From f58872f45c36ded048bccc22701b0986019c24d8 Mon Sep 17 00:00:00 2001 From: Marcelo Schmitt Date: Fri, 12 Jul 2024 16:20:36 -0300 Subject: [PATCH] spi: Enable controllers to extend the SPI protocol with MOSI idle configuration The behavior of an SPI controller data output line (SDO or MOSI or COPI (Controller Output Peripheral Input) for disambiguation) is usually not specified when the controller is not clocking out data on SCLK edges. However, there do exist SPI peripherals that require specific MOSI line state when data is not being clocked out of the controller. Conventional SPI controllers may set the MOSI line on SCLK edges then bring it low when no data is going out or leave the line the state of the last transfer bit. More elaborated controllers are capable to set the MOSI idle state according to different configurable levels and thus are more suitable for interfacing with demanding peripherals. Add SPI mode bits to allow peripherals to request explicit MOSI idle state when needed. When supporting a particular MOSI idle configuration, the data output line state is expected to remain at the configured level when the controller is not clocking out data. When a device that needs a specific MOSI idle state is identified, its driver should request the MOSI idle configuration by setting the proper SPI mode bit. Acked-by: Nuno Sa Reviewed-by: Jonathan Cameron Reviewed-by: David Lechner Tested-by: David Lechner Signed-off-by: Marcelo Schmitt Link: https://patch.msgid.link/9802160b5e5baed7f83ee43ac819cb757a19be55.1720810545.git.marcelo.schmitt@analog.com Signed-off-by: Mark Brown --- Documentation/spi/spi-summary.rst | 83 +++++++++++++++++++++++++++++++ drivers/spi/spi.c | 6 +++ include/uapi/linux/spi/spi.h | 5 +- 3 files changed, 92 insertions(+), 2 deletions(-) diff --git a/Documentation/spi/spi-summary.rst b/Documentation/spi/spi-summary.rst index 7f8accfae6f9..6e21e6f86912 100644 --- a/Documentation/spi/spi-summary.rst +++ b/Documentation/spi/spi-summary.rst @@ -614,6 +614,89 @@ queue, and then start some asynchronous transfer engine (unless it's already running). +Extensions to the SPI protocol +------------------------------ +The fact that SPI doesn't have a formal specification or standard permits chip +manufacturers to implement the SPI protocol in slightly different ways. In most +cases, SPI protocol implementations from different vendors are compatible among +each other. For example, in SPI mode 0 (CPOL=0, CPHA=0) the bus lines may behave +like the following: + +:: + + nCSx ___ ___ + \_________________________________________________________________/ + • • + • • + SCLK ___ ___ ___ ___ ___ ___ ___ ___ + _______/ \___/ \___/ \___/ \___/ \___/ \___/ \___/ \_____ + • : ; : ; : ; : ; : ; : ; : ; : ; • + • : ; : ; : ; : ; : ; : ; : ; : ; • + MOSI XXX__________ _______ _______ ________XXX + 0xA5 XXX__/ 1 \_0_____/ 1 \_0_______0_____/ 1 \_0_____/ 1 \_XXX + • ; ; ; ; ; ; ; ; • + • ; ; ; ; ; ; ; ; • + MISO XXX__________ _______________________ _______ XXX + 0xBA XXX__/ 1 \_____0_/ 1 1 1 \_____0__/ 1 \____0__XXX + +Legend:: + + • marks the start/end of transmission; + : marks when data is clocked into the peripheral; + ; marks when data is clocked into the controller; + X marks when line states are not specified. + +In some few cases, chips extend the SPI protocol by specifying line behaviors +that other SPI protocols don't (e.g. data line state for when CS is not +asserted). Those distinct SPI protocols, modes, and configurations are supported +by different SPI mode flags. + +MOSI idle state configuration +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Common SPI protocol implementations don't specify any state or behavior for the +MOSI line when the controller is not clocking out data. However, there do exist +peripherals that require specific MOSI line state when data is not being clocked +out. For example, if the peripheral expects the MOSI line to be high when the +controller is not clocking out data (``SPI_MOSI_IDLE_HIGH``), then a transfer in +SPI mode 0 would look like the following: + +:: + + nCSx ___ ___ + \_________________________________________________________________/ + • • + • • + SCLK ___ ___ ___ ___ ___ ___ ___ ___ + _______/ \___/ \___/ \___/ \___/ \___/ \___/ \___/ \_____ + • : ; : ; : ; : ; : ; : ; : ; : ; • + • : ; : ; : ; : ; : ; : ; : ; : ; • + MOSI _____ _______ _______ _______________ ___ + 0x56 \_0_____/ 1 \_0_____/ 1 \_0_____/ 1 1 \_0_____/ + • ; ; ; ; ; ; ; ; • + • ; ; ; ; ; ; ; ; • + MISO XXX__________ _______________________ _______ XXX + 0xBA XXX__/ 1 \_____0_/ 1 1 1 \_____0__/ 1 \____0__XXX + +Legend:: + + • marks the start/end of transmission; + : marks when data is clocked into the peripheral; + ; marks when data is clocked into the controller; + X marks when line states are not specified. + +In this extension to the usual SPI protocol, the MOSI line state is specified to +be kept high when CS is asserted but the controller is not clocking out data to +the peripheral and also when CS is not asserted. + +Peripherals that require this extension must request it by setting the +``SPI_MOSI_IDLE_HIGH`` bit into the mode attribute of their ``struct +spi_device`` and call spi_setup(). Controllers that support this extension +should indicate it by setting ``SPI_MOSI_IDLE_HIGH`` in the mode_bits attribute +of their ``struct spi_controller``. The configuration to idle MOSI low is +analogous but uses the ``SPI_MOSI_IDLE_LOW`` mode bit. + + THANKS TO --------- Contributors to Linux-SPI discussions include (in alphabetical order, diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 6ebe5dd9bbb1..60a2b5a0c85d 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -3921,6 +3921,12 @@ int spi_setup(struct spi_device *spi) (SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL | SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL))) return -EINVAL; + /* Check against conflicting MOSI idle configuration */ + if ((spi->mode & SPI_MOSI_IDLE_LOW) && (spi->mode & SPI_MOSI_IDLE_HIGH)) { + dev_err(&spi->dev, + "setup: MOSI configured to idle low and high at the same time.\n"); + return -EINVAL; + } /* * Help drivers fail *cleanly* when they need options * that aren't supported with their current controller. diff --git a/include/uapi/linux/spi/spi.h b/include/uapi/linux/spi/spi.h index ca56e477d161..ee4ac812b8f8 100644 --- a/include/uapi/linux/spi/spi.h +++ b/include/uapi/linux/spi/spi.h @@ -28,7 +28,8 @@ #define SPI_RX_OCTAL _BITUL(14) /* receive with 8 wires */ #define SPI_3WIRE_HIZ _BITUL(15) /* high impedance turnaround */ #define SPI_RX_CPHA_FLIP _BITUL(16) /* flip CPHA on Rx only xfer */ -#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave mosi line low when idle */ +#define SPI_MOSI_IDLE_LOW _BITUL(17) /* leave MOSI line low when idle */ +#define SPI_MOSI_IDLE_HIGH _BITUL(18) /* leave MOSI line high when idle */ /* * All the bits defined above should be covered by SPI_MODE_USER_MASK. @@ -38,6 +39,6 @@ * These bits must not overlap. A static assert check should make sure of that. * If adding extra bits, make sure to increase the bit index below as well. */ -#define SPI_MODE_USER_MASK (_BITUL(18) - 1) +#define SPI_MODE_USER_MASK (_BITUL(19) - 1) #endif /* _UAPI_SPI_H */