014329c
00000000
3f80: 000000d4 41af63f0 00000003 c000eb88 cf882000 00000000 00000000
cf883fa8
3fa0: c000e920 c012eaa4 00000000 000000d4 00000003 bef5ecb8 00002000
bef5ecb8
3fc0: 00000000 000000d4 41af63f0 00000003 b6f534c0 00000000 419f9000
00000000
3fe0: 00000000 bef5ecac 000086d9 41a986bc 60000010 00000003 0109608a
0088828a
Code: f5d1f07c e8b100f0 e1a03c2e e2522020 (e8b15300) ---[ end trace
97e2618e250e3377 ]--- Segmentation fault
The root cause is the dev->rx_buffers list has been broken.
When we call printer_read(), the following call tree is triggered:
printer_read()
|
+---setup_rx_reqs(req)
| |
| +---usb_ep_queue(req)
| | |
| | +---...
| | |
| | +---rx_complete(req).
| |
| +---add the req to dev->rx_reqs_active
|
+---while(!list_empty(&dev->rx_buffers)))
The route happens when we don't use DMA or fail to start DMA in USB
driver. We can see: in the case, in rx_complete() it will add the req
to dev->rx_buffers. meanwhile we see that we will also add the req to
dev->rx_reqs_active after usb_ep_queue() return, so this adding will
break the dev->rx_buffers out.
After, when we call list_empty() to check dev->rx_buffers in while(),
due to can't check correctly dev->rx_buffers, so the Segmentation fault
occurs when copy_to_user() is called.
Signed-off-by: wenlin.kang <wenlin.kang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The problem occurs in follow path.
printer_read()
|
+---setup_rx_reqs()
|
+---usb_ep_queue()
|
+---...
|
+---rx_complete()
Although it is clear from code, we can't get it normally.
only when we enable some spin_lock debug config option, we can find it.
eg:
BUG: spinlock lockup on CPU#0, g_printer_test_/584
lock: bf05e158, .magic: dead4ead, .owner: g_printer_test_/584, .owner_cpu: 0
[<c0016e1c>] (unwind_backtrace+0x0/0x104) from [<c067aef8>] (dump_stack+0x20/0x24)
[<c067aef8>] (dump_stack+0x20/0x24) from [<c0680bec>] (spin_dump+0x8c/0x94)
[<c0680bec>] (spin_dump+0x8c/0x94) from [<c039071c>] (do_raw_spin_lock+0x128/0x154)
[<c039071c>] (do_raw_spin_lock+0x128/0x154) from [<c0685618>] (_raw_spin_lock_irqsave+0x64/0x70)
[<c0685618>] (_raw_spin_lock_irqsave+0x64/0x70) from [<bf05b4e8>] (rx_complete+0x54/0x10c [g_printer])
[<bf05b4e8>] (rx_complete+0x54/0x10c [g_printer]) from [<c0480478>] (musb_g_giveback+0x78/0x88)
[<c0480478>] (musb_g_giveback+0x78/0x88) from [<c048060c>] (rxstate+0xa0/0x10c)
[<c048060c>] (rxstate+0xa0/0x10c) from [<c0480d50>] (musb_ep_restart+0x44/0x70)
[<c0480d50>] (musb_ep_restart+0x44/0x70) from [<c0480fe4>] (musb_gadget_queue+0xe8/0xf8)
[<c0480fe4>] (musb_gadget_queue+0xe8/0xf8) from [<bf05b2b0>] (setup_rx_reqs+0xa4/0x178 [g_printer])
[<bf05b2b0>] (setup_rx_reqs+0xa4/0x178 [g_printer]) from [<bf05bb58>] (printer_read+0x9c/0x3f4 [g_printer])
[<bf05bb58>] (printer_read+0x9c/0x3f4 [g_printer]) from [<c01387f0>] (vfs_read+0xb4/0x144)
[<c01387f0>] (vfs_read+0xb4/0x144) from [<c01388d0>] (sys_read+0x50/0x124)
[<c01388d0>] (sys_read+0x50/0x124) from [<c000e900>] (ret_fast_syscall+0x0/0x3c)
The root cause is that we use the same lock two time in a path, so to avoid
the deadlock, we need to unlock in setup_rx_reqs(), and only unlock.
Signed-off-by: wenlin.kang <wenlin.kang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes the following compilation warning:
drivers/usb/gadget/s3c-hsudc.c: In function ‘s3c_hsudc_probe’:
drivers/usb/gadget/s3c-hsudc.c:1347:1: warning: label ‘err_add_device’
defined but not used [-Wunused-label]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742d3
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):
drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use %pad for dma_addr_t to avoid the following build warnings
in printks.
drivers/usb/gadget/s3c-hsotg.c: In function 's3c_hsotg_start_req'
drivers/usb/gadget/s3c-hsotg.c:722:3: warning: format '%x' expects argument of type 'unsigned int' but argument 6 has type
'dma_addr_t' [-Wformat]
drivers/usb/gadget/s3c-hsotg.c:792:3: warning: format '%x' expects argument of type 'unsigned int' but argument 5 has type
'dma_addr_t' [-Wformat]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The readsl and writesl I/O accessors are only defined on some
architectures. The driver currently depends on CONFIG_ARM because
the build breaks on x86, in particular. Switch to use of ioread32_rep
and iowrite32_rep to fix build on all architectures and remove the
CONFIG_ARM dependency.
Also update printk formatting to handle a long long dma_addr_t to avoid
warnings on !32-bit architectures.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3dc6475 ("bcm63xx_enet: add support Broadcom BCM6345 Ethernet")
changed the ENETDMA[CS] macros such that they are no longer macros, but
actual register offset definitions. The bcm63xx_udc driver was not
updated, and as a result, causes the following build error to pop up:
CC drivers/usb/gadget/u_ether.o
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_write':
drivers/usb/gadget/bcm63xx_udc.c:642:24: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c: In function 'iudma_reset_channel':
drivers/usb/gadget/bcm63xx_udc.c:698:46: error: called object '0' is not
a function
drivers/usb/gadget/bcm63xx_udc.c:700:49: error: called object '0' is not
a function
Fix this by updating usb_dmac_{read,write}l and usb_dmas_{read,write}l to
take an extra channel argument, and use the channel width
(ENETDMA_CHAN_WIDTH) to offset the register we want to access, hence
doing again what the macro implicitely did for us.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pass value instead of address as expected by 'usb_ep_set_maxpacket_limit'.
Fixes the following compilation error introduced by commit e117e742d3
("usb: gadget: add "maxpacket_limit" field to struct usb_ep"):
drivers/usb/gadget/s3c2410_udc.c: In function ‘s3c2410_udc_reinit’:
drivers/usb/gadget/s3c2410_udc.c:1632:3: error:
cannot take address of bit-field ‘maxpacket’
usb_ep_set_maxpacket_limit(&ep->ep, &ep->ep.maxpacket);
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.
e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.
[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
