Check NodeID.nodeNumber as per OHCI 1.1 clause 7.2.3.2. See also IEEE
1394a table 5B-1.
Also, demote the "node ID not valid" message from error to notification
as it is not an error condition.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
at_context_queue_packet() didn't clean up in an early exit path.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
It seems unlikely, but access to self_id_cpu[0] could at least in theory
be deferred until after the loop over self_id_cpu[1..n] or even after
the subsequent reg_read. Enforce the desired order by a read barrier.
Also prevent the reg_read from being reordered relative to the for loop.
This isn't necessary if the loop's conditional printk counts as an
implicit barrier, but better make it explicit.
(self_id_cpu[] is a coherent DMA buffer.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Firewire-sbp2 did very uncooperative things in the kernel's shared
workqueue: Sleeping until reception of management status from the
target for up to 2 seconds, and performing SCSI inquiry and all of the
setup of SCSI command set drivers via scsi_add_device. If there were
transient or permanent error conditions, this caused long blockage of
the kernel's events process, noticeable e.g. by blocked keyboard input.
We now allocate a workqueue process exclusive to fw-sbp2. As a side
effect, this also increases parallelism of fw-sbp2's login and reconnect
work versus fw-core's device discovery and device update work which is
performed in the shared workqueue.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
On rare occasions, the ability to set one of the workaround flags at
runtime may save the day.
People who experience I/O errors with firewire-sbp2 while the old sbp2
driver worked for them should try workarounds=1 and report to the devel
mailinglist whether that improves things. Firewire-sbp2 defaults to the
SCSI stack's maximum transfer size per command, while sbp2 limits them
to 128 kBytes. Flag 1 accomplishes just that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On IOMMU-less noncoherent architectures, orb->callback will memcpy the
whole SCSI command buffer for READ-like SCSI commands. It is therefore
friendlier to enable IRQs before the call, like before patch "Add
ref-counting for sbp2 orbs".
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Sparse warned about it although it was apparently harmless:
drivers/firewire/fw-cdev.c:624:23: warning: symbol 'interrupt' shadows an earlier one
include/asm/hw_irq.h:29:13: originally declared here
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
drivers/ieee1394/ieee1394_core.c: Define spinlock using
DEFINE_SPINLOCK instead of assignment to SPIN_LOCK_UNLOCKED
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
At least since nodemgr got rid of coarse global locking, accesses to
struct csr1212_keyval's reference counter should be atomic and coupled
with proper barriers. Also, calls to csr1212_keep_keyval(kv) should
occur before kv is being used.
(We probably should convert refcnt to struct kref, but how to keep
csr1212_destroy_keyval's implementation non-recursively then?)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
csr1212_keep_keyval(kv) in nodemgr_process_root_directory was
unbalanced if ne->vendor_name_kv already exists. This happens for
example if eth1394 or raw1394 modify the local config ROM and it is
parsed again.
As a bonus, the attempt to add the vendor_name_kv sysfs attribute
when it already exists is now fixed for good.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* Delete optional and empty i2c client_register and client_unregister
callbacks.
* Use the proper i2c adapter ID.
* Don't use a template to initialize the i2c_adapter structure, it's
inefficient.
* Update a misleading comment on why we use i2c_transfer rather than
higher level i2c functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The nodemgr host thread can exit on its own even when kthread_should_stop
is not true, on receiving a signal (might never happen in practice, as
it ignores signals). But considering kthread_stop() must not be mixed with
kthreads that can exit on their own, I think changing the code like this
is clearer. This change means the thread can cut its sleep short when
receive a signal but looking at the code around, that sounds okay (and
again, it might never actually recieve a signal in practice).
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
sbp2_host_reset and sbp2_handle_status_write are not serialized against
sbp2_alloc_device and sbp2_remove_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (264 commits)
[ALSA] version 1.0.15
[ALSA] Fix thinko in cs4231 mce down check
[ALSA] sun-cs4231: improved waiting after MCE down
[ALSA] sun-cs4231: use cs4231-regs.h
[ALSA] This simplifies and fixes waiting loops of the mce_down()
[ALSA] This patch adds support for a wavetable chip on
[ALSA] This patch removes open_mutex from the ad1848-lib as
[ALSA] fix bootup crash in snd_gus_interrupt()
[ALSA] hda-codec - Fix SKU ID function for realtek codecs
[ALSA] Support ASUS P701 eeepc [0x1043 0x82a1] support
[ALSA] hda-codec - Add array terminator for dmic in STAC codec
[ALSA] hdsp - Fix zero division
[ALSA] usb-audio - Fix double comment
[ALSA] hda-codec - Fix STAC922x volume knob control
[ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz
[ALSA] hda-codec - Fix for Fujitsu Lifebook C1410
[ALSA] mpu-401: remove MPU401_INFO_UART_ONLY flag
[ALSA] mpu-401: do not require an ACK byte for the ENTER_UART command
[ALSA] via82xx - Add DXS quirk for Shuttle AK31v2
[ALSA] hda-codec - Fix input_mux numbers for vaio stac92xx
...
- Previese patch to NCR5380 broke scsi_mac because
AUTOSENSE was defined after the inclusion of
NCR5380.h. Fix it
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a test in tgafb_mono_imageblit() for a colour image with a fall-back
to cfb_imageblit(). The test is not necessary as the only caller, which is
tgafb_imageblit(), checks it too and only invokes this function for monochrome
images. It looks like a left-over from before some changes to
tgafb_imageblit().
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pixel mask calculation in tgafb_mono_imageblit() uses a variable
left-shift on a 32-bit data type by up to 32. Shifting by the width of a data
type or more produces an unpredictable result according to the C standard.
Rather than widening the data type this fix makes sure the count is between 0
and 31. The reason is not to penalise 32-bit platforms with operation on a
"long long" type for a marginal case that is meant not to happen (blitting an
image of a zero width).
The reason it has escaped for so long is the Alpha, being purely 64-bit, :-)
does not mask the shift out to 32 bits. This is a valid implementation --
producing the correct result certainly falls within "unpredictable behaviour".
It does trigger on MIPS though and it is the recent merge of the TC support
which only enabled the driver for use on anything other than the Alpha. For
MIPS when the width is 32 the mask ends up being 0 rather than 0xffffffff as
it should be and the frame buffer is not updated.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Jay Estabrook <Jay.Estabrook@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported in Bugzilla Bug 9093, upon switching to X, a small rectangular
cursor can still be seen blinking in the upper left part of the screen. It is
fbcon's text cursor. This is caused by a strange ioctl(..., KDSETMODE,
KD_TEXT) call done by something in userspace, perhaps by X itself, while the
tty is still in graphics mode. And when the tty is in KD_TEXT mode, the
cursor timer is restarted.
Although this is a userspace problem, we can work around it by delaying the
restart of the cursor timer until an fbcon_switch() is called. In other
words, the cursor timer will not be restarted even if a KD_TEXT mode switch is
requested.
Regression potential: Present but low
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This correct case, when source and destination X coordinates difference is n
multiple of pixels in byte. This is probably rare case, but this case should
supported for completeness.
Reorganization of FB_READL and FB_WRITEL calls results in code size decrease
for normal build without swapping support and size with support enabled is
reasonable too.
[adaplas]
Add missing fb_rev_pixels_in_long() prototype.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds check if selected pixclock is valid (is in the PLL range).
Previously, if the pixclock could not be set, the new mode resolution was set
but pixclock was not set which led to incorrect timings sent to monitor.
[adaplas]
Fixed a few misplaced curly braces.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection matching algorithm. It allows to choose
mode with matching depth even when requested color lengths are greater than
color lengths of every mode with requested color depth.
It also fixes bug in s3fb - wrong error value returned when format is not
supported by chip.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Default to the 480p video mode on DVI-D and HDMI displays if `video=safe' is
passed on the kernel command line.
This is intended to be used by `kboot'-style boot loaders (i.e. first-stage
kernels) for the PS3, to provide a failsafe video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the extern declaration for global_mode_option to <linux/fb.h> and rename
the variable to fb_mode_option.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Enhance horizontal panning on firmware 1.90 and up:
- On firmware 1.90 and up, L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT supports copying
rectangles from XDR to DDR memory with different source and destination
line lengths. Hence larger horizontal virtual resolutions can be supported
(up to 16368 pixels).
- As the actual frame buffer memory layout no longer matches the entries in
ps3fb_res[], create fake struct ps3fb_ioctl_res data for the
PS3FB_IOCTL_SCREENINFO ioctl, so user space applications that depend on it
keep on working.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Add virtual screen and panning support:
- The vertical virtual screen size is limited by the amount of memory
reserved for ps3fb,
- The horizontal virtual screen size is limited to the fullscreen width,
- Advertise that we support panning, so fbcon will use it if the virtual
screen is enabled.
Enabling a virtual screen (using `fbset -vyres nnn') can speed up text
console scrolling by a factor of 10-15, depending on the video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't keep the borders for non-fullscreen modes in XDR memory:
- Extract ps3fb_sync_image()
- Work around the alignment restrictions of L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT
by using an offset with L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP
- Only copy the visible part of the screen on every vblank
- Always put the real frame buffer at the start of video memory
- Clear fullscreen DDR memory on mode change
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: Use fb_info.par properly:
o Move mode-specific fields into struct ps3fb_par
o Allocate struct ps3fb_par using framebuffer_alloc()
o Protect access to ps3fb_par in ps3fb_sync() using the console semaphore
(this semaphore is already held when ps3fb_set_par() is called)
o Avoid calling ps3av_set_video_mode() if the actual video mode hasn't
changed
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3fb: In the case of non-fullscreen video modes, there was a partial overlap
of the GPU command buffer and the frame buffer. Fix and cleanup various issues
with overlap and alignment:
- Move the GPU command buffer from the beginning to the end of video memory
- Exclude the GPU command buffer from the actual frame buffer memory
- Align the start of the virtual frame buffer to PAGE_SIZE instead of to 64
KiB, and don't waste memory if it's already aligned (for fullscreen modes)
- Take into account the alignment when checking memory requirements and
maximum number of frames
- Make sure fb_fix_screeninfo.smem_start always points to the virtual frame
buffer start, so we don't have to compensate for that in ps3fb_mmap()
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make ps3fb_wait_for_vsync() and ps3fb_flip_ctl() static, as they're no
(longer) used outside ps3fb.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up includes
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not print warnings on invalid frame numbers, as this can be triggered from
user space.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i.MX frame-buffer read operation should be faster for all configurations
then drawing each individual character again in response to scroll events.
The nonstandard fields allows to configure frame-buffer special options flags
for different display configurations by board specific initialization code.
One of such specific options is reversed order of pixels in each individual
byte. i.MX frame-buffer seems to be designed for big-endian use first. The
byte order is correctly configured for little-endian ordering, but if 1, 2 or
4 bits per pixel are used, pixels ordering is incompatible to Linux generic
frame-buffer drawing functions.
The patch "Allow generic BitBLT functions to work with swapped pixel order in
bytes" introduces required functionality into FBDEV core. The pixels ordering
selection has to be enabled at compile time CONFIG_FB_CFB_REV_PIXELS_IN_BYTE
and for each display configuration which requires it by flag
FB_NONSTD_REV_PIX_IN_B in "nonstd" field of info structure.
This patch provides way for board specific code to select this option.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
don't distinguish between `boot' and `non-boot' autodetection now the
autodetection code has been improved
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add a quirk database for broken monitors where the `best' advertised
video mode doesn't work
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
treat DVI-D monitors like HDMI monitors when autodetecting the best video mode
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't make much sense to use the PS3AV_CMD_VIDEO_VID_* values in the
autodetection code, just to convert them to PS3 video mode ids afterwards.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: eliminate PS3AV_DEBUG
- Move ps3av_cmd_av_monitor_info_dump from ps3av_cmd.c to ps3av.c, as
it's
used there only
- Integrate ps3av_cmd_av_hw_conf_dump() into its sole user
- Use pr_debug() for printing debug info
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
