Document the device tree binding for the WM8903 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the WM8903 is hooked up to an interrupt, set the irq_active_low flag
in the default platform data based on the IRQ's IRQ_TYPE. Map IRQ_TYPE_NONE
(a lack of explicit configuration/restriction) to irq_active_low = false;
the previous default.
This code is mainly added to support device tree interrupt bindings,
although will work perfectly well in a non device tree system too.
Any interrupt controller that supports only a single IRQ_TYPE could
set each IRQ's type based on that restriction. This applies equally
with and without device tree. To cater for interrupt controllers
that don't do this, for which irqd_get_trigger_type() will return
IRQ_TYPE_NONE, the platform data irq_active_low field may be used
in systems that don't use device tree.
With device tree, every IRQ must have some IRQ_TYPE set.
Controllers that support DT and multiple IRQ_TYPEs must define the
interrupts property (as used in interrupt source nodes) such that it
defines the IRQ_TYPE to use. When the core DT setup code initializes
wm8903->irq, the interrupts property will be parsed, and as a side-
effect, set the IRQ's IRQ_TYPE for the WM8903 probe() function to read.
Controllers that support DT and a single IRQ_TYPE could arrange to
set the IRQ_TYPE somehow during their initialization, or hard-code
it during the processing of the child interrupts property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pdata pointer is now always valid. Remove any conditions that check
its validity.
This patch is mostly just removing an indentation level. One variable had
to be moved due to the removal of a scope, and one comment was split into
two. Viewing the patch with git show/diff -b will show that it's actually
very small.
Note that WM8903_MIC_BIAS_CONTROL_0 is now written unconditionally,
whereas it used to be written only if pdata was supplied. Since
defpdata.micdet_cfg = 0, this unconditional write simply echos the HW
defaults in the case where pdata is not supplied.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_one can make the error handling simpler.
Also remove a redundant "Failed to issue reset" error message.
We already show the error message in uda1380_reset() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error for uda1380_modinit if i2c_add_driver() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When no platform data is supplied, point pdata at a default platform
structure. This enables two future changes:
a) Defines the default platform data values in a single place.
b) There is always a valid pdata pointer, so some conditional code can
be simplified by a later patch.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get control of the device earlier and avoid trying to do an ASoC probe
on a card that won't work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Converting to an rbtree cache as regcache doesn't have a flat cache.
Since the top of the register map is fairly sparse this should be an
overall win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
We only do this on initial power on so it's at best a waste of time as
the core will have already defaulted to the same values.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The driver used to use a complicated method to sync the register cache
after having brought the bias level up to standby in resume due to the
use of the write sequencer to manage the initial power up. Now that we
don't use the write sequencer there is no need for this and we can just
use snd_soc_cache_sync() directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Since they don't actually have power bits but do have events associated
with them it's important that we bootstrap their state properly which
making them virtual does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The GPIO registers are 15 bits wide. Hence values, higher than 0x7fff are
not legal GPIO register values. Modify the pdata.gpio_cfg handling code
to reject all illegal values, not just WM8903_GPIO_NO_CONFIG (0x8000). This
will allow the later use of 0xffffffff as an invalid value in future device
tree bindings, meaning "don't touch this GPIO's configuration".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Still have a manual free in there for some realloc()ed memory as there's
no devm version of that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to rerun DAPM if the clock source is the same but we do
need to adjust the microphone detection rate in case we are moving from
an audio to a non-audio rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Actively manage the detection rate for microphones with WM8958, providing
improved power consumption and maximising the benefit from the hardware
debounce.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we don't have any active audio we can put the microphone biases into
bypass mode to save power at the expense of performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure SYSCLK is enabled while running accessory detection on WM8958.
It is always required so there is no sense in requiring machine drivers
to individually do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for loading the SigmaDSP firmware using regmap. This allows us
to transparently use SPI or I2C as the transport protocol on devices which
support them.
For now we keep the old I2C support since we have one user of this which is not
straight forward to convert to regmap, due to variable length registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the structs and functions only used by SigmaDSP firmware loader itself
from the header to the C file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide some error messages when loading the firmware fails, so it is possible
to diagnose the reason for the failure.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want is to clear BIT[5:4](PCM_MODE_MASK) and BIT[3](PCM_BIT_ORDER) bits,
but current code clears BIT[2:0].
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can reduce the code size here a bit by using snd_soc_update_bits instead of
open-coding the read-modify-write cycle. The conversion done in this patch is
not completely straightforward and some minor code restructuring has been
incorporated to further reduce the code size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a DAPM supply widget for the internal sysclk, so it can be disabled
automatically when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM route controls only take effect on paths where the sink is a mixer or a
mux, furthermore the control must be a control assigned to the mixer or mux.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename it to MICBIAS to reflect the pin name and help any out of tree
users notice the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
It's never been updated so it can't be that useful and it makes the
driver needlessly chatty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With device tree support for regulators, its needed that the
regulator_dev->dev device has the right of_node attached.
To be able to do this add an additional parameter to the
regulator_register() api, wherein the dt-adapted driver can
then pass this additional info onto the regulator core.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 85e7652("ASoC: Constify snd_soc_dai_ops structs") accidentally
introduced a few duplicated consts. This patch cleans it up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just checking the code in cs42l51_fill_cache():
The cache pointer points to codec->reg_cache + 1.
I think it is because CS42L51_FIRSTREG is 0x01,
so codec->reg_cache[0] is not used here.
Then we read CS42L51_NUMREGS bytes to cache.
So we need reg_cache_size to be CS42L51_NUMREGS + 1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the manual register restore mechanism in cs4270.c and call the
generic snd_soc_cache_sync() handler instead.
This factors code out in favour of core facilities and also fixes a
bus confusion that is most probably caused by intermixing i2c-regmap
functions and i2c_smbus_* accessors.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of ((max9877_regs[reg] >> shift) & mask) != val
but ((max9877_regs[reg2] >> shift) & mask) == val2,
current code does not update the registers.
Fix the logic to update registers if either val or val2 is changed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
The BIT[5:4] of ADC Control Register 2 is to control the word width.
00 = 25 Bits
01 = 20 Bits
10 = 16 Bits
11 = Invalid
Thus, the AD1836_ADC_WORD_OFFSET should be defined as 4.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Fix below smatch warning:
sound/soc/codecs/cs42l73.c +1030 cs42l73_set_dai_fmt(53) error: inv is never equal to 1024 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1032 cs42l73_set_dai_fmt(55) error: inv is never equal to 768 (wrong type 0 - 255).
sound/soc/codecs/cs42l73.c +1036 cs42l73_set_dai_fmt(59) error: inv is never equal to 1024 (wrong type 0 - 255).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code defines some bits with left shift to the proper bit defined in
datasheet, but some don't.
Unify the definition with proper left shift and adjust the code accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver only supports I2C so doesn't need to do things conditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
They're all volatile so shouldn't have defaults and as we've got pages
into the DSP memory the registers themselves aren't that useful - a
further patch adding support for the DSPs will provide direct diagnostic
access to the DSP memories.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's done in cs42l73_set_bias_level when the dapm.bias_level is switching
from SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if device id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
the last entry from being omitted.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the array.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
There is no need to provide defaults for the volatile
registers and doing so might cause confusion.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch makes it possible to set DAI mode to its currently applied
value even if codec is active. This is necessary to allow
aplay -t raw -r 44100 -f S16_LE -c 2 < /dev/urandom &
alsactl store -f backup.state
alsactl restore -f backup.state
to work without returning errors. This patch is based on a patch sent
by Klaus Kurzmann <mok@fluxnetz.de>.
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
There are two undocumented registers in use in alc5632_i2c_probe
function. It must be added to support future rewrite of this
function to use regmap API completely.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Cirrus Logic CS42L73 low power stereo
codec.
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Georgi Vlaev <joe@nucleusys.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sta32x resets and loses all configuration during ESD test.
Work around by polling the CONFA register once a second
and restore all coeffcients and registers when CONFA
changes unexpectedly.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a structure for platform specific configuration and use it,
thereby removing a few FIXMEs which marked hard-coded values.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The coefficient RAM must be saved in a shadow so it can
be restored when the codec is powered on using
regulator_bulk_enable().
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Large code size increase due to the addition of readability information
and the reformatting of the defaults table.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get things configured as early as possible, especially useful for the
GPIOs which might be useful anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver implements basic functionality, using I²C for the control
channel.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
