Commit 55b665b026 ("KVM: PPC: Book3S HV: Provide a way for userspace
to get/set per-vCPU areas") includes a check on the length of the
dispatch trace log (DTL) to make sure the buffer is at least one entry
long. This is appropriate when registering a buffer, but the
interface also allows for any existing buffer to be unregistered by
specifying a zero address. In this case the length check is not
appropriate. This makes the check conditional on the address being
non-zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the code that accounts stolen time tends to overestimate the
stolen time, and will sometimes report more stolen time in a DTL
(dispatch trace log) entry than has elapsed since the last DTL entry.
This can cause guests to underflow the user or system time measured
for some tasks, leading to ridiculous CPU percentages and total runtimes
being reported by top and other utilities.
In addition, the current code was designed for the previous policy where
a vcore would only run when all the vcpus in it were runnable, and so
only counted stolen time on a per-vcore basis. Now that a vcore can
run while some of the vcpus in it are doing other things in the kernel
(e.g. handling a page fault), we need to count the time when a vcpu task
is preempted while it is not running as part of a vcore as stolen also.
To do this, we bring back the BUSY_IN_HOST vcpu state and extend the
vcpu_load/put functions to count preemption time while the vcpu is
in that state. Handling the transitions between the RUNNING and
BUSY_IN_HOST states requires checking and updating two variables
(accumulated time stolen and time last preempted), so we add a new
spinlock, vcpu->arch.tbacct_lock. This protects both the per-vcpu
stolen/preempt-time variables, and the per-vcore variables while this
vcpu is running the vcore.
Finally, we now don't count time spent in userspace as stolen time.
The task could be executing in userspace on behalf of the vcpu, or
it could be preempted, or the vcpu could be genuinely stopped. Since
we have no way of dividing up the time between these cases, we don't
count any of it as stolen.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the Book3S HV code implements a policy on multi-threaded
processors (i.e. POWER7) that requires all of the active vcpus in a
virtual core to be ready to run before we run the virtual core.
However, that causes problems on reset, because reset stops all vcpus
except vcpu 0, and can also reduce throughput since all four threads
in a virtual core have to wait whenever any one of them hits a
hypervisor page fault.
This relaxes the policy, allowing the virtual core to run as soon as
any vcpu in it is runnable. With this, the KVMPPC_VCPU_STOPPED state
and the KVMPPC_VCPU_BUSY_IN_HOST state have been combined into a single
KVMPPC_VCPU_NOTREADY state, since we no longer need to distinguish
between them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a thread in a virtual core becomes runnable while other threads
in the same virtual core are already running in the guest, it is
possible for the latecomer to join the others on the core without
first pulling them all out of the guest. Currently this only happens
rarely, when a vcpu is first started. This fixes some bugs and
omissions in the code in this case.
First, we need to check for VPA updates for the latecomer and make
a DTL entry for it. Secondly, if it comes along while the master
vcpu is doing a VPA update, we don't need to do anything since the
master will pick it up in kvmppc_run_core. To handle this correctly
we introduce a new vcore state, VCORE_STARTING. Thirdly, there is
a race because we currently clear the hardware thread's hwthread_req
before waiting to see it get to nap. A latecomer thread could have
its hwthread_req cleared before it gets to test it, and therefore
never increment the nap_count, leading to messages about wait_for_nap
timeouts.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There were a few places where we were traversing the list of runnable
threads in a virtual core, i.e. vc->runnable_threads, without holding
the vcore spinlock. This extends the places where we hold the vcore
spinlock to cover everywhere that we traverse that list.
Since we possibly need to sleep inside kvmppc_book3s_hv_page_fault,
this moves the call of it from kvmppc_handle_exit out to
kvmppc_vcpu_run, where we don't hold the vcore lock.
In kvmppc_vcore_blocked, we don't actually need to check whether
all vcpus are ceded and don't have any pending exceptions, since the
caller has already done that. The caller (kvmppc_run_vcpu) wasn't
actually checking for pending exceptions, so we add that.
The change of if to while in kvmppc_run_vcpu is to make sure that we
never call kvmppc_remove_runnable() when the vcore state is RUNNING or
EXITING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Subsequent patches implementing in-kernel XICS emulation will make it
possible for IPIs to arrive at secondary threads at arbitrary times.
This fixes some races in how we start the secondary threads, which
if not fixed could lead to occasional crashes of the host kernel.
This makes sure that (a) we have grabbed all the secondary threads,
and verified that they are no longer in the kernel, before we start
any thread, (b) that the secondary thread loads its vcpu pointer
after clearing the IPI that woke it up (so we don't miss a wakeup),
and (c) that the secondary thread clears its vcpu pointer before
incrementing the nap count. It also removes unnecessary setting
of the vcpu and vcore pointers in the paca in kvmppc_core_vcpu_load.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a Book3S HV KVM guest is running, we need the host to be in
single-thread mode, that is, all of the cores (or at least all of
the cores where the KVM guest could run) to be running only one
active hardware thread. This is because of the hardware restriction
in POWER processors that all of the hardware threads in the core
must be in the same logical partition. Complying with this restriction
is much easier if, from the host kernel's point of view, only one
hardware thread is active.
This adds two hooks in the SMP hotplug code to allow the KVM code to
make sure that secondary threads (i.e. hardware threads other than
thread 0) cannot come online while any KVM guest exists. The KVM
code still has to check that any core where it runs a guest has the
secondary threads offline, but having done that check it can now be
sure that they will not come online while the guest is running.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
arch/powerpc/include/asm/Kbuild
arch/powerpc/include/asm/kvm_para.h
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PAPR paravirtualization interface lets guests register three
different types of per-vCPU buffer areas in its memory for communication
with the hypervisor. These are called virtual processor areas (VPAs).
Currently the hypercalls to register and unregister VPAs are handled
by KVM in the kernel, and userspace has no way to know about or save
and restore these registrations across a migration.
This adds "register" codes for these three areas that userspace can
use with the KVM_GET/SET_ONE_REG ioctls to see what addresses have
been registered, and to register or unregister them. This will be
needed for guest hibernation and migration, and is also needed so
that userspace can unregister them on reset (otherwise we corrupt
guest memory after reboot by writing to the VPAs registered by the
previous kernel).
The "register" for the VPA is a 64-bit value containing the address,
since the length of the VPA is fixed. The "registers" for the SLB
shadow buffer and dispatch trace log (DTL) are 128 bits long,
consisting of the guest physical address in the high (first) 64 bits
and the length in the low 64 bits.
This also fixes a bug where we were calling init_vpa unconditionally,
leading to an oops when unregistering the VPA.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set all the guest floating-point
state using the KVM_[GS]ET_ONE_REG ioctls. The floating-point state
includes all of the traditional floating-point registers and the
FPSCR (floating point status/control register), all the VMX/Altivec
vector registers and the VSCR (vector status/control register), and
on POWER7, the vector-scalar registers (note that each FP register
is the high-order half of the corresponding VSR).
Most of these are implemented in common Book 3S code, except for VSX
on POWER7. Because HV and PR differ in how they store the FP and VSX
registers on POWER7, the code for these cases is not common. On POWER7,
the FP registers are the upper halves of the VSX registers vsr0 - vsr31.
PR KVM stores vsr0 - vsr31 in two halves, with the upper halves in the
arch.fpr[] array and the lower halves in the arch.vsr[] array, whereas
HV KVM on POWER7 stores the whole VSX register in arch.vsr[].
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix whitespace, vsx compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
This enables userspace to get and set various SPRs (special-purpose
registers) using the KVM_[GS]ET_ONE_REG ioctls. With this, userspace
can get and set all the SPRs that are part of the guest state, either
through the KVM_[GS]ET_REGS ioctls, the KVM_[GS]ET_SREGS ioctls, or
the KVM_[GS]ET_ONE_REG ioctls.
The SPRs that are added here are:
- DABR: Data address breakpoint register
- DSCR: Data stream control register
- PURR: Processor utilization of resources register
- SPURR: Scaled PURR
- DAR: Data address register
- DSISR: Data storage interrupt status register
- AMR: Authority mask register
- UAMOR: User authority mask override register
- MMCR0, MMCR1, MMCRA: Performance monitor unit control registers
- PMC1..PMC8: Performance monitor unit counter registers
In order to reduce code duplication between PR and HV KVM code, this
moves the kvm_vcpu_ioctl_[gs]et_one_reg functions into book3s.c and
centralizes the copying between user and kernel space there. The
registers that are handled differently between PR and HV, and those
that exist only in one flavor, are handled in kvmppc_[gs]et_one_reg()
functions that are specific to each flavor.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: minimal style fixes]
Signed-off-by: Alexander Graf <agraf@suse.de>
When making a vcpu non-runnable we incorrectly changed the
thread IDs of all other threads on the core, just remove that
code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds an implementation of kvm_arch_flush_shadow_memslot for
Book3S HV, and arranges for kvmppc_core_commit_memory_region to
flush the dirty log when modifying an existing slot. With this,
we can handle deletion and modification of memory slots.
kvm_arch_flush_shadow_memslot calls kvmppc_core_flush_memslot, which
on Book3S HV now traverses the reverse map chains to remove any HPT
(hashed page table) entries referring to pages in the memslot. This
gets called by generic code whenever deleting a memslot or changing
the guest physical address for a memslot.
We flush the dirty log in kvmppc_core_commit_memory_region for
consistency with what x86 does. We only need to flush when an
existing memslot is being modified, because for a new memslot the
rmap array (which stores the dirty bits) is all zero, meaning that
every page is considered clean already, and when deleting a memslot
we obviously don't care about the dirty bits any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have an architecture-specific field in the kvm_memory_slot
structure, we can use it to store the array of page physical addresses
that we need for Book3S HV KVM on PPC970 processors. This reduces the
size of struct kvm_arch for Book3S HV, and also reduces the size of
struct kvm_arch_memory_slot for other PPC KVM variants since the fields
in it are now only compiled in for Book3S HV.
This necessitates making the kvm_arch_create_memslot and
kvm_arch_free_memslot operations specific to each PPC KVM variant.
That in turn means that we now don't allocate the rmap arrays on
Book3S PR and Book E.
Since we now unpin pages and free the slot_phys array in
kvmppc_core_free_memslot, we no longer need to do it in
kvmppc_core_destroy_vm, since the generic code takes care to free
all the memslots when destroying a VM.
We now need the new memslot to be passed in to
kvmppc_core_prepare_memory_region, since we need to initialize its
arch.slot_phys member on Book3S HV.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The generic KVM code uses SRCU (sleeping RCU) to protect accesses
to the memslots data structures against updates due to userspace
adding, modifying or removing memory slots. We need to do that too,
both to avoid accessing stale copies of the memslots and to avoid
lockdep warnings. This therefore adds srcu_read_lock/unlock pairs
around code that accesses and uses memslots.
Since the real-mode handlers for H_ENTER, H_REMOVE and H_BULK_REMOVE
need to access the memslots, and we don't want to call the SRCU code
in real mode (since we have no assurance that it would only access
the linear mapping), we hold the SRCU read lock for the VM while
in the guest. This does mean that adding or removing memory slots
while some vcpus are executing in the guest will block for up to
two jiffies. This tradeoff is acceptable since adding/removing
memory slots only happens rarely, while H_ENTER/H_REMOVE/H_BULK_REMOVE
are performance-critical hot paths.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pECD
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"Highlights include
- full big real mode emulation on pre-Westmere Intel hosts (can be
disabled with emulate_invalid_guest_state=0)
- relatively small ppc and s390 updates
- PCID/INVPCID support in guests
- EOI avoidance; 3.6 guests should perform better on 3.6 hosts on
interrupt intensive workloads)
- Lockless write faults during live migration
- EPT accessed/dirty bits support for new Intel processors"
Fix up conflicts in:
- Documentation/virtual/kvm/api.txt:
Stupid subchapter numbering, added next to each other.
- arch/powerpc/kvm/booke_interrupts.S:
PPC asm changes clashing with the KVM fixes
- arch/s390/include/asm/sigp.h, arch/s390/kvm/sigp.c:
Duplicated commits through the kvm tree and the s390 tree, with
subsequent edits in the KVM tree.
* tag 'kvm-3.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (93 commits)
KVM: fix race with level interrupts
x86, hyper: fix build with !CONFIG_KVM_GUEST
Revert "apic: fix kvm build on UP without IOAPIC"
KVM guest: switch to apic_set_eoi_write, apic_write
apic: add apic_set_eoi_write for PV use
KVM: VMX: Implement PCID/INVPCID for guests with EPT
KVM: Add x86_hyper_kvm to complete detect_hypervisor_platform check
KVM: PPC: Critical interrupt emulation support
KVM: PPC: e500mc: Fix tlbilx emulation for 64-bit guests
KVM: PPC64: booke: Set interrupt computation mode for 64-bit host
KVM: PPC: bookehv: Add ESR flag to Data Storage Interrupt
KVM: PPC: bookehv64: Add support for std/ld emulation.
booke: Added crit/mc exception handler for e500v2
booke/bookehv: Add host crit-watchdog exception support
KVM: MMU: document mmu-lock and fast page fault
KVM: MMU: fix kvm_mmu_pagetable_walk tracepoint
KVM: MMU: trace fast page fault
KVM: MMU: fast path of handling guest page fault
KVM: MMU: introduce SPTE_MMU_WRITEABLE bit
KVM: MMU: fold tlb flush judgement into mmu_spte_update
...
At the moment we call kvmppc_pin_guest_page() in kvmppc_update_vpa()
with two spinlocks held: the vcore lock and the vcpu->vpa_update_lock.
This is not good, since kvmppc_pin_guest_page() calls down_read() and
get_user_pages_fast(), both of which can sleep. This bug was introduced
in 2e25aa5f ("KVM: PPC: Book3S HV: Make virtual processor area
registration more robust").
This arranges to drop those spinlocks before calling
kvmppc_pin_guest_page() and re-take them afterwards. Dropping the
vcore lock in kvmppc_run_core() means we have to set the vcore_state
field to VCORE_RUNNING before we drop the lock, so that other vcpus
won't try to run this vcore.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds a new ioctl to enable userspace to control the size of the guest
hashed page table (HPT) and to clear it out when resetting the guest.
The KVM_PPC_ALLOCATE_HTAB ioctl is a VM ioctl and takes as its parameter
a pointer to a u32 containing the desired order of the HPT (log base 2
of the size in bytes), which is updated on successful return to the
actual order of the HPT which was allocated.
There must be no vcpus running at the time of this ioctl. To enforce
this, we now keep a count of the number of vcpus running in
kvm->arch.vcpus_running.
If the ioctl is called when a HPT has already been allocated, we don't
reallocate the HPT but just clear it out. We first clear the
kvm->arch.rma_setup_done flag, which has two effects: (a) since we hold
the kvm->lock mutex, it will prevent any vcpus from starting to run until
we're done, and (b) it means that the first vcpu to run after we're done
will re-establish the VRMA if necessary.
If userspace doesn't call this ioctl before running the first vcpu, the
kernel will allocate a default-sized HPT at that point. We do it then
rather than when creating the VM, as the code did previously, so that
userspace has a chance to do the ioctl if it wants.
When allocating the HPT, we can allocate either from the kernel page
allocator, or from the preallocated pool. If userspace is asking for
a different size from the preallocated HPTs, we first try to allocate
using the kernel page allocator. Then we try to allocate from the
preallocated pool, and then if that fails, we try allocating decreasing
sizes from the kernel page allocator, down to the minimum size allowed
(256kB). Note that the kernel page allocator limits allocations to
1 << CONFIG_FORCE_MAX_ZONEORDER pages, which by default corresponds to
16MB (on 64-bit powerpc, at least).
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix module compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
The H_REGISTER_VPA hcall implementation in HV Power KVM needs to pin some
guest memory pages into host memory so that they can be safely accessed
from usermode. It does this used get_user_pages_fast(). When the VPA is
unregistered, or the VCPUs are cleaned up, these pages are released using
put_page().
However, the get_user_pages() is invoked on the specific memory are of the
VPA which could lie within hugepages. In case the pinned page is huge,
we explicitly find the head page of the compound page before calling
put_page() on it.
At least with the latest kernel, this is not correct. put_page() already
handles finding the correct head page of a compound, and also deals with
various counts on the individual tail page which are important for
transparent huge pages. We don't support transparent hugepages on Power,
but even so, bypassing this count maintenance can lead (when the VM ends)
to a hugepage being released back to the pool with a non-zero mapcount on
one of the tail pages. This can then lead to a bad_page() when the page
is released from the hugepage pool.
This removes the explicit compound_head() call to correct this bug.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
When reading and writing SPRs, every SPR emulation piece had to read
or write the respective GPR the value was read from or stored in itself.
This approach is pretty prone to failure. What if we accidentally
implement mfspr emulation where we just do "break" and nothing else?
Suddenly we would get a random value in the return register - which is
always a bad idea.
So let's consolidate the generic code paths and only give the core
specific SPR handling code readily made variables to read/write from/to.
Functionally, this patch doesn't change anything, but it increases the
readability of the code and makes is less prone to bugs.
Signed-off-by: Alexander Graf <agraf@suse.de>
This is necessary for qemu to be able to pass the right information
to the guest, such as the supported page sizes and corresponding
encodings in the SLB and hash table, which can vary depending
on the processor type, the type of KVM used (PR vs HV) and the
version of KVM
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: fix compilation on hv, adjust for newer ioctl numbers]
Signed-off-by: Alexander Graf <agraf@suse.de>
There is nothing in the code for emulating TCE tables in the kernel
that prevents it from working on "PR" KVM... other than ifdef's and
location of the code.
This and moves the bulk of the code there to a new file called
book3s_64_vio.c.
This speeds things up a bit on my G5.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[agraf: fix for hv kvm, 32bit, whitespace]
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds code to measure "stolen" time per virtual core in units of
timebase ticks, and to report the stolen time to the guest using the
dispatch trace log (DTL). The guest can register an area of memory
for the DTL for a given vcpu. The DTL is a ring buffer where KVM
fills in one entry every time it enters the guest for that vcpu.
Stolen time is measured as time when the virtual core is not running,
either because the vcore is not runnable (e.g. some of its vcpus are
executing elsewhere in the kernel or in userspace), or when the vcpu
thread that is running the vcore is preempted. This includes time
when all the vcpus are idle (i.e. have executed the H_CEDE hypercall),
which is OK because the guest accounts stolen time while idle as idle
time.
Each vcpu keeps a record of how much stolen time has been reported to
the guest for that vcpu so far. When we are about to enter the guest,
we create a new DTL entry (if the guest vcpu has a DTL) and report the
difference between total stolen time for the vcore and stolen time
reported so far for the vcpu as the "enqueue to dispatch" time in the
DTL entry.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
The PAPR API allows three sorts of per-virtual-processor areas to be
registered (VPA, SLB shadow buffer, and dispatch trace log), and
furthermore, these can be registered and unregistered for another
virtual CPU. Currently we just update the vcpu fields pointing to
these areas at the time of registration or unregistration. If this
is done on another vcpu, there is the possibility that the target vcpu
is using those fields at the time and could end up using a bogus
pointer and corrupting memory.
This fixes the race by making the target cpu itself do the update, so
we can be sure that the update happens at a time when the fields
aren't being used. Each area now has a struct kvmppc_vpa which is
used to manage these updates. There is also a spinlock which protects
access to all of the kvmppc_vpa structs, other than to the pinned_addr
fields. (We could have just taken the spinlock when using the vpa,
slb_shadow or dtl fields, but that would mean taking the spinlock on
every guest entry and exit.)
This also changes 'struct dtl' (which was undefined) to 'struct dtl_entry',
which is what the rest of the kernel uses.
Thanks to Michael Ellerman <michael@ellerman.id.au> for pointing out
the need to initialize vcpu->arch.vpa_update_lock.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently on POWER7, if we are running the guest on a core and we don't
need all the hardware threads, we do nothing to ensure that the unused
threads aren't executing in the kernel (other than checking that they
are offline). We just assume they're napping and we don't do anything
to stop them trying to enter the kernel while the guest is running.
This means that a stray IPI can wake up the hardware thread and it will
then try to enter the kernel, but since the core is in guest context,
it will execute code from the guest in hypervisor mode once it turns the
MMU on, which tends to lead to crashes or hangs in the host.
This fixes the problem by adding two new one-byte flags in the
kvmppc_host_state structure in the PACA which are used to interlock
between the primary thread and the unused secondary threads when entering
the guest. With these flags, the primary thread can ensure that the
unused secondaries are not already in kernel mode (i.e. handling a stray
IPI) and then indicate that they should not try to enter the kernel
if they do get woken for any reason. Instead they will go into KVM code,
find that there is no vcpu to run, acknowledge and clear the IPI and go
back to nap mode.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for PowerPC.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: linuxppc-dev@lists.ozlabs.org
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have code to allocate big chunks of linear memory on bootup for later use.
This code is currently used for RMA allocation, but can be useful beyond that
extent.
Make it generic so we can reuse it for other stuff later.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This moves the get/set_one_reg implementation down from powerpc.c into
booke.c, book3s_pr.c and book3s_hv.c. This avoids #ifdefs in C code,
but more importantly, it fixes a bug on Book3s HV where we were
accessing beyond the end of the kvm_vcpu struct (via the to_book3s()
macro) and corrupting memory, causing random crashes and file corruption.
On Book3s HV we only accept setting the HIOR to zero, since the guest
runs in supervisor mode and its vectors are never offset from zero.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf update to apply on top of changed ONE_REG patches]
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently the code kzalloc()s new VCPUs instead of using the kmem_cache
which is created when KVM is initialized.
Modify it to allocate VCPUs from that kmem_cache.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This changes the implementation of kvm_vm_ioctl_get_dirty_log() for
Book3s HV guests to use the hardware C (changed) bits in the guest
hashed page table. Since this makes the implementation quite different
from the Book3s PR case, this moves the existing implementation from
book3s.c to book3s_pr.c and creates a new implementation in book3s_hv.c.
That implementation calls kvmppc_hv_get_dirty_log() to do the actual
work by calling kvm_test_clear_dirty on each page. It iterates over
the HPTEs, clearing the C bit if set, and returns 1 if any C bit was
set (including the saved C bit in the rmap entry).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds the infrastructure to enable us to page out pages underneath
a Book3S HV guest, on processors that support virtualized partition
memory, that is, POWER7. Instead of pinning all the guest's pages,
we now look in the host userspace Linux page tables to find the
mapping for a given guest page. Then, if the userspace Linux PTE
gets invalidated, kvm_unmap_hva() gets called for that address, and
we replace all the guest HPTEs that refer to that page with absent
HPTEs, i.e. ones with the valid bit clear and the HPTE_V_ABSENT bit
set, which will cause an HDSI when the guest tries to access them.
Finally, the page fault handler is extended to reinstantiate the
guest HPTE when the guest tries to access a page which has been paged
out.
Since we can't intercept the guest DSI and ISI interrupts on PPC970,
we still have to pin all the guest pages on PPC970. We have a new flag,
kvm->arch.using_mmu_notifiers, that indicates whether we can page
guest pages out. If it is not set, the MMU notifier callbacks do
nothing and everything operates as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This provides the low-level support for MMIO emulation in Book3S HV
guests. When the guest tries to map a page which is not covered by
any memslot, that page is taken to be an MMIO emulation page. Instead
of inserting a valid HPTE, we insert an HPTE that has the valid bit
clear but another hypervisor software-use bit set, which we call
HPTE_V_ABSENT, to indicate that this is an absent page. An
absent page is treated much like a valid page as far as guest hcalls
(H_ENTER, H_REMOVE, H_READ etc.) are concerned, except of course that
an absent HPTE doesn't need to be invalidated with tlbie since it
was never valid as far as the hardware is concerned.
When the guest accesses a page for which there is an absent HPTE, it
will take a hypervisor data storage interrupt (HDSI) since we now set
the VPM1 bit in the LPCR. Our HDSI handler for HPTE-not-present faults
looks up the hash table and if it finds an absent HPTE mapping the
requested virtual address, will switch to kernel mode and handle the
fault in kvmppc_book3s_hv_page_fault(), which at present just calls
kvmppc_hv_emulate_mmio() to set up the MMIO emulation.
This is based on an earlier patch by Benjamin Herrenschmidt, but since
heavily reworked.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This relaxes the requirement that the guest memory be provided as
16MB huge pages, allowing it to be provided as normal memory, i.e.
in pages of PAGE_SIZE bytes (4k or 64k). To allow this, we index
the kvm->arch.slot_phys[] arrays with a small page index, even if
huge pages are being used, and use the low-order 5 bits of each
entry to store the order of the enclosing page with respect to
normal pages, i.e. log_2(enclosing_page_size / PAGE_SIZE).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This removes the code from kvmppc_core_prepare_memory_region() that
looked up the VMA for the region being added and called hva_to_page
to get the pfns for the memory. We have no guarantee that there will
be anything mapped there at the time of the KVM_SET_USER_MEMORY_REGION
ioctl call; userspace can do that ioctl and then map memory into the
region later.
Instead we defer looking up the pfn for each memory page until it is
needed, which generally means when the guest does an H_ENTER hcall on
the page. Since we can't call get_user_pages in real mode, if we don't
already have the pfn for the page, kvmppc_h_enter() will return
H_TOO_HARD and we then call kvmppc_virtmode_h_enter() once we get back
to kernel context. That calls kvmppc_get_guest_page() to get the pfn
for the page, and then calls back to kvmppc_h_enter() to redo the HPTE
insertion.
When the first vcpu starts executing, we need to have the RMO or VRMA
region mapped so that the guest's real mode accesses will work. Thus
we now have a check in kvmppc_vcpu_run() to see if the RMO/VRMA is set
up and if not, call kvmppc_hv_setup_rma(). It checks if the memslot
starting at guest physical 0 now has RMO memory mapped there; if so it
sets it up for the guest, otherwise on POWER7 it sets up the VRMA.
The function that does that, kvmppc_map_vrma, is now a bit simpler,
as it calls kvmppc_virtmode_h_enter instead of creating the HPTE itself.
Since we are now potentially updating entries in the slot_phys[]
arrays from multiple vcpu threads, we now have a spinlock protecting
those updates to ensure that we don't lose track of any references
to pages.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This adds two new functions, kvmppc_pin_guest_page() and
kvmppc_unpin_guest_page(), and uses them to pin the guest pages where
the guest has registered areas of memory for the hypervisor to update,
(i.e. the per-cpu virtual processor areas, SLB shadow buffers and
dispatch trace logs) and then unpin them when they are no longer
required.
Although it is not strictly necessary to pin the pages at this point,
since all guest pages are already pinned, later commits in this series
will mean that guest pages aren't all pinned.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allocates an array for each memory slot that is added to store
the physical addresses of the pages in the slot. This array is
vmalloc'd and accessed in kvmppc_h_enter using real_vmalloc_addr().
This allows us to remove the ram_pginfo field from the kvm_arch
struct, and removes the 64GB guest RAM limit that we had.
We use the low-order bits of the array entries to store a flag
indicating that we have done get_page on the corresponding page,
and therefore need to call put_page when we are finished with the
page. Currently this is set for all pages except those in our
special RMO regions.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function should be called with interrupts disabled, to avoid
a race where an exception is delivered after we check, but the
resched kick is received before we disable interrupts (and thus doesn't
actually trigger the exit code that would recheck exceptions).
booke already does this properly in the lightweight exit case, but
not on initial entry.
For now, move the call of prepare_to_enter into subarch-specific code so
that booke can do the right thing here. Ideally book3s would do the same
thing, but I'm having a hard time seeing where it does any interrupt
disabling of this sort (plus it has several additional call sites), so
I'm deferring the book3s fix to someone more familiar with that code.
book3s behavior should be unchanged by this patch.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function also updates paravirt int_pending, so rename it
to be more obvious that this is a collection of checks run prior
to (re)entering a guest.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
arch/powerpc/kvm/book3s_hv.c: included 'linux/sched.h' twice,
remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently kvmppc_start_thread() tries to wake other SMT threads via
xics_wake_cpu(). Unfortunately xics_wake_cpu only exists when
CONFIG_SMP=Y so when compiling with CONFIG_SMP=N we get:
arch/powerpc/kvm/built-in.o: In function `.kvmppc_start_thread':
book3s_hv.c:(.text+0xa1e0): undefined reference to `.xics_wake_cpu'
The following should be fine since kvmppc_start_thread() shouldn't
called to start non-zero threads when SMP=N since threads_per_core=1.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If you build with KVM and UP it fails with the following due to a
missing include.
/arch/powerpc/kvm/book3s_hv.c: In function 'do_h_register_vpa':
arch/powerpc/kvm/book3s_hv.c:156:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:156:10: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/kvm/book3s_hv.c:192:12: error: 'H_RESOURCE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:222:9: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c: In function 'kvmppc_pseries_do_hcall':
arch/powerpc/kvm/book3s_hv.c:228:30: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:232:7: error: 'H_CEDE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:234:7: error: 'H_PROD' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:238:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:250:7: error: 'H_CONFER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:252:7: error: 'H_REGISTER_VPA' undeclared (first use in this function)
make[2]: *** [arch/powerpc/kvm/book3s_hv.o] Error 1
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org (3.1 only)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With a KVM guest operating in SMT4 mode (i.e. 4 hardware threads per
core), whenever a CPU goes idle, we have to pull all the other
hardware threads in the core out of the guest, because the H_CEDE
hcall is handled in the kernel. This is inefficient.
This adds code to book3s_hv_rmhandlers.S to handle the H_CEDE hcall
in real mode. When a guest vcpu does an H_CEDE hcall, we now only
exit to the kernel if all the other vcpus in the same core are also
idle. Otherwise we mark this vcpu as napping, save state that could
be lost in nap mode (mainly GPRs and FPRs), and execute the nap
instruction. When the thread wakes up, because of a decrementer or
external interrupt, we come back in at kvm_start_guest (from the
system reset interrupt vector), find the `napping' flag set in the
paca, and go to the resume path.
This has some other ramifications. First, when starting a core, we
now start all the threads, both those that are immediately runnable and
those that are idle. This is so that we don't have to pull all the
threads out of the guest when an idle thread gets a decrementer interrupt
and wants to start running. In fact the idle threads will all start
with the H_CEDE hcall returning; being idle they will just do another
H_CEDE immediately and go to nap mode.
This required some changes to kvmppc_run_core() and kvmppc_run_vcpu().
These functions have been restructured to make them simpler and clearer.
We introduce a level of indirection in the wait queue that gets woken
when external and decrementer interrupts get generated for a vcpu, so
that we can have the 4 vcpus in a vcore using the same wait queue.
We need this because the 4 vcpus are being handled by one thread.
Secondly, when we need to exit from the guest to the kernel, we now
have to generate an IPI for any napping threads, because an HDEC
interrupt doesn't wake up a napping thread.
Thirdly, we now need to be able to handle virtual external interrupts
and decrementer interrupts becoming pending while a thread is napping,
and deliver those interrupts to the guest when the thread wakes.
This is done in kvmppc_cede_reentry, just before fast_guest_return.
Finally, since we are not using the generic kvm_vcpu_block for book3s_hv,
and hence not calling kvm_arch_vcpu_runnable, we can remove the #ifdef
from kvm_arch_vcpu_runnable.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are multiple features in PowerPC KVM that can now be enabled
depending on the user's wishes. Some of the combinations don't make
sense or don't work though.
So this patch adds a way to check if the executing environment would
actually be able to run the guest properly. It also adds sanity
checks if PVR is set (should always be true given the current code
flow), if PAPR is only used with book3s_64 where it works and that
HV KVM is only used in PAPR mode.
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for running KVM guests in supervisor mode on those
PPC970 processors that have a usable hypervisor mode. Unfortunately,
Apple G5 machines have supervisor mode disabled (MSR[HV] is forced to
1), but the YDL PowerStation does have a usable hypervisor mode.
There are several differences between the PPC970 and POWER7 in how
guests are managed. These differences are accommodated using the
CPU_FTR_ARCH_201 (PPC970) and CPU_FTR_ARCH_206 (POWER7) CPU feature
bits. Notably, on PPC970:
* The LPCR, LPID or RMOR registers don't exist, and the functions of
those registers are provided by bits in HID4 and one bit in HID0.
* External interrupts can be directed to the hypervisor, but unlike
POWER7 they are masked by MSR[EE] in non-hypervisor modes and use
SRR0/1 not HSRR0/1.
* There is no virtual RMA (VRMA) mode; the guest must use an RMO
(real mode offset) area.
* The TLB entries are not tagged with the LPID, so it is necessary to
flush the whole TLB on partition switch. Furthermore, when switching
partitions we have to ensure that no other CPU is executing the tlbie
or tlbsync instructions in either the old or the new partition,
otherwise undefined behaviour can occur.
* The PMU has 8 counters (PMC registers) rather than 6.
* The DSCR, PURR, SPURR, AMR, AMOR, UAMOR registers don't exist.
* The SLB has 64 entries rather than 32.
* There is no mediated external interrupt facility, so if we switch to
a guest that has a virtual external interrupt pending but the guest
has MSR[EE] = 0, we have to arrange to have an interrupt pending for
it so that we can get control back once it re-enables interrupts. We
do that by sending ourselves an IPI with smp_send_reschedule after
hard-disabling interrupts.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>