[PATCH] libertas: Purge non-mesh ioctls

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit is contained in:
Dan Williams 2007-05-10 23:04:39 -04:00 committed by John W. Linville
parent 3ce4023275
commit 4b19fcc363
6 changed files with 0 additions and 2363 deletions

View File

@ -40,64 +40,11 @@ NAME
SYNOPSIS
iwpriv <ethX> <command> [sub-command] ...
iwpriv ethX version
iwpriv ethX scantype [sub-command]
iwpriv ethX getSNR <n>
iwpriv ethX getNF <n>
iwpriv ethX getRSSI <n>
iwpriv ethX setrxant <n>
iwpriv ethX getrxant
iwpriv ethX settxant <n>
iwpriv ethX gettxant
iwpriv ethX authalgs <n>
iwpriv ethX pre-TBTT <n>
iwpriv ethX 8021xauthalgs <n>
iwpriv ethX encryptionmode <n>
iwpriv ethX setregioncode <n>
iwpriv ethX getregioncode
iwpriv ethX setbcnavg <n>
iwpriv ethX getbcnavg
iwpriv ethX setdataavg <n>
iwpriv ethX setlisteninter <n>
iwpriv ethX getlisteninter
iwpriv ethX setmultipledtim <n>
iwpriv ethX getmultipledtim
iwpriv ethX atimwindow <n>
iwpriv ethX deauth
iwpriv ethX adhocstop
iwpriv ethX radioon
iwpriv ethX radiooff
iwpriv ethX reasso-on
iwpriv ethX reasso-off
iwpriv ethX scanmode [sub-command]
iwpriv ethX setwpaie <n>
iwpriv ethX wlanidle-off
iwpriv ethX wlanidle-on
iwpriv ethX getcis
iwpriv ethX getlog
iwpriv ethX getadhocstatus
iwpriv ethX adhocgrate <n>
Version 4 Command:
iwpriv ethX inactvityto <n>
iwpriv ethX sleeppd <n>
iwpriv ethX enable11d <n>
iwpriv ethX tpccfg <n>
iwpriv ethX powercfg <n>
iwpriv ethX setafc <n>
iwpriv ethX getafc
Version 5 Command:
iwpriv ethX ledgpio <n>
iwpriv ethX scanprobes <n>
iwpriv ethX lolisteninter <n>
iwpriv ethX rateadapt <n> <m>
iwpriv ethX txcontrol <n>
iwpriv ethX psnullinterval <n>
iwpriv ethX prescan <n>
iwpriv ethX getrxinfo
iwpriv ethX gettxrate
iwpriv ethX beaconinterval
BT Commands:
The blinding table (BT) contains a list of mac addresses that should be
@ -150,114 +97,6 @@ DESCRIPTION
The ethX parameter specifies the network device that is to be used to
perform this command on. it could be eth0, eth1 etc.
version
This is used to get the current version of the driver and the firmware.
scantype
This command is used to set the scan type to be used by the driver in
the scan command. This setting will not be used while performing a scan
for a specific SSID, as it is always done with scan type being active.
where the sub-commands are: -
active -- to set the scan type to active
passive -- to set the scan type to passive
get -- to get the scan type set in the driver
getSNR
This command gets the average and non average value of Signal to Noise
Ratio of Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
If no value is given, all four values are returned in the order mentioned
above.
Note: This command is available only when STA is connected.
getRSSI
This command gets the average and non average value os Receive Signal
Strength of Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
Note: This command is available only when STA is connected.
getNF
This command gets the average and non average value of Noise Floor of
Beacon and Data.
where value is:-
0 -- Beacon non-average.
1 -- Beacon average.
2 -- Data non-average.
3 -- Data average.
Note: This command is available only when STA is connected.
setrxant
This command is used to set the mode for Rx antenna.
The options that can be sent are:-
1 -- Antenna 1.
2 -- Antenna 2.
0xFFFF -- Diversity.
Usage:
iwpriv ethX setrxant 0x01: select Antenna 1.
getrxant
This command is used to get the mode for Rx antenna.
settxant
This command is used to set the mode for Tx antenna.
The options that can be sent are:-
1 -- Antenna 1.
2 -- Antenna 2.
0xFFFF -- Diversity.
Usage:
iwpriv ethX settxant 0x01: select Antenna 1.
gettxant
This command is used to get the mode for Tx antenna.
authalgs
This command is used by the WPA supplicant to set the authentication
algorithms in the station.
8021xauthalgs
This command is used by the WPA supplicant to set the 8021.x authentication algorithm type
station.
where values can be:-
1 -- None
2 -- LEAP
4 -- TLS
8 -- TTLs
16 -- MD5
encryptionmode
This command is used by the WPA supplicant to set the encryption algorithm.
where values can be:-
0 -- NONE
1 -- WEP40
2 -- TKIP
3 -- CCMP
4 -- WEP104
pre-TBTT
This command is used to set pre-TBTT time period where value is in microseconds.
setregioncode
This command is used to set the region code in the station.
where value is 'region code' for various regions like
@ -270,114 +109,6 @@ getregioncode
This command is used to get the region code information set in the
station.
setbcnavg
Set the weighting factor for calculating RSSI.
getbcnavg
Get weighting factor for calculating RSSI.
setdataavg
Set the weighting factor for calculating SNR.
setlisteninter
This command is used to set the listen interval in the
station.
where the value ranges between 1 - 255
getlisteninter
This command is used to get the listen interval value set in the
station.
setmultipledtim
This command is used to set the multiple dtim value in the
station.
where the value is 1,2,3,4,5,0xfffe
0xfffe means the firmware will use listen interval in association
command for waking up
getmultipledtim
This command is used to get the multiple dtim value set in the station.
atimwindow
This command is used to set the atim value in the
station.
where the value ranges between 0 - 50
deauth
This command is used to send the de-authentication to the AP with which
the station is associated. This command is valid only when
station is in Infrastructure mode.
Note: This command is available only when STA is connected.
adhocstop
This command is used to stop beacon transmission from the station and
go into idle state in ad-hoc mode.
Note: This command is available only when STA is connected.
radioon
This command is used to turn on the RF antenna.
radiooff
This command is sued to turn off the RF antenna.
scanmode
This command is used to set the station to scan for either IBSS
networks or BSS networks or both BSS and IBSS networks. This
command can be used with sub commands,
where the value for
bss -- Scan All the BSS networks.
ibss -- Scan All the IBSS networks.
any -- Scan both BSS and IBSS networks.
setwpaie
This command is used by WPA supplicant to send the WPA-IE to the driver.
wlanidle-off
This command is used to get into idle state.
Note: This command is available only when STA is connected.
wlanidle-on
This command is used to get off the idle state.
Note: This command is available only when STA is connected.
getlog
This command is used to get the 802.11 statistics available in the
station.
Note: This command is available only when STA is connected.
getadhocstatus
This command is used to get the ad-hoc Network Status.
The various status codes are:
AdhocStarted
AdhocJoined
AdhocIdle
InfraMode
AutoUnknownMode
Note: This command is available only when STA is connected.
adhocgrate
This command is used to enable(1) g_rate, Disable(0) g_rate
and request(2) the status which g_rate is disabled/enabled,
for Ad-hoc creator.
where value is:-
0 -- Disabled
1 -- Enabled
2 -- Get
ledgpio
This command is used to set/get LEDs.
@ -400,253 +131,6 @@ ledgpio
Note: LED0 is invalid
Note: Maximum Number of LEDs are 16.
inactivityto
This command is used by the host to set/get the inactivity timeout value,
which specifies when WLAN device is put to sleep.
Usage:
iwpriv ethX inactivityto [<timeout>]
where the parameter are:
timeout: timeout value in milliseconds.
Example:
iwpriv eth1 inactivityto
"get the timeout value"
iwpriv eth1 inactivityto X
"set timeout value to X ms"
sleeppd
This command is used to configure the sleep period of the WLAN device.
Usage:
iwpriv ethX sleeppd [<sleep period>]
where the parameter are:
Period: sleep period in milliseconds. Range 10~60.
Example:
iwpriv eth1 sleeppd 10
"set period as 10 ms"
iwpriv eth1 sleeppd
"get the sleep period configuration"
enable11d
This command is used to control 11d
where value is:-
1 -- Enabled
0 -- Disabled
2 -- Get
tpccfg
Enables or disables automatic transmit power control.
The first parameter turns this feature on (1) or off (0). When turning
on, the user must also supply four more parameters in the following
order:
-UseSNR (Use SNR (in addition to PER) for TPC algorithm),
-P0 (P0 power level for TPC),
-P1 (P1 power level for TPC),
-P2 (P2 power level for TPC).
Usage:
iwpriv ethX tpccfg: Get current configuration
iwpriv ethX tpccfg 0: disable auto TPC
iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR;
P0=0x05; P1=0x0a; P2=0x0d;
iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR;
P0=0x05; P1=0x0a; P2=0x0d.
powercfg
Enables or disables power adaptation.
The first parameter turns this feature on (1) or off (0). When turning
on, the user must also supply three more parameters in the following
order:
-P0 (P0 power level for Power Adaptation),
-P1 (P1 power level for Power Adaptation),
-P2 (P2 power level for Power Adaptation).
Usage:
iwpriv ethX powercfg: Get current configuration
iwpriv ethX powercfg 0: disable power adaptation
iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation;
P0=0x0d; P1=0x0f; P2=0x12.
getafc
This command returns automatic frequency control parameters. It returns
three integers:
-P0: automatic is on (1), or off (0),
-P1: current timing offset in PPM (part per million), and
-P2: current frequency offset in PPM.
setafc
Set automatic frequency control options.
The first parameter turns automatic on (1) or off (0).
The user must supply two more parameters in either case, in the following
order:
When auto is on:
-P0 (automatic adjustment frequency threshold in PPM),
-P1 (automatic adjustment period in beacon period),
When auto is off:
-P0 (manual adjustment timing offset in PPM), and
-P1 (manual adjustment frequency offset in PPM).
Usage:
iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy
offset are 10 PPM.
iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment,
frequency threshold 10 PPM, for every 10 beacon periods.
scanprobes
This command sets number of probe requests per channel.
Usage:
iwpriv ethX scanprobes 3 (set scan probes to 3)
iwpriv ethX scanprobes (get scan probes)
lolisteninter
This command sets the value of listen interval.
Usage:
iwpriv ethX lolisteninter 234 (set the lolisteninter to 234)
iwpriv ethX lolisteninter (get the lolisteninter value)
rateadapt
This command sets the data rates bitmap.
Where <n>
0: Disable auto rate adapt
1: Enable auto rate adapt
<m>
data rate bitmap
Bit Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
12-15 Reserved
Usage:
iwpriv ethX rateadapt
read the currect data rate setting
iwpriv ethX rateadapt 1 0x07
enable auto data rate adapt and
data rates are 1Mbps, 2Mbsp and 5.5Mbps
txcontrol
This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis.
Where value <n> is:
if bit[4] == 1:
bit[3:0] -- 0 1 2 3 4 5 6 7 8 9 10 11 12 13-16
Data Rate(Mbps) -- 1 2 5.5 11 Rsv 6 9 12 18 24 36 48 54 Rsv
bit[12:8]
if bit[12] == 1, bit[11:8] specifies the Tx retry limit.
bit[14:13] specifies per packet ack policy:
bit[14:13]
1 0 use immediate ack policy for this packet
1 1 use no ack policy for this packet
0 x use the per-packet ack policy setting
Usage:
iwpriv ethX txcontrol 0x7513
Use no-ack policy, 5 retires for Tx, 11Mbps rate
psnullinterval
This command is used to set/request NULL package interval for Power Save
under infrastructure mode.
where value is:-
-1 -- Disabled
n>0 -- Set interval as n (seconds)
prescan
This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap
where value is:-
0 -- Disabled
1 -- Enabled
2 -- Get
getrxinfo
This command gets non average value of Signal to Noise Ratio of Data and rate index.
The following table shows RateIndex and Rate
RateIndex Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
13-15 Reserved
gettxrate
This command gets current Tx rate index of the first packet associated with Rate Adaptation.
The following table shows RateIndex and Rate
RateIndex Data rate
0 1 Mbps
1 2 Mbps
2 5.5 Mbps
3 11 Mbps
4 Reserved
5 6 Mbps
6 9 Mbps
7 12 Mbps
8 18 Mbps
9 24 Mbps
10 36 Mbps
11 48 Mbps
12 54 Mbps
13-15 Reserved
bcninterval
This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc
beacon interval when no argument is given. The valid beacon interval is between 20 - 1000,
default beacon interval is 100.
Usage:
iwpriv ethX bcninterval 100 (set adhoc beacon interval to 100)
iwpriv ethX bcninterval (get adhoc beacon interval)
fwt_add
This command is used to insert an entry into the FWT table. The list of
parameters must follow the following structure:

File diff suppressed because it is too large Load Diff

View File

@ -96,20 +96,6 @@ int libertas_send_deauth(wlan_private * priv)
return ret;
}
int libertas_do_adhocstop_ioctl(wlan_private * priv)
{
wlan_adapter *adapter = priv->adapter;
int ret = 0;
if (adapter->mode == IW_MODE_ADHOC &&
adapter->connect_status == libertas_connected)
ret = libertas_stop_adhoc_network(priv);
else
ret = -ENOTSUPP;
return ret;
}
/**
* @brief Associate to a specific BSS discovered in a scan
*
@ -261,127 +247,6 @@ int libertas_send_deauthentication(wlan_private * priv)
0, cmd_option_waitforrsp, 0, NULL);
}
/**
* @brief Set Idle Off
*
* @param priv A pointer to wlan_private structure
* @return 0 --success, otherwise fail
*/
int libertas_idle_off(wlan_private * priv)
{
wlan_adapter *adapter = priv->adapter;
int ret = 0;
const u8 zeromac[] = { 0, 0, 0, 0, 0, 0 };
int i;
ENTER();
if (adapter->connect_status == libertas_disconnected) {
if (adapter->mode == IW_MODE_INFRA) {
if (memcmp(adapter->previousbssid, zeromac,
sizeof(zeromac)) != 0) {
lbs_pr_debug(1, "Previous SSID = %s\n",
adapter->previousssid.ssid);
lbs_pr_debug(1, "Previous BSSID = "
"%02x:%02x:%02x:%02x:%02x:%02x:\n",
adapter->previousbssid[0],
adapter->previousbssid[1],
adapter->previousbssid[2],
adapter->previousbssid[3],
adapter->previousbssid[4],
adapter->previousbssid[5]);
i = libertas_find_SSID_in_list(adapter,
&adapter->previousssid,
adapter->previousbssid,
adapter->mode);
if (i < 0) {
libertas_send_specific_BSSID_scan(priv,
adapter->
previousbssid,
1);
i = libertas_find_SSID_in_list(adapter,
&adapter->
previousssid,
adapter->
previousbssid,
adapter->mode);
}
if (i < 0) {
/* If the BSSID could not be found, try just the SSID */
i = libertas_find_SSID_in_list(adapter,
&adapter->
previousssid, NULL,
adapter->mode);
}
if (i < 0) {
libertas_send_specific_SSID_scan(priv,
&adapter->
previousssid,
1);
i = libertas_find_SSID_in_list(adapter,
&adapter->
previousssid, NULL,
adapter->mode);
}
if (i >= 0) {
ret =
wlan_associate(priv,
&adapter->
scantable[i]);
}
}
} else if (adapter->mode == IW_MODE_ADHOC) {
ret = libertas_prepare_and_send_command(priv,
cmd_802_11_ad_hoc_start,
0,
cmd_option_waitforrsp,
0, &adapter->previousssid);
}
}
/* else it is connected */
lbs_pr_debug(1, "\nwlanidle is off");
LEAVE();
return ret;
}
/**
* @brief Set Idle On
*
* @param priv A pointer to wlan_private structure
* @return 0 --success, otherwise fail
*/
int libertas_idle_on(wlan_private * priv)
{
wlan_adapter *adapter = priv->adapter;
int ret = 0;
if (adapter->connect_status == libertas_connected) {
if (adapter->mode == IW_MODE_INFRA) {
lbs_pr_debug(1, "Previous SSID = %s\n",
adapter->previousssid.ssid);
memmove(&adapter->previousssid,
&adapter->curbssparams.ssid,
sizeof(struct WLAN_802_11_SSID));
libertas_send_deauth(priv);
} else if (adapter->mode == IW_MODE_ADHOC) {
ret = libertas_stop_adhoc_network(priv);
}
}
lbs_pr_debug(1, "\nwlanidle is on");
return ret;
}
/**
* @brief This function prepares command of authenticate.
*

View File

@ -37,10 +37,6 @@ extern int libertas_ret_80211_disassociate(wlan_private * priv,
extern int libertas_ret_80211_associate(wlan_private * priv,
struct cmd_ds_command *resp);
extern int libertas_idle_on(wlan_private * priv);
extern int libertas_idle_off(wlan_private * priv);
extern int libertas_do_adhocstop_ioctl(wlan_private * priv);
extern int libertas_reassociation_thread(void *data);
struct WLAN_802_11_SSID;

View File

@ -986,136 +986,17 @@ static const struct iw_priv_args wlan_private_args[] = {
/*
* { cmd, set_args, get_args, name }
*/
{
WLANSCAN_TYPE,
IW_PRIV_TYPE_CHAR | 8,
IW_PRIV_TYPE_CHAR | 8,
"scantype"},
{
WLAN_SETINT_GETINT,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
""},
{
WLANNF,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getNF"},
{
WLANRSSI,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getRSSI"},
{
WLANENABLE11D,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"enable11d"},
{
WLANADHOCGRATE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"adhocgrate"},
{
WLAN_SUBCMD_SET_PRESCAN,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"prescan"},
{
WLAN_SETONEINT_GETONEINT,
IW_PRIV_TYPE_INT | 1,
IW_PRIV_TYPE_INT | 1,
""},
{
WLAN_BEACON_INTERVAL,
IW_PRIV_TYPE_INT | 1,
IW_PRIV_TYPE_INT | 1,
"bcninterval"},
{
WLAN_LISTENINTRVL,
IW_PRIV_TYPE_INT | 1,
IW_PRIV_TYPE_INT | 1,
"lolisteninter"},
{
WLAN_TXCONTROL,
IW_PRIV_TYPE_INT | 1,
IW_PRIV_TYPE_INT | 1,
"txcontrol"},
{
WLAN_NULLPKTINTERVAL,
IW_PRIV_TYPE_INT | 1,
IW_PRIV_TYPE_INT | 1,
"psnullinterval"},
/* Using iwpriv sub-command feature */
{
WLAN_SETONEINT_GETNONE, /* IOCTL: 24 */
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
""},
{
WLAN_SUBCMD_SETRXANTENNA,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setrxant"},
{
WLAN_SUBCMD_SETTXANTENNA,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"settxant"},
{
WLANSETENCRYPTIONMODE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"encryptionmode",
},
{
WLANSETREGION,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setregioncode"},
{
WLAN_SET_LISTEN_INTERVAL,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setlisteninter"},
{
WLAN_SET_MULTIPLE_DTIM,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setmultipledtim"},
{
WLAN_SET_ATIM_WINDOW,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"atimwindow"},
{
WLANSETBCNAVG,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setbcnavg"},
{
WLANSETDATAAVG,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"setdataavg"},
{
WLAN_SET_LINKMODE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"linkmode"},
{
WLAN_SET_RADIOMODE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"radiomode"},
{
WLAN_SET_DEBUGMODE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
IW_PRIV_TYPE_NONE,
"debugmode"},
{
WLAN_SUBCMD_MESH_SET_TTL,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
@ -1131,41 +1012,6 @@ static const struct iw_priv_args wlan_private_args[] = {
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getregioncode"},
{
WLAN_GET_LISTEN_INTERVAL,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getlisteninter"},
{
WLAN_GET_MULTIPLE_DTIM,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getmultipledtim"},
{
WLAN_GET_TX_RATE,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"gettxrate"},
{
WLANGETBCNAVG,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"getbcnavg"},
{
WLAN_GET_LINKMODE,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"get_linkmode"},
{
WLAN_GET_RADIOMODE,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"get_radiomode"},
{
WLAN_GET_DEBUGMODE,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"get_debugmode"},
{
WLAN_SUBCMD_FWT_CLEANUP,
IW_PRIV_TYPE_NONE,
@ -1181,61 +1027,11 @@ static const struct iw_priv_args wlan_private_args[] = {
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_INT | IW_PRIV_SIZE_FIXED | 1,
"mesh_get_ttl"},
{
WLAN_SETNONE_GETTWELVE_CHAR,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | 12,
""},
{
WLAN_SUBCMD_GETRXANTENNA,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | 12,
"getrxant"},
{
WLAN_SUBCMD_GETTXANTENNA,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | 12,
"gettxant"},
{
WLAN_GET_TSF,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | 12,
"gettsf"},
{
WLAN_SETNONE_GETNONE,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
""},
{
WLANDEAUTH,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"deauth"},
{
WLANADHOCSTOP,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"adhocstop"},
{
WLANRADIOON,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"radioon"},
{
WLANRADIOOFF,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"radiooff"},
{
WLANWLANIDLEON,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"wlanidle-on"},
{
WLANWLANIDLEOFF,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_NONE,
"wlanidle-off"},
{
WLAN_SUBCMD_FWT_RESET,
IW_PRIV_TYPE_NONE,
@ -1298,86 +1094,16 @@ static const struct iw_priv_args wlan_private_args[] = {
IW_PRIV_TYPE_CHAR | 128,
IW_PRIV_TYPE_CHAR | 128,
"fwt_list_route"},
{
WLANSCAN_MODE,
IW_PRIV_TYPE_CHAR | 128,
IW_PRIV_TYPE_CHAR | 128,
"scanmode"},
{
WLAN_GET_ADHOC_STATUS,
IW_PRIV_TYPE_CHAR | 128,
IW_PRIV_TYPE_CHAR | 128,
"getadhocstatus"},
{
WLAN_SETNONE_GETWORDCHAR,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | 128,
""},
{
WLANGETLOG,
IW_PRIV_TYPE_NONE,
IW_PRIV_TYPE_CHAR | GETLOG_BUFSIZE,
"getlog"},
{
WLAN_SET_GET_SIXTEEN_INT,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
""},
{
WLAN_TPCCFG,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"tpccfg"},
{
WLAN_POWERCFG,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"powercfg"},
{
WLAN_AUTO_FREQ_SET,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"setafc"},
{
WLAN_AUTO_FREQ_GET,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"getafc"},
{
WLAN_SCANPROBES,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"scanprobes"},
{
WLAN_LED_GPIO_CTRL,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"ledgpio"},
{
WLAN_ADAPT_RATESET,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"rateadapt"},
{
WLAN_INACTIVITY_TIMEOUT,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"inactivityto"},
{
WLANSNR,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"getSNR"},
{
WLAN_GET_RATE,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"getrate"},
{
WLAN_GET_RXINFO,
IW_PRIV_TYPE_INT | 16,
IW_PRIV_TYPE_INT | 16,
"getrxinfo"},
};
static struct iw_statistics *wlan_get_wireless_stats(struct net_device *dev)

View File

@ -10,88 +10,22 @@
/** PRIVATE CMD ID */
#define WLANIOCTL SIOCIWFIRSTPRIV
#define WLANSETWPAIE (WLANIOCTL + 0)
#define WLAN_SETINT_GETINT (WLANIOCTL + 7)
#define WLANNF 1
#define WLANRSSI 2
#define WLANENABLE11D 5
#define WLANADHOCGRATE 6
#define WLAN_SUBCMD_SET_PRESCAN 11
#define WLAN_SETNONE_GETNONE (WLANIOCTL + 8)
#define WLANDEAUTH 1
#define WLANRADIOON 2
#define WLANRADIOOFF 3
#define WLANREMOVEADHOCAES 4
#define WLANADHOCSTOP 5
#define WLANCIPHERTEST 6
#define WLANCRYPTOTEST 7
#define WLANWLANIDLEON 10
#define WLANWLANIDLEOFF 11
#define WLAN_SUBCMD_BT_RESET 13
#define WLAN_SUBCMD_FWT_RESET 14
#define WLANGETLOG (WLANIOCTL + 9)
#define GETLOG_BUFSIZE 300
#define WLANSCAN_TYPE (WLANIOCTL + 11)
#define WLAN_SETNONE_GETONEINT (WLANIOCTL + 15)
#define WLANGETREGION 1
#define WLAN_GET_LISTEN_INTERVAL 2
#define WLAN_GET_MULTIPLE_DTIM 3
#define WLAN_GET_TX_RATE 4
#define WLANGETBCNAVG 5
#define WLAN_GET_LINKMODE 6
#define WLAN_GET_RADIOMODE 7
#define WLAN_GET_DEBUGMODE 8
#define WLAN_SUBCMD_FWT_CLEANUP 15
#define WLAN_SUBCMD_FWT_TIME 16
#define WLAN_SUBCMD_MESH_GET_TTL 17
#define WLANREGCFRDWR (WLANIOCTL + 18)
#define WLAN_SETNONE_GETTWELVE_CHAR (WLANIOCTL + 19)
#define WLAN_SUBCMD_GETRXANTENNA 1
#define WLAN_SUBCMD_GETTXANTENNA 2
#define WLAN_GET_TSF 3
#define WLAN_SETNONE_GETWORDCHAR (WLANIOCTL + 21)
#define WLANGETADHOCAES 1
#define WLAN_SETONEINT_GETONEINT (WLANIOCTL + 23)
#define WLAN_BEACON_INTERVAL 1
#define WLAN_LISTENINTRVL 4
#define WLAN_TXCONTROL 6
#define WLAN_NULLPKTINTERVAL 7
#define WLAN_SETONEINT_GETNONE (WLANIOCTL + 24)
#define WLAN_SUBCMD_SETRXANTENNA 1
#define WLAN_SUBCMD_SETTXANTENNA 2
#define WLANSETAUTHALG 5
#define WLANSET8021XAUTHALG 6
#define WLANSETENCRYPTIONMODE 7
#define WLANSETREGION 8
#define WLAN_SET_LISTEN_INTERVAL 9
#define WLAN_SET_MULTIPLE_DTIM 10
#define WLAN_SET_ATIM_WINDOW 11
#define WLANSETBCNAVG 13
#define WLANSETDATAAVG 14
#define WLAN_SET_LINKMODE 15
#define WLAN_SET_RADIOMODE 16
#define WLAN_SET_DEBUGMODE 17
#define WLAN_SUBCMD_MESH_SET_TTL 18
#define WLAN_SET128CHAR_GET128CHAR (WLANIOCTL + 25)
#define WLANSCAN_MODE 6
#define WLAN_GET_ADHOC_STATUS 9
#define WLAN_SUBCMD_BT_ADD 18
#define WLAN_SUBCMD_BT_DEL 19
#define WLAN_SUBCMD_BT_LIST 20
@ -103,27 +37,8 @@
#define WLAN_SUBCMD_FWT_LIST_ROUTE 26
#define WLAN_SET_GET_SIXTEEN_INT (WLANIOCTL + 29)
#define WLAN_TPCCFG 1
#define WLAN_POWERCFG 2
#define WLAN_AUTO_FREQ_SET 3
#define WLAN_AUTO_FREQ_GET 4
#define WLAN_LED_GPIO_CTRL 5
#define WLAN_SCANPROBES 6
#define WLAN_ADAPT_RATESET 8
#define WLAN_INACTIVITY_TIMEOUT 9
#define WLANSNR 10
#define WLAN_GET_RATE 11
#define WLAN_GET_RXINFO 12
#define WLANCMD52RDWR (WLANIOCTL + 30)
#define WLANCMD53RDWR (WLANIOCTL + 31)
#define CMD53BUFLEN 32
#define REG_MAC 0x19
#define REG_BBP 0x1a
#define REG_RF 0x1b
#define REG_EEPROM 0x59
#define WLAN_LINKMODE_802_3 0
#define WLAN_LINKMODE_802_11 2
#define WLAN_RADIOMODE_NONE 0