linux/drivers/i2c/busses/i2c-tegra.c

1762 lines
49 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
/*
* drivers/i2c/busses/i2c-tegra.c
*
* Copyright (C) 2010 Google, Inc.
* Author: Colin Cross <ccross@android.com>
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/reset.h>
#define BYTES_PER_FIFO_WORD 4
#define I2C_CNFG 0x000
#define I2C_CNFG_DEBOUNCE_CNT_SHIFT 12
#define I2C_CNFG_PACKET_MODE_EN BIT(10)
#define I2C_CNFG_NEW_MASTER_FSM BIT(11)
#define I2C_CNFG_MULTI_MASTER_MODE BIT(17)
#define I2C_STATUS 0x01C
#define I2C_SL_CNFG 0x020
#define I2C_SL_CNFG_NACK BIT(1)
#define I2C_SL_CNFG_NEWSL BIT(2)
#define I2C_SL_ADDR1 0x02c
i2c: tegra: Assign unused slave address On Tegra, we should always use the "new" I2C slave controller, to avoid issues with the old controller. This was implemented in commit 65a1a0a "i2c: tegra: Enable new slave mode." There is currently no driver for the Tegra I2C slave controller upstream. Additionally, the controller cannot be completely disabled. Instead, we need to: a) Set I2C_SL_CNFG_NACK to make the controller automatically NACK any incoming transactions. b) The controller's definition of NACK isn't identical to the I2C protocol's definition. Specifically, it will perform a standard NACK, but *also* continue to hold the clock line low in expectation of receiving more data. This can hang the bus, or at least cause transaction timeouts, if something starts a transaction that matches the controller's slave address. Since the default address is 0x00, the general call address, this does occur in practice. To avoid this, we explicitly program a slave address that is reserved for future expansion. For current boards, this guarantees the address will never be used. If a future board ever needs to use this address, we can add platform data to determine a board-specific safe address. 0xfc is picked by this patch. This patch is based on a change previously posted by: Wei Ni <wni@nvidia.com> http://www.spinics.net/lists/linux-i2c/msg05437.html In turned based on internal changes by: Bharat Nihalani <bnihalani@nvidia.com> A semantically equivalent change has been contained in the various ChromeOS kernels for a while. I tested this change on top of 3.0-rc2 on Harmony, and interacted with the WM8903 I2C-based audio codec. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-06-06 17:25:19 +00:00
#define I2C_SL_ADDR2 0x030
#define I2C_TX_FIFO 0x050
#define I2C_RX_FIFO 0x054
#define I2C_PACKET_TRANSFER_STATUS 0x058
#define I2C_FIFO_CONTROL 0x05c
#define I2C_FIFO_CONTROL_TX_FLUSH BIT(1)
#define I2C_FIFO_CONTROL_RX_FLUSH BIT(0)
#define I2C_FIFO_CONTROL_TX_TRIG(x) (((x) - 1) << 5)
#define I2C_FIFO_CONTROL_RX_TRIG(x) (((x) - 1) << 2)
#define I2C_FIFO_STATUS 0x060
#define I2C_FIFO_STATUS_TX_MASK 0xF0
#define I2C_FIFO_STATUS_TX_SHIFT 4
#define I2C_FIFO_STATUS_RX_MASK 0x0F
#define I2C_FIFO_STATUS_RX_SHIFT 0
#define I2C_INT_MASK 0x064
#define I2C_INT_STATUS 0x068
#define I2C_INT_BUS_CLR_DONE BIT(11)
#define I2C_INT_PACKET_XFER_COMPLETE BIT(7)
#define I2C_INT_NO_ACK BIT(3)
#define I2C_INT_ARBITRATION_LOST BIT(2)
#define I2C_INT_TX_FIFO_DATA_REQ BIT(1)
#define I2C_INT_RX_FIFO_DATA_REQ BIT(0)
#define I2C_CLK_DIVISOR 0x06c
#define I2C_CLK_DIVISOR_STD_FAST_MODE_SHIFT 16
#define DVC_CTRL_REG1 0x000
#define DVC_CTRL_REG1_INTR_EN BIT(10)
#define DVC_CTRL_REG3 0x008
#define DVC_CTRL_REG3_SW_PROG BIT(26)
#define DVC_CTRL_REG3_I2C_DONE_INTR_EN BIT(30)
#define DVC_STATUS 0x00c
#define DVC_STATUS_I2C_DONE_INTR BIT(30)
#define I2C_ERR_NONE 0x00
#define I2C_ERR_NO_ACK BIT(0)
#define I2C_ERR_ARBITRATION_LOST BIT(1)
#define I2C_ERR_UNKNOWN_INTERRUPT BIT(2)
#define I2C_ERR_RX_BUFFER_OVERFLOW BIT(3)
#define PACKET_HEADER0_HEADER_SIZE_SHIFT 28
#define PACKET_HEADER0_PACKET_ID_SHIFT 16
#define PACKET_HEADER0_CONT_ID_SHIFT 12
#define PACKET_HEADER0_PROTOCOL_I2C BIT(4)
#define I2C_HEADER_CONT_ON_NAK BIT(21)
#define I2C_HEADER_READ BIT(19)
#define I2C_HEADER_10BIT_ADDR BIT(18)
#define I2C_HEADER_IE_ENABLE BIT(17)
#define I2C_HEADER_REPEAT_START BIT(16)
#define I2C_HEADER_CONTINUE_XFER BIT(15)
#define I2C_HEADER_SLAVE_ADDR_SHIFT 1
#define I2C_BUS_CLEAR_CNFG 0x084
#define I2C_BC_SCLK_THRESHOLD 9
#define I2C_BC_SCLK_THRESHOLD_SHIFT 16
#define I2C_BC_STOP_COND BIT(2)
#define I2C_BC_TERMINATE BIT(1)
#define I2C_BC_ENABLE BIT(0)
#define I2C_BUS_CLEAR_STATUS 0x088
#define I2C_BC_STATUS BIT(0)
#define I2C_CONFIG_LOAD 0x08C
#define I2C_MSTR_CONFIG_LOAD BIT(0)
#define I2C_CLKEN_OVERRIDE 0x090
#define I2C_MST_CORE_CLKEN_OVR BIT(0)
#define I2C_CONFIG_LOAD_TIMEOUT 1000000
#define I2C_MST_FIFO_CONTROL 0x0b4
#define I2C_MST_FIFO_CONTROL_RX_FLUSH BIT(0)
#define I2C_MST_FIFO_CONTROL_TX_FLUSH BIT(1)
#define I2C_MST_FIFO_CONTROL_RX_TRIG(x) (((x) - 1) << 4)
#define I2C_MST_FIFO_CONTROL_TX_TRIG(x) (((x) - 1) << 16)
#define I2C_MST_FIFO_STATUS 0x0b8
#define I2C_MST_FIFO_STATUS_RX_MASK 0xff
#define I2C_MST_FIFO_STATUS_RX_SHIFT 0
#define I2C_MST_FIFO_STATUS_TX_MASK 0xff0000
#define I2C_MST_FIFO_STATUS_TX_SHIFT 16
#define I2C_INTERFACE_TIMING_0 0x94
#define I2C_THIGH_SHIFT 8
#define I2C_INTERFACE_TIMING_1 0x98
#define I2C_STANDARD_MODE 100000
#define I2C_FAST_MODE 400000
#define I2C_FAST_PLUS_MODE 1000000
/* Packet header size in bytes */
#define I2C_PACKET_HEADER_SIZE 12
/*
* Upto I2C_PIO_MODE_MAX_LEN bytes, controller will use PIO mode,
* above this, controller will use DMA to fill FIFO.
* MAX PIO len is 20 bytes excluding packet header.
*/
#define I2C_PIO_MODE_MAX_LEN 32
/*
* msg_end_type: The bus control which need to be send at end of transfer.
* @MSG_END_STOP: Send stop pulse at end of transfer.
* @MSG_END_REPEAT_START: Send repeat start at end of transfer.
* @MSG_END_CONTINUE: The following on message is coming and so do not send
* stop or repeat start.
*/
enum msg_end_type {
MSG_END_STOP,
MSG_END_REPEAT_START,
MSG_END_CONTINUE,
};
/**
* struct tegra_i2c_hw_feature : Different HW support on Tegra
* @has_continue_xfer_support: Continue transfer supports.
* @has_per_pkt_xfer_complete_irq: Has enable/disable capability for transfer
* complete interrupt per packet basis.
* @has_single_clk_source: The I2C controller has single clock source. Tegra30
* and earlier SoCs have two clock sources i.e. div-clk and
* fast-clk.
* @has_config_load_reg: Has the config load register to load the new
* configuration.
* @clk_divisor_hs_mode: Clock divisor in HS mode.
* @clk_divisor_std_mode: Clock divisor in standard mode. It is
* applicable if there is no fast clock source i.e. single clock
* source.
* @clk_divisor_fast_mode: Clock divisor in fast mode. It is
* applicable if there is no fast clock source i.e. single clock
* source.
* @clk_divisor_fast_plus_mode: Clock divisor in fast mode plus. It is
* applicable if there is no fast clock source (i.e. single
* clock source).
* @has_multi_master_mode: The I2C controller supports running in single-master
* or multi-master mode.
* @has_slcg_override_reg: The I2C controller supports a register that
* overrides the second level clock gating.
* @has_mst_fifo: The I2C controller contains the new MST FIFO interface that
* provides additional features and allows for longer messages to
* be transferred in one go.
* @quirks: i2c adapter quirks for limiting write/read transfer size and not
* allowing 0 length transfers.
* @supports_bus_clear: Bus Clear support to recover from bus hang during
* SDA stuck low from device for some unknown reasons.
* @has_apb_dma: Support of APBDMA on corresponding Tegra chip.
* @tlow_std_mode: Low period of the clock in standard mode.
* @thigh_std_mode: High period of the clock in standard mode.
* @tlow_fast_fastplus_mode: Low period of the clock in fast/fast-plus modes.
* @thigh_fast_fastplus_mode: High period of the clock in fast/fast-plus modes.
* @setup_hold_time_std_mode: Setup and hold time for start and stop conditions
* in standard mode.
* @setup_hold_time_fast_fast_plus_mode: Setup and hold time for start and stop
* conditions in fast/fast-plus modes.
* @setup_hold_time_hs_mode: Setup and hold time for start and stop conditions
* in HS mode.
* @has_interface_timing_reg: Has interface timing register to program the tuned
* timing settings.
*/
struct tegra_i2c_hw_feature {
bool has_continue_xfer_support;
bool has_per_pkt_xfer_complete_irq;
bool has_single_clk_source;
bool has_config_load_reg;
int clk_divisor_hs_mode;
int clk_divisor_std_mode;
int clk_divisor_fast_mode;
u16 clk_divisor_fast_plus_mode;
bool has_multi_master_mode;
bool has_slcg_override_reg;
bool has_mst_fifo;
const struct i2c_adapter_quirks *quirks;
bool supports_bus_clear;
bool has_apb_dma;
u8 tlow_std_mode;
u8 thigh_std_mode;
u8 tlow_fast_fastplus_mode;
u8 thigh_fast_fastplus_mode;
u32 setup_hold_time_std_mode;
u32 setup_hold_time_fast_fast_plus_mode;
u32 setup_hold_time_hs_mode;
bool has_interface_timing_reg;
};
/**
* struct tegra_i2c_dev - per device I2C context
* @dev: device reference for power management
* @hw: Tegra I2C HW feature
* @adapter: core I2C layer adapter information
* @div_clk: clock reference for div clock of I2C controller
* @fast_clk: clock reference for fast clock of I2C controller
* @rst: reset control for the I2C controller
* @base: ioremapped registers cookie
* @base_phys: physical base address of the I2C controller
* @cont_id: I2C controller ID, used for packet header
* @irq: IRQ number of transfer complete interrupt
* @irq_disabled: used to track whether or not the interrupt is enabled
* @is_dvc: identifies the DVC I2C controller, has a different register layout
* @msg_complete: transfer completion notifier
* @msg_err: error code for completed message
* @msg_buf: pointer to current message data
* @msg_buf_remaining: size of unsent data in the message buffer
* @msg_read: identifies read transfers
* @bus_clk_rate: current I2C bus clock rate
* @clk_divisor_non_hs_mode: clock divider for non-high-speed modes
* @is_multimaster_mode: track if I2C controller is in multi-master mode
* @xfer_lock: lock to serialize transfer submission and processing
* @tx_dma_chan: DMA transmit channel
* @rx_dma_chan: DMA receive channel
* @dma_phys: handle to DMA resources
* @dma_buf: pointer to allocated DMA buffer
* @dma_buf_size: DMA buffer size
* @is_curr_dma_xfer: indicates active DMA transfer
* @dma_complete: DMA completion notifier
*/
struct tegra_i2c_dev {
struct device *dev;
const struct tegra_i2c_hw_feature *hw;
struct i2c_adapter adapter;
struct clk *div_clk;
struct clk *fast_clk;
struct reset_control *rst;
void __iomem *base;
phys_addr_t base_phys;
int cont_id;
int irq;
bool irq_disabled;
int is_dvc;
struct completion msg_complete;
int msg_err;
u8 *msg_buf;
size_t msg_buf_remaining;
int msg_read;
u32 bus_clk_rate;
u16 clk_divisor_non_hs_mode;
bool is_multimaster_mode;
/* xfer_lock: lock to serialize transfer submission and processing */
spinlock_t xfer_lock;
struct dma_chan *tx_dma_chan;
struct dma_chan *rx_dma_chan;
dma_addr_t dma_phys;
u32 *dma_buf;
unsigned int dma_buf_size;
bool is_curr_dma_xfer;
struct completion dma_complete;
};
static void dvc_writel(struct tegra_i2c_dev *i2c_dev, u32 val,
unsigned long reg)
{
writel(val, i2c_dev->base + reg);
}
static u32 dvc_readl(struct tegra_i2c_dev *i2c_dev, unsigned long reg)
{
return readl(i2c_dev->base + reg);
}
/*
* i2c_writel and i2c_readl will offset the register if necessary to talk
* to the I2C block inside the DVC block
*/
static unsigned long tegra_i2c_reg_addr(struct tegra_i2c_dev *i2c_dev,
unsigned long reg)
{
if (i2c_dev->is_dvc)
reg += (reg >= I2C_TX_FIFO) ? 0x10 : 0x40;
return reg;
}
static void i2c_writel(struct tegra_i2c_dev *i2c_dev, u32 val,
unsigned long reg)
{
writel(val, i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
/* Read back register to make sure that register writes completed */
if (reg != I2C_TX_FIFO)
readl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
}
static u32 i2c_readl(struct tegra_i2c_dev *i2c_dev, unsigned long reg)
{
return readl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
}
static void i2c_writesl(struct tegra_i2c_dev *i2c_dev, void *data,
unsigned long reg, int len)
{
writesl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg), data, len);
}
static void i2c_readsl(struct tegra_i2c_dev *i2c_dev, void *data,
unsigned long reg, int len)
{
readsl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg), data, len);
}
static void tegra_i2c_mask_irq(struct tegra_i2c_dev *i2c_dev, u32 mask)
{
u32 int_mask;
int_mask = i2c_readl(i2c_dev, I2C_INT_MASK) & ~mask;
i2c_writel(i2c_dev, int_mask, I2C_INT_MASK);
}
static void tegra_i2c_unmask_irq(struct tegra_i2c_dev *i2c_dev, u32 mask)
{
u32 int_mask;
int_mask = i2c_readl(i2c_dev, I2C_INT_MASK) | mask;
i2c_writel(i2c_dev, int_mask, I2C_INT_MASK);
}
static void tegra_i2c_dma_complete(void *args)
{
struct tegra_i2c_dev *i2c_dev = args;
complete(&i2c_dev->dma_complete);
}
static int tegra_i2c_dma_submit(struct tegra_i2c_dev *i2c_dev, size_t len)
{
struct dma_async_tx_descriptor *dma_desc;
enum dma_transfer_direction dir;
struct dma_chan *chan;
dev_dbg(i2c_dev->dev, "starting DMA for length: %zu\n", len);
reinit_completion(&i2c_dev->dma_complete);
dir = i2c_dev->msg_read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV;
chan = i2c_dev->msg_read ? i2c_dev->rx_dma_chan : i2c_dev->tx_dma_chan;
dma_desc = dmaengine_prep_slave_single(chan, i2c_dev->dma_phys,
len, dir, DMA_PREP_INTERRUPT |
DMA_CTRL_ACK);
if (!dma_desc) {
dev_err(i2c_dev->dev, "failed to get DMA descriptor\n");
return -EINVAL;
}
dma_desc->callback = tegra_i2c_dma_complete;
dma_desc->callback_param = i2c_dev;
dmaengine_submit(dma_desc);
dma_async_issue_pending(chan);
return 0;
}
static void tegra_i2c_release_dma(struct tegra_i2c_dev *i2c_dev)
{
if (i2c_dev->dma_buf) {
dma_free_coherent(i2c_dev->dev, i2c_dev->dma_buf_size,
i2c_dev->dma_buf, i2c_dev->dma_phys);
i2c_dev->dma_buf = NULL;
}
if (i2c_dev->tx_dma_chan) {
dma_release_channel(i2c_dev->tx_dma_chan);
i2c_dev->tx_dma_chan = NULL;
}
if (i2c_dev->rx_dma_chan) {
dma_release_channel(i2c_dev->rx_dma_chan);
i2c_dev->rx_dma_chan = NULL;
}
}
static int tegra_i2c_init_dma(struct tegra_i2c_dev *i2c_dev)
{
struct dma_chan *chan;
u32 *dma_buf;
dma_addr_t dma_phys;
int err;
if (!i2c_dev->hw->has_apb_dma)
return 0;
if (!IS_ENABLED(CONFIG_TEGRA20_APB_DMA)) {
dev_dbg(i2c_dev->dev, "Support for APB DMA not enabled!\n");
return 0;
}
chan = dma_request_slave_channel_reason(i2c_dev->dev, "rx");
if (IS_ERR(chan)) {
err = PTR_ERR(chan);
goto err_out;
}
i2c_dev->rx_dma_chan = chan;
chan = dma_request_slave_channel_reason(i2c_dev->dev, "tx");
if (IS_ERR(chan)) {
err = PTR_ERR(chan);
goto err_out;
}
i2c_dev->tx_dma_chan = chan;
dma_buf = dma_alloc_coherent(i2c_dev->dev, i2c_dev->dma_buf_size,
&dma_phys, GFP_KERNEL | __GFP_NOWARN);
if (!dma_buf) {
dev_err(i2c_dev->dev, "failed to allocate the DMA buffer\n");
err = -ENOMEM;
goto err_out;
}
i2c_dev->dma_buf = dma_buf;
i2c_dev->dma_phys = dma_phys;
return 0;
err_out:
tegra_i2c_release_dma(i2c_dev);
if (err != -EPROBE_DEFER) {
dev_err(i2c_dev->dev, "cannot use DMA: %d\n", err);
dev_err(i2c_dev->dev, "falling back to PIO\n");
return 0;
}
return err;
}
static int tegra_i2c_flush_fifos(struct tegra_i2c_dev *i2c_dev)
{
unsigned long timeout = jiffies + HZ;
unsigned int offset;
u32 mask, val;
if (i2c_dev->hw->has_mst_fifo) {
mask = I2C_MST_FIFO_CONTROL_TX_FLUSH |
I2C_MST_FIFO_CONTROL_RX_FLUSH;
offset = I2C_MST_FIFO_CONTROL;
} else {
mask = I2C_FIFO_CONTROL_TX_FLUSH |
I2C_FIFO_CONTROL_RX_FLUSH;
offset = I2C_FIFO_CONTROL;
}
val = i2c_readl(i2c_dev, offset);
val |= mask;
i2c_writel(i2c_dev, val, offset);
while (i2c_readl(i2c_dev, offset) & mask) {
if (time_after(jiffies, timeout)) {
dev_warn(i2c_dev->dev, "timeout waiting for fifo flush\n");
return -ETIMEDOUT;
}
usleep_range(1000, 2000);
}
return 0;
}
static int tegra_i2c_empty_rx_fifo(struct tegra_i2c_dev *i2c_dev)
{
u32 val;
int rx_fifo_avail;
u8 *buf = i2c_dev->msg_buf;
size_t buf_remaining = i2c_dev->msg_buf_remaining;
int words_to_transfer;
/*
* Catch overflow due to message fully sent
* before the check for RX FIFO availability.
*/
if (WARN_ON_ONCE(!(i2c_dev->msg_buf_remaining)))
return -EINVAL;
if (i2c_dev->hw->has_mst_fifo) {
val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
rx_fifo_avail = (val & I2C_MST_FIFO_STATUS_RX_MASK) >>
I2C_MST_FIFO_STATUS_RX_SHIFT;
} else {
val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
rx_fifo_avail = (val & I2C_FIFO_STATUS_RX_MASK) >>
I2C_FIFO_STATUS_RX_SHIFT;
}
/* Rounds down to not include partial word at the end of buf */
words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
if (words_to_transfer > rx_fifo_avail)
words_to_transfer = rx_fifo_avail;
i2c_readsl(i2c_dev, buf, I2C_RX_FIFO, words_to_transfer);
buf += words_to_transfer * BYTES_PER_FIFO_WORD;
buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
rx_fifo_avail -= words_to_transfer;
/*
* If there is a partial word at the end of buf, handle it manually to
* prevent overwriting past the end of buf
*/
if (rx_fifo_avail > 0 && buf_remaining > 0) {
/*
* buf_remaining > 3 check not needed as rx_fifo_avail == 0
* when (words_to_transfer was > rx_fifo_avail) earlier
* in this function.
*/
val = i2c_readl(i2c_dev, I2C_RX_FIFO);
val = cpu_to_le32(val);
memcpy(buf, &val, buf_remaining);
buf_remaining = 0;
rx_fifo_avail--;
}
/* RX FIFO must be drained, otherwise it's an Overflow case. */
if (WARN_ON_ONCE(rx_fifo_avail))
return -EINVAL;
i2c_dev->msg_buf_remaining = buf_remaining;
i2c_dev->msg_buf = buf;
return 0;
}
static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
{
u32 val;
int tx_fifo_avail;
u8 *buf = i2c_dev->msg_buf;
size_t buf_remaining = i2c_dev->msg_buf_remaining;
int words_to_transfer;
if (i2c_dev->hw->has_mst_fifo) {
val = i2c_readl(i2c_dev, I2C_MST_FIFO_STATUS);
tx_fifo_avail = (val & I2C_MST_FIFO_STATUS_TX_MASK) >>
I2C_MST_FIFO_STATUS_TX_SHIFT;
} else {
val = i2c_readl(i2c_dev, I2C_FIFO_STATUS);
tx_fifo_avail = (val & I2C_FIFO_STATUS_TX_MASK) >>
I2C_FIFO_STATUS_TX_SHIFT;
}
/* Rounds down to not include partial word at the end of buf */
words_to_transfer = buf_remaining / BYTES_PER_FIFO_WORD;
/* It's very common to have < 4 bytes, so optimize that case. */
if (words_to_transfer) {
if (words_to_transfer > tx_fifo_avail)
words_to_transfer = tx_fifo_avail;
/*
* Update state before writing to FIFO. If this casues us
* to finish writing all bytes (AKA buf_remaining goes to 0) we
* have a potential for an interrupt (PACKET_XFER_COMPLETE is
* not maskable). We need to make sure that the isr sees
* buf_remaining as 0 and doesn't call us back re-entrantly.
*/
buf_remaining -= words_to_transfer * BYTES_PER_FIFO_WORD;
tx_fifo_avail -= words_to_transfer;
i2c_dev->msg_buf_remaining = buf_remaining;
i2c_dev->msg_buf = buf +
words_to_transfer * BYTES_PER_FIFO_WORD;
barrier();
i2c_writesl(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
buf += words_to_transfer * BYTES_PER_FIFO_WORD;
}
/*
* If there is a partial word at the end of buf, handle it manually to
* prevent reading past the end of buf, which could cross a page
* boundary and fault.
*/
if (tx_fifo_avail > 0 && buf_remaining > 0) {
/*
* buf_remaining > 3 check not needed as tx_fifo_avail == 0
* when (words_to_transfer was > tx_fifo_avail) earlier
* in this function for non-zero words_to_transfer.
*/
memcpy(&val, buf, buf_remaining);
val = le32_to_cpu(val);
/* Again update before writing to FIFO to make sure isr sees. */
i2c_dev->msg_buf_remaining = 0;
i2c_dev->msg_buf = NULL;
barrier();
i2c_writel(i2c_dev, val, I2C_TX_FIFO);
}
return 0;
}
/*
* One of the Tegra I2C blocks is inside the DVC (Digital Voltage Controller)
* block. This block is identical to the rest of the I2C blocks, except that
* it only supports master mode, it has registers moved around, and it needs
* some extra init to get it into I2C mode. The register moves are handled
* by i2c_readl and i2c_writel
*/
static void tegra_dvc_init(struct tegra_i2c_dev *i2c_dev)
{
u32 val;
val = dvc_readl(i2c_dev, DVC_CTRL_REG3);
val |= DVC_CTRL_REG3_SW_PROG;
val |= DVC_CTRL_REG3_I2C_DONE_INTR_EN;
dvc_writel(i2c_dev, val, DVC_CTRL_REG3);
val = dvc_readl(i2c_dev, DVC_CTRL_REG1);
val |= DVC_CTRL_REG1_INTR_EN;
dvc_writel(i2c_dev, val, DVC_CTRL_REG1);
}
static int __maybe_unused tegra_i2c_runtime_resume(struct device *dev)
{
struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
int ret;
ret = pinctrl_pm_select_default_state(i2c_dev->dev);
if (ret)
return ret;
if (!i2c_dev->hw->has_single_clk_source) {
ret = clk_enable(i2c_dev->fast_clk);
if (ret < 0) {
dev_err(i2c_dev->dev,
"Enabling fast clk failed, err %d\n", ret);
return ret;
}
}
ret = clk_enable(i2c_dev->div_clk);
if (ret < 0) {
dev_err(i2c_dev->dev,
"Enabling div clk failed, err %d\n", ret);
clk_disable(i2c_dev->fast_clk);
return ret;
}
return 0;
}
static int __maybe_unused tegra_i2c_runtime_suspend(struct device *dev)
{
struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
clk_disable(i2c_dev->div_clk);
if (!i2c_dev->hw->has_single_clk_source)
clk_disable(i2c_dev->fast_clk);
return pinctrl_pm_select_idle_state(i2c_dev->dev);
}
static int tegra_i2c_wait_for_config_load(struct tegra_i2c_dev *i2c_dev)
{
unsigned long reg_offset;
void __iomem *addr;
u32 val;
int err;
if (i2c_dev->hw->has_config_load_reg) {
reg_offset = tegra_i2c_reg_addr(i2c_dev, I2C_CONFIG_LOAD);
addr = i2c_dev->base + reg_offset;
i2c_writel(i2c_dev, I2C_MSTR_CONFIG_LOAD, I2C_CONFIG_LOAD);
if (in_interrupt())
err = readl_poll_timeout_atomic(addr, val, val == 0,
1000,
I2C_CONFIG_LOAD_TIMEOUT);
else
err = readl_poll_timeout(addr, val, val == 0, 1000,
I2C_CONFIG_LOAD_TIMEOUT);
if (err) {
dev_warn(i2c_dev->dev,
"timeout waiting for config load\n");
return err;
}
}
return 0;
}
static int tegra_i2c_init(struct tegra_i2c_dev *i2c_dev, bool clk_reinit)
{
u32 val;
int err;
u32 clk_divisor, clk_multiplier;
u32 tsu_thd;
u8 tlow, thigh;
reset_control_assert(i2c_dev->rst);
udelay(2);
reset_control_deassert(i2c_dev->rst);
if (i2c_dev->is_dvc)
tegra_dvc_init(i2c_dev);
val = I2C_CNFG_NEW_MASTER_FSM | I2C_CNFG_PACKET_MODE_EN |
(0x2 << I2C_CNFG_DEBOUNCE_CNT_SHIFT);
if (i2c_dev->hw->has_multi_master_mode)
val |= I2C_CNFG_MULTI_MASTER_MODE;
i2c_writel(i2c_dev, val, I2C_CNFG);
i2c_writel(i2c_dev, 0, I2C_INT_MASK);
/* Make sure clock divisor programmed correctly */
clk_divisor = i2c_dev->hw->clk_divisor_hs_mode;
clk_divisor |= i2c_dev->clk_divisor_non_hs_mode <<
I2C_CLK_DIVISOR_STD_FAST_MODE_SHIFT;
i2c_writel(i2c_dev, clk_divisor, I2C_CLK_DIVISOR);
if (i2c_dev->bus_clk_rate > I2C_STANDARD_MODE &&
i2c_dev->bus_clk_rate <= I2C_FAST_PLUS_MODE) {
tlow = i2c_dev->hw->tlow_fast_fastplus_mode;
thigh = i2c_dev->hw->thigh_fast_fastplus_mode;
tsu_thd = i2c_dev->hw->setup_hold_time_fast_fast_plus_mode;
} else {
tlow = i2c_dev->hw->tlow_std_mode;
thigh = i2c_dev->hw->thigh_std_mode;
tsu_thd = i2c_dev->hw->setup_hold_time_std_mode;
}
if (i2c_dev->hw->has_interface_timing_reg) {
val = (thigh << I2C_THIGH_SHIFT) | tlow;
i2c_writel(i2c_dev, val, I2C_INTERFACE_TIMING_0);
}
/*
* configure setup and hold times only when tsu_thd is non-zero.
* otherwise, preserve the chip default values
*/
if (i2c_dev->hw->has_interface_timing_reg && tsu_thd)
i2c_writel(i2c_dev, tsu_thd, I2C_INTERFACE_TIMING_1);
if (!clk_reinit) {
clk_multiplier = (tlow + thigh + 2);
clk_multiplier *= (i2c_dev->clk_divisor_non_hs_mode + 1);
err = clk_set_rate(i2c_dev->div_clk,
i2c_dev->bus_clk_rate * clk_multiplier);
if (err) {
dev_err(i2c_dev->dev,
"failed changing clock rate: %d\n", err);
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
return err;
}
}
if (!i2c_dev->is_dvc) {
u32 sl_cfg = i2c_readl(i2c_dev, I2C_SL_CNFG);
i2c: tegra: Assign unused slave address On Tegra, we should always use the "new" I2C slave controller, to avoid issues with the old controller. This was implemented in commit 65a1a0a "i2c: tegra: Enable new slave mode." There is currently no driver for the Tegra I2C slave controller upstream. Additionally, the controller cannot be completely disabled. Instead, we need to: a) Set I2C_SL_CNFG_NACK to make the controller automatically NACK any incoming transactions. b) The controller's definition of NACK isn't identical to the I2C protocol's definition. Specifically, it will perform a standard NACK, but *also* continue to hold the clock line low in expectation of receiving more data. This can hang the bus, or at least cause transaction timeouts, if something starts a transaction that matches the controller's slave address. Since the default address is 0x00, the general call address, this does occur in practice. To avoid this, we explicitly program a slave address that is reserved for future expansion. For current boards, this guarantees the address will never be used. If a future board ever needs to use this address, we can add platform data to determine a board-specific safe address. 0xfc is picked by this patch. This patch is based on a change previously posted by: Wei Ni <wni@nvidia.com> http://www.spinics.net/lists/linux-i2c/msg05437.html In turned based on internal changes by: Bharat Nihalani <bnihalani@nvidia.com> A semantically equivalent change has been contained in the various ChromeOS kernels for a while. I tested this change on top of 3.0-rc2 on Harmony, and interacted with the WM8903 I2C-based audio codec. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-06-06 17:25:19 +00:00
sl_cfg |= I2C_SL_CNFG_NACK | I2C_SL_CNFG_NEWSL;
i2c_writel(i2c_dev, sl_cfg, I2C_SL_CNFG);
i2c_writel(i2c_dev, 0xfc, I2C_SL_ADDR1);
i2c_writel(i2c_dev, 0x00, I2C_SL_ADDR2);
}
err = tegra_i2c_flush_fifos(i2c_dev);
if (err)
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
return err;
if (i2c_dev->is_multimaster_mode && i2c_dev->hw->has_slcg_override_reg)
i2c_writel(i2c_dev, I2C_MST_CORE_CLKEN_OVR, I2C_CLKEN_OVERRIDE);
err = tegra_i2c_wait_for_config_load(i2c_dev);
if (err)
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
return err;
if (i2c_dev->irq_disabled) {
i2c_dev->irq_disabled = false;
enable_irq(i2c_dev->irq);
}
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
return 0;
}
static int tegra_i2c_disable_packet_mode(struct tegra_i2c_dev *i2c_dev)
{
u32 cnfg;
/*
* NACK interrupt is generated before the I2C controller generates
* the STOP condition on the bus. So wait for 2 clock periods
* before disabling the controller so that the STOP condition has
* been delivered properly.
*/
udelay(DIV_ROUND_UP(2 * 1000000, i2c_dev->bus_clk_rate));
cnfg = i2c_readl(i2c_dev, I2C_CNFG);
if (cnfg & I2C_CNFG_PACKET_MODE_EN)
i2c_writel(i2c_dev, cnfg & ~I2C_CNFG_PACKET_MODE_EN, I2C_CNFG);
return tegra_i2c_wait_for_config_load(i2c_dev);
}
static irqreturn_t tegra_i2c_isr(int irq, void *dev_id)
{
u32 status;
const u32 status_err = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST;
struct tegra_i2c_dev *i2c_dev = dev_id;
status = i2c_readl(i2c_dev, I2C_INT_STATUS);
spin_lock(&i2c_dev->xfer_lock);
if (status == 0) {
dev_warn(i2c_dev->dev, "irq status 0 %08x %08x %08x\n",
i2c_readl(i2c_dev, I2C_PACKET_TRANSFER_STATUS),
i2c_readl(i2c_dev, I2C_STATUS),
i2c_readl(i2c_dev, I2C_CNFG));
i2c_dev->msg_err |= I2C_ERR_UNKNOWN_INTERRUPT;
if (!i2c_dev->irq_disabled) {
disable_irq_nosync(i2c_dev->irq);
i2c_dev->irq_disabled = true;
}
goto err;
}
if (unlikely(status & status_err)) {
tegra_i2c_disable_packet_mode(i2c_dev);
if (status & I2C_INT_NO_ACK)
i2c_dev->msg_err |= I2C_ERR_NO_ACK;
if (status & I2C_INT_ARBITRATION_LOST)
i2c_dev->msg_err |= I2C_ERR_ARBITRATION_LOST;
goto err;
}
/*
* I2C transfer is terminated during the bus clear so skip
* processing the other interrupts.
*/
if (i2c_dev->hw->supports_bus_clear && (status & I2C_INT_BUS_CLR_DONE))
goto err;
if (!i2c_dev->is_curr_dma_xfer) {
if (i2c_dev->msg_read && (status & I2C_INT_RX_FIFO_DATA_REQ)) {
if (tegra_i2c_empty_rx_fifo(i2c_dev)) {
/*
* Overflow error condition: message fully sent,
* with no XFER_COMPLETE interrupt but hardware
* asks to transfer more.
*/
i2c_dev->msg_err |= I2C_ERR_RX_BUFFER_OVERFLOW;
goto err;
}
}
if (!i2c_dev->msg_read && (status & I2C_INT_TX_FIFO_DATA_REQ)) {
if (i2c_dev->msg_buf_remaining)
tegra_i2c_fill_tx_fifo(i2c_dev);
else
tegra_i2c_mask_irq(i2c_dev,
I2C_INT_TX_FIFO_DATA_REQ);
}
}
i2c_writel(i2c_dev, status, I2C_INT_STATUS);
if (i2c_dev->is_dvc)
dvc_writel(i2c_dev, DVC_STATUS_I2C_DONE_INTR, DVC_STATUS);
/*
* During message read XFER_COMPLETE interrupt is triggered prior to
* DMA completion and during message write XFER_COMPLETE interrupt is
* triggered after DMA completion.
* PACKETS_XFER_COMPLETE indicates completion of all bytes of transfer.
* so forcing msg_buf_remaining to 0 in DMA mode.
*/
if (status & I2C_INT_PACKET_XFER_COMPLETE) {
if (i2c_dev->is_curr_dma_xfer)
i2c_dev->msg_buf_remaining = 0;
/*
* Underflow error condition: XFER_COMPLETE before message
* fully sent.
*/
if (WARN_ON_ONCE(i2c_dev->msg_buf_remaining)) {
i2c_dev->msg_err |= I2C_ERR_UNKNOWN_INTERRUPT;
goto err;
}
complete(&i2c_dev->msg_complete);
}
goto done;
err:
/* An error occurred, mask all interrupts */
tegra_i2c_mask_irq(i2c_dev, I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST |
I2C_INT_PACKET_XFER_COMPLETE | I2C_INT_TX_FIFO_DATA_REQ |
I2C_INT_RX_FIFO_DATA_REQ);
if (i2c_dev->hw->supports_bus_clear)
tegra_i2c_mask_irq(i2c_dev, I2C_INT_BUS_CLR_DONE);
i2c_writel(i2c_dev, status, I2C_INT_STATUS);
if (i2c_dev->is_dvc)
dvc_writel(i2c_dev, DVC_STATUS_I2C_DONE_INTR, DVC_STATUS);
if (i2c_dev->is_curr_dma_xfer) {
if (i2c_dev->msg_read)
dmaengine_terminate_async(i2c_dev->rx_dma_chan);
else
dmaengine_terminate_async(i2c_dev->tx_dma_chan);
complete(&i2c_dev->dma_complete);
}
complete(&i2c_dev->msg_complete);
done:
spin_unlock(&i2c_dev->xfer_lock);
return IRQ_HANDLED;
}
static void tegra_i2c_config_fifo_trig(struct tegra_i2c_dev *i2c_dev,
size_t len)
{
u32 val, reg;
u8 dma_burst;
struct dma_slave_config slv_config = {0};
struct dma_chan *chan;
int ret;
unsigned long reg_offset;
if (i2c_dev->hw->has_mst_fifo)
reg = I2C_MST_FIFO_CONTROL;
else
reg = I2C_FIFO_CONTROL;
if (i2c_dev->is_curr_dma_xfer) {
if (len & 0xF)
dma_burst = 1;
else if (len & 0x10)
dma_burst = 4;
else
dma_burst = 8;
if (i2c_dev->msg_read) {
chan = i2c_dev->rx_dma_chan;
reg_offset = tegra_i2c_reg_addr(i2c_dev, I2C_RX_FIFO);
slv_config.src_addr = i2c_dev->base_phys + reg_offset;
slv_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
slv_config.src_maxburst = dma_burst;
if (i2c_dev->hw->has_mst_fifo)
val = I2C_MST_FIFO_CONTROL_RX_TRIG(dma_burst);
else
val = I2C_FIFO_CONTROL_RX_TRIG(dma_burst);
} else {
chan = i2c_dev->tx_dma_chan;
reg_offset = tegra_i2c_reg_addr(i2c_dev, I2C_TX_FIFO);
slv_config.dst_addr = i2c_dev->base_phys + reg_offset;
slv_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
slv_config.dst_maxburst = dma_burst;
if (i2c_dev->hw->has_mst_fifo)
val = I2C_MST_FIFO_CONTROL_TX_TRIG(dma_burst);
else
val = I2C_FIFO_CONTROL_TX_TRIG(dma_burst);
}
slv_config.device_fc = true;
ret = dmaengine_slave_config(chan, &slv_config);
if (ret < 0) {
dev_err(i2c_dev->dev, "DMA slave config failed: %d\n",
ret);
dev_err(i2c_dev->dev, "falling back to PIO\n");
tegra_i2c_release_dma(i2c_dev);
i2c_dev->is_curr_dma_xfer = false;
} else {
goto out;
}
}
if (i2c_dev->hw->has_mst_fifo)
val = I2C_MST_FIFO_CONTROL_TX_TRIG(8) |
I2C_MST_FIFO_CONTROL_RX_TRIG(1);
else
val = I2C_FIFO_CONTROL_TX_TRIG(8) |
I2C_FIFO_CONTROL_RX_TRIG(1);
out:
i2c_writel(i2c_dev, val, reg);
}
static int tegra_i2c_issue_bus_clear(struct i2c_adapter *adap)
{
struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
int err;
unsigned long time_left;
u32 reg;
reinit_completion(&i2c_dev->msg_complete);
reg = (I2C_BC_SCLK_THRESHOLD << I2C_BC_SCLK_THRESHOLD_SHIFT) |
I2C_BC_STOP_COND | I2C_BC_TERMINATE;
i2c_writel(i2c_dev, reg, I2C_BUS_CLEAR_CNFG);
if (i2c_dev->hw->has_config_load_reg) {
err = tegra_i2c_wait_for_config_load(i2c_dev);
if (err)
return err;
}
reg |= I2C_BC_ENABLE;
i2c_writel(i2c_dev, reg, I2C_BUS_CLEAR_CNFG);
tegra_i2c_unmask_irq(i2c_dev, I2C_INT_BUS_CLR_DONE);
time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
msecs_to_jiffies(50));
if (time_left == 0) {
dev_err(i2c_dev->dev, "timed out for bus clear\n");
return -ETIMEDOUT;
}
reg = i2c_readl(i2c_dev, I2C_BUS_CLEAR_STATUS);
if (!(reg & I2C_BC_STATUS)) {
dev_err(i2c_dev->dev,
"un-recovered arbitration lost\n");
return -EIO;
}
return -EAGAIN;
}
static int tegra_i2c_xfer_msg(struct tegra_i2c_dev *i2c_dev,
struct i2c_msg *msg,
enum msg_end_type end_state)
{
u32 packet_header;
u32 int_mask;
unsigned long time_left;
unsigned long flags;
size_t xfer_size;
u32 *buffer = NULL;
int err = 0;
bool dma;
u16 xfer_time = 100;
tegra_i2c_flush_fifos(i2c_dev);
i2c_dev->msg_buf = msg->buf;
i2c_dev->msg_buf_remaining = msg->len;
i2c_dev->msg_err = I2C_ERR_NONE;
i2c_dev->msg_read = (msg->flags & I2C_M_RD);
reinit_completion(&i2c_dev->msg_complete);
if (i2c_dev->msg_read)
xfer_size = msg->len;
else
xfer_size = msg->len + I2C_PACKET_HEADER_SIZE;
xfer_size = ALIGN(xfer_size, BYTES_PER_FIFO_WORD);
i2c_dev->is_curr_dma_xfer = (xfer_size > I2C_PIO_MODE_MAX_LEN) &&
i2c_dev->dma_buf;
tegra_i2c_config_fifo_trig(i2c_dev, xfer_size);
dma = i2c_dev->is_curr_dma_xfer;
/*
* Transfer time in mSec = Total bits / transfer rate
* Total bits = 9 bits per byte (including ACK bit) + Start & stop bits
*/
xfer_time += DIV_ROUND_CLOSEST(((xfer_size * 9) + 2) * MSEC_PER_SEC,
i2c_dev->bus_clk_rate);
spin_lock_irqsave(&i2c_dev->xfer_lock, flags);
int_mask = I2C_INT_NO_ACK | I2C_INT_ARBITRATION_LOST;
tegra_i2c_unmask_irq(i2c_dev, int_mask);
if (dma) {
if (i2c_dev->msg_read) {
dma_sync_single_for_device(i2c_dev->dev,
i2c_dev->dma_phys,
xfer_size,
DMA_FROM_DEVICE);
err = tegra_i2c_dma_submit(i2c_dev, xfer_size);
if (err < 0) {
dev_err(i2c_dev->dev,
"starting RX DMA failed, err %d\n",
err);
goto unlock;
}
} else {
dma_sync_single_for_cpu(i2c_dev->dev,
i2c_dev->dma_phys,
xfer_size,
DMA_TO_DEVICE);
buffer = i2c_dev->dma_buf;
}
}
packet_header = (0 << PACKET_HEADER0_HEADER_SIZE_SHIFT) |
PACKET_HEADER0_PROTOCOL_I2C |
(i2c_dev->cont_id << PACKET_HEADER0_CONT_ID_SHIFT) |
(1 << PACKET_HEADER0_PACKET_ID_SHIFT);
if (dma && !i2c_dev->msg_read)
*buffer++ = packet_header;
else
i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);
packet_header = msg->len - 1;
if (dma && !i2c_dev->msg_read)
*buffer++ = packet_header;
else
i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);
packet_header = I2C_HEADER_IE_ENABLE;
if (end_state == MSG_END_CONTINUE)
packet_header |= I2C_HEADER_CONTINUE_XFER;
else if (end_state == MSG_END_REPEAT_START)
packet_header |= I2C_HEADER_REPEAT_START;
if (msg->flags & I2C_M_TEN) {
packet_header |= msg->addr;
packet_header |= I2C_HEADER_10BIT_ADDR;
} else {
packet_header |= msg->addr << I2C_HEADER_SLAVE_ADDR_SHIFT;
}
if (msg->flags & I2C_M_IGNORE_NAK)
packet_header |= I2C_HEADER_CONT_ON_NAK;
if (msg->flags & I2C_M_RD)
packet_header |= I2C_HEADER_READ;
if (dma && !i2c_dev->msg_read)
*buffer++ = packet_header;
else
i2c_writel(i2c_dev, packet_header, I2C_TX_FIFO);
if (!i2c_dev->msg_read) {
if (dma) {
memcpy(buffer, msg->buf, msg->len);
dma_sync_single_for_device(i2c_dev->dev,
i2c_dev->dma_phys,
xfer_size,
DMA_TO_DEVICE);
err = tegra_i2c_dma_submit(i2c_dev, xfer_size);
if (err < 0) {
dev_err(i2c_dev->dev,
"starting TX DMA failed, err %d\n",
err);
goto unlock;
}
} else {
tegra_i2c_fill_tx_fifo(i2c_dev);
}
}
if (i2c_dev->hw->has_per_pkt_xfer_complete_irq)
int_mask |= I2C_INT_PACKET_XFER_COMPLETE;
if (!dma) {
if (msg->flags & I2C_M_RD)
int_mask |= I2C_INT_RX_FIFO_DATA_REQ;
else if (i2c_dev->msg_buf_remaining)
int_mask |= I2C_INT_TX_FIFO_DATA_REQ;
}
tegra_i2c_unmask_irq(i2c_dev, int_mask);
dev_dbg(i2c_dev->dev, "unmasked irq: %02x\n",
i2c_readl(i2c_dev, I2C_INT_MASK));
unlock:
spin_unlock_irqrestore(&i2c_dev->xfer_lock, flags);
if (dma) {
if (err)
return err;
time_left = wait_for_completion_timeout(&i2c_dev->dma_complete,
msecs_to_jiffies(xfer_time));
if (time_left == 0) {
dev_err(i2c_dev->dev, "DMA transfer timeout\n");
dmaengine_terminate_sync(i2c_dev->msg_read ?
i2c_dev->rx_dma_chan :
i2c_dev->tx_dma_chan);
tegra_i2c_init(i2c_dev, true);
return -ETIMEDOUT;
}
if (i2c_dev->msg_read && i2c_dev->msg_err == I2C_ERR_NONE) {
dma_sync_single_for_cpu(i2c_dev->dev,
i2c_dev->dma_phys,
xfer_size,
DMA_FROM_DEVICE);
memcpy(i2c_dev->msg_buf, i2c_dev->dma_buf,
msg->len);
}
if (i2c_dev->msg_err != I2C_ERR_NONE)
dmaengine_synchronize(i2c_dev->msg_read ?
i2c_dev->rx_dma_chan :
i2c_dev->tx_dma_chan);
}
time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
msecs_to_jiffies(xfer_time));
tegra_i2c_mask_irq(i2c_dev, int_mask);
if (time_left == 0) {
dev_err(i2c_dev->dev, "i2c transfer timed out\n");
tegra_i2c_init(i2c_dev, true);
return -ETIMEDOUT;
}
dev_dbg(i2c_dev->dev, "transfer complete: %lu %d %d\n",
time_left, completion_done(&i2c_dev->msg_complete),
i2c_dev->msg_err);
i2c_dev->is_curr_dma_xfer = false;
if (likely(i2c_dev->msg_err == I2C_ERR_NONE))
return 0;
tegra_i2c_init(i2c_dev, true);
/* start recovery upon arbitration loss in single master mode */
if (i2c_dev->msg_err == I2C_ERR_ARBITRATION_LOST) {
if (!i2c_dev->is_multimaster_mode)
return i2c_recover_bus(&i2c_dev->adapter);
return -EAGAIN;
}
if (i2c_dev->msg_err == I2C_ERR_NO_ACK) {
if (msg->flags & I2C_M_IGNORE_NAK)
return 0;
return -EREMOTEIO;
}
return -EIO;
}
static int tegra_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
int num)
{
struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
int i;
int ret;
ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0) {
dev_err(i2c_dev->dev, "runtime resume failed %d\n", ret);
return ret;
}
for (i = 0; i < num; i++) {
enum msg_end_type end_type = MSG_END_STOP;
if (i < (num - 1)) {
if (msgs[i + 1].flags & I2C_M_NOSTART)
end_type = MSG_END_CONTINUE;
else
end_type = MSG_END_REPEAT_START;
}
ret = tegra_i2c_xfer_msg(i2c_dev, &msgs[i], end_type);
if (ret)
break;
}
pm_runtime_put(i2c_dev->dev);
return ret ?: i;
}
static u32 tegra_i2c_func(struct i2c_adapter *adap)
{
struct tegra_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
u32 ret = I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
I2C_FUNC_10BIT_ADDR | I2C_FUNC_PROTOCOL_MANGLING;
if (i2c_dev->hw->has_continue_xfer_support)
ret |= I2C_FUNC_NOSTART;
return ret;
}
static void tegra_i2c_parse_dt(struct tegra_i2c_dev *i2c_dev)
{
struct device_node *np = i2c_dev->dev->of_node;
int ret;
bool multi_mode;
ret = of_property_read_u32(np, "clock-frequency",
&i2c_dev->bus_clk_rate);
if (ret)
i2c_dev->bus_clk_rate = 100000; /* default clock rate */
multi_mode = of_property_read_bool(np, "multi-master");
i2c_dev->is_multimaster_mode = multi_mode;
}
static const struct i2c_algorithm tegra_i2c_algo = {
.master_xfer = tegra_i2c_xfer,
.functionality = tegra_i2c_func,
};
/* payload size is only 12 bit */
static const struct i2c_adapter_quirks tegra_i2c_quirks = {
.flags = I2C_AQ_NO_ZERO_LEN,
.max_read_len = SZ_4K,
.max_write_len = SZ_4K - I2C_PACKET_HEADER_SIZE,
};
static const struct i2c_adapter_quirks tegra194_i2c_quirks = {
.flags = I2C_AQ_NO_ZERO_LEN,
.max_write_len = SZ_64K - I2C_PACKET_HEADER_SIZE,
};
static struct i2c_bus_recovery_info tegra_i2c_recovery_info = {
.recover_bus = tegra_i2c_issue_bus_clear,
};
static const struct tegra_i2c_hw_feature tegra20_i2c_hw = {
.has_continue_xfer_support = false,
.has_per_pkt_xfer_complete_irq = false,
.has_single_clk_source = false,
.clk_divisor_hs_mode = 3,
.clk_divisor_std_mode = 0,
.clk_divisor_fast_mode = 0,
.clk_divisor_fast_plus_mode = 0,
.has_config_load_reg = false,
.has_multi_master_mode = false,
.has_slcg_override_reg = false,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = false,
.has_apb_dma = true,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x2,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0x0,
.setup_hold_time_fast_fast_plus_mode = 0x0,
.setup_hold_time_hs_mode = 0x0,
.has_interface_timing_reg = false,
};
static const struct tegra_i2c_hw_feature tegra30_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = false,
.has_single_clk_source = false,
.clk_divisor_hs_mode = 3,
.clk_divisor_std_mode = 0,
.clk_divisor_fast_mode = 0,
.clk_divisor_fast_plus_mode = 0,
.has_config_load_reg = false,
.has_multi_master_mode = false,
.has_slcg_override_reg = false,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = false,
.has_apb_dma = true,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x2,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0x0,
.setup_hold_time_fast_fast_plus_mode = 0x0,
.setup_hold_time_hs_mode = 0x0,
.has_interface_timing_reg = false,
};
static const struct tegra_i2c_hw_feature tegra114_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = true,
.has_single_clk_source = true,
.clk_divisor_hs_mode = 1,
.clk_divisor_std_mode = 0x19,
.clk_divisor_fast_mode = 0x19,
.clk_divisor_fast_plus_mode = 0x10,
.has_config_load_reg = false,
.has_multi_master_mode = false,
.has_slcg_override_reg = false,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = true,
.has_apb_dma = true,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x2,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0x0,
.setup_hold_time_fast_fast_plus_mode = 0x0,
.setup_hold_time_hs_mode = 0x0,
.has_interface_timing_reg = false,
};
static const struct tegra_i2c_hw_feature tegra124_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = true,
.has_single_clk_source = true,
.clk_divisor_hs_mode = 1,
.clk_divisor_std_mode = 0x19,
.clk_divisor_fast_mode = 0x19,
.clk_divisor_fast_plus_mode = 0x10,
.has_config_load_reg = true,
.has_multi_master_mode = false,
.has_slcg_override_reg = true,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = true,
.has_apb_dma = true,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x2,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0x0,
.setup_hold_time_fast_fast_plus_mode = 0x0,
.setup_hold_time_hs_mode = 0x0,
.has_interface_timing_reg = true,
};
static const struct tegra_i2c_hw_feature tegra210_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = true,
.has_single_clk_source = true,
.clk_divisor_hs_mode = 1,
.clk_divisor_std_mode = 0x19,
.clk_divisor_fast_mode = 0x19,
.clk_divisor_fast_plus_mode = 0x10,
.has_config_load_reg = true,
.has_multi_master_mode = false,
.has_slcg_override_reg = true,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = true,
.has_apb_dma = true,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x2,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0,
.setup_hold_time_fast_fast_plus_mode = 0,
.setup_hold_time_hs_mode = 0,
.has_interface_timing_reg = true,
};
static const struct tegra_i2c_hw_feature tegra186_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = true,
.has_single_clk_source = true,
.clk_divisor_hs_mode = 1,
.clk_divisor_std_mode = 0x16,
.clk_divisor_fast_mode = 0x19,
.clk_divisor_fast_plus_mode = 0x10,
.has_config_load_reg = true,
.has_multi_master_mode = false,
.has_slcg_override_reg = true,
.has_mst_fifo = false,
.quirks = &tegra_i2c_quirks,
.supports_bus_clear = true,
.has_apb_dma = false,
.tlow_std_mode = 0x4,
.thigh_std_mode = 0x3,
.tlow_fast_fastplus_mode = 0x4,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0,
.setup_hold_time_fast_fast_plus_mode = 0,
.setup_hold_time_hs_mode = 0,
.has_interface_timing_reg = true,
};
static const struct tegra_i2c_hw_feature tegra194_i2c_hw = {
.has_continue_xfer_support = true,
.has_per_pkt_xfer_complete_irq = true,
.has_single_clk_source = true,
.clk_divisor_hs_mode = 1,
.clk_divisor_std_mode = 0x4f,
.clk_divisor_fast_mode = 0x3c,
.clk_divisor_fast_plus_mode = 0x16,
.has_config_load_reg = true,
.has_multi_master_mode = true,
.has_slcg_override_reg = true,
.has_mst_fifo = true,
.quirks = &tegra194_i2c_quirks,
.supports_bus_clear = true,
.has_apb_dma = false,
.tlow_std_mode = 0x8,
.thigh_std_mode = 0x7,
.tlow_fast_fastplus_mode = 0x2,
.thigh_fast_fastplus_mode = 0x2,
.setup_hold_time_std_mode = 0x08080808,
.setup_hold_time_fast_fast_plus_mode = 0x02020202,
.setup_hold_time_hs_mode = 0x090909,
.has_interface_timing_reg = true,
};
/* Match table for of_platform binding */
static const struct of_device_id tegra_i2c_of_match[] = {
{ .compatible = "nvidia,tegra194-i2c", .data = &tegra194_i2c_hw, },
{ .compatible = "nvidia,tegra186-i2c", .data = &tegra186_i2c_hw, },
{ .compatible = "nvidia,tegra210-i2c", .data = &tegra210_i2c_hw, },
{ .compatible = "nvidia,tegra124-i2c", .data = &tegra124_i2c_hw, },
{ .compatible = "nvidia,tegra114-i2c", .data = &tegra114_i2c_hw, },
{ .compatible = "nvidia,tegra30-i2c", .data = &tegra30_i2c_hw, },
{ .compatible = "nvidia,tegra20-i2c", .data = &tegra20_i2c_hw, },
{ .compatible = "nvidia,tegra20-i2c-dvc", .data = &tegra20_i2c_hw, },
{},
};
MODULE_DEVICE_TABLE(of, tegra_i2c_of_match);
static int tegra_i2c_probe(struct platform_device *pdev)
{
struct tegra_i2c_dev *i2c_dev;
struct resource *res;
struct clk *div_clk;
struct clk *fast_clk;
void __iomem *base;
phys_addr_t base_phys;
int irq;
int ret;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
base_phys = res->start;
base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(base))
return PTR_ERR(base);
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!res) {
dev_err(&pdev->dev, "no irq resource\n");
return -EINVAL;
}
irq = res->start;
div_clk = devm_clk_get(&pdev->dev, "div-clk");
if (IS_ERR(div_clk)) {
if (PTR_ERR(div_clk) != -EPROBE_DEFER)
dev_err(&pdev->dev, "missing controller clock\n");
return PTR_ERR(div_clk);
}
i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
if (!i2c_dev)
return -ENOMEM;
i2c_dev->base = base;
i2c_dev->base_phys = base_phys;
i2c_dev->div_clk = div_clk;
i2c_dev->adapter.algo = &tegra_i2c_algo;
i2c_dev->adapter.retries = 1;
i2c_dev->adapter.timeout = 6 * HZ;
i2c_dev->irq = irq;
i2c_dev->cont_id = pdev->id;
i2c_dev->dev = &pdev->dev;
i2c_dev->rst = devm_reset_control_get_exclusive(&pdev->dev, "i2c");
if (IS_ERR(i2c_dev->rst)) {
dev_err(&pdev->dev, "missing controller reset\n");
return PTR_ERR(i2c_dev->rst);
}
tegra_i2c_parse_dt(i2c_dev);
i2c_dev->hw = of_device_get_match_data(&pdev->dev);
i2c_dev->is_dvc = of_device_is_compatible(pdev->dev.of_node,
"nvidia,tegra20-i2c-dvc");
i2c_dev->adapter.quirks = i2c_dev->hw->quirks;
i2c_dev->dma_buf_size = i2c_dev->adapter.quirks->max_write_len +
I2C_PACKET_HEADER_SIZE;
init_completion(&i2c_dev->msg_complete);
init_completion(&i2c_dev->dma_complete);
spin_lock_init(&i2c_dev->xfer_lock);
if (!i2c_dev->hw->has_single_clk_source) {
fast_clk = devm_clk_get(&pdev->dev, "fast-clk");
if (IS_ERR(fast_clk)) {
dev_err(&pdev->dev, "missing fast clock\n");
return PTR_ERR(fast_clk);
}
i2c_dev->fast_clk = fast_clk;
}
platform_set_drvdata(pdev, i2c_dev);
if (!i2c_dev->hw->has_single_clk_source) {
ret = clk_prepare(i2c_dev->fast_clk);
if (ret < 0) {
dev_err(i2c_dev->dev, "Clock prepare failed %d\n", ret);
return ret;
}
}
if (i2c_dev->bus_clk_rate > I2C_FAST_MODE &&
i2c_dev->bus_clk_rate <= I2C_FAST_PLUS_MODE)
i2c_dev->clk_divisor_non_hs_mode =
i2c_dev->hw->clk_divisor_fast_plus_mode;
else if (i2c_dev->bus_clk_rate > I2C_STANDARD_MODE &&
i2c_dev->bus_clk_rate <= I2C_FAST_MODE)
i2c_dev->clk_divisor_non_hs_mode =
i2c_dev->hw->clk_divisor_fast_mode;
else
i2c_dev->clk_divisor_non_hs_mode =
i2c_dev->hw->clk_divisor_std_mode;
ret = clk_prepare(i2c_dev->div_clk);
if (ret < 0) {
dev_err(i2c_dev->dev, "Clock prepare failed %d\n", ret);
goto unprepare_fast_clk;
}
pm_runtime_enable(&pdev->dev);
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
if (!pm_runtime_enabled(&pdev->dev))
ret = tegra_i2c_runtime_resume(&pdev->dev);
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
else
ret = pm_runtime_get_sync(i2c_dev->dev);
if (ret < 0) {
dev_err(&pdev->dev, "runtime resume failed\n");
goto unprepare_div_clk;
}
if (i2c_dev->is_multimaster_mode) {
ret = clk_enable(i2c_dev->div_clk);
if (ret < 0) {
dev_err(i2c_dev->dev, "div_clk enable failed %d\n",
ret);
goto disable_rpm;
}
}
if (i2c_dev->hw->supports_bus_clear)
i2c_dev->adapter.bus_recovery_info = &tegra_i2c_recovery_info;
ret = tegra_i2c_init_dma(i2c_dev);
if (ret < 0)
goto disable_div_clk;
ret = tegra_i2c_init(i2c_dev, false);
if (ret) {
dev_err(&pdev->dev, "Failed to initialize i2c controller\n");
goto release_dma;
}
ret = devm_request_irq(&pdev->dev, i2c_dev->irq,
tegra_i2c_isr, 0, dev_name(&pdev->dev), i2c_dev);
if (ret) {
dev_err(&pdev->dev, "Failed to request irq %i\n", i2c_dev->irq);
goto release_dma;
}
i2c_set_adapdata(&i2c_dev->adapter, i2c_dev);
i2c_dev->adapter.owner = THIS_MODULE;
i2c_dev->adapter.class = I2C_CLASS_DEPRECATED;
strlcpy(i2c_dev->adapter.name, dev_name(&pdev->dev),
sizeof(i2c_dev->adapter.name));
i2c_dev->adapter.dev.parent = &pdev->dev;
i2c_dev->adapter.nr = pdev->id;
i2c_dev->adapter.dev.of_node = pdev->dev.of_node;
ret = i2c_add_numbered_adapter(&i2c_dev->adapter);
if (ret)
goto release_dma;
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
pm_runtime_put(&pdev->dev);
return 0;
release_dma:
tegra_i2c_release_dma(i2c_dev);
disable_div_clk:
if (i2c_dev->is_multimaster_mode)
clk_disable(i2c_dev->div_clk);
disable_rpm:
pm_runtime_disable(&pdev->dev);
if (!pm_runtime_status_suspended(&pdev->dev))
tegra_i2c_runtime_suspend(&pdev->dev);
unprepare_div_clk:
clk_unprepare(i2c_dev->div_clk);
unprepare_fast_clk:
if (!i2c_dev->hw->has_single_clk_source)
clk_unprepare(i2c_dev->fast_clk);
return ret;
}
static int tegra_i2c_remove(struct platform_device *pdev)
{
struct tegra_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
i2c_del_adapter(&i2c_dev->adapter);
if (i2c_dev->is_multimaster_mode)
clk_disable(i2c_dev->div_clk);
pm_runtime_disable(&pdev->dev);
if (!pm_runtime_status_suspended(&pdev->dev))
tegra_i2c_runtime_suspend(&pdev->dev);
clk_unprepare(i2c_dev->div_clk);
if (!i2c_dev->hw->has_single_clk_source)
clk_unprepare(i2c_dev->fast_clk);
tegra_i2c_release_dma(i2c_dev);
return 0;
}
static int __maybe_unused tegra_i2c_suspend(struct device *dev)
{
struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
i2c_mark_adapter_suspended(&i2c_dev->adapter);
return 0;
}
static int __maybe_unused tegra_i2c_resume(struct device *dev)
{
struct tegra_i2c_dev *i2c_dev = dev_get_drvdata(dev);
int err;
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
err = tegra_i2c_runtime_resume(dev);
if (err)
return err;
err = tegra_i2c_init(i2c_dev, false);
if (err)
return err;
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
err = tegra_i2c_runtime_suspend(dev);
if (err)
return err;
i2c_mark_adapter_resumed(&i2c_dev->adapter);
return 0;
}
static const struct dev_pm_ops tegra_i2c_pm = {
i2c: tegra: Move suspend handling to NOIRQ phase Commit acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") added suspend support for the Tegra I2C driver and following this change on Tegra30 the following WARNING is seen on entering suspend ... WARNING: CPU: 2 PID: 689 at /dvs/git/dirty/git-master_l4t-upstream/kernel/drivers/i2c/i2c-core.h:54 __i2c_transfer+0x35c/0x70c i2c i2c-4: Transfer while suspended Modules linked in: brcmfmac brcmutil CPU: 2 PID: 689 Comm: rtcwake Not tainted 5.3.0-rc7-g089cf7f6ecb2 #1 Hardware name: NVIDIA Tegra SoC (Flattened Device Tree) [<c0112264>] (unwind_backtrace) from [<c010ca94>] (show_stack+0x10/0x14) [<c010ca94>] (show_stack) from [<c0a77024>] (dump_stack+0xb4/0xc8) [<c0a77024>] (dump_stack) from [<c0124198>] (__warn+0xe0/0xf8) [<c0124198>] (__warn) from [<c01241f8>] (warn_slowpath_fmt+0x48/0x6c) [<c01241f8>] (warn_slowpath_fmt) from [<c06f6c40>] (__i2c_transfer+0x35c/0x70c) [<c06f6c40>] (__i2c_transfer) from [<c06f7048>] (i2c_transfer+0x58/0xf4) [<c06f7048>] (i2c_transfer) from [<c06f7130>] (i2c_transfer_buffer_flags+0x4c/0x70) [<c06f7130>] (i2c_transfer_buffer_flags) from [<c05bee78>] (regmap_i2c_write+0x14/0x30) [<c05bee78>] (regmap_i2c_write) from [<c05b9cac>] (_regmap_raw_write_impl+0x35c/0x868) [<c05b9cac>] (_regmap_raw_write_impl) from [<c05b984c>] (_regmap_update_bits+0xe4/0xec) [<c05b984c>] (_regmap_update_bits) from [<c05bad04>] (regmap_update_bits_base+0x50/0x74) [<c05bad04>] (regmap_update_bits_base) from [<c04d453c>] (regulator_disable_regmap+0x44/0x54) [<c04d453c>] (regulator_disable_regmap) from [<c04cf9d4>] (_regulator_do_disable+0xf8/0x268) [<c04cf9d4>] (_regulator_do_disable) from [<c04d1694>] (_regulator_disable+0xf4/0x19c) [<c04d1694>] (_regulator_disable) from [<c04d1770>] (regulator_disable+0x34/0x64) [<c04d1770>] (regulator_disable) from [<c04d2310>] (regulator_bulk_disable+0x28/0xb4) [<c04d2310>] (regulator_bulk_disable) from [<c0495cd4>] (tegra_pcie_power_off+0x64/0xa8) [<c0495cd4>] (tegra_pcie_power_off) from [<c0495f74>] (tegra_pcie_pm_suspend+0x25c/0x3f4) [<c0495f74>] (tegra_pcie_pm_suspend) from [<c05af48c>] (dpm_run_callback+0x38/0x1d4) [<c05af48c>] (dpm_run_callback) from [<c05afe30>] (__device_suspend_noirq+0xc0/0x2b8) [<c05afe30>] (__device_suspend_noirq) from [<c05b1c24>] (dpm_noirq_suspend_devices+0x100/0x37c) [<c05b1c24>] (dpm_noirq_suspend_devices) from [<c05b1ebc>] (dpm_suspend_noirq+0x1c/0x48) [<c05b1ebc>] (dpm_suspend_noirq) from [<c017d2c0>] (suspend_devices_and_enter+0x1d0/0xa00) [<c017d2c0>] (suspend_devices_and_enter) from [<c017dd10>] (pm_suspend+0x220/0x74c) [<c017dd10>] (pm_suspend) from [<c017c2c8>] (state_store+0x6c/0xc8) [<c017c2c8>] (state_store) from [<c02ef398>] (kernfs_fop_write+0xe8/0x1c4) [<c02ef398>] (kernfs_fop_write) from [<c0271e38>] (__vfs_write+0x2c/0x1c4) [<c0271e38>] (__vfs_write) from [<c02748dc>] (vfs_write+0xa4/0x184) [<c02748dc>] (vfs_write) from [<c0274b7c>] (ksys_write+0x9c/0xdc) [<c0274b7c>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x54) Exception stack(0xe9f21fa8 to 0xe9f21ff0) 1fa0: 0000006c 004b2438 00000004 004b2438 00000004 00000000 1fc0: 0000006c 004b2438 004b1228 00000004 00000004 00000004 0049e78c 004b1228 1fe0: 00000004 be9809b8 b6f0bc0b b6e96206 The problem is that the Tegra PCIe driver indirectly uses I2C for controlling some regulators and the I2C driver is now being suspended before the PCIe driver causing the PCIe suspend to fail. The Tegra PCIe driver is suspended during the NOIRQ phase and this cannot be changed due to other dependencies. Therefore, we also need to move the suspend handling for the Tegra I2C driver to the NOIRQ phase as well. In order to move the I2C suspend handling to the NOIRQ phase we also need to avoid calling pm_runtime_get/put() because per commit 1e2ef05bb8cf ("PM: Limit race conditions between runtime PM and system sleep (v2)") these cannot be called early in resume. The function tegra_i2c_init(), called during resume, calls pm_runtime_get/put() and so move these calls outside of tegra_i2c_init(), so this function can be used during the NOIRQ resume phase. Fixes: acc8abcb2a9c ("i2c: tegra: Add suspend-resume support") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-09-10 09:29:17 +00:00
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(tegra_i2c_suspend, tegra_i2c_resume)
SET_RUNTIME_PM_OPS(tegra_i2c_runtime_suspend, tegra_i2c_runtime_resume,
NULL)
};
static struct platform_driver tegra_i2c_driver = {
.probe = tegra_i2c_probe,
.remove = tegra_i2c_remove,
.driver = {
.name = "tegra-i2c",
.of_match_table = tegra_i2c_of_match,
.pm = &tegra_i2c_pm,
},
};
module_platform_driver(tegra_i2c_driver);
MODULE_DESCRIPTION("nVidia Tegra2 I2C Bus Controller driver");
MODULE_AUTHOR("Colin Cross");
MODULE_LICENSE("GPL v2");