The example in audio-graph-card2.c has multiple nodes with the same name
in it. Change the port numbers to get different names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220624092601.2445224-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Because Sound Card needs many drivers to probe, current audio-graph-card2
will indicate "Experimental stage" at top of probe function even though
in case it gets -EPROBE_DEFER, thus it will be indicated many times.
This patch indicates it when probe was succeeded.
[ 1.601393] asoc-audio-graph-card2 sound: Audio Graph Card2 is still under Experimental stage
...
[ 1.721269] asoc-audio-graph-card2 sound: Audio Graph Card2 is still under Experimental stage
...
[ 1.755231] asoc-audio-graph-card2 sound: Audio Graph Card2 is still under Experimental stage
...
[ 1.907710] asoc-audio-graph-card2 sound: Audio Graph Card2 is still under Experimental stage
...
[ 1.933173] rcar_sound ec500000.sound: probed
[ 1.948875] asoc-audio-graph-card2 sound: Audio Graph Card2 is still under Experimental stage
[ 1.959558] asoc-audio-graph-card2 sound: ak4613-hifi <-> rsnd-dai.0 mapping ok
[ 1.968119] asoc-audio-graph-card2 sound: i2s-hifi <-> rsnd-dai.1 mapping ok
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o80vgn5a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some audio hardware cannot support the same slot width for all sample
widths, or a slot width equal to the sample width for all sample widths.
This is usually due either to limitations of the audio serial port or
system clocking restrictions.
A typical example would be:
- 16-bit samples in 16-bit slots
- 24-bit samples in 32-bit slots
The new dai-tdm-slot-width-map property allows setting a mapping of
sample widths and the corresponding tdm slot widths and slot counts.
Although the slot count is usually the same for all cases this does
allow for adding padding slots to maintain the same bitclk frequency.
The property is added to each endpoint node that needs the component
DAI to be told the TDM slot width and count.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220228172754.453783-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec support to audio-graph-card2.
It can use Codec2Codec but very simple case only for now.
It doesn't have "SWITCH" control yet, thus it start automatically
when it was probed, and can't stop, so far.
Thus it needs to be updated around widgets/routing handling,
and you need to understand that it is under experimental.
Codec has SND_SOC_DAPM_INPUT() (= IN) / SND_SOC_DAPM_OUTPUT(= OUT)
widgets in below case.
It is assuming 2channel, S32_LE format for now.
It needs to be updated, too.
It needs "codec2codec" node (= B), needs to have routing (= A),
need to indicate CPU side at links (= X).
ports@0 is for CPU side (= X), port@1 is Codec side (= Y).
It needs to have "rate" (= C)
+--+
| |<-- Codec0 <-- IN
| |--> Codec1 --> OUT
+--+
sound {
compatible = "audio-graph-card2";
(A) routing = "OUT" ,"DAI1 Playback",
"DAI0 Capture", "IN";
(X) links = <&c2c>;
(B) codec2codec {
ports {
(C) rate = <48000>;
(X) c2c: port@0 { c2cf_ep: endpoint { remote-endpoint = <&codec0_ep>; }; };
(Y) port@1 { c2cb_ep: endpoint { remote-endpoint = <&codec1_ep>; }; };
};
};
Codec {
ports {
port@0 {
bitclock-master;
frame-master;
codec0_ep: endpoint { remote-endpoint = <&c2cf_ep>; }; };
port@1 { codec1_ep: endpoint { remote-endpoint = <&c2cb_ep>; }; };
};
};
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y26ylu4a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
