mirror of
https://github.com/torvalds/linux.git
synced 2024-12-24 11:51:27 +00:00
70 lines
2.5 KiB
Plaintext
70 lines
2.5 KiB
Plaintext
|
Socionext UniPhier USB3 High-Speed (HS) PHY
|
||
|
|
||
|
This describes the devicetree bindings for PHY interfaces built into
|
||
|
USB3 controller implemented on Socionext UniPhier SoCs.
|
||
|
Although the controller includes High-Speed PHY and Super-Speed PHY,
|
||
|
this describes about High-Speed PHY.
|
||
|
|
||
|
Required properties:
|
||
|
- compatible: Should contain one of the following:
|
||
|
"socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
|
||
|
"socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
|
||
|
"socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
|
||
|
"socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
|
||
|
- reg: Specifies offset and length of the register set for the device.
|
||
|
- #phy-cells: Should be 0.
|
||
|
- clocks: A list of phandles to the clock gate for USB3 glue layer.
|
||
|
According to the clock-names, appropriate clocks are required.
|
||
|
- clock-names: Should contain the following:
|
||
|
"gio", "link" - for Pro4 SoC
|
||
|
"phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
|
||
|
"phy", "link" - for others
|
||
|
- resets: A list of phandles to the reset control for USB3 glue layer.
|
||
|
According to the reset-names, appropriate resets are required.
|
||
|
- reset-names: Should contain the following:
|
||
|
"gio", "link" - for Pro4 SoC
|
||
|
"phy", "link" - for others
|
||
|
|
||
|
Optional properties:
|
||
|
- vbus-supply: A phandle to the regulator for USB VBUS.
|
||
|
- nvmem-cells: Phandles to nvmem cell that contains the trimming data.
|
||
|
Available only for HS-PHY implemented on LD20 and PXs3, and
|
||
|
if unspecified, default value is used.
|
||
|
- nvmem-cell-names: Should be the following names, which correspond to
|
||
|
each nvmem-cells.
|
||
|
All of the 3 parameters associated with the following names are
|
||
|
required for each port, if any one is omitted, the trimming data
|
||
|
of the port will not be set at all.
|
||
|
"rterm", "sel_t", "hs_i" - Each cell name for phy parameters
|
||
|
|
||
|
Refer to phy/phy-bindings.txt for the generic PHY binding properties.
|
||
|
|
||
|
Example:
|
||
|
|
||
|
usb-glue@65b00000 {
|
||
|
compatible = "socionext,uniphier-ld20-dwc3-glue",
|
||
|
"simple-mfd";
|
||
|
#address-cells = <1>;
|
||
|
#size-cells = <1>;
|
||
|
ranges = <0 0x65b00000 0x400>;
|
||
|
|
||
|
usb_vbus0: regulator {
|
||
|
...
|
||
|
};
|
||
|
|
||
|
usb_hsphy0: hs-phy@200 {
|
||
|
compatible = "socionext,uniphier-ld20-usb3-hsphy";
|
||
|
reg = <0x200 0x10>;
|
||
|
#phy-cells = <0>;
|
||
|
clock-names = "link", "phy";
|
||
|
clocks = <&sys_clk 14>, <&sys_clk 16>;
|
||
|
reset-names = "link", "phy";
|
||
|
resets = <&sys_rst 14>, <&sys_rst 16>;
|
||
|
vbus-supply = <&usb_vbus0>;
|
||
|
nvmem-cell-names = "rterm", "sel_t", "hs_i";
|
||
|
nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>,
|
||
|
<&usb_hs_i0>;
|
||
|
};
|
||
|
...
|
||
|
};
|