diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt new file mode 100644 index 000000000000..3d6d5fa0c4d5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -0,0 +1,207 @@ +* Allwinner sun8i GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: +- compatible: must be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun8i-v3s-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- interrupts: interrupt for the device +- interrupt-names: must be "macirq" +- clocks: A phandle to the reference clock for this device +- clock-names: must be "stmmaceth" +- resets: A phandle to the reset control for this device +- reset-names: must be "stmmaceth" +- phy-mode: See ethernet.txt +- phy-handle: See ethernet.txt +- #address-cells: shall be 1 +- #size-cells: shall be 0 +- syscon: A phandle to the syscon of the SoC with one of the following + compatible string: + - allwinner,sun8i-h3-system-controller + - allwinner,sun8i-v3s-system-controller + - allwinner,sun50i-a64-system-controller + - allwinner,sun8i-a83t-system-controller + +Optional properties: +- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0) +- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0) +Both delay properties need to be a multiple of 100. They control the delay for +external PHY. + +Optional properties for the following compatibles: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Required child node of emac: +- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio" + +Required properties of the mdio node: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +The device node referenced by "phy" or "phy-handle" must be a child node +of the mdio node. See phy.txt for the generic PHY bindings. + +The following compatibles require that the emac node have a mdio-mux child +node called "mdio-mux": + - "allwinner,sun8i-h3-emac" + - "allwinner,sun8i-v3s-emac": +Required properties for the mdio-mux node: + - compatible = "allwinner,sun8i-h3-mdio-mux" + - mdio-parent-bus: a phandle to EMAC mdio + - one child mdio for the integrated mdio with the compatible + "allwinner,sun8i-h3-mdio-internal" + - one child mdio for the external mdio if present (V3s have none) +Required properties for the mdio-mux children node: + - reg: 1 for internal MDIO bus, 2 for external MDIO bus + +The following compatibles require a PHY node representing the integrated +PHY, under the integrated MDIO bus node if an mdio-mux node is used: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": + +Additional information regarding generic multiplexer properties can be found +at Documentation/devicetree/bindings/net/mdio-mux.txt + +Required properties of the integrated phy node: +- clocks: a phandle to the reference clock for the EPHY +- resets: a phandle to the reset control for the EPHY +- Must be a child of the integrated mdio + +Example with integrated PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = ; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + phy-is-integrated; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +Example with external PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = ; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }: + }; +}; + +Example with SoC without integrated PHY + +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = ; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/axp81x.dtsi b/arch/arm/boot/dts/axp81x.dtsi new file mode 100644 index 000000000000..73b761f850c5 --- /dev/null +++ b/arch/arm/boot/dts/axp81x.dtsi @@ -0,0 +1,139 @@ +/* + * Copyright 2017 Chen-Yu Tsai + * + * Chen-Yu Tsai + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/* AXP813/818 Integrated Power Management Chip */ + +&axp81x { + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + /* Default work frequency for buck regulators */ + x-powers,dcdc-freq = <3000>; + + reg_dcdc1: dcdc1 { + }; + + reg_dcdc2: dcdc2 { + }; + + reg_dcdc3: dcdc3 { + }; + + reg_dcdc4: dcdc4 { + }; + + reg_dcdc5: dcdc5 { + }; + + reg_dcdc6: dcdc6 { + }; + + reg_dcdc7: dcdc7 { + }; + + reg_aldo1: aldo1 { + }; + + reg_aldo2: aldo2 { + }; + + reg_aldo3: aldo3 { + }; + + reg_dldo1: dldo1 { + }; + + reg_dldo2: dldo2 { + }; + + reg_dldo3: dldo3 { + }; + + reg_dldo4: dldo4 { + }; + + reg_eldo1: eldo1 { + }; + + reg_eldo2: eldo2 { + }; + + reg_eldo3: eldo3 { + }; + + reg_fldo1: fldo1 { + }; + + reg_fldo2: fldo2 { + }; + + reg_fldo3: fldo3 { + }; + + reg_ldo_io0: ldo-io0 { + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_ldo_io1: ldo-io1 { + /* Disable by default to avoid conflicts with GPIO */ + status = "disabled"; + }; + + reg_rtc_ldo: rtc-ldo { + /* RTC_LDO is a fixed, always-on regulator */ + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_sw: sw { + }; + + reg_drivevbus: drivevbus { + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts index 1f0d60afb25b..5091cecbcd1e 100644 --- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts +++ b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts @@ -43,7 +43,8 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" + +#include / { model = "Allwinner A83T H8Homlet Proto Dev Board v2.0"; @@ -56,6 +57,26 @@ chosen { stdout-path = "serial0:115200n8"; }; + + reg_usb0_vbus: reg-usb0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; }; &ehci0 { @@ -65,7 +86,7 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ bus-width = <4>; cd-inverted; @@ -75,7 +96,8 @@ &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v0>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -86,16 +108,6 @@ status = "okay"; }; -®_usb0_vbus { - gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ - status = "okay"; -}; - -®_usb1_vbus { - gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ - status = "okay"; -}; - &r_rsb { status = "okay"; @@ -104,6 +116,8 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; }; ac100: codec@e89 { @@ -131,6 +145,113 @@ }; }; +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-ephy"; +}; + +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + regulator-name = "vcc-wifi"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts index 2bafd7e99ef7..c606af3dbfed 100644 --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts @@ -44,7 +44,6 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" #include @@ -59,6 +58,27 @@ chosen { stdout-path = "serial0:115200n8"; }; + + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -71,17 +91,35 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ cd-inverted; status = "okay"; }; +&mmc1 { + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -96,6 +134,10 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + fldoin-supply = <®_dcdc5>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -123,17 +165,126 @@ }; }; -®_usb1_vbus { - gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* schematics says 3.1V but FEX file says 3.3V */ + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + /* + * This powers both the WiFi/BT module's main power, I/O supply, + * and external pull-ups on all the data lines. It should be set + * to the same voltage as the I/O supply (DCDC1 in this case) to + * avoid any leakage or mismatch. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pd"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; }; -®_vcc3v0 { - status = "disabled"; +®_fldo1 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; }; -®_vcc5v0 { - status = "disabled"; +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + /* + * The PHY requires 20ms after all voltages + * are applied until core logic is ready and + * 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC + * ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-name = "vcc-ephy"; }; &uart0 { diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts index 716a205c6dbb..7f0a3f6d0cf2 100644 --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts @@ -44,7 +44,6 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" #include @@ -95,6 +94,26 @@ refclk-frequency = <19200000>; }; + reg_usb1_vbus: reg-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */ + }; + + reg_usb2_vbus: reg-usb2-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + sound { compatible = "simple-audio-card"; simple-audio-card,name = "On-board SPDIF"; @@ -112,6 +131,17 @@ #sound-dai-cells = <0>; compatible = "linux,spdif-dit"; }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + clocks = <&ac100_rtc 1>; + clock-names = "ext_clock"; + /* The WiFi low power clock must be 32768 Hz */ + assigned-clocks = <&ac100_rtc 1>; + assigned-clock-rates = <32768>; + /* enables internal regulator and de-asserts reset */ + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ + }; }; &ehci0 { @@ -127,17 +157,26 @@ &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */ cd-inverted; status = "okay"; }; +&mmc1 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_sw>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_emmc_pins>; - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -152,6 +191,9 @@ reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + eldoin-supply = <®_dcdc1>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -179,22 +221,143 @@ }; }; -®_usb1_vbus { - gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */ +#include "axp81x.dtsi" + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1v8"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dram-pll"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_dcdc1 { + /* + * The schematics say this should be 3.3V, but the FEX file says + * it should be 3V. The latter makes sense, as the WiFi module's + * I/O is indirectly powered from DCDC1, through SW. It is rated + * at 2.98V maximum. + */ + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpua"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-name = "vdd-sys"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "dp-pwr"; +}; + +®_dldo3 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "ephy-io"; +}; + +®_dldo4 { + /* + * The PHY requires 20ms after all voltages are applied until core + * logic is ready and 30ms after the reset pin is de-asserted. + * Set a 100ms delay to account for PMIC ramp time and board traces. + */ + regulator-enable-ramp-delay = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ephy"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; status = "okay"; }; -®_usb2_vbus { - gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ - status = "okay"; +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-1"; }; -®_vcc3v0 { - status = "disabled"; +®_eldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "dp-bridge-2"; }; -®_vcc5v0 { - status = "disabled"; +®_fldo1 { + /* TODO should be handled by USB PHY */ + regulator-always-on; + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vdd12-hsic"; +}; + +®_fldo2 { + /* + * Despite the embedded CPUs core not being used in any way, + * this must remain on or the system will hang. + */ + regulator-always-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +®_sw { + regulator-name = "vcc-wifi-io"; }; &spdif { diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts index 723641f56a74..98715538932f 100644 --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts @@ -43,7 +43,8 @@ /dts-v1/; #include "sun8i-a83t.dtsi" -#include "sunxi-common-regulators.dtsi" + +#include / { model = "TBS A711 Tablet"; @@ -105,7 +106,7 @@ }; &mmc0 { - vmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; @@ -115,10 +116,8 @@ &mmc1 { mmc-pwrseq = <&wifi_pwrseq>; bus-width = <4>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dldo1>; + vqmmc-supply = <®_dldo1>; non-removable; wakeup-source; status = "okay"; @@ -135,8 +134,8 @@ &mmc2 { pinctrl-0 = <&mmc2_8bit_emmc_pins>; pinctrl-names = "default"; - vmmc-supply = <®_vcc3v3>; - vqmmc-supply = <®_vcc3v3>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; bus-width = <8>; non-removable; cap-mmc-hw-reset; @@ -146,11 +145,12 @@ &r_rsb { status = "okay"; - axp813: pmic@3a3 { - compatible = "x-powers,axp813"; + axp81x: pmic@3a3 { reg = <0x3a3>; interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + swin-supply = <®_dcdc1>; + x-powers,drive-vbus-en; }; ac100: codec@e89 { @@ -179,6 +179,149 @@ }; +#include "axp81x.dtsi" + +®_aldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-1.8"; +}; + +®_aldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-name = "vdd-drampll"; +}; + +®_aldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-name = "avcc"; +}; + +®_dcdc1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + regulator-name = "vcc-io"; +}; + +®_dcdc2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpu-A"; +}; + +®_dcdc3 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpu-B"; +}; + +®_dcdc4 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-gpu"; +}; + +®_dcdc5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-name = "vcc-dram"; +}; + +®_dcdc6 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-wifi-io"; +}; + +®_dldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <4200000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "avdd-csi"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_eldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi-r"; +}; + +®_eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dsi"; +}; + +®_eldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-name = "dvdd-csi-f"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-hsic"; +}; + +®_fldo2 { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-name = "vdd-cpus"; +}; + +®_ldo_io0 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-ctp"; + status = "okay"; +}; + +®_ldo_io1 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-vb"; + status = "okay"; +}; + +®_sw { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-name = "vcc-lcd"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; @@ -192,8 +335,15 @@ status = "okay"; }; -&usbphy { - usb1_vbus_supply = <®_vcc5v0>; - usb2_vbus_supply = <®_vcc5v0>; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus_supply = <®_vmain>; + usb2_vbus_supply = <®_vmain>; status = "okay"; }; diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index ce6e887c8938..19acae1b4089 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -212,6 +212,8 @@ resets = <&ccu RST_BUS_MMC1>; reset-names = "ahb"; interrupts = ; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts index b1502df7b509..6713d0f2b3f4 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts @@ -56,6 +56,8 @@ aliases { serial0 = &uart0; + /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ + ethernet0 = &emac; ethernet1 = &xr819; }; @@ -102,6 +104,13 @@ status = "okay"; }; +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts index e1dba9ffa94b..f2292deaa590 100644 --- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts @@ -52,6 +52,7 @@ compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3"; aliases { + ethernet0 = &emac; serial0 = &uart0; serial1 = &uart1; }; @@ -111,6 +112,24 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + allwinner,leds-active-low; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts index 73766d38ee6c..0a8b79cf5954 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts @@ -51,6 +51,16 @@ ethernet1 = &sdio_wifi; }; + reg_gmac_3v3: gmac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "gmac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <100000>; + enable-active-high; + gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; pinctrl-names = "default"; @@ -66,6 +76,25 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + allwinner,leds-active-low; + + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <7>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts index 8d2cc6e9a03f..78f6c24952dd 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts @@ -46,3 +46,10 @@ model = "FriendlyARM NanoPi NEO"; compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3"; }; + +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts index 1bf51802f5aa..b20be95b49d5 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts @@ -54,6 +54,7 @@ aliases { serial0 = &uart0; /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */ + ethernet0 = &emac; ethernet1 = &rtl8189; }; @@ -117,6 +118,13 @@ status = "okay"; }; +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts index a1c6ff6fd05d..82e5d28cd698 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts @@ -52,6 +52,7 @@ compatible = "xunlong,orangepi-one", "allwinner,sun8i-h3"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -97,6 +98,13 @@ status = "okay"; }; +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts index 8b93f5c781a7..a10281b455f5 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts @@ -53,6 +53,11 @@ }; }; +&emac { + /* LEDs changed to active high on the plus */ + /delete-property/ allwinner,leds-active-low; +}; + &mmc1 { pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts index ea4e0029c0d4..d22546df1b82 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts @@ -52,6 +52,7 @@ compatible = "xunlong,orangepi-pc", "allwinner,sun8i-h3"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -113,6 +114,13 @@ status = "okay"; }; +&emac { + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + status = "okay"; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts index 72ca01b93f1b..cbc499b04de4 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts @@ -47,6 +47,10 @@ model = "Xunlong Orange Pi Plus / Plus 2"; compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3"; + aliases { + ethernet0 = &emac; + }; + reg_gmac_3v3: gmac-3v3 { compatible = "regulator-fixed"; regulator-name = "gmac-3v3"; @@ -74,6 +78,24 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + allwinner,leds-active-low; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; + &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_8bit_pins>; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts index 97920b12a944..6dbf7b2e0c13 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts @@ -61,3 +61,19 @@ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ }; }; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index d7a71e726a9f..8d40c00d64bb 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -396,6 +396,55 @@ clocks = <&osc24M>; }; + emac: ethernet@1c30000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c30000 0x10000>; + interrupts = ; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + /* Only one MDIO is usable at the time */ + internal_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + int_mii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + + external_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + }; + spi0: spi@1c68000 { compatible = "allwinner,sun8i-h3-spi"; reg = <0x01c68000 0x1000>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts index 1c2387bd5df6..6eb8092d8e57 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts @@ -50,6 +50,7 @@ compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -108,6 +109,22 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@7 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <7>; + }; +}; + &mmc0 { pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index 4f77c8470f6c..a0ca925175aa 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -59,6 +59,7 @@ }; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -136,6 +137,22 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts index 6be06873e5af..b47790650144 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts @@ -54,6 +54,7 @@ compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5"; aliases { + ethernet0 = &emac; serial0 = &uart0; }; @@ -143,6 +144,22 @@ status = "okay"; }; +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&emac_rgmii_pins>; + phy-supply = <®_gmac_3v3>; + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&external_mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + &ir { pinctrl-names = "default"; pinctrl-0 = <&ir_pins_a>;