diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 913c11390a45..ea3b5be8fe4f 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -206,6 +206,7 @@ Hardware Monitoring Kernel Drivers sch5636 scpi-hwmon sfctemp + sg2042-mcu sht15 sht21 sht3x diff --git a/Documentation/hwmon/sg2042-mcu.rst b/Documentation/hwmon/sg2042-mcu.rst new file mode 100644 index 000000000000..077e79841d2e --- /dev/null +++ b/Documentation/hwmon/sg2042-mcu.rst @@ -0,0 +1,78 @@ +.. SPDX-License-Identifier: GPL-2.0 + +Kernel driver sg2042-mcu +======================== + +Supported chips: + + * Onboard MCU for sg2042 + + Addresses scanned: - + + Prefix: 'sg2042-mcu' + +Authors: + + - Inochi Amaoto + +Description +----------- + +This driver supprts hardware monitoring for onboard MCU with +i2c interface. + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate +the devices explicitly. +Please see Documentation/i2c/instantiating-devices.rst for details. + +Sysfs Attributes +---------------- + +The following table shows the standard entries support by the driver: + +================= ===================================================== +Name Description +================= ===================================================== +temp1_input Measured temperature of SoC +temp1_crit Critical high temperature +temp1_crit_hyst hysteresis temperature restore from Critical +temp2_input Measured temperature of the base board +================= ===================================================== + +The following table shows the extra entries support by the driver +(the MCU device is in i2c subsystem): + +================= ======= ============================================= +Name Perm Description +================= ======= ============================================= +reset_count RO Reset count of the SoC +uptime RO Seconds after the MCU is powered +reset_reason RO Reset reason for the last reset +repower_policy RW Execution policy when triggering repower +================= ======= ============================================= + +``repower_policy`` + The repower is triggered when the temperature of the SoC falls below + the hysteresis temperature after triggering a shutdown due to + reaching the critical temperature. + The valid values for this entry are "repower" and "keep". "keep" will + leave the SoC down when the triggering repower, and "repower" will + boot the SoC. + +Debugfs Interfaces +------------------ + +If debugfs is available, this driver exposes some hardware specific +data in ``/sys/kernel/debug/sg2042-mcu/*/``. + +================= ======= ============================================= +Name Format Description +================= ======= ============================================= +firmware_version 0x%02x firmware version of the MCU +pcb_version 0x%02x version number of the base board +board_type 0x%02x identifiers for the base board +mcu_type %d type of the MCU: 0 is STM32, 1 is GD32 +================= ======= ============================================= diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 1db349ecb1a4..65ea92529406 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -2068,6 +2068,17 @@ config SENSORS_SFCTEMP This driver can also be built as a module. If so, the module will be called sfctemp. +config SENSORS_SG2042_MCU + tristate "Sophgo onboard MCU support" + depends on I2C + depends on ARCH_SOPHGO || COMPILE_TEST + help + Support for onboard MCU of Sophgo SG2042 SoCs. This mcu provides + power control and some basic information. + + This driver can be built as a module. If so, the module + will be called sg2042-mcu. + config SENSORS_SURFACE_FAN tristate "Surface Fan Driver" depends on SURFACE_AGGREGATOR diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 3ce8d6a9202e..9554d2fdcf7b 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -194,6 +194,7 @@ obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o obj-$(CONFIG_SENSORS_SFCTEMP) += sfctemp.o +obj-$(CONFIG_SENSORS_SG2042_MCU) += sg2042-mcu.o obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o obj-$(CONFIG_SENSORS_SHT15) += sht15.o obj-$(CONFIG_SENSORS_SHT21) += sht21.o diff --git a/drivers/hwmon/sg2042-mcu.c b/drivers/hwmon/sg2042-mcu.c new file mode 100644 index 000000000000..141045769354 --- /dev/null +++ b/drivers/hwmon/sg2042-mcu.c @@ -0,0 +1,388 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2024 Inochi Amaoto + * + * Sophgo power control mcu for SG2042 + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +/* fixed MCU registers */ +#define REG_BOARD_TYPE 0x00 +#define REG_MCU_FIRMWARE_VERSION 0x01 +#define REG_PCB_VERSION 0x02 +#define REG_PWR_CTRL 0x03 +#define REG_SOC_TEMP 0x04 +#define REG_BOARD_TEMP 0x05 +#define REG_RST_COUNT 0x0a +#define REG_UPTIME 0x0b +#define REG_RESET_REASON 0x0d +#define REG_MCU_TYPE 0x18 +#define REG_REPOWER_POLICY 0x65 +#define REG_CRITICAL_TEMP 0x66 +#define REG_REPOWER_TEMP 0x67 + +#define REPOWER_POLICY_REBOOT 1 +#define REPOWER_POLICY_KEEP_OFF 2 + +#define MCU_POWER_MAX 0xff + +#define DEFINE_MCU_DEBUG_ATTR(_name, _reg, _format) \ + static int _name##_show(struct seq_file *seqf, \ + void *unused) \ + { \ + struct sg2042_mcu_data *mcu = seqf->private; \ + int ret; \ + ret = i2c_smbus_read_byte_data(mcu->client, (_reg)); \ + if (ret < 0) \ + return ret; \ + seq_printf(seqf, _format "\n", ret); \ + return 0; \ + } \ + DEFINE_SHOW_ATTRIBUTE(_name) \ + +struct sg2042_mcu_data { + struct i2c_client *client; + struct dentry *debugfs; + struct mutex mutex; +}; + +static struct dentry *sgmcu_debugfs; + +static ssize_t reset_count_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + int ret; + + ret = i2c_smbus_read_byte_data(mcu->client, REG_RST_COUNT); + if (ret < 0) + return ret; + + return sprintf(buf, "%d\n", ret); +} + +static ssize_t uptime_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + u8 time_val[2]; + int ret; + + ret = i2c_smbus_read_i2c_block_data(mcu->client, REG_UPTIME, + sizeof(time_val), time_val); + if (ret < 0) + return ret; + + return sprintf(buf, "%d\n", + (time_val[0]) | (time_val[1] << 8)); +} + +static ssize_t reset_reason_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + int ret; + + ret = i2c_smbus_read_byte_data(mcu->client, REG_RESET_REASON); + if (ret < 0) + return ret; + + return sprintf(buf, "0x%02x\n", ret); +} + +static ssize_t repower_policy_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + int ret; + const char *action; + + ret = i2c_smbus_read_byte_data(mcu->client, REG_REPOWER_POLICY); + if (ret < 0) + return ret; + + if (ret == REPOWER_POLICY_REBOOT) + action = "repower"; + else if (ret == REPOWER_POLICY_KEEP_OFF) + action = "keep"; + else + action = "unknown"; + + return sprintf(buf, "%s\n", action); +} + +static ssize_t repower_policy_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + u8 value; + int ret; + + if (sysfs_streq("repower", buf)) + value = REPOWER_POLICY_REBOOT; + else if (sysfs_streq("keep", buf)) + value = REPOWER_POLICY_KEEP_OFF; + else + return -EINVAL; + + ret = i2c_smbus_write_byte_data(mcu->client, + REG_REPOWER_POLICY, value); + if (ret < 0) + return ret; + + return count; +} + +static DEVICE_ATTR_RO(reset_count); +static DEVICE_ATTR_RO(uptime); +static DEVICE_ATTR_RO(reset_reason); +static DEVICE_ATTR_RW(repower_policy); + +DEFINE_MCU_DEBUG_ATTR(firmware_version, REG_MCU_FIRMWARE_VERSION, "0x%02x"); +DEFINE_MCU_DEBUG_ATTR(pcb_version, REG_PCB_VERSION, "0x%02x"); +DEFINE_MCU_DEBUG_ATTR(board_type, REG_BOARD_TYPE, "0x%02x"); +DEFINE_MCU_DEBUG_ATTR(mcu_type, REG_MCU_TYPE, "%d"); + +static struct attribute *sg2042_mcu_attrs[] = { + &dev_attr_reset_count.attr, + &dev_attr_uptime.attr, + &dev_attr_reset_reason.attr, + &dev_attr_repower_policy.attr, + NULL +}; + +static const struct attribute_group sg2042_mcu_attr_group = { + .attrs = sg2042_mcu_attrs, +}; + +static const struct attribute_group *sg2042_mcu_groups[] = { + &sg2042_mcu_attr_group, + NULL +}; + +static const struct hwmon_channel_info * const sg2042_mcu_info[] = { + HWMON_CHANNEL_INFO(chip, HWMON_C_REGISTER_TZ), + HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT | HWMON_T_CRIT | + HWMON_T_CRIT_HYST, + HWMON_T_INPUT), + NULL +}; + +static int sg2042_mcu_read(struct device *dev, + enum hwmon_sensor_types type, + u32 attr, int channel, long *val) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + int tmp; + u8 reg; + + switch (attr) { + case hwmon_temp_input: + reg = channel ? REG_BOARD_TEMP : REG_SOC_TEMP; + break; + case hwmon_temp_crit: + reg = REG_CRITICAL_TEMP; + break; + case hwmon_temp_crit_hyst: + reg = REG_REPOWER_TEMP; + break; + default: + return -EOPNOTSUPP; + } + + tmp = i2c_smbus_read_byte_data(mcu->client, reg); + if (tmp < 0) + return tmp; + *val = tmp * 1000; + + return 0; +} + +static int sg2042_mcu_write(struct device *dev, + enum hwmon_sensor_types type, + u32 attr, int channel, long val) +{ + struct sg2042_mcu_data *mcu = dev_get_drvdata(dev); + int temp = val / 1000; + int hyst_temp, crit_temp; + u8 reg; + + temp = clamp_val(temp, 0, MCU_POWER_MAX); + + guard(mutex)(&mcu->mutex); + + switch (attr) { + case hwmon_temp_crit: + hyst_temp = i2c_smbus_read_byte_data(mcu->client, + REG_REPOWER_TEMP); + if (hyst_temp < 0) + return hyst_temp; + + crit_temp = temp; + reg = REG_CRITICAL_TEMP; + break; + case hwmon_temp_crit_hyst: + crit_temp = i2c_smbus_read_byte_data(mcu->client, + REG_CRITICAL_TEMP); + if (crit_temp < 0) + return crit_temp; + + hyst_temp = temp; + reg = REG_REPOWER_TEMP; + break; + default: + return -EOPNOTSUPP; + } + + /* + * ensure hyst_temp is smaller to avoid MCU from + * keeping triggering repower event. + */ + if (crit_temp < hyst_temp) + return -EINVAL; + + return i2c_smbus_write_byte_data(mcu->client, reg, temp); +} + +static umode_t sg2042_mcu_is_visible(const void *_data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + switch (type) { + case hwmon_temp: + switch (attr) { + case hwmon_temp_input: + return 0444; + case hwmon_temp_crit: + case hwmon_temp_crit_hyst: + if (channel == 0) + return 0644; + break; + default: + break; + } + break; + default: + break; + } + return 0; +} + +static const struct hwmon_ops sg2042_mcu_ops = { + .is_visible = sg2042_mcu_is_visible, + .read = sg2042_mcu_read, + .write = sg2042_mcu_write, +}; + +static const struct hwmon_chip_info sg2042_mcu_chip_info = { + .ops = &sg2042_mcu_ops, + .info = sg2042_mcu_info, +}; + +static void sg2042_mcu_debugfs_init(struct sg2042_mcu_data *mcu, + struct device *dev) +{ + mcu->debugfs = debugfs_create_dir(dev_name(dev), sgmcu_debugfs); + + debugfs_create_file("firmware_version", 0444, mcu->debugfs, + mcu, &firmware_version_fops); + debugfs_create_file("pcb_version", 0444, mcu->debugfs, mcu, + &pcb_version_fops); + debugfs_create_file("mcu_type", 0444, mcu->debugfs, mcu, + &mcu_type_fops); + debugfs_create_file("board_type", 0444, mcu->debugfs, mcu, + &board_type_fops); +} + +static int sg2042_mcu_i2c_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + struct sg2042_mcu_data *mcu; + struct device *hwmon_dev; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA | + I2C_FUNC_SMBUS_BLOCK_DATA)) + return -ENODEV; + + mcu = devm_kmalloc(dev, sizeof(*mcu), GFP_KERNEL); + if (!mcu) + return -ENOMEM; + + mutex_init(&mcu->mutex); + mcu->client = client; + + i2c_set_clientdata(client, mcu); + + hwmon_dev = devm_hwmon_device_register_with_info(dev, "sg2042_mcu", + mcu, + &sg2042_mcu_chip_info, + NULL); + if (IS_ERR(hwmon_dev)) + return PTR_ERR(hwmon_dev); + + sg2042_mcu_debugfs_init(mcu, dev); + + return 0; +} + +static void sg2042_mcu_i2c_remove(struct i2c_client *client) +{ + struct sg2042_mcu_data *mcu = i2c_get_clientdata(client); + + debugfs_remove_recursive(mcu->debugfs); +} + +static const struct i2c_device_id sg2042_mcu_id[] = { + { "sg2042-hwmon-mcu", 0 }, + {}, +}; +MODULE_DEVICE_TABLE(i2c, sg2042_mcu_id); + +static const struct of_device_id sg2042_mcu_of_id[] = { + { .compatible = "sophgo,sg2042-hwmon-mcu" }, + {}, +}; +MODULE_DEVICE_TABLE(of, sg2042_mcu_of_id); + +static struct i2c_driver sg2042_mcu_driver = { + .driver = { + .name = "sg2042-mcu", + .of_match_table = sg2042_mcu_of_id, + .dev_groups = sg2042_mcu_groups, + }, + .probe = sg2042_mcu_i2c_probe, + .remove = sg2042_mcu_i2c_remove, + .id_table = sg2042_mcu_id, +}; + +static int __init sg2042_mcu_init(void) +{ + sgmcu_debugfs = debugfs_create_dir("sg2042-mcu", NULL); + return i2c_add_driver(&sg2042_mcu_driver); +} + +static void __exit sg2042_mcu_exit(void) +{ + debugfs_remove_recursive(sgmcu_debugfs); + i2c_del_driver(&sg2042_mcu_driver); +} + +module_init(sg2042_mcu_init); +module_exit(sg2042_mcu_exit); + +MODULE_AUTHOR("Inochi Amaoto "); +MODULE_DESCRIPTION("MCU I2C driver for SG2042 soc platform"); +MODULE_LICENSE("GPL");