From d875d6ccd36f5eed25829d483b12df6ed826f9b5 Mon Sep 17 00:00:00 2001 From: Zev Weiss Date: Wed, 4 Oct 2023 20:08:50 -0700 Subject: [PATCH] pinctrl: aspeed: Allow changing SPI mode from hardware strap defaults Some platforms unfortunately have their SPI mode selection bits strapped incorrectly (such as being configured for passthrough mode when master mode is in fact the only useful configuration for it) and thus require correction in software. Add the SPI mode bits to the GPIO passthrough bits as the exceptions to the read-only rule for the hardware strap register so that the pinctrl subsystem can be used for such corrections. Signed-off-by: Zev Weiss Reviewed-by: Andrew Jeffery Link: https://lore.kernel.org/r/20231005030849.11352-2-zev@bewilderbeest.net Signed-off-by: Linus Walleij --- drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 19 ++++++++++++------- drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 19 ++++++++++++------- 2 files changed, 24 insertions(+), 14 deletions(-) diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c index bfed0e274643..774f8d05142f 100644 --- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c @@ -2563,15 +2563,20 @@ static int aspeed_g4_sig_expr_set(struct aspeed_pinmux_data *ctx, * deconfigured and is the reason we re-evaluate after writing * all descriptor bits. * - * Port D and port E GPIO loopback modes are the only exception - * as those are commonly used with front-panel buttons to allow - * normal operation of the host when the BMC is powered off or - * fails to boot. Once the BMC has booted, the loopback mode - * must be disabled for the BMC to control host power-on and - * reset. + * We make two exceptions to the read-only rule: + * + * - The passthrough mode of GPIO ports D and E are commonly + * used with front-panel buttons to allow normal operation + * of the host if the BMC is powered off or fails to boot. + * Once the BMC has booted, the loopback mode must be + * disabled for the BMC to control host power-on and reset. + * + * - The operating mode of the SPI1 interface is simply + * strapped incorrectly on some systems and requires a + * software fixup, which we allow to be done via pinctrl. */ if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP1 && - !(desc->mask & (BIT(21) | BIT(22)))) + !(desc->mask & (BIT(22) | BIT(21) | BIT(13) | BIT(12)))) continue; if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP2) diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c index 4c0d26606b6c..5bb8fd0d1e41 100644 --- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c +++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c @@ -2742,15 +2742,20 @@ static int aspeed_g5_sig_expr_set(struct aspeed_pinmux_data *ctx, * deconfigured and is the reason we re-evaluate after writing * all descriptor bits. * - * Port D and port E GPIO loopback modes are the only exception - * as those are commonly used with front-panel buttons to allow - * normal operation of the host when the BMC is powered off or - * fails to boot. Once the BMC has booted, the loopback mode - * must be disabled for the BMC to control host power-on and - * reset. + * We make two exceptions to the read-only rule: + * + * - The passthrough mode of GPIO ports D and E are commonly + * used with front-panel buttons to allow normal operation + * of the host if the BMC is powered off or fails to boot. + * Once the BMC has booted, the loopback mode must be + * disabled for the BMC to control host power-on and reset. + * + * - The operating mode of the SPI1 interface is simply + * strapped incorrectly on some systems and requires a + * software fixup, which we allow to be done via pinctrl. */ if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP1 && - !(desc->mask & (BIT(21) | BIT(22)))) + !(desc->mask & (BIT(22) | BIT(21) | BIT(13) | BIT(12)))) continue; if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP2)