hwmon: add support for THMC50 and ADM1022

This patch adds support for THMC50 and ADM1022 hardware monitoring chips.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This commit is contained in:
Krzysztof Helt 2007-07-08 22:43:00 +02:00 committed by Mark M. Hoffman
parent 80ba80a9bf
commit add77c64ca
4 changed files with 525 additions and 0 deletions

View File

@ -0,0 +1,74 @@
Kernel driver thmc50
=====================
Supported chips:
* Analog Devices ADM1022
Prefix: 'adm1022'
Addresses scanned: I2C 0x2c - 0x2e
Datasheet: http://www.analog.com/en/prod/0,2877,ADM1022,00.html
* Texas Instruments THMC50
Prefix: 'thmc50'
Addresses scanned: I2C 0x2c - 0x2e
Datasheet: http://focus.ti.com/docs/prod/folders/print/thmc50.html
Author: Krzysztof Helt <krzysztof.h1@wp.pl>
This driver was derived from the 2.4 kernel thmc50.c source file.
Credits:
thmc50.c (2.4 kernel):
Frodo Looijaard <frodol@dds.nl>
Philip Edelbrock <phil@netroedge.com>
Module Parameters
-----------------
* adm1022_temp3: short array
List of adapter,address pairs to force chips into ADM1022 mode with
second remote temperature. This does not work for original THMC50 chips.
Description
-----------
The THMC50 implements: an internal temperature sensor, support for an
external diode-type temperature sensor (compatible w/ the diode sensor inside
many processors), and a controllable fan/analog_out DAC. For the temperature
sensors, limits can be set through the appropriate Overtemperature Shutdown
register and Hysteresis register. Each value can be set and read to half-degree
accuracy. An alarm is issued (usually to a connected LM78) when the
temperature gets higher then the Overtemperature Shutdown value; it stays on
until the temperature falls below the Hysteresis value. All temperatures are in
degrees Celsius, and are guaranteed within a range of -55 to +125 degrees.
The THMC50 only updates its values each 1.5 seconds; reading it more often
will do no harm, but will return 'old' values.
The THMC50 is usually used in combination with LM78-like chips, to measure
the temperature of the processor(s).
The ADM1022 works the same as THMC50 but it is faster (5 Hz instead of
1 Hz for THMC50). It can be also put in a new mode to handle additional
remote temperature sensor. The driver use the mode set by BIOS by default.
In case the BIOS is broken and the mode is set incorrectly, you can force
the mode with additional remote temperature with adm1022_temp3 parameter.
A typical symptom of wrong setting is a fan forced to full speed.
Driver Features
---------------
The driver provides up to three temperatures:
temp1 -- internal
temp2 -- remote
temp3 -- 2nd remote only for ADM1022
pwm1 -- fan speed (0 = stop, 255 = full)
pwm1_mode -- always 0 (DC mode)
The value of 0 for pwm1 also forces FAN_OFF signal from the chip,
so it stops fans even if the value 0 into the ANALOG_OUT register does not.
The driver was tested on Compaq AP550 with two ADM1022 chips (one works
in the temp3 mode), five temperature readings and two fans.

View File

@ -520,6 +520,16 @@ config SENSORS_SMSC47B397
This driver can also be built as a module. If so, the module
will be called smsc47b397.
config SENSORS_THMC50
tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for Texas Instruments THMC50
sensor chips and clones: the Analog Devices ADM1022.
This driver can also be built as a module. If so, the module
will be called thmc50.
config SENSORS_VIA686A
tristate "VIA686A"
depends on PCI

View File

@ -56,6 +56,7 @@ obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o
obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
obj-$(CONFIG_SENSORS_SMSC47M1) += smsc47m1.o
obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
obj-$(CONFIG_SENSORS_THMC50) += thmc50.o
obj-$(CONFIG_SENSORS_VIA686A) += via686a.o
obj-$(CONFIG_SENSORS_VT1211) += vt1211.o
obj-$(CONFIG_SENSORS_VT8231) += vt8231.o

440
drivers/hwmon/thmc50.c Normal file
View File

@ -0,0 +1,440 @@
/*
thmc50.c - Part of lm_sensors, Linux kernel modules for hardware
monitoring
Copyright (C) 2007 Krzysztof Helt <krzysztof.h1@wp.pl>
Based on 2.4 driver by Frodo Looijaard <frodol@dds.nl> and
Philip Edelbrock <phil@netroedge.com>
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/err.h>
#include <linux/mutex.h>
MODULE_LICENSE("GPL");
/* Addresses to scan */
static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD_2(thmc50, adm1022);
I2C_CLIENT_MODULE_PARM(adm1022_temp3, "List of adapter,address pairs "
"to enable 3rd temperature (ADM1022 only)");
/* Many THMC50 constants specified below */
/* The THMC50 registers */
#define THMC50_REG_CONF 0x40
#define THMC50_REG_COMPANY_ID 0x3E
#define THMC50_REG_DIE_CODE 0x3F
#define THMC50_REG_ANALOG_OUT 0x19
const static u8 THMC50_REG_TEMP[] = { 0x27, 0x26, 0x20 };
const static u8 THMC50_REG_TEMP_MIN[] = { 0x3A, 0x38, 0x2C };
const static u8 THMC50_REG_TEMP_MAX[] = { 0x39, 0x37, 0x2B };
#define THMC50_REG_CONF_nFANOFF 0x20
/* Each client has this additional data */
struct thmc50_data {
struct i2c_client client;
struct class_device *class_dev;
struct mutex update_lock;
enum chips type;
unsigned long last_updated; /* In jiffies */
char has_temp3; /* !=0 if it is ADM1022 in temp3 mode */
char valid; /* !=0 if following fields are valid */
/* Register values */
s8 temp_input[3];
s8 temp_max[3];
s8 temp_min[3];
u8 analog_out;
};
static int thmc50_attach_adapter(struct i2c_adapter *adapter);
static int thmc50_detach_client(struct i2c_client *client);
static void thmc50_init_client(struct i2c_client *client);
static struct thmc50_data *thmc50_update_device(struct device *dev);
static struct i2c_driver thmc50_driver = {
.driver = {
.name = "thmc50",
},
.attach_adapter = thmc50_attach_adapter,
.detach_client = thmc50_detach_client,
};
static ssize_t show_analog_out(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct thmc50_data *data = thmc50_update_device(dev);
return sprintf(buf, "%d\n", data->analog_out);
}
static ssize_t set_analog_out(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct thmc50_data *data = i2c_get_clientdata(client);
int tmp = simple_strtoul(buf, NULL, 10);
int config;
mutex_lock(&data->update_lock);
data->analog_out = SENSORS_LIMIT(tmp, 0, 255);
i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
data->analog_out);
config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
if (data->analog_out == 0)
config &= ~THMC50_REG_CONF_nFANOFF;
else
config |= THMC50_REG_CONF_nFANOFF;
i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
mutex_unlock(&data->update_lock);
return count;
}
/* There is only one PWM mode = DC */
static ssize_t show_pwm_mode(struct device *dev, struct device_attribute *attr,
char *buf)
{
return sprintf(buf, "0\n");
}
/* Temperatures */
static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
char *buf)
{
int nr = to_sensor_dev_attr(attr)->index;
struct thmc50_data *data = thmc50_update_device(dev);
return sprintf(buf, "%d\n", data->temp_input[nr] * 1000);
}
static ssize_t show_temp_min(struct device *dev, struct device_attribute *attr,
char *buf)
{
int nr = to_sensor_dev_attr(attr)->index;
struct thmc50_data *data = thmc50_update_device(dev);
return sprintf(buf, "%d\n", data->temp_min[nr] * 1000);
}
static ssize_t set_temp_min(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int nr = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct thmc50_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->temp_min[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MIN[nr],
data->temp_min[nr]);
mutex_unlock(&data->update_lock);
return count;
}
static ssize_t show_temp_max(struct device *dev, struct device_attribute *attr,
char *buf)
{
int nr = to_sensor_dev_attr(attr)->index;
struct thmc50_data *data = thmc50_update_device(dev);
return sprintf(buf, "%d\n", data->temp_max[nr] * 1000);
}
static ssize_t set_temp_max(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int nr = to_sensor_dev_attr(attr)->index;
struct i2c_client *client = to_i2c_client(dev);
struct thmc50_data *data = i2c_get_clientdata(client);
int val = simple_strtol(buf, NULL, 10);
mutex_lock(&data->update_lock);
data->temp_max[nr] = SENSORS_LIMIT(val / 1000, -128, 127);
i2c_smbus_write_byte_data(client, THMC50_REG_TEMP_MAX[nr],
data->temp_max[nr]);
mutex_unlock(&data->update_lock);
return count;
}
#define temp_reg(offset) \
static SENSOR_DEVICE_ATTR(temp##offset##_input, S_IRUGO, show_temp, \
NULL, offset - 1); \
static SENSOR_DEVICE_ATTR(temp##offset##_min, S_IRUGO | S_IWUSR, \
show_temp_min, set_temp_min, offset - 1); \
static SENSOR_DEVICE_ATTR(temp##offset##_max, S_IRUGO | S_IWUSR, \
show_temp_max, set_temp_max, offset - 1);
temp_reg(1);
temp_reg(2);
temp_reg(3);
static SENSOR_DEVICE_ATTR(pwm1, S_IRUGO | S_IWUSR, show_analog_out,
set_analog_out, 0);
static SENSOR_DEVICE_ATTR(pwm1_mode, S_IRUGO, show_pwm_mode, NULL, 0);
static struct attribute *thmc50_attributes[] = {
&sensor_dev_attr_temp1_max.dev_attr.attr,
&sensor_dev_attr_temp1_min.dev_attr.attr,
&sensor_dev_attr_temp1_input.dev_attr.attr,
&sensor_dev_attr_temp2_max.dev_attr.attr,
&sensor_dev_attr_temp2_min.dev_attr.attr,
&sensor_dev_attr_temp2_input.dev_attr.attr,
&sensor_dev_attr_pwm1.dev_attr.attr,
&sensor_dev_attr_pwm1_mode.dev_attr.attr,
NULL
};
static const struct attribute_group thmc50_group = {
.attrs = thmc50_attributes,
};
/* for ADM1022 3rd temperature mode */
static struct attribute *adm1022_attributes[] = {
&sensor_dev_attr_temp3_max.dev_attr.attr,
&sensor_dev_attr_temp3_min.dev_attr.attr,
&sensor_dev_attr_temp3_input.dev_attr.attr,
NULL
};
static const struct attribute_group adm1022_group = {
.attrs = adm1022_attributes,
};
static int thmc50_detect(struct i2c_adapter *adapter, int address, int kind)
{
unsigned company;
unsigned revision;
unsigned config;
struct i2c_client *client;
struct thmc50_data *data;
struct device *dev;
int err = 0;
const char *type_name = "";
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
pr_debug("thmc50: detect failed, "
"smbus byte data not supported!\n");
goto exit;
}
/* OK. For now, we presume we have a valid client. We now create the
client structure, even though we cannot fill it completely yet.
But it allows us to access thmc50 registers. */
if (!(data = kzalloc(sizeof(struct thmc50_data), GFP_KERNEL))) {
pr_debug("thmc50: detect failed, kzalloc failed!\n");
err = -ENOMEM;
goto exit;
}
client = &data->client;
i2c_set_clientdata(client, data);
client->addr = address;
client->adapter = adapter;
client->driver = &thmc50_driver;
dev = &client->dev;
pr_debug("thmc50: Probing for THMC50 at 0x%2X on bus %d\n",
client->addr, i2c_adapter_id(client->adapter));
/* Now, we do the remaining detection. */
company = i2c_smbus_read_byte_data(client, THMC50_REG_COMPANY_ID);
revision = i2c_smbus_read_byte_data(client, THMC50_REG_DIE_CODE);
config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
if (kind == 0)
kind = thmc50;
else if (kind < 0) {
err = -ENODEV;
if (revision >= 0xc0 && ((config & 0x10) == 0)) {
if (company == 0x49) {
kind = thmc50;
err = 0;
} else if (company == 0x41) {
kind = adm1022;
err = 0;
}
}
}
if (err == -ENODEV) {
pr_debug("thmc50: Detection of THMC50/ADM1022 failed\n");
goto exit_free;
}
pr_debug("thmc50: Detected %s (version %x, revision %x)\n",
type_name, (revision >> 4) - 0xc, revision & 0xf);
data->type = kind;
if (kind == thmc50)
type_name = "thmc50";
else if (kind == adm1022) {
int id = i2c_adapter_id(client->adapter);
int i;
type_name = "adm1022";
data->has_temp3 = (config >> 7) & 1; /* config MSB */
for (i = 0; i + 1 < adm1022_temp3_num; i += 2)
if (adm1022_temp3[i] == id &&
adm1022_temp3[i + 1] == address) {
/* enable 2nd remote temp */
data->has_temp3 = 1;
break;
}
}
/* Fill in the remaining client fields & put it into the global list */
strlcpy(client->name, type_name, I2C_NAME_SIZE);
mutex_init(&data->update_lock);
/* Tell the I2C layer a new client has arrived */
if ((err = i2c_attach_client(client)))
goto exit_free;
thmc50_init_client(client);
/* Register sysfs hooks */
if ((err = sysfs_create_group(&client->dev.kobj, &thmc50_group)))
goto exit_detach;
/* Register ADM1022 sysfs hooks */
if (data->type == adm1022)
if ((err = sysfs_create_group(&client->dev.kobj,
&adm1022_group)))
goto exit_remove_sysfs_thmc50;
/* Register a new directory entry with module sensors */
data->class_dev = hwmon_device_register(&client->dev);
if (IS_ERR(data->class_dev)) {
err = PTR_ERR(data->class_dev);
goto exit_remove_sysfs;
}
return 0;
exit_remove_sysfs:
if (data->type == adm1022)
sysfs_remove_group(&client->dev.kobj, &adm1022_group);
exit_remove_sysfs_thmc50:
sysfs_remove_group(&client->dev.kobj, &thmc50_group);
exit_detach:
i2c_detach_client(client);
exit_free:
kfree(data);
exit:
return err;
}
static int thmc50_attach_adapter(struct i2c_adapter *adapter)
{
if (!(adapter->class & I2C_CLASS_HWMON))
return 0;
return i2c_probe(adapter, &addr_data, thmc50_detect);
}
static int thmc50_detach_client(struct i2c_client *client)
{
struct thmc50_data *data = i2c_get_clientdata(client);
int err;
hwmon_device_unregister(data->class_dev);
sysfs_remove_group(&client->dev.kobj, &thmc50_group);
if (data->type == adm1022)
sysfs_remove_group(&client->dev.kobj, &adm1022_group);
if ((err = i2c_detach_client(client)))
return err;
kfree(data);
return 0;
}
static void thmc50_init_client(struct i2c_client *client)
{
struct thmc50_data *data = i2c_get_clientdata(client);
int config;
data->analog_out = i2c_smbus_read_byte_data(client,
THMC50_REG_ANALOG_OUT);
/* set up to at least 1 */
if (data->analog_out == 0) {
data->analog_out = 1;
i2c_smbus_write_byte_data(client, THMC50_REG_ANALOG_OUT,
data->analog_out);
}
config = i2c_smbus_read_byte_data(client, THMC50_REG_CONF);
config |= 0x1; /* start the chip if it is in standby mode */
if (data->has_temp3)
config |= 0x80; /* enable 2nd remote temp */
i2c_smbus_write_byte_data(client, THMC50_REG_CONF, config);
}
static struct thmc50_data *thmc50_update_device(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
struct thmc50_data *data = i2c_get_clientdata(client);
int timeout = HZ / 5 + (data->type == thmc50 ? HZ : 0);
mutex_lock(&data->update_lock);
if (time_after(jiffies, data->last_updated + timeout)
|| !data->valid) {
int temps = data->has_temp3 ? 3 : 2;
int i;
for (i = 0; i < temps; i++) {
data->temp_input[i] = i2c_smbus_read_byte_data(client,
THMC50_REG_TEMP[i]);
data->temp_max[i] = i2c_smbus_read_byte_data(client,
THMC50_REG_TEMP_MAX[i]);
data->temp_min[i] = i2c_smbus_read_byte_data(client,
THMC50_REG_TEMP_MIN[i]);
}
data->analog_out =
i2c_smbus_read_byte_data(client, THMC50_REG_ANALOG_OUT);
data->last_updated = jiffies;
data->valid = 1;
}
mutex_unlock(&data->update_lock);
return data;
}
static int __init sm_thmc50_init(void)
{
return i2c_add_driver(&thmc50_driver);
}
static void __exit sm_thmc50_exit(void)
{
i2c_del_driver(&thmc50_driver);
}
MODULE_AUTHOR("Krzysztof Helt <krzysztof.h1@wp.pl>");
MODULE_DESCRIPTION("THMC50 driver");
module_init(sm_thmc50_init);
module_exit(sm_thmc50_exit);