ieee1394: Kconfig menu touch-up

Rename and reorder some prompts and modify some help texts.
The result:

  -------------------- IEEE 1394 (FireWire) support --------------------
  *** Enable only one of the two stacks, unless you know what you are doing ***
  New FireWire stack, EXPERIMENTAL
    OHCI-1394 controllers
    Storage devices (SBP-2 protocol)
  Stable FireWire stack
    OHCI-1394 controllers
    PCILynx controller
    Storage devices (SBP-2 protocol)
      Enable replacement for physical DMA in SBP2
    IP over 1394
    raw1394 userspace interface
    video1394 userspace interface
    dv1394 userspace interface (deprecated)
    Excessive debugging output

The old prompts for reference:

  -------------------- IEEE 1394 (FireWire) support --------------------
  IEEE 1394 (FireWire) support - alternative stack, EXPERIMENTAL
    Support for OHCI FireWire host controllers
    Support for storage devices (SBP-2 protocol driver)
  IEEE 1394 (FireWire) support
    *** Subsystem Options ***
    Excessive debugging output
    *** Controllers ***
    Texas Instruments PCILynx support
    OHCI-1394 support
    *** Protocols ***
    OHCI-1394 Video support
    SBP-2 support (Harddisks etc.)
      Enable replacement for physical DMA in SBP2
    IP over 1394
    OHCI-DV I/O support (deprecated)
    Raw IEEE1394 I/O support

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This commit is contained in:
Stefan Richter 2008-06-16 01:39:28 +02:00
parent a7b64b8704
commit 9499fe2b34

View File

@ -4,7 +4,7 @@ menu "IEEE 1394 (FireWire) support"
source "drivers/firewire/Kconfig"
config IEEE1394
tristate "IEEE 1394 (FireWire) support"
tristate "Stable FireWire stack"
depends on PCI || BROKEN
help
IEEE 1394 describes a high performance serial bus, which is also
@ -19,30 +19,45 @@ config IEEE1394
To compile this driver as a module, say M here: the
module will be called ieee1394.
comment "Subsystem Options"
depends on IEEE1394
config IEEE1394_VERBOSEDEBUG
bool "Excessive debugging output"
depends on IEEE1394
config IEEE1394_OHCI1394
tristate "OHCI-1394 controllers"
depends on PCI && IEEE1394
help
If you say Y here, you will get very verbose debugging logs from
the subsystem which includes a dump of the header of every sent
and received packet. This can amount to a high amount of data
collected in a very short time which is usually also saved to
disk by the system logging daemons.
Enable this driver if you have an IEEE 1394 controller based on the
OHCI-1394 specification. The current driver is only tested with OHCI
chipsets made by Texas Instruments and NEC. Most third-party vendors
use one of these chipsets. It should work with any OHCI-1394
compliant card, however.
Say Y if you really want or need the debugging output, everyone
else says N.
To compile this driver as a module, say M here: the
module will be called ohci1394.
comment "Controllers"
depends on IEEE1394
NOTE:
comment "Texas Instruments PCILynx requires I2C"
You should only build either ohci1394 or the new firewire-ohci driver,
but not both. If you nevertheless want to install both, you should
configure them only as modules and blacklist the driver(s) which you
don't want to have auto-loaded. Add either
blacklist firewire-ohci
or
blacklist ohci1394
blacklist video1394
blacklist dv1394
to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf
depending on your distribution. The latter two modules should be
blacklisted together with ohci1394 because they depend on ohci1394.
If you have an old modprobe which doesn't implement the blacklist
directive, use "install modulename /bin/true" for the modules to be
blacklisted.
comment "PCILynx controller requires I2C"
depends on IEEE1394 && I2C=n
config IEEE1394_PCILYNX
tristate "Texas Instruments PCILynx support"
tristate "PCILynx controller"
depends on PCI && IEEE1394 && I2C
select I2C_ALGOBIT
help
@ -57,35 +72,11 @@ config IEEE1394_PCILYNX
PowerMacs G3 B&W contain the PCILynx controller. Therefore
almost everybody can say N here.
config IEEE1394_OHCI1394
tristate "OHCI-1394 support"
depends on PCI && IEEE1394
help
Enable this driver if you have an IEEE 1394 controller based on the
OHCI-1394 specification. The current driver is only tested with OHCI
chipsets made by Texas Instruments and NEC. Most third-party vendors
use one of these chipsets. It should work with any OHCI-1394
compliant card, however.
To compile this driver as a module, say M here: the
module will be called ohci1394.
comment "Protocols"
depends on IEEE1394
config IEEE1394_VIDEO1394
tristate "OHCI-1394 Video support"
depends on IEEE1394 && IEEE1394_OHCI1394
help
This option enables video device usage for OHCI-1394 cards. Enable
this option only if you have an IEEE 1394 video device connected to
an OHCI-1394 card.
comment "SBP-2 support (for storage devices) requires SCSI"
depends on IEEE1394 && SCSI=n
config IEEE1394_SBP2
tristate "SBP-2 support (Harddisks etc.)"
tristate "Storage devices (SBP-2 protocol)"
depends on IEEE1394 && SCSI
help
This option enables you to use SBP-2 devices connected to an IEEE
@ -127,24 +118,47 @@ config IEEE1394_ETH1394
The module is called eth1394 although it does not emulate Ethernet.
config IEEE1394_RAWIO
tristate "raw1394 userspace interface"
depends on IEEE1394
help
This option adds support for the raw1394 device file which enables
direct communication of user programs with IEEE 1394 devices
(isochronous and asynchronous). Almost all application programs
which access FireWire require this option.
To compile this driver as a module, say M here: the module will be
called raw1394.
config IEEE1394_VIDEO1394
tristate "video1394 userspace interface"
depends on IEEE1394 && IEEE1394_OHCI1394
help
This option adds support for the video1394 device files which enable
isochronous communication of user programs with IEEE 1394 devices,
especially video capture or export. This interface is used by all
libdc1394 based programs and by several other programs, in addition to
the raw1394 interface. It is generally not required for DV capture.
To compile this driver as a module, say M here: the module will be
called video1394.
config IEEE1394_DV1394
tristate "OHCI-DV I/O support (deprecated)"
tristate "dv1394 userspace interface (deprecated)"
depends on IEEE1394 && IEEE1394_OHCI1394
help
The dv1394 driver is unsupported and may be removed from Linux in a
future release. Its functionality is now provided by raw1394 together
with libraries such as libiec61883.
config IEEE1394_RAWIO
tristate "Raw IEEE1394 I/O support"
config IEEE1394_VERBOSEDEBUG
bool "Excessive debugging output"
depends on IEEE1394
help
This option adds support for the raw1394 device file which enables
direct communication of user programs with the IEEE 1394 bus and thus
with the attached peripherals. Almost all application programs which
access FireWire require this option.
If you say Y here, you will get very verbose debugging logs from the
ieee1394 drivers, including sent and received packet headers. This
will quickly result in large amounts of data sent to the system log.
To compile this driver as a module, say M here: the module will be
called raw1394.
Say Y if you really need the debugging output. Everyone else says N.
endmenu