Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending the
set of supported features for additional SoCs in the QSEECOM, LLCC
and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip
sparx5 and amlogic reset drivers to support additional chips,
plus a few minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/soc, drivers/bus,
and drivers/memory, including changing back the .remove_new callback
to .remove, as well as a few other updates for freescale (powerpc)
soc drivers, NXP i.MX soc drivers, cznic turris platform driver, memory
controller drviers, TI OMAP SoC drivers, and Tegra firmware drivers
-----BEGIN PGP SIGNATURE-----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=xeCE
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
Bindings:
- Enable dtc "interrupt_provider" warnings for binding examples.
Fix the warnings in fsl,mu-msi and ti,sci-inta due to this.
- Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
altr,fpga-passive-serial to DT schema format
- Add some documentation on the different forms of YAML text blocks
which are a constant source of review comments
- Fix some schema errors in constraints for arrays
- Add compatibles for qcom,sar2130p-pdc and onnn,adt7462
DT core:
- Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
- Add some warnings on deprecated address handling
- Rework early_init_dt_scan() so the arch can pass in the phys address
of the DTB as __pa() is not always valid to use. This fixes a warning
for arm64 with kexec.
- Add and use some new DT graph iterators for iterating over ports and
endpoints
- Rework reserved-memory handling to be sized dynamically for fixed
regions
- Optimize of_modalias() to avoid a strlen() call
- Constify struct device_node and property pointers where ever possible
-----BEGIN PGP SIGNATURE-----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=NCYS
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Enable dtc "interrupt_provider" warnings for binding examples. Fix
the warnings in fsl,mu-msi and ti,sci-inta due to this.
- Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
altr,fpga-passive-serial to DT schema format
- Add some documentation on the different forms of YAML text blocks
which are a constant source of review comments
- Fix some schema errors in constraints for arrays
- Add compatibles for qcom,sar2130p-pdc and onnn,adt7462
DT core:
- Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
- Add some warnings on deprecated address handling
- Rework early_init_dt_scan() so the arch can pass in the phys
address of the DTB as __pa() is not always valid to use. This fixes
a warning for arm64 with kexec.
- Add and use some new DT graph iterators for iterating over ports
and endpoints
- Rework reserved-memory handling to be sized dynamically for fixed
regions
- Optimize of_modalias() to avoid a strlen() call
- Constify struct device_node and property pointers where ever
possible"
* tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (36 commits)
of: Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
dt-bindings: interrupt-controller: qcom,pdc: Add SAR2130P compatible
of/address: Rework bus matching to avoid warnings
of: WARN on deprecated #address-cells/#size-cells handling
of/fdt: Don't use default address cell sizes for address translation
dt-bindings: Enable dtc "interrupt_provider" warnings
of/fdt: add dt_phys arg to early_init_dt_scan and early_init_dt_verify
dt-bindings: cache: qcom,llcc: Fix X1E80100 reg entries
dt-bindings: watchdog: convert zii,rave-sp-wdt.txt to yaml format
dt-bindings: input: convert zii,rave-sp-pwrbutton.txt to yaml
media: xilinx-tpg: use new of_graph functions
fbdev: omapfb: use new of_graph functions
gpu: drm: omapdrm: use new of_graph functions
ASoC: audio-graph-card2: use new of_graph functions
ASoC: audio-graph-card: use new of_graph functions
ASoC: test-component: use new of_graph functions
of: property: use new of_graph functions
of: property: add of_graph_get_next_port_endpoint()
of: property: add of_graph_get_next_port()
of: module: remove strlen() call in of_modalias()
...
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCZyn4gxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwFJZAP0fjXG07qnGp1Sgai/pmCesg5xJ
PAEL5/hKaYwQsAQHhwEAwaJg+kVeb74ez3ae4akyvngasJJT9LLDmqWEdxPIcw0=
=cyUW
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=rxJh
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux into soc/drivers
Reset controller updates for v6.13
* Split the Amlogic reset-meson driver into platform and auxiliary
bus drivers. Add support for the reset controller in the G12 and
SM1 audio clock controllers.
* Replace the list of boolean parameters to the internal
reset_control_get functions with an enum reset_flags bitfield,
to make the code more self-descriptive.
* Add devres helpers to request pre-deasserted (and automatically
re-asserting during cleanup) reset controls. This allows reducing
boilerplate in drivers that deassert resets for the lifetime of a
device.
* Use the new auto-deasserting devres helpers in reset-uniphier-glue
as an example.
* Add support for the LAN966x PCI device in drivers/misc, as a
dependency for the following reset-microchip-sparx5 patches.
* Add support for being used on the LAN966x PCI device to the
reset-microchip-sparx5 driver.
Commit 86f134941a ("MAINTAINERS: Add the Microchip LAN966x PCI driver
entry") introduces a trivial merge conflict with commit 7280f01e79
("net: lan969x: add match data for lan969x") from the net-next tree [1].
[1] https://lore.kernel.org/all/20241101122505.3eacd183@canb.auug.org.au/
* tag 'reset-for-v6.13' of git://git.pengutronix.de/pza/linux: (21 commits)
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
reset: mchp: sparx5: set the dev member of the reset controller
reset: mchp: sparx5: Allow building as a module
reset: mchp: sparx5: Add MCHP_LAN966X_PCI dependency
reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x
MAINTAINERS: Add the Microchip LAN966x PCI driver entry
misc: Add support for LAN966x PCI device
reset: uniphier-glue: Use devm_reset_control_bulk_get_shared_deasserted()
reset: Add devres helpers to request pre-deasserted reset controls
reset: replace boolean parameters with flags parameter
reset: amlogic: Fix small whitespace issue
reset: amlogic: add auxiliary reset driver support
reset: amlogic: split the device core and platform probe
reset: amlogic: move drivers to a dedicated directory
reset: amlogic: add reset status support
reset: amlogic: use reset number instead of register count
reset: amlogic: add driver parameters
reset: amlogic: make parameters unsigned
reset: amlogic: use generic data matching function
...
Link: https://lore.kernel.org/r/20241105105229.3729474-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=9o9y
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Enable device-specific ACS-like functionality even if the device
doesn't advertise an ACS capability, which got broken when adding
fancy ACS kernel parameter (Jason Gunthorpe)
* tag 'pci-v6.12-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix pci_enable_acs() support for the ACS quirks
There are ACS quirks that hijack the normal ACS processing and deliver to
to special quirk code. The enable path needs to call
pci_dev_specific_enable_acs() and then pci_dev_specific_acs_enabled() will
report the hidden ACS state controlled by the quirk.
The recent rework got this out of order and we should try to call
pci_dev_specific_enable_acs() regardless of any actual ACS support in the
device.
As before command line parameters that effect standard PCI ACS don't
interact with the quirk versions, including the new config_acs= option.
Link: https://lore.kernel.org/r/0-v1-f96b686c625b+124-pci_acs_quirk_fix_jgg@nvidia.com
Fixes: 47c8846a49 ("PCI: Extend ACS configurability")
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/e89107da-ac99-4d3a-9527-a4df9986e120@kernel.org
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1229019
Tested-by: Steffen Dirkwinkel <me@steffen.cc>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=L6G0
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Hold the rescan lock while adding devices to avoid race with
concurrent pwrctl rescan that can lead to a crash (Bartosz
Golaszewski)
- Avoid binding pwrctl driver to QCom WCN wifi if the DT lacks the
necessary PMU regulator descriptions (Bartosz Golaszewski)
* tag 'pci-v6.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctl: Abandon QCom WCN probe on pre-pwrseq device-trees
PCI: Hold rescan lock while adding devices during host probe
Add a PCI driver that handles the LAN966x PCI device using a device-tree
overlay. This overlay is applied to the PCI device DT node and allows to
describe components that are present in the device.
The memory from the device-tree is remapped to the BAR memory thanks to
"ranges" properties computed at runtime by the PCI core during the PCI
enumeration.
The PCI device itself acts as an interrupt controller and is used as the
parent of the internal LAN966x interrupt controller to route the
interrupts to the assigned PCI INTx interrupt.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # quirks.c
Link: https://lore.kernel.org/r/20241014124636.24221-2-herve.codina@bootlin.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Old device trees for some platforms already define wifi nodes for the WCN
family of chips since before power sequencing was added upstream.
These nodes don't consume the regulator outputs from the PMU, and if we
allow this driver to bind to one of such "incomplete" nodes, we'll see a
kernel log error about the infinite probe deferral.
Extend the driver by adding a platform data struct matched against the
compatible. This struct contains the pwrseq target string as well as a
validation function called right after entering probe().
For Qualcomm WCN models, check the existence of the regulator supply
property that indicates the DT is already using power sequencing and return
-ENODEV if it's not there, indicating to the driver model that the device
should not be bound to the pwrctl driver.
Link: https://lore.kernel.org/r/20241007092447.18616-1-brgl@bgdev.pl
Fixes: 6140d185a4 ("PCI/pwrctl: Add a PCI power control driver for power sequenced devices")
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/Zv565olMDDGHyYVt@hovoldconsulting.com/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_register_io_range() does not modify the passed in fwnode_handle, so
make it const.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241010-dt-const-v1-1-87a51f558425@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Since adding the PCI power control code, we may end up with a race between
the pwrctl platform device rescanning the bus and host controller probe
functions. The latter need to take the rescan lock when adding devices or
we may end up in an undefined state having two incompletely added devices
and hit the following crash when trying to remove the device over sysfs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
Call trace:
__pi_strlen+0x14/0x150
kernfs_find_ns+0x80/0x13c
kernfs_remove_by_name_ns+0x54/0xf0
sysfs_remove_bin_file+0x24/0x34
pci_remove_resource_files+0x3c/0x84
pci_remove_sysfs_dev_files+0x28/0x38
pci_stop_bus_device+0x8c/0xd8
pci_stop_bus_device+0x40/0xd8
pci_stop_and_remove_bus_device_locked+0x28/0x48
remove_store+0x70/0xb0
dev_attr_store+0x20/0x38
sysfs_kf_write+0x58/0x78
kernfs_fop_write_iter+0xe8/0x184
vfs_write+0x2dc/0x308
ksys_write+0x7c/0xec
Fixes: 4565d2652a ("PCI/pwrctl: Add PCI power control core code")
Link: https://lore.kernel.org/r/20241003084342.27501-1-brgl@bgdev.pl
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konradybcio@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmbseugUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxdwxAAvdvDyTuiPo2R8pQtvKg4YL2IUnK5
UR28mBxZDK5DFhLtD/QzmVVG/eaLY6bJHthHgJgTApzekkqU0h9dcRI0eegXrvcz
I3HRsZK2yatUky9l8O148OLzF897r7vXL3QtGe6qjKU+9D83IEeooLKgBca+GoBC
bRLvG/fYRzdjOe8UHFqCoeMIg3IOY7CNifvFOihAGpJpxfZQktj6hSKu6q7BL1Rx
NRgYlxh0eLcb7vAJqz6RZpQ8PRCwhAjlDuu0BOkES8/6EwisD1xUh3qdDxfVgNA6
FpcAb/53yr46cs4tM9ZTwluka86AskuXj3jwSKf7nE3zqr4nM9OD3sGOSYzK8UdE
EDBKj+9iEpYRC6rJMk5gNH2AZkR1OEpNUisR6+kEn81A9yNNoTmkHdHUOWo8TuxD
btc0sTM+eWApvTiZwgL4VjMZulQllV51K8tcfvODRhlMkbOPNWGWdmpWqEbUS2HU
i7+zzQC3DC5iPlAKgRSeYB0aad6la6brqPW16sGhGovNhgwbzakDLCUJJGn/LNuO
wd0UNpJTnHlfChbvNh2bBxiMOo0cab1tJ5Jp97STQYhLg2nW93s/dAfdpSAsYO4S
5YzjSADWeyeuDsHE1RdUdDvYAPMb1VZBUd2OSHis5zw7kmh25c9KYXEkDJ25q/ju
sVXK4oMNW/Gnd5M=
=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS but
does provide ACS-like features (Subramanian Ananthanarayanan)
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
* pci/quirks:
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
PCI: Add ACS quirk for Qualcomm SA8775P
- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups without
having to stomp on the core's pdev->dev.groups (Lukas Wunner)
* pci/sysfs:
s390/pci: Stop usurping pdev->dev.groups
- Wait for each level of downstream bus, not just the first, to become
accessible before restoring devices on that bus (Ilpo Järvinen)
* pci/reset:
PCI: Wait for Link before restoring Downstream Buses
- Initialize leds class earlier (with an unfortunate Makefile ordering
change) so the PCI NPEM driver can use it (Mariusz Tkaczyk)
- Add Native PCIe Enclosure Management (NPEM) support for sysfs control of
NVMe RAID storage indicators (ok/fail/locate/rebuild/etc) (Mariusz
Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which is
functionally similar to NPEM but mediated by platform firmware (Mariusz
Tkaczyk)
* pci/npem:
PCI/NPEM: Add _DSM PCIe SSD status LED management
PCI/NPEM: Add Native PCIe Enclosure Management support
leds: Init leds class earlier
- Add function 0 DMA alias quirk for Glenfly Arise audio function, which
uses the function 0 Requester ID (WangYuli)
* pci/iommu:
PCI: Add function 0 DMA alias quirk for Glenfly Arise chip
- Clear LBMS bit after a manual link retrain so we don't try to retrain a
link when there's no downstream device anymore (Maciej W. Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance to use
higher speeds (Maciej W. Rozycki)
- Correct interpretation of pcie_retrain_link() return status and update it
to return 0/errno instead of true/false (Maciej W. Rozycki)
* pci/enumeration:
PCI: Use an error code with PCIe failed link retraining
PCI: Correct error reporting with PCIe failed link retraining
PCI: Revert to the original speed after PCIe failed link retraining
PCI: Clear the LBMS bit after a link retrain
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions() (Philipp
Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp Stanner)
* pci/devres:
drm/ast: Request PCI BAR with devres
PCI: Deprecate pcim_iomap_regions() in favor of pcim_iomap_region()
drm/vboxvideo: Add PCI region request
PCI: Make pcim_request_region() a public function
- Wait for device readiness after reset by polling Vendor ID and looking
for Configuration RRS instead of polling the Command register and looking
for non-error completions (Bjorn Helgaas)
- Fix an aardvark issue with emulating Configuration RRS for two-byte reads
of Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
- Rename CRS Completion Status to RRS to match spec usage (Bjorn Helgaas)
* pci/crs:
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
Including:
- Core changes:
- Allow ATS on VF when parent device is identity mapped.
- Optimize unmap path on ARM io-pagetable implementation.
- Use of_property_present().
- ARM-SMMU changes:
- SMMUv2:
- Devicetree binding updates for Qualcomm MMU-500 implementations.
- Extend workarounds for broken Qualcomm hypervisor to avoid
touching features that are not available (e.g. 16KiB page
support, reserved context banks).
- SMMUv3:
- Support for NVIDIA's custom virtual command queue hardware.
- Fix Stage-2 stall configuration and extend tests to cover this
area.
- A bunch of driver cleanups, including simplification of the
master rbtree code.
- Plus minor cleanups and fixes across both drivers.
- Intel VT-d changes:
- Retire si_domain and convert to use static identity domain.
- Batched IOTLB/dev-IOTLB invalidation.
- Small code refactoring and cleanups.
- AMD-Vi changes:
- Cleanup and refactoring of io-pagetable code.
- Add parameter to limit the used io-pagesizes.
- Other cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=1QvI
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core changes:
- Allow ATS on VF when parent device is identity mapped
- Optimize unmap path on ARM io-pagetable implementation
- Use of_property_present()
ARM-SMMU changes:
- SMMUv2:
- Devicetree binding updates for Qualcomm MMU-500 implementations
- Extend workarounds for broken Qualcomm hypervisor to avoid
touching features that are not available (e.g. 16KiB page
support, reserved context banks)
- SMMUv3:
- Support for NVIDIA's custom virtual command queue hardware
- Fix Stage-2 stall configuration and extend tests to cover this
area
- A bunch of driver cleanups, including simplification of the
master rbtree code
- Minor cleanups and fixes across both drivers
Intel VT-d changes:
- Retire si_domain and convert to use static identity domain
- Batched IOTLB/dev-IOTLB invalidation
- Small code refactoring and cleanups
AMD-Vi changes:
- Cleanup and refactoring of io-pagetable code
- Add parameter to limit the used io-pagesizes
- Other cleanups and fixes"
* tag 'iommu-updates-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (77 commits)
dt-bindings: arm-smmu: Add compatible for QCS8300 SoC
iommu/amd: Test for PAGING domains before freeing a domain
iommu/amd: Fix argument order in amd_iommu_dev_flush_pasid_all()
iommu/amd: Add kernel parameters to limit V1 page-sizes
iommu/arm-smmu-v3: Reorganize struct arm_smmu_ctx_desc_cfg
iommu/arm-smmu-v3: Add types for each level of the CD table
iommu/arm-smmu-v3: Shrink the cdtab l1_desc array
iommu/arm-smmu-v3: Do not use devm for the cd table allocations
iommu/arm-smmu-v3: Remove strtab_base/cfg
iommu/arm-smmu-v3: Reorganize struct arm_smmu_strtab_cfg
iommu/arm-smmu-v3: Add types for each level of the 2 level stream table
iommu/arm-smmu-v3: Add arm_smmu_strtab_l1/2_idx()
iommu/arm-smmu-qcom: apply num_context_bank fixes for SDM630 / SDM660
iommu/arm-smmu-v3: Use the new rb tree helpers
dt-bindings: arm-smmu: document the support on SA8255p
iommu/tegra241-cmdqv: Do not allocate vcmdq until dma_set_mask_and_coherent
iommu/tegra241-cmdqv: Drop static at local variable
iommu/tegra241-cmdqv: Fix ioremap() error handling in probe()
iommu/amd: Do not set the D bit on AMD v2 table entries
iommu/amd: Correct the reported page sizes from the V1 table
...
- Check return value in acpi_db_convert_to_package() (Pei Xiao).
- Detect FACS and allow setting the waking vector on reduced-hardware
ACPI platforms (Jiaqing Zhao).
- Allow ACPICA to represent semaphores as integers (Adrien Destugues).
- Complete CXL 3.0 CXIMS structures support in ACPICA (Zhang Rui).
- Make ACPICA support SPCR version 4 and add RISC-V SBI Subtype to
DBG2 (Sia Jee Heng).
- Implement the Dword_PCC Resource Descriptor Macro in ACPICA (Jose
Marinho).
- Correct the typo in struct acpi_mpam_msc_node member (Punit Agrawal).
- Implement ACPI_WARNING_ONCE() and ACPI_ERROR_ONCE() and use them to
prevent a Stall() violation warning from being printed every time
this takes place (Vasily Khoruzhick).
- Allow PCC Data Type in MCTP resource (Adam Young).
- Fix memory leaks on acpi_ps_get_next_namepath()
and acpi_ps_get_next_field() failures (Armin Wolf).
- Add support for supressing leading zeros in hex strings when
converting them to integers and update integer-to-hex-string
conversions in ACPICA (Armin Wolf).
- Add support for Windows 11 22H2 _OSI string (Armin Wolf).
- Avoid warning for Dump Functions in ACPICA (Adam Lackorzynski).
- Add extended linear address mode to HMAT MSCIS in ACPICA (Dave
Jiang).
- Handle empty connection_node in iasl (Aleksandrs Vinarskis).
- Allow for more flexibility in _DSM args (Saket Dumbre).
- Setup for ACPICA release 20240827 (Saket Dumbre).
- Add ACPI device enumeration support for interrupt controller probing
including taking dependencies into account (Sunil V L).
- Implement ACPI-based interrupt controller probing on RISC-V (Sunil V L).
- Add ACPI support for AIA in riscv-intc and add ACPI support to
riscv-imsic, riscv-aplic, and sifive-plic (Sunil V L).
- Do not release locks during operation region accesses in the ACPI EC
driver (Rafael Wysocki).
- Fix up the _STR handling in the ACPI device object sysfs interface,
make it represent the device object attributes as an attribute group
and make it rely on driver core functionality for sysfs attrubute
management (Thomas Weißschuh).
- Extend error messages printed to the kernel log when acpi_evaluate_dsm()
fails to include revision and function number (David Wang).
- Add a new AMDI0015 platform device ID to the ACPi APD driver for AMD
SoCs (Shyam Sundar S K).
- Use the driver core for the async probing management in the ACPI
battery driver (Thomas Weißschuh).
- Remove redundant initalizations of a local variable to NULL from the
ACPI battery driver (Ilpo Järvinen).
- Remove unneeded check in tps68470_pmic_opregion_probe() (Aleksandr
Mishin).
- Add support for setting the EPP register through the ACPI CPPC sysfs
interface if it is in FFH (Mario Limonciello).
- Fix MASK_VAL() usage in the ACPI CPPC library (Clément Léger).
- Reduce the log level of a per-CPU message about idle states in the
ACPI processor driver (Li RongQing).
- Fix crash in exit_round_robin() in the ACPI processor aggregator
device (PAD) driver (Seiji Nishikawa).
- Add force_vendor quirk for Panasonic Toughbook CF-18 in the ACPI
backlight driver (Hans de Goede).
- Make the DMI checks related to backlight handling on Lenovo Yoga
Tab 3 X90F less strict (Hans de Goede).
- Enforce native backlight handling on Apple MacbookPro9,2 (Esther
Shimanovich).
- Add IRQ override quirks for Asus Vivobook Go E1404GAB and MECHREV
GM7XG0M, and refine the TongFang GMxXGxx quirk (Li Chen, Tamim Khan,
Werner Sembach).
- Quirk ASUS ROG M16 to default to S3 sleep (Luke D. Jones).
- Define and use symbols for device and class name lengths in the ACPI
bus type code and make the code use strscpy() instead of strcpy() in
several places (Muhammad Qasim Abdul Majeed).
-----BEGIN PGP SIGNATURE-----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=XHaD
-----END PGP SIGNATURE-----
Merge tag 'acpi-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream version
20240827, add support for ACPI-based enumeration of interrupt
controllers on RISC-V along with some related irqchip updates, clean
up the ACPI device object sysfs interface, add some quirks for
backlight handling and IRQ overrides, fix assorted issues and clean up
code.
Specifics:
- Check return value in acpi_db_convert_to_package() (Pei Xiao)
- Detect FACS and allow setting the waking vector on reduced-hardware
ACPI platforms (Jiaqing Zhao)
- Allow ACPICA to represent semaphores as integers (Adrien Destugues)
- Complete CXL 3.0 CXIMS structures support in ACPICA (Zhang Rui)
- Make ACPICA support SPCR version 4 and add RISC-V SBI Subtype to
DBG2 (Sia Jee Heng)
- Implement the Dword_PCC Resource Descriptor Macro in ACPICA (Jose
Marinho)
- Correct the typo in struct acpi_mpam_msc_node member (Punit
Agrawal)
- Implement ACPI_WARNING_ONCE() and ACPI_ERROR_ONCE() and use them to
prevent a Stall() violation warning from being printed every time
this takes place (Vasily Khoruzhick)
- Allow PCC Data Type in MCTP resource (Adam Young)
- Fix memory leaks on acpi_ps_get_next_namepath() and
acpi_ps_get_next_field() failures (Armin Wolf)
- Add support for supressing leading zeros in hex strings when
converting them to integers and update integer-to-hex-string
conversions in ACPICA (Armin Wolf)
- Add support for Windows 11 22H2 _OSI string (Armin Wolf)
- Avoid warning for Dump Functions in ACPICA (Adam Lackorzynski)
- Add extended linear address mode to HMAT MSCIS in ACPICA (Dave
Jiang)
- Handle empty connection_node in iasl (Aleksandrs Vinarskis)
- Allow for more flexibility in _DSM args (Saket Dumbre)
- Setup for ACPICA release 20240827 (Saket Dumbre)
- Add ACPI device enumeration support for interrupt controller
probing including taking dependencies into account (Sunil V L)
- Implement ACPI-based interrupt controller probing on RISC-V
(Sunil V L)
- Add ACPI support for AIA in riscv-intc and add ACPI support to
riscv-imsic, riscv-aplic, and sifive-plic (Sunil V L)
- Do not release locks during operation region accesses in the ACPI
EC driver (Rafael Wysocki)
- Fix up the _STR handling in the ACPI device object sysfs interface,
make it represent the device object attributes as an attribute
group and make it rely on driver core functionality for sysfs
attrubute management (Thomas Weißschuh)
- Extend error messages printed to the kernel log when
acpi_evaluate_dsm() fails to include revision and function number
(David Wang)
- Add a new AMDI0015 platform device ID to the ACPi APD driver for
AMD SoCs (Shyam Sundar S K)
- Use the driver core for the async probing management in the ACPI
battery driver (Thomas Weißschuh)
- Remove redundant initalizations of a local variable to NULL from
the ACPI battery driver (Ilpo Järvinen)
- Remove unneeded check in tps68470_pmic_opregion_probe() (Aleksandr
Mishin)
- Add support for setting the EPP register through the ACPI CPPC
sysfs interface if it is in FFH (Mario Limonciello)
- Fix MASK_VAL() usage in the ACPI CPPC library (Clément Léger)
- Reduce the log level of a per-CPU message about idle states in the
ACPI processor driver (Li RongQing)
- Fix crash in exit_round_robin() in the ACPI processor aggregator
device (PAD) driver (Seiji Nishikawa)
- Add force_vendor quirk for Panasonic Toughbook CF-18 in the ACPI
backlight driver (Hans de Goede)
- Make the DMI checks related to backlight handling on Lenovo Yoga
Tab 3 X90F less strict (Hans de Goede)
- Enforce native backlight handling on Apple MacbookPro9,2 (Esther
Shimanovich)
- Add IRQ override quirks for Asus Vivobook Go E1404GAB and MECHREV
GM7XG0M, and refine the TongFang GMxXGxx quirk (Li Chen, Tamim
Khan, Werner Sembach)
- Quirk ASUS ROG M16 to default to S3 sleep (Luke D. Jones)
- Define and use symbols for device and class name lengths in the
ACPI bus type code and make the code use strscpy() instead of
strcpy() in several places (Muhammad Qasim Abdul Majeed)"
* tag 'acpi-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
ACPI: resource: Add another DMI match for the TongFang GMxXGxx
ACPI: CPPC: Add support for setting EPP register in FFH
ACPI: PM: Quirk ASUS ROG M16 to default to S3 sleep
ACPI: video: Add force_vendor quirk for Panasonic Toughbook CF-18
ACPI: battery: use driver core managed async probing
ACPI: button: Use strscpy() instead of strcpy()
ACPI: resource: Skip IRQ override on Asus Vivobook Go E1404GAB
ACPI: CPPC: Fix MASK_VAL() usage
irqchip/sifive-plic: Add ACPI support
ACPICA: Setup for ACPICA release 20240827
ACPICA: Allow for more flexibility in _DSM args
ACPICA: iasl: handle empty connection_node
ACPICA: HMAT: Add extended linear address mode to MSCIS
ACPICA: Avoid warning for Dump Functions
ACPICA: Add support for Windows 11 22H2 _OSI string
ACPICA: Update integer-to-hex-string conversions
ACPICA: Add support for supressing leading zeros in hex strings
ACPICA: Allow for supressing leading zeros when using acpi_ex_convert_to_ascii()
ACPICA: Fix memory leak if acpi_ps_get_next_field() fails
ACPICA: Fix memory leak if acpi_ps_get_next_namepath() fails
...
The pci_bus_release_domain_nr() API is supposed to free the domain
number allocated by pci_bus_find_domain_nr(). Most of the callers of
pci_bus_find_domain_nr(), store the domain number in pci_bus::domain_nr.
As such, the pci_bus_release_domain_nr() implicitly frees the domain
number by dereferencing 'struct pci_bus'. However, one of the callers
of this API, the PCI endpoint subsystem, doesn't have 'struct pci_bus',
so it only passes NULL. Due to this, the API will end up dereferencing
the NULL pointer.
To fix this issue, pass the domain number to this API explicitly. Since
'struct pci_bus' is not used for anything else other than extracting the
domain number, it makes sense to pass the domain number directly.
Fixes: 0328947c50 ("PCI: endpoint: Assign PCI domain number for endpoint controllers")
Closes: https://lore.kernel.org/linux-pci/c0c40ddb-bf64-4b22-9dd1-8dbb18aa2813@stanley.mountain
Link: https://lore.kernel.org/linux-pci/20240912053025.25314-1-manivannan.sadhasivam@linaro.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----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=i+4X
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.11-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Prevent a possible deadlock (reported by lockdep) when a driver
relinquishes a pci_dev, another driver claims it, and one uses
managed pcim_enable_device() and the other doesn't (Philipp Stanner)
* tag 'pci-v6.11-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: Fix potential deadlock in pcim_intx()
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
