[media] saa7115: add config flag to change the IDQ polarity

Needed by the go7007 driver: it assumes a different polarity of the IDQ
signal, so we need to be able to tell the saa7115 about this.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit is contained in:
Hans Verkuil 2013-03-08 11:22:03 -03:00 committed by Mauro Carvalho Chehab
parent 9ca5470cc1
commit a0fc58868b
2 changed files with 27 additions and 10 deletions

View File

@ -1259,6 +1259,12 @@ static int saa711x_s_routing(struct v4l2_subdev *sd,
(saa711x_read(sd, R_83_X_PORT_I_O_ENA_AND_OUT_CLK) & 0xfe) |
(state->output & 0x01));
}
if (state->ident > V4L2_IDENT_SAA7111A) {
if (config & SAA7115_IDQ_IS_DEFAULT)
saa711x_write(sd, R_85_I_PORT_SIGNAL_POLAR, 0x20);
else
saa711x_write(sd, R_85_I_PORT_SIGNAL_POLAR, 0x21);
}
return 0;
}

View File

@ -21,6 +21,8 @@
#ifndef _SAA7115_H_
#define _SAA7115_H_
/* s_routing inputs, outputs, and config */
/* SAA7111/3/4/5 HW inputs */
#define SAA7115_COMPOSITE0 0
#define SAA7115_COMPOSITE1 1
@ -33,6 +35,25 @@
#define SAA7115_SVIDEO2 8
#define SAA7115_SVIDEO3 9
/* outputs */
#define SAA7115_IPORT_ON 1
#define SAA7115_IPORT_OFF 0
/* SAA7111 specific outputs. */
#define SAA7111_VBI_BYPASS 2
#define SAA7111_FMT_YUV422 0x00
#define SAA7111_FMT_RGB 0x40
#define SAA7111_FMT_CCIR 0x80
#define SAA7111_FMT_YUV411 0xc0
/* config flags */
/* Register 0x85 should set bit 0 to 0 (it's 1 by default). This bit
* controls the IDQ signal polarity which is set to 'inverted' if the bit
* it 1 and to 'default' if it is 0. */
#define SAA7115_IDQ_IS_DEFAULT (1 << 0)
/* s_crystal_freq values and flags */
/* SAA7115 v4l2_crystal_freq frequency values */
#define SAA7115_FREQ_32_11_MHZ 32110000 /* 32.11 MHz crystal, SAA7114/5 only */
#define SAA7115_FREQ_24_576_MHZ 24576000 /* 24.576 MHz crystal */
@ -42,15 +63,5 @@
#define SAA7115_FREQ_FL_CGCDIV (1 << 1) /* SA 3A[6], CGCDIV, SAA7115 only */
#define SAA7115_FREQ_FL_APLL (1 << 2) /* SA 3A[3], APLL, SAA7114/5 only */
#define SAA7115_IPORT_ON 1
#define SAA7115_IPORT_OFF 0
/* SAA7111 specific output flags */
#define SAA7111_VBI_BYPASS 2
#define SAA7111_FMT_YUV422 0x00
#define SAA7111_FMT_RGB 0x40
#define SAA7111_FMT_CCIR 0x80
#define SAA7111_FMT_YUV411 0xc0
#endif