2019-06-04 08:11:32 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-only
|
2015-09-04 22:47:04 +00:00
|
|
|
/*
|
|
|
|
|
* mm/userfaultfd.c
|
|
|
|
|
*
|
|
|
|
|
* Copyright (C) 2015 Red Hat, Inc.
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include <linux/mm.h>
|
2017-02-02 18:15:33 +00:00
|
|
|
#include <linux/sched/signal.h>
|
2015-09-04 22:47:04 +00:00
|
|
|
#include <linux/pagemap.h>
|
|
|
|
|
#include <linux/rmap.h>
|
|
|
|
|
#include <linux/swap.h>
|
|
|
|
|
#include <linux/swapops.h>
|
|
|
|
|
#include <linux/userfaultfd_k.h>
|
|
|
|
|
#include <linux/mmu_notifier.h>
|
2017-02-22 23:42:55 +00:00
|
|
|
#include <linux/hugetlb.h>
|
2017-02-22 23:43:34 +00:00
|
|
|
#include <linux/shmem_fs.h>
|
2015-09-04 22:47:04 +00:00
|
|
|
#include <asm/tlbflush.h>
|
mm/mprotect: use mmu_gather
Patch series "mm/mprotect: avoid unnecessary TLB flushes", v6.
This patchset is intended to remove unnecessary TLB flushes during
mprotect() syscalls. Once this patch-set make it through, similar and
further optimizations for MADV_COLD and userfaultfd would be possible.
Basically, there are 3 optimizations in this patch-set:
1. Use TLB batching infrastructure to batch flushes across VMAs and do
better/fewer flushes. This would also be handy for later userfaultfd
enhancements.
2. Avoid unnecessary TLB flushes. This optimization is the one that
provides most of the performance benefits. Unlike previous versions,
we now only avoid flushes that would not result in spurious
page-faults.
3. Avoiding TLB flushes on change_huge_pmd() that are only needed to
prevent the A/D bits from changing.
Andrew asked for some benchmark numbers. I do not have an easy
determinate macrobenchmark in which it is easy to show benefit. I
therefore ran a microbenchmark: a loop that does the following on
anonymous memory, just as a sanity check to see that time is saved by
avoiding TLB flushes. The loop goes:
mprotect(p, PAGE_SIZE, PROT_READ)
mprotect(p, PAGE_SIZE, PROT_READ|PROT_WRITE)
*p = 0; // make the page writable
The test was run in KVM guest with 1 or 2 threads (the second thread was
busy-looping). I measured the time (cycles) of each operation:
1 thread 2 threads
mmots +patch mmots +patch
PROT_READ 3494 2725 (-22%) 8630 7788 (-10%)
PROT_READ|WRITE 3952 2724 (-31%) 9075 2865 (-68%)
[ mmots = v5.17-rc6-mmots-2022-03-06-20-38 ]
The exact numbers are really meaningless, but the benefit is clear. There
are 2 interesting results though.
(1) PROT_READ is cheaper, while one can expect it not to be affected.
This is presumably due to TLB miss that is saved
(2) Without memory access (*p = 0), the speedup of the patch is even
greater. In that scenario mprotect(PROT_READ) also avoids the TLB flush.
As a result both operations on the patched kernel take roughly ~1500
cycles (with either 1 or 2 threads), whereas on mmotm their cost is as
high as presented in the table.
This patch (of 3):
change_pXX_range() currently does not use mmu_gather, but instead
implements its own deferred TLB flushes scheme. This both complicates the
code, as developers need to be aware of different invalidation schemes,
and prevents opportunities to avoid TLB flushes or perform them in finer
granularity.
The use of mmu_gather for modified PTEs has benefits in various scenarios
even if pages are not released. For instance, if only a single page needs
to be flushed out of a range of many pages, only that page would be
flushed. If a THP page is flushed, on x86 a single TLB invlpg instruction
can be used instead of 512 instructions (or a full TLB flush, which would
Linux would actually use by default). mprotect() over multiple VMAs
requires a single flush.
Use mmu_gather in change_pXX_range(). As the pages are not released, only
record the flushed range using tlb_flush_pXX_range().
Handle THP similarly and get rid of flush_cache_range() which becomes
redundant since tlb_start_vma() calls it when needed.
Link: https://lkml.kernel.org/r/20220401180821.1986781-1-namit@vmware.com
Link: https://lkml.kernel.org/r/20220401180821.1986781-2-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:50 +00:00
|
|
|
#include <asm/tlb.h>
|
2015-09-04 22:47:04 +00:00
|
|
|
#include "internal.h"
|
|
|
|
|
|
2019-12-01 01:57:55 +00:00
|
|
|
static __always_inline
|
|
|
|
|
struct vm_area_struct *find_dst_vma(struct mm_struct *dst_mm,
|
|
|
|
|
unsigned long dst_start,
|
|
|
|
|
unsigned long len)
|
|
|
|
|
{
|
|
|
|
|
/*
|
|
|
|
|
* Make sure that the dst range is both valid and fully within a
|
|
|
|
|
* single existing vma.
|
|
|
|
|
*/
|
|
|
|
|
struct vm_area_struct *dst_vma;
|
|
|
|
|
|
|
|
|
|
dst_vma = find_vma(dst_mm, dst_start);
|
|
|
|
|
if (!dst_vma)
|
|
|
|
|
return NULL;
|
|
|
|
|
|
|
|
|
|
if (dst_start < dst_vma->vm_start ||
|
|
|
|
|
dst_start + len > dst_vma->vm_end)
|
|
|
|
|
return NULL;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Check the vma is registered in uffd, this is required to
|
|
|
|
|
* enforce the VM_MAYWRITE check done at uffd registration
|
|
|
|
|
* time.
|
|
|
|
|
*/
|
|
|
|
|
if (!dst_vma->vm_userfaultfd_ctx.ctx)
|
|
|
|
|
return NULL;
|
|
|
|
|
|
|
|
|
|
return dst_vma;
|
|
|
|
|
}
|
|
|
|
|
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
/*
|
|
|
|
|
* Install PTEs, to map dst_addr (within dst_vma) to page.
|
|
|
|
|
*
|
userfaultfd/shmem: modify shmem_mfill_atomic_pte to use install_pte()
In a previous commit, we added the mfill_atomic_install_pte() helper.
This helper does the job of setting up PTEs for an existing page, to map
it into a given VMA. It deals with both the anon and shmem cases, as well
as the shared and private cases.
In other words, shmem_mfill_atomic_pte() duplicates a case it already
handles. So, expose it, and let shmem_mfill_atomic_pte() use it directly,
to reduce code duplication.
This requires that we refactor shmem_mfill_atomic_pte() a bit:
Instead of doing accounting (shmem_recalc_inode() et al) part-way through
the PTE setup, do it afterward. This frees up mfill_atomic_install_pte()
from having to care about this accounting, and means we don't need to e.g.
shmem_uncharge() in the error path.
A side effect is this switches shmem_mfill_atomic_pte() to use
lru_cache_add_inactive_or_unevictable() instead of just lru_cache_add().
This wrapper does some extra accounting in an exceptional case, if
appropriate, so it's actually the more correct thing to use.
Link: https://lkml.kernel.org/r/20210503180737.2487560-7-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:31 +00:00
|
|
|
* This function handles both MCOPY_ATOMIC_NORMAL and _CONTINUE for both shmem
|
|
|
|
|
* and anon, and for both shared and private VMAs.
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
*/
|
userfaultfd/shmem: modify shmem_mfill_atomic_pte to use install_pte()
In a previous commit, we added the mfill_atomic_install_pte() helper.
This helper does the job of setting up PTEs for an existing page, to map
it into a given VMA. It deals with both the anon and shmem cases, as well
as the shared and private cases.
In other words, shmem_mfill_atomic_pte() duplicates a case it already
handles. So, expose it, and let shmem_mfill_atomic_pte() use it directly,
to reduce code duplication.
This requires that we refactor shmem_mfill_atomic_pte() a bit:
Instead of doing accounting (shmem_recalc_inode() et al) part-way through
the PTE setup, do it afterward. This frees up mfill_atomic_install_pte()
from having to care about this accounting, and means we don't need to e.g.
shmem_uncharge() in the error path.
A side effect is this switches shmem_mfill_atomic_pte() to use
lru_cache_add_inactive_or_unevictable() instead of just lru_cache_add().
This wrapper does some extra accounting in an exceptional case, if
appropriate, so it's actually the more correct thing to use.
Link: https://lkml.kernel.org/r/20210503180737.2487560-7-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:31 +00:00
|
|
|
int mfill_atomic_install_pte(struct mm_struct *dst_mm, pmd_t *dst_pmd,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_addr, struct page *page,
|
|
|
|
|
bool newly_allocated, bool wp_copy)
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
{
|
|
|
|
|
int ret;
|
|
|
|
|
pte_t _dst_pte, *dst_pte;
|
|
|
|
|
bool writable = dst_vma->vm_flags & VM_WRITE;
|
|
|
|
|
bool vm_shared = dst_vma->vm_flags & VM_SHARED;
|
|
|
|
|
bool page_in_cache = page->mapping;
|
|
|
|
|
spinlock_t *ptl;
|
|
|
|
|
struct inode *inode;
|
|
|
|
|
pgoff_t offset, max_off;
|
|
|
|
|
|
|
|
|
|
_dst_pte = mk_pte(page, dst_vma->vm_page_prot);
|
mm/shmem: unconditionally set pte dirty in mfill_atomic_install_pte
Patch series "mm: A few cleanup patches around zap, shmem and uffd", v4.
IMHO all of them are very nice cleanups to existing code already,
they're all small and self-contained. They'll be needed by uffd-wp
coming series.
This patch (of 4):
It was conditionally done previously, as there's one shmem special case
that we use SetPageDirty() instead. However that's not necessary and it
should be easier and cleaner to do it unconditionally in
mfill_atomic_install_pte().
The most recent discussion about this is here, where Hugh explained the
history of SetPageDirty() and why it's possible that it's not required
at all:
https://lore.kernel.org/lkml/alpine.LSU.2.11.2104121657050.1097@eggly.anvils/
Currently mfill_atomic_install_pte() has three callers:
1. shmem_mfill_atomic_pte
2. mcopy_atomic_pte
3. mcontinue_atomic_pte
After the change: case (1) should have its SetPageDirty replaced by the
dirty bit on pte (so we unify them together, finally), case (2) should
have no functional change at all as it has page_in_cache==false, case
(3) may add a dirty bit to the pte. However since case (3) is
UFFDIO_CONTINUE for shmem, it's merely 100% sure the page is dirty after
all because UFFDIO_CONTINUE normally requires another process to modify
the page cache and kick the faulted thread, so should not make a real
difference either.
This should make it much easier to follow on which case will set dirty
for uffd, as we'll simply set it all now for all uffd related ioctls.
Meanwhile, no special handling of SetPageDirty() if there's no need.
Link: https://lkml.kernel.org/r/20210915181456.10739-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20210915181456.10739-2-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Axel Rasmussen <axelrasmussen@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Liam Howlett <liam.howlett@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-11-05 20:38:24 +00:00
|
|
|
_dst_pte = pte_mkdirty(_dst_pte);
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
if (page_in_cache && !vm_shared)
|
|
|
|
|
writable = false;
|
2022-04-21 23:35:43 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Always mark a PTE as write-protected when needed, regardless of
|
|
|
|
|
* VM_WRITE, which the user might change.
|
|
|
|
|
*/
|
|
|
|
|
if (wp_copy)
|
|
|
|
|
_dst_pte = pte_mkuffd_wp(_dst_pte);
|
|
|
|
|
else if (writable)
|
|
|
|
|
_dst_pte = pte_mkwrite(_dst_pte);
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
|
|
|
|
|
dst_pte = pte_offset_map_lock(dst_mm, dst_pmd, dst_addr, &ptl);
|
|
|
|
|
|
|
|
|
|
if (vma_is_shmem(dst_vma)) {
|
|
|
|
|
/* serialize against truncate with the page table lock */
|
|
|
|
|
inode = dst_vma->vm_file->f_inode;
|
|
|
|
|
offset = linear_page_index(dst_vma, dst_addr);
|
|
|
|
|
max_off = DIV_ROUND_UP(i_size_read(inode), PAGE_SIZE);
|
|
|
|
|
ret = -EFAULT;
|
|
|
|
|
if (unlikely(offset >= max_off))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
ret = -EEXIST;
|
|
|
|
|
if (!pte_none(*dst_pte))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
mm/munlock: rmap call mlock_vma_page() munlock_vma_page()
Add vma argument to mlock_vma_page() and munlock_vma_page(), make them
inline functions which check (vma->vm_flags & VM_LOCKED) before calling
mlock_page() and munlock_page() in mm/mlock.c.
Add bool compound to mlock_vma_page() and munlock_vma_page(): this is
because we have understandable difficulty in accounting pte maps of THPs,
and if passed a PageHead page, mlock_page() and munlock_page() cannot
tell whether it's a pmd map to be counted or a pte map to be ignored.
Add vma arg to page_add_file_rmap() and page_remove_rmap(), like the
others, and use that to call mlock_vma_page() at the end of the page
adds, and munlock_vma_page() at the end of page_remove_rmap() (end or
beginning? unimportant, but end was easier for assertions in testing).
No page lock is required (although almost all adds happen to hold it):
delete the "Serialize with page migration" BUG_ON(!PageLocked(page))s.
Certainly page lock did serialize with page migration, but I'm having
difficulty explaining why that was ever important.
Mlock accounting on THPs has been hard to define, differed between anon
and file, involved PageDoubleMap in some places and not others, required
clear_page_mlock() at some points. Keep it simple now: just count the
pmds and ignore the ptes, there is no reason for ptes to undo pmd mlocks.
page_add_new_anon_rmap() callers unchanged: they have long been calling
lru_cache_add_inactive_or_unevictable(), which does its own VM_LOCKED
handling (it also checks for not VM_SPECIAL: I think that's overcautious,
and inconsistent with other checks, that mmap_region() already prevents
VM_LOCKED on VM_SPECIAL; but haven't quite convinced myself to change it).
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
2022-02-15 02:26:39 +00:00
|
|
|
if (page_in_cache) {
|
|
|
|
|
/* Usually, cache pages are already added to LRU */
|
|
|
|
|
if (newly_allocated)
|
|
|
|
|
lru_cache_add(page);
|
|
|
|
|
page_add_file_rmap(page, dst_vma, false);
|
|
|
|
|
} else {
|
2022-05-10 01:20:43 +00:00
|
|
|
page_add_new_anon_rmap(page, dst_vma, dst_addr);
|
mm/munlock: rmap call mlock_vma_page() munlock_vma_page()
Add vma argument to mlock_vma_page() and munlock_vma_page(), make them
inline functions which check (vma->vm_flags & VM_LOCKED) before calling
mlock_page() and munlock_page() in mm/mlock.c.
Add bool compound to mlock_vma_page() and munlock_vma_page(): this is
because we have understandable difficulty in accounting pte maps of THPs,
and if passed a PageHead page, mlock_page() and munlock_page() cannot
tell whether it's a pmd map to be counted or a pte map to be ignored.
Add vma arg to page_add_file_rmap() and page_remove_rmap(), like the
others, and use that to call mlock_vma_page() at the end of the page
adds, and munlock_vma_page() at the end of page_remove_rmap() (end or
beginning? unimportant, but end was easier for assertions in testing).
No page lock is required (although almost all adds happen to hold it):
delete the "Serialize with page migration" BUG_ON(!PageLocked(page))s.
Certainly page lock did serialize with page migration, but I'm having
difficulty explaining why that was ever important.
Mlock accounting on THPs has been hard to define, differed between anon
and file, involved PageDoubleMap in some places and not others, required
clear_page_mlock() at some points. Keep it simple now: just count the
pmds and ignore the ptes, there is no reason for ptes to undo pmd mlocks.
page_add_new_anon_rmap() callers unchanged: they have long been calling
lru_cache_add_inactive_or_unevictable(), which does its own VM_LOCKED
handling (it also checks for not VM_SPECIAL: I think that's overcautious,
and inconsistent with other checks, that mmap_region() already prevents
VM_LOCKED on VM_SPECIAL; but haven't quite convinced myself to change it).
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
2022-02-15 02:26:39 +00:00
|
|
|
lru_cache_add_inactive_or_unevictable(page, dst_vma);
|
|
|
|
|
}
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Must happen after rmap, as mm_counter() checks mapping (via
|
|
|
|
|
* PageAnon()), which is set by __page_set_anon_rmap().
|
|
|
|
|
*/
|
|
|
|
|
inc_mm_counter(dst_mm, mm_counter(page));
|
|
|
|
|
|
|
|
|
|
set_pte_at(dst_mm, dst_addr, dst_pte, _dst_pte);
|
|
|
|
|
|
|
|
|
|
/* No need to invalidate - it was non-present before */
|
|
|
|
|
update_mmu_cache(dst_vma, dst_addr, dst_pte);
|
|
|
|
|
ret = 0;
|
|
|
|
|
out_unlock:
|
|
|
|
|
pte_unmap_unlock(dst_pte, ptl);
|
|
|
|
|
return ret;
|
|
|
|
|
}
|
|
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
static int mcopy_atomic_pte(struct mm_struct *dst_mm,
|
|
|
|
|
pmd_t *dst_pmd,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_addr,
|
2015-09-04 22:47:08 +00:00
|
|
|
unsigned long src_addr,
|
2020-04-07 03:05:41 +00:00
|
|
|
struct page **pagep,
|
|
|
|
|
bool wp_copy)
|
2015-09-04 22:47:04 +00:00
|
|
|
{
|
|
|
|
|
void *page_kaddr;
|
|
|
|
|
int ret;
|
2015-09-04 22:47:08 +00:00
|
|
|
struct page *page;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
2015-09-04 22:47:08 +00:00
|
|
|
if (!*pagep) {
|
|
|
|
|
ret = -ENOMEM;
|
|
|
|
|
page = alloc_page_vma(GFP_HIGHUSER_MOVABLE, dst_vma, dst_addr);
|
|
|
|
|
if (!page)
|
|
|
|
|
goto out;
|
|
|
|
|
|
|
|
|
|
page_kaddr = kmap_atomic(page);
|
|
|
|
|
ret = copy_from_user(page_kaddr,
|
|
|
|
|
(const void __user *) src_addr,
|
|
|
|
|
PAGE_SIZE);
|
|
|
|
|
kunmap_atomic(page_kaddr);
|
|
|
|
|
|
2020-06-09 04:33:54 +00:00
|
|
|
/* fallback to copy_from_user outside mmap_lock */
|
2015-09-04 22:47:08 +00:00
|
|
|
if (unlikely(ret)) {
|
2018-11-30 22:09:25 +00:00
|
|
|
ret = -ENOENT;
|
2015-09-04 22:47:08 +00:00
|
|
|
*pagep = page;
|
|
|
|
|
/* don't free the page */
|
|
|
|
|
goto out;
|
|
|
|
|
}
|
2022-03-22 21:42:08 +00:00
|
|
|
|
|
|
|
|
flush_dcache_page(page);
|
2015-09-04 22:47:08 +00:00
|
|
|
} else {
|
|
|
|
|
page = *pagep;
|
|
|
|
|
*pagep = NULL;
|
|
|
|
|
}
|
2015-09-04 22:47:04 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* The memory barrier inside __SetPageUptodate makes sure that
|
2019-12-01 01:58:17 +00:00
|
|
|
* preceding stores to the page contents become visible before
|
2015-09-04 22:47:04 +00:00
|
|
|
* the set_pte_at() write.
|
|
|
|
|
*/
|
|
|
|
|
__SetPageUptodate(page);
|
|
|
|
|
|
|
|
|
|
ret = -ENOMEM;
|
2021-06-25 13:27:04 +00:00
|
|
|
if (mem_cgroup_charge(page_folio(page), dst_mm, GFP_KERNEL))
|
2015-09-04 22:47:04 +00:00
|
|
|
goto out_release;
|
|
|
|
|
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
ret = mfill_atomic_install_pte(dst_mm, dst_pmd, dst_vma, dst_addr,
|
|
|
|
|
page, true, wp_copy);
|
|
|
|
|
if (ret)
|
|
|
|
|
goto out_release;
|
2015-09-04 22:47:04 +00:00
|
|
|
out:
|
|
|
|
|
return ret;
|
|
|
|
|
out_release:
|
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-01 12:29:47 +00:00
|
|
|
put_page(page);
|
2015-09-04 22:47:04 +00:00
|
|
|
goto out;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int mfill_zeropage_pte(struct mm_struct *dst_mm,
|
|
|
|
|
pmd_t *dst_pmd,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_addr)
|
|
|
|
|
{
|
|
|
|
|
pte_t _dst_pte, *dst_pte;
|
|
|
|
|
spinlock_t *ptl;
|
|
|
|
|
int ret;
|
2018-11-30 22:09:37 +00:00
|
|
|
pgoff_t offset, max_off;
|
|
|
|
|
struct inode *inode;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
|
|
|
|
_dst_pte = pte_mkspecial(pfn_pte(my_zero_pfn(dst_addr),
|
|
|
|
|
dst_vma->vm_page_prot));
|
|
|
|
|
dst_pte = pte_offset_map_lock(dst_mm, dst_pmd, dst_addr, &ptl);
|
2018-11-30 22:09:37 +00:00
|
|
|
if (dst_vma->vm_file) {
|
|
|
|
|
/* the shmem MAP_PRIVATE case requires checking the i_size */
|
|
|
|
|
inode = dst_vma->vm_file->f_inode;
|
|
|
|
|
offset = linear_page_index(dst_vma, dst_addr);
|
|
|
|
|
max_off = DIV_ROUND_UP(i_size_read(inode), PAGE_SIZE);
|
|
|
|
|
ret = -EFAULT;
|
|
|
|
|
if (unlikely(offset >= max_off))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
}
|
|
|
|
|
ret = -EEXIST;
|
2015-09-04 22:47:04 +00:00
|
|
|
if (!pte_none(*dst_pte))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
set_pte_at(dst_mm, dst_addr, dst_pte, _dst_pte);
|
|
|
|
|
/* No need to invalidate - it was non-present before */
|
|
|
|
|
update_mmu_cache(dst_vma, dst_addr, dst_pte);
|
|
|
|
|
ret = 0;
|
|
|
|
|
out_unlock:
|
|
|
|
|
pte_unmap_unlock(dst_pte, ptl);
|
|
|
|
|
return ret;
|
|
|
|
|
}
|
|
|
|
|
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
/* Handles UFFDIO_CONTINUE for all shmem VMAs (shared or private). */
|
|
|
|
|
static int mcontinue_atomic_pte(struct mm_struct *dst_mm,
|
|
|
|
|
pmd_t *dst_pmd,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_addr,
|
|
|
|
|
bool wp_copy)
|
|
|
|
|
{
|
|
|
|
|
struct inode *inode = file_inode(dst_vma->vm_file);
|
|
|
|
|
pgoff_t pgoff = linear_page_index(dst_vma, dst_addr);
|
|
|
|
|
struct page *page;
|
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
|
|
ret = shmem_getpage(inode, pgoff, &page, SGP_READ);
|
|
|
|
|
if (ret)
|
|
|
|
|
goto out;
|
|
|
|
|
if (!page) {
|
|
|
|
|
ret = -EFAULT;
|
|
|
|
|
goto out;
|
|
|
|
|
}
|
|
|
|
|
|
2022-01-14 22:05:19 +00:00
|
|
|
if (PageHWPoison(page)) {
|
|
|
|
|
ret = -EIO;
|
|
|
|
|
goto out_release;
|
|
|
|
|
}
|
|
|
|
|
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
ret = mfill_atomic_install_pte(dst_mm, dst_pmd, dst_vma, dst_addr,
|
|
|
|
|
page, false, wp_copy);
|
|
|
|
|
if (ret)
|
|
|
|
|
goto out_release;
|
|
|
|
|
|
|
|
|
|
unlock_page(page);
|
|
|
|
|
ret = 0;
|
|
|
|
|
out:
|
|
|
|
|
return ret;
|
|
|
|
|
out_release:
|
|
|
|
|
unlock_page(page);
|
|
|
|
|
put_page(page);
|
|
|
|
|
goto out;
|
|
|
|
|
}
|
|
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
static pmd_t *mm_alloc_pmd(struct mm_struct *mm, unsigned long address)
|
|
|
|
|
{
|
|
|
|
|
pgd_t *pgd;
|
2017-03-09 14:24:07 +00:00
|
|
|
p4d_t *p4d;
|
2015-09-04 22:47:04 +00:00
|
|
|
pud_t *pud;
|
|
|
|
|
|
|
|
|
|
pgd = pgd_offset(mm, address);
|
2017-03-09 14:24:07 +00:00
|
|
|
p4d = p4d_alloc(mm, pgd, address);
|
|
|
|
|
if (!p4d)
|
|
|
|
|
return NULL;
|
|
|
|
|
pud = pud_alloc(mm, p4d, address);
|
|
|
|
|
if (!pud)
|
|
|
|
|
return NULL;
|
|
|
|
|
/*
|
|
|
|
|
* Note that we didn't run this because the pmd was
|
|
|
|
|
* missing, the *pmd may be already established and in
|
|
|
|
|
* turn it may also be a trans_huge_pmd.
|
|
|
|
|
*/
|
|
|
|
|
return pmd_alloc(mm, pud, address);
|
2015-09-04 22:47:04 +00:00
|
|
|
}
|
|
|
|
|
|
2017-02-22 23:42:55 +00:00
|
|
|
#ifdef CONFIG_HUGETLB_PAGE
|
|
|
|
|
/*
|
|
|
|
|
* __mcopy_atomic processing for HUGETLB vmas. Note that this routine is
|
2020-06-09 04:33:54 +00:00
|
|
|
* called with mmap_lock held, it will release mmap_lock before returning.
|
2017-02-22 23:42:55 +00:00
|
|
|
*/
|
|
|
|
|
static __always_inline ssize_t __mcopy_atomic_hugetlb(struct mm_struct *dst_mm,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_start,
|
|
|
|
|
unsigned long src_start,
|
|
|
|
|
unsigned long len,
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
enum mcopy_atomic_mode mode)
|
2017-02-22 23:42:55 +00:00
|
|
|
{
|
2017-02-22 23:43:43 +00:00
|
|
|
int vm_shared = dst_vma->vm_flags & VM_SHARED;
|
2017-02-22 23:42:55 +00:00
|
|
|
ssize_t err;
|
|
|
|
|
pte_t *dst_pte;
|
|
|
|
|
unsigned long src_addr, dst_addr;
|
|
|
|
|
long copied;
|
|
|
|
|
struct page *page;
|
|
|
|
|
unsigned long vma_hpagesize;
|
|
|
|
|
pgoff_t idx;
|
|
|
|
|
u32 hash;
|
|
|
|
|
struct address_space *mapping;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* There is no default zero huge page for all huge page sizes as
|
|
|
|
|
* supported by hugetlb. A PMD_SIZE huge pages may exist as used
|
|
|
|
|
* by THP. Since we can not reliably insert a zero page, this
|
|
|
|
|
* feature is not supported.
|
|
|
|
|
*/
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
if (mode == MCOPY_ATOMIC_ZEROPAGE) {
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2017-02-22 23:42:55 +00:00
|
|
|
return -EINVAL;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
src_addr = src_start;
|
|
|
|
|
dst_addr = dst_start;
|
|
|
|
|
copied = 0;
|
|
|
|
|
page = NULL;
|
|
|
|
|
vma_hpagesize = vma_kernel_pagesize(dst_vma);
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Validate alignment based on huge page size
|
|
|
|
|
*/
|
|
|
|
|
err = -EINVAL;
|
|
|
|
|
if (dst_start & (vma_hpagesize - 1) || len & (vma_hpagesize - 1))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
|
|
|
|
retry:
|
|
|
|
|
/*
|
2020-06-09 04:33:54 +00:00
|
|
|
* On routine entry dst_vma is set. If we had to drop mmap_lock and
|
2017-02-22 23:42:55 +00:00
|
|
|
* retry, dst_vma will be set to NULL and we must lookup again.
|
|
|
|
|
*/
|
|
|
|
|
if (!dst_vma) {
|
2017-02-24 22:58:28 +00:00
|
|
|
err = -ENOENT;
|
2019-12-01 01:57:55 +00:00
|
|
|
dst_vma = find_dst_vma(dst_mm, dst_start, len);
|
2017-02-22 23:42:55 +00:00
|
|
|
if (!dst_vma || !is_vm_hugetlb_page(dst_vma))
|
|
|
|
|
goto out_unlock;
|
2017-02-22 23:43:43 +00:00
|
|
|
|
2017-02-24 22:58:28 +00:00
|
|
|
err = -EINVAL;
|
|
|
|
|
if (vma_hpagesize != vma_kernel_pagesize(dst_vma))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
2017-02-22 23:43:43 +00:00
|
|
|
vm_shared = dst_vma->vm_flags & VM_SHARED;
|
2017-02-22 23:42:55 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/*
|
2017-02-22 23:43:43 +00:00
|
|
|
* If not shared, ensure the dst_vma has a anon_vma.
|
2017-02-22 23:42:55 +00:00
|
|
|
*/
|
|
|
|
|
err = -ENOMEM;
|
2017-02-22 23:43:43 +00:00
|
|
|
if (!vm_shared) {
|
|
|
|
|
if (unlikely(anon_vma_prepare(dst_vma)))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
}
|
2017-02-22 23:42:55 +00:00
|
|
|
|
|
|
|
|
while (src_addr < src_start + len) {
|
|
|
|
|
BUG_ON(dst_addr >= dst_start + len);
|
|
|
|
|
|
|
|
|
|
/*
|
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2.
While discussing the issue with huge_pte_offset [1], I remembered that
there were more outstanding hugetlb races. These issues are:
1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become
invalid via a call to huge_pmd_unshare by another thread.
2) hugetlbfs page faults can race with truncation causing invalid global
reserve counts and state.
A previous attempt was made to use i_mmap_rwsem in this manner as
described at [2]. However, those patches were reverted starting with [3]
due to locking issues.
To effectively use i_mmap_rwsem to address the above issues it needs to be
held (in read mode) during page fault processing. However, during fault
processing we need to lock the page we will be adding. Lock ordering
requires we take page lock before i_mmap_rwsem. Waiting until after
taking the page lock is too late in the fault process for the
synchronization we want to do.
To address this lock ordering issue, the following patches change the lock
ordering for hugetlb pages. This is not too invasive as hugetlbfs
processing is done separate from core mm in many places. However, I don't
really like this idea. Much ugliness is contained in the new routine
hugetlb_page_mapping_lock_write() of patch 1.
The only other way I can think of to address these issues is by catching
all the races. After catching a race, cleanup, backout, retry ... etc,
as needed. This can get really ugly, especially for huge page
reservations. At one time, I started writing some of the reservation
backout code for page faults and it got so ugly and complicated I went
down the path of adding synchronization to avoid the races. Any other
suggestions would be welcome.
[1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/
[2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/
[3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com
[4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/
[5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/
This patch (of 2):
While looking at BUGs associated with invalid huge page map counts, it was
discovered and observed that a huge pte pointer could become 'invalid' and
point to another task's page table. Consider the following:
A task takes a page fault on a shared hugetlbfs file and calls
huge_pte_alloc to get a ptep. Suppose the returned ptep points to a
shared pmd.
Now, another task truncates the hugetlbfs file. As part of truncation, it
unmaps everyone who has the file mapped. If the range being truncated is
covered by a shared pmd, huge_pmd_unshare will be called. For all but the
last user of the shared pmd, huge_pmd_unshare will clear the pud pointing
to the pmd. If the task in the middle of the page fault is not the last
user, the ptep returned by huge_pte_alloc now points to another task's
page table or worse. This leads to bad things such as incorrect page
map/reference counts or invalid memory references.
To fix, expand the use of i_mmap_rwsem as follows:
- i_mmap_rwsem is held in read mode whenever huge_pmd_share is called.
huge_pmd_share is only called via huge_pte_alloc, so callers of
huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers
of huge_pte_alloc continue to hold the semaphore until finished with
the ptep.
- i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called.
One problem with this scheme is that it requires taking i_mmap_rwsem
before taking the page lock during page faults. This is not the order
specified in the rest of mm code. Handling of hugetlbfs pages is mostly
isolated today. Therefore, we use this alternative locking order for
PageHuge() pages.
mapping->i_mmap_rwsem
hugetlb_fault_mutex (hugetlbfs specific page fault mutex)
page->flags PG_locked (lock_page)
To help with lock ordering issues, hugetlb_page_mapping_lock_write() is
introduced to write lock the i_mmap_rwsem associated with a page.
In most cases it is easy to get address_space via vma->vm_file->f_mapping.
However, in the case of migration or memory errors for anon pages we do
not have an associated vma. A new routine _get_hugetlb_page_mapping()
will use anon_vma to get address_space in these cases.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
|
|
|
* Serialize via i_mmap_rwsem and hugetlb_fault_mutex.
|
|
|
|
|
* i_mmap_rwsem ensures the dst_pte remains valid even
|
|
|
|
|
* in the case of shared pmds. fault mutex prevents
|
|
|
|
|
* races with other faulting threads.
|
2017-02-22 23:42:55 +00:00
|
|
|
*/
|
2019-01-08 23:23:36 +00:00
|
|
|
mapping = dst_vma->vm_file->f_mapping;
|
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2.
While discussing the issue with huge_pte_offset [1], I remembered that
there were more outstanding hugetlb races. These issues are:
1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become
invalid via a call to huge_pmd_unshare by another thread.
2) hugetlbfs page faults can race with truncation causing invalid global
reserve counts and state.
A previous attempt was made to use i_mmap_rwsem in this manner as
described at [2]. However, those patches were reverted starting with [3]
due to locking issues.
To effectively use i_mmap_rwsem to address the above issues it needs to be
held (in read mode) during page fault processing. However, during fault
processing we need to lock the page we will be adding. Lock ordering
requires we take page lock before i_mmap_rwsem. Waiting until after
taking the page lock is too late in the fault process for the
synchronization we want to do.
To address this lock ordering issue, the following patches change the lock
ordering for hugetlb pages. This is not too invasive as hugetlbfs
processing is done separate from core mm in many places. However, I don't
really like this idea. Much ugliness is contained in the new routine
hugetlb_page_mapping_lock_write() of patch 1.
The only other way I can think of to address these issues is by catching
all the races. After catching a race, cleanup, backout, retry ... etc,
as needed. This can get really ugly, especially for huge page
reservations. At one time, I started writing some of the reservation
backout code for page faults and it got so ugly and complicated I went
down the path of adding synchronization to avoid the races. Any other
suggestions would be welcome.
[1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/
[2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/
[3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com
[4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/
[5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/
This patch (of 2):
While looking at BUGs associated with invalid huge page map counts, it was
discovered and observed that a huge pte pointer could become 'invalid' and
point to another task's page table. Consider the following:
A task takes a page fault on a shared hugetlbfs file and calls
huge_pte_alloc to get a ptep. Suppose the returned ptep points to a
shared pmd.
Now, another task truncates the hugetlbfs file. As part of truncation, it
unmaps everyone who has the file mapped. If the range being truncated is
covered by a shared pmd, huge_pmd_unshare will be called. For all but the
last user of the shared pmd, huge_pmd_unshare will clear the pud pointing
to the pmd. If the task in the middle of the page fault is not the last
user, the ptep returned by huge_pte_alloc now points to another task's
page table or worse. This leads to bad things such as incorrect page
map/reference counts or invalid memory references.
To fix, expand the use of i_mmap_rwsem as follows:
- i_mmap_rwsem is held in read mode whenever huge_pmd_share is called.
huge_pmd_share is only called via huge_pte_alloc, so callers of
huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers
of huge_pte_alloc continue to hold the semaphore until finished with
the ptep.
- i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called.
One problem with this scheme is that it requires taking i_mmap_rwsem
before taking the page lock during page faults. This is not the order
specified in the rest of mm code. Handling of hugetlbfs pages is mostly
isolated today. Therefore, we use this alternative locking order for
PageHuge() pages.
mapping->i_mmap_rwsem
hugetlb_fault_mutex (hugetlbfs specific page fault mutex)
page->flags PG_locked (lock_page)
To help with lock ordering issues, hugetlb_page_mapping_lock_write() is
introduced to write lock the i_mmap_rwsem associated with a page.
In most cases it is easy to get address_space via vma->vm_file->f_mapping.
However, in the case of migration or memory errors for anon pages we do
not have an associated vma. A new routine _get_hugetlb_page_mapping()
will use anon_vma to get address_space in these cases.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
|
|
|
i_mmap_lock_read(mapping);
|
|
|
|
|
idx = linear_page_index(dst_vma, dst_addr);
|
2019-12-01 01:57:02 +00:00
|
|
|
hash = hugetlb_fault_mutex_hash(mapping, idx);
|
2017-02-22 23:42:55 +00:00
|
|
|
mutex_lock(&hugetlb_fault_mutex_table[hash]);
|
|
|
|
|
|
|
|
|
|
err = -ENOMEM;
|
2021-05-05 01:33:00 +00:00
|
|
|
dst_pte = huge_pte_alloc(dst_mm, dst_vma, dst_addr, vma_hpagesize);
|
2017-02-22 23:42:55 +00:00
|
|
|
if (!dst_pte) {
|
|
|
|
|
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
|
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2.
While discussing the issue with huge_pte_offset [1], I remembered that
there were more outstanding hugetlb races. These issues are:
1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become
invalid via a call to huge_pmd_unshare by another thread.
2) hugetlbfs page faults can race with truncation causing invalid global
reserve counts and state.
A previous attempt was made to use i_mmap_rwsem in this manner as
described at [2]. However, those patches were reverted starting with [3]
due to locking issues.
To effectively use i_mmap_rwsem to address the above issues it needs to be
held (in read mode) during page fault processing. However, during fault
processing we need to lock the page we will be adding. Lock ordering
requires we take page lock before i_mmap_rwsem. Waiting until after
taking the page lock is too late in the fault process for the
synchronization we want to do.
To address this lock ordering issue, the following patches change the lock
ordering for hugetlb pages. This is not too invasive as hugetlbfs
processing is done separate from core mm in many places. However, I don't
really like this idea. Much ugliness is contained in the new routine
hugetlb_page_mapping_lock_write() of patch 1.
The only other way I can think of to address these issues is by catching
all the races. After catching a race, cleanup, backout, retry ... etc,
as needed. This can get really ugly, especially for huge page
reservations. At one time, I started writing some of the reservation
backout code for page faults and it got so ugly and complicated I went
down the path of adding synchronization to avoid the races. Any other
suggestions would be welcome.
[1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/
[2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/
[3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com
[4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/
[5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/
This patch (of 2):
While looking at BUGs associated with invalid huge page map counts, it was
discovered and observed that a huge pte pointer could become 'invalid' and
point to another task's page table. Consider the following:
A task takes a page fault on a shared hugetlbfs file and calls
huge_pte_alloc to get a ptep. Suppose the returned ptep points to a
shared pmd.
Now, another task truncates the hugetlbfs file. As part of truncation, it
unmaps everyone who has the file mapped. If the range being truncated is
covered by a shared pmd, huge_pmd_unshare will be called. For all but the
last user of the shared pmd, huge_pmd_unshare will clear the pud pointing
to the pmd. If the task in the middle of the page fault is not the last
user, the ptep returned by huge_pte_alloc now points to another task's
page table or worse. This leads to bad things such as incorrect page
map/reference counts or invalid memory references.
To fix, expand the use of i_mmap_rwsem as follows:
- i_mmap_rwsem is held in read mode whenever huge_pmd_share is called.
huge_pmd_share is only called via huge_pte_alloc, so callers of
huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers
of huge_pte_alloc continue to hold the semaphore until finished with
the ptep.
- i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called.
One problem with this scheme is that it requires taking i_mmap_rwsem
before taking the page lock during page faults. This is not the order
specified in the rest of mm code. Handling of hugetlbfs pages is mostly
isolated today. Therefore, we use this alternative locking order for
PageHuge() pages.
mapping->i_mmap_rwsem
hugetlb_fault_mutex (hugetlbfs specific page fault mutex)
page->flags PG_locked (lock_page)
To help with lock ordering issues, hugetlb_page_mapping_lock_write() is
introduced to write lock the i_mmap_rwsem associated with a page.
In most cases it is easy to get address_space via vma->vm_file->f_mapping.
However, in the case of migration or memory errors for anon pages we do
not have an associated vma. A new routine _get_hugetlb_page_mapping()
will use anon_vma to get address_space in these cases.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
|
|
|
i_mmap_unlock_read(mapping);
|
2017-02-22 23:42:55 +00:00
|
|
|
goto out_unlock;
|
|
|
|
|
}
|
|
|
|
|
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
if (mode != MCOPY_ATOMIC_CONTINUE &&
|
|
|
|
|
!huge_pte_none(huge_ptep_get(dst_pte))) {
|
|
|
|
|
err = -EEXIST;
|
2017-02-22 23:42:55 +00:00
|
|
|
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
|
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2.
While discussing the issue with huge_pte_offset [1], I remembered that
there were more outstanding hugetlb races. These issues are:
1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become
invalid via a call to huge_pmd_unshare by another thread.
2) hugetlbfs page faults can race with truncation causing invalid global
reserve counts and state.
A previous attempt was made to use i_mmap_rwsem in this manner as
described at [2]. However, those patches were reverted starting with [3]
due to locking issues.
To effectively use i_mmap_rwsem to address the above issues it needs to be
held (in read mode) during page fault processing. However, during fault
processing we need to lock the page we will be adding. Lock ordering
requires we take page lock before i_mmap_rwsem. Waiting until after
taking the page lock is too late in the fault process for the
synchronization we want to do.
To address this lock ordering issue, the following patches change the lock
ordering for hugetlb pages. This is not too invasive as hugetlbfs
processing is done separate from core mm in many places. However, I don't
really like this idea. Much ugliness is contained in the new routine
hugetlb_page_mapping_lock_write() of patch 1.
The only other way I can think of to address these issues is by catching
all the races. After catching a race, cleanup, backout, retry ... etc,
as needed. This can get really ugly, especially for huge page
reservations. At one time, I started writing some of the reservation
backout code for page faults and it got so ugly and complicated I went
down the path of adding synchronization to avoid the races. Any other
suggestions would be welcome.
[1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/
[2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/
[3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com
[4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/
[5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/
This patch (of 2):
While looking at BUGs associated with invalid huge page map counts, it was
discovered and observed that a huge pte pointer could become 'invalid' and
point to another task's page table. Consider the following:
A task takes a page fault on a shared hugetlbfs file and calls
huge_pte_alloc to get a ptep. Suppose the returned ptep points to a
shared pmd.
Now, another task truncates the hugetlbfs file. As part of truncation, it
unmaps everyone who has the file mapped. If the range being truncated is
covered by a shared pmd, huge_pmd_unshare will be called. For all but the
last user of the shared pmd, huge_pmd_unshare will clear the pud pointing
to the pmd. If the task in the middle of the page fault is not the last
user, the ptep returned by huge_pte_alloc now points to another task's
page table or worse. This leads to bad things such as incorrect page
map/reference counts or invalid memory references.
To fix, expand the use of i_mmap_rwsem as follows:
- i_mmap_rwsem is held in read mode whenever huge_pmd_share is called.
huge_pmd_share is only called via huge_pte_alloc, so callers of
huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers
of huge_pte_alloc continue to hold the semaphore until finished with
the ptep.
- i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called.
One problem with this scheme is that it requires taking i_mmap_rwsem
before taking the page lock during page faults. This is not the order
specified in the rest of mm code. Handling of hugetlbfs pages is mostly
isolated today. Therefore, we use this alternative locking order for
PageHuge() pages.
mapping->i_mmap_rwsem
hugetlb_fault_mutex (hugetlbfs specific page fault mutex)
page->flags PG_locked (lock_page)
To help with lock ordering issues, hugetlb_page_mapping_lock_write() is
introduced to write lock the i_mmap_rwsem associated with a page.
In most cases it is easy to get address_space via vma->vm_file->f_mapping.
However, in the case of migration or memory errors for anon pages we do
not have an associated vma. A new routine _get_hugetlb_page_mapping()
will use anon_vma to get address_space in these cases.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
|
|
|
i_mmap_unlock_read(mapping);
|
2017-02-22 23:42:55 +00:00
|
|
|
goto out_unlock;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
err = hugetlb_mcopy_atomic_pte(dst_mm, dst_pte, dst_vma,
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
dst_addr, src_addr, mode, &page);
|
2017-02-22 23:42:55 +00:00
|
|
|
|
|
|
|
|
mutex_unlock(&hugetlb_fault_mutex_table[hash]);
|
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
Patch series "hugetlbfs: use i_mmap_rwsem for more synchronization", v2.
While discussing the issue with huge_pte_offset [1], I remembered that
there were more outstanding hugetlb races. These issues are:
1) For shared pmds, huge PTE pointers returned by huge_pte_alloc can become
invalid via a call to huge_pmd_unshare by another thread.
2) hugetlbfs page faults can race with truncation causing invalid global
reserve counts and state.
A previous attempt was made to use i_mmap_rwsem in this manner as
described at [2]. However, those patches were reverted starting with [3]
due to locking issues.
To effectively use i_mmap_rwsem to address the above issues it needs to be
held (in read mode) during page fault processing. However, during fault
processing we need to lock the page we will be adding. Lock ordering
requires we take page lock before i_mmap_rwsem. Waiting until after
taking the page lock is too late in the fault process for the
synchronization we want to do.
To address this lock ordering issue, the following patches change the lock
ordering for hugetlb pages. This is not too invasive as hugetlbfs
processing is done separate from core mm in many places. However, I don't
really like this idea. Much ugliness is contained in the new routine
hugetlb_page_mapping_lock_write() of patch 1.
The only other way I can think of to address these issues is by catching
all the races. After catching a race, cleanup, backout, retry ... etc,
as needed. This can get really ugly, especially for huge page
reservations. At one time, I started writing some of the reservation
backout code for page faults and it got so ugly and complicated I went
down the path of adding synchronization to avoid the races. Any other
suggestions would be welcome.
[1] https://lore.kernel.org/linux-mm/1582342427-230392-1-git-send-email-longpeng2@huawei.com/
[2] https://lore.kernel.org/linux-mm/20181222223013.22193-1-mike.kravetz@oracle.com/
[3] https://lore.kernel.org/linux-mm/20190103235452.29335-1-mike.kravetz@oracle.com
[4] https://lore.kernel.org/linux-mm/1584028670.7365.182.camel@lca.pw/
[5] https://lore.kernel.org/lkml/20200312183142.108df9ac@canb.auug.org.au/
This patch (of 2):
While looking at BUGs associated with invalid huge page map counts, it was
discovered and observed that a huge pte pointer could become 'invalid' and
point to another task's page table. Consider the following:
A task takes a page fault on a shared hugetlbfs file and calls
huge_pte_alloc to get a ptep. Suppose the returned ptep points to a
shared pmd.
Now, another task truncates the hugetlbfs file. As part of truncation, it
unmaps everyone who has the file mapped. If the range being truncated is
covered by a shared pmd, huge_pmd_unshare will be called. For all but the
last user of the shared pmd, huge_pmd_unshare will clear the pud pointing
to the pmd. If the task in the middle of the page fault is not the last
user, the ptep returned by huge_pte_alloc now points to another task's
page table or worse. This leads to bad things such as incorrect page
map/reference counts or invalid memory references.
To fix, expand the use of i_mmap_rwsem as follows:
- i_mmap_rwsem is held in read mode whenever huge_pmd_share is called.
huge_pmd_share is only called via huge_pte_alloc, so callers of
huge_pte_alloc take i_mmap_rwsem before calling. In addition, callers
of huge_pte_alloc continue to hold the semaphore until finished with
the ptep.
- i_mmap_rwsem is held in write mode whenever huge_pmd_unshare is called.
One problem with this scheme is that it requires taking i_mmap_rwsem
before taking the page lock during page faults. This is not the order
specified in the rest of mm code. Handling of hugetlbfs pages is mostly
isolated today. Therefore, we use this alternative locking order for
PageHuge() pages.
mapping->i_mmap_rwsem
hugetlb_fault_mutex (hugetlbfs specific page fault mutex)
page->flags PG_locked (lock_page)
To help with lock ordering issues, hugetlb_page_mapping_lock_write() is
introduced to write lock the i_mmap_rwsem associated with a page.
In most cases it is easy to get address_space via vma->vm_file->f_mapping.
However, in the case of migration or memory errors for anon pages we do
not have an associated vma. A new routine _get_hugetlb_page_mapping()
will use anon_vma to get address_space in these cases.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Link: http://lkml.kernel.org/r/20200316205756.146666-2-mike.kravetz@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-04-02 04:11:05 +00:00
|
|
|
i_mmap_unlock_read(mapping);
|
2017-02-22 23:42:55 +00:00
|
|
|
|
|
|
|
|
cond_resched();
|
|
|
|
|
|
2018-11-30 22:09:25 +00:00
|
|
|
if (unlikely(err == -ENOENT)) {
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2017-02-22 23:42:55 +00:00
|
|
|
BUG_ON(!page);
|
|
|
|
|
|
|
|
|
|
err = copy_huge_page_from_user(page,
|
|
|
|
|
(const void __user *)src_addr,
|
2019-12-01 01:57:49 +00:00
|
|
|
vma_hpagesize / PAGE_SIZE,
|
|
|
|
|
true);
|
2017-02-22 23:42:55 +00:00
|
|
|
if (unlikely(err)) {
|
|
|
|
|
err = -EFAULT;
|
|
|
|
|
goto out;
|
|
|
|
|
}
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_lock(dst_mm);
|
2017-02-22 23:42:55 +00:00
|
|
|
|
|
|
|
|
dst_vma = NULL;
|
|
|
|
|
goto retry;
|
|
|
|
|
} else
|
|
|
|
|
BUG_ON(page);
|
|
|
|
|
|
|
|
|
|
if (!err) {
|
|
|
|
|
dst_addr += vma_hpagesize;
|
|
|
|
|
src_addr += vma_hpagesize;
|
|
|
|
|
copied += vma_hpagesize;
|
|
|
|
|
|
|
|
|
|
if (fatal_signal_pending(current))
|
|
|
|
|
err = -EINTR;
|
|
|
|
|
}
|
|
|
|
|
if (err)
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
out_unlock:
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2017-02-22 23:42:55 +00:00
|
|
|
out:
|
mm, hugetlb: fix racy resv_huge_pages underflow on UFFDIO_COPY
On UFFDIO_COPY, if we fail to copy the page contents while holding the
hugetlb_fault_mutex, we will drop the mutex and return to the caller after
allocating a page that consumed a reservation. In this case there may be
a fault that double consumes the reservation. To handle this, we free the
allocated page, fix the reservations, and allocate a temporary hugetlb
page and return that to the caller. When the caller does the copy outside
of the lock, we again check the cache, and allocate a page consuming the
reservation, and copy over the contents.
Test:
Hacked the code locally such that resv_huge_pages underflows produce
a warning and the copy_huge_page_from_user() always fails, then:
./tools/testing/selftests/vm/userfaultfd hugetlb_shared 10
2 /tmp/kokonut_test/huge/userfaultfd_test && echo test success
./tools/testing/selftests/vm/userfaultfd hugetlb 10
2 /tmp/kokonut_test/huge/userfaultfd_test && echo test success
Both tests succeed and produce no warnings. After the
test runs number of free/resv hugepages is correct.
[yuehaibing@huawei.com: remove set but not used variable 'vm_alloc_shared']
Link: https://lkml.kernel.org/r/20210601141610.28332-1-yuehaibing@huawei.com
[almasrymina@google.com: fix allocation error check and copy func name]
Link: https://lkml.kernel.org/r/20210605010626.1459873-1-almasrymina@google.com
Link: https://lkml.kernel.org/r/20210528005029.88088-1-almasrymina@google.com
Signed-off-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:48:19 +00:00
|
|
|
if (page)
|
2017-02-22 23:42:55 +00:00
|
|
|
put_page(page);
|
|
|
|
|
BUG_ON(copied < 0);
|
|
|
|
|
BUG_ON(err > 0);
|
|
|
|
|
BUG_ON(!copied && !err);
|
|
|
|
|
return copied ? copied : err;
|
|
|
|
|
}
|
|
|
|
|
#else /* !CONFIG_HUGETLB_PAGE */
|
|
|
|
|
/* fail at build time if gcc attempts to use this */
|
|
|
|
|
extern ssize_t __mcopy_atomic_hugetlb(struct mm_struct *dst_mm,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_start,
|
|
|
|
|
unsigned long src_start,
|
|
|
|
|
unsigned long len,
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
enum mcopy_atomic_mode mode);
|
2017-02-22 23:42:55 +00:00
|
|
|
#endif /* CONFIG_HUGETLB_PAGE */
|
|
|
|
|
|
2017-09-06 23:23:06 +00:00
|
|
|
static __always_inline ssize_t mfill_atomic_pte(struct mm_struct *dst_mm,
|
|
|
|
|
pmd_t *dst_pmd,
|
|
|
|
|
struct vm_area_struct *dst_vma,
|
|
|
|
|
unsigned long dst_addr,
|
|
|
|
|
unsigned long src_addr,
|
|
|
|
|
struct page **page,
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
enum mcopy_atomic_mode mode,
|
2020-04-07 03:05:41 +00:00
|
|
|
bool wp_copy)
|
2017-09-06 23:23:06 +00:00
|
|
|
{
|
|
|
|
|
ssize_t err;
|
|
|
|
|
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
if (mode == MCOPY_ATOMIC_CONTINUE) {
|
|
|
|
|
return mcontinue_atomic_pte(dst_mm, dst_pmd, dst_vma, dst_addr,
|
|
|
|
|
wp_copy);
|
|
|
|
|
}
|
|
|
|
|
|
2018-11-30 22:09:28 +00:00
|
|
|
/*
|
|
|
|
|
* The normal page fault path for a shmem will invoke the
|
|
|
|
|
* fault, fill the hole in the file and COW it right away. The
|
|
|
|
|
* result generates plain anonymous memory. So when we are
|
|
|
|
|
* asked to fill an hole in a MAP_PRIVATE shmem mapping, we'll
|
|
|
|
|
* generate anonymous memory directly without actually filling
|
|
|
|
|
* the hole. For the MAP_PRIVATE case the robustness check
|
|
|
|
|
* only happens in the pagetable (to verify it's still none)
|
|
|
|
|
* and not in the radix tree.
|
|
|
|
|
*/
|
|
|
|
|
if (!(dst_vma->vm_flags & VM_SHARED)) {
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
if (mode == MCOPY_ATOMIC_NORMAL)
|
2017-09-06 23:23:06 +00:00
|
|
|
err = mcopy_atomic_pte(dst_mm, dst_pmd, dst_vma,
|
2020-04-07 03:05:41 +00:00
|
|
|
dst_addr, src_addr, page,
|
|
|
|
|
wp_copy);
|
2017-09-06 23:23:06 +00:00
|
|
|
else
|
|
|
|
|
err = mfill_zeropage_pte(dst_mm, dst_pmd,
|
|
|
|
|
dst_vma, dst_addr);
|
|
|
|
|
} else {
|
2020-04-07 03:05:41 +00:00
|
|
|
VM_WARN_ON_ONCE(wp_copy);
|
userfaultfd/shmem: combine shmem_{mcopy_atomic,mfill_zeropage}_pte
Patch series "userfaultfd: add minor fault handling for shmem", v6.
Overview
========
See the series which added minor faults for hugetlbfs [3] for a detailed
overview of minor fault handling in general. This series adds the same
support for shmem-backed areas.
This series is structured as follows:
- Commits 1 and 2 are cleanups.
- Commits 3 and 4 implement the new feature (minor fault handling for shmem).
- Commit 5 advertises that the feature is now available since at this point it's
fully implemented.
- Commit 6 is a final cleanup, modifying an existing code path to re-use a new
helper we've introduced.
- Commits 7, 8, 9, 10 update the userfaultfd selftest to exercise the feature.
Use Case
========
In some cases it is useful to have VM memory backed by tmpfs instead of
hugetlbfs. So, this feature will be used to support the same VM live
migration use case described in my original series.
Additionally, Android folks (Lokesh Gidra <lokeshgidra@google.com>) hope
to optimize the Android Runtime garbage collector using this feature:
"The plan is to use userfaultfd for concurrently compacting the heap.
With this feature, the heap can be shared-mapped at another location where
the GC-thread(s) could continue the compaction operation without the need
to invoke userfault ioctl(UFFDIO_COPY) each time. OTOH, if and when Java
threads get faults on the heap, UFFDIO_CONTINUE can be used to resume
execution. Furthermore, this feature enables updating references in the
'non-moving' portion of the heap efficiently. Without this feature,
uneccessary page copying (ioctl(UFFDIO_COPY)) would be required."
[1] https://lore.kernel.org/patchwork/cover/1388144/
[2] https://lore.kernel.org/patchwork/patch/1408161/
[3] https://lore.kernel.org/linux-fsdevel/20210301222728.176417-1-axelrasmussen@google.com/T/#t
This patch (of 9):
Previously, we did a dance where we had one calling path in userfaultfd.c
(mfill_atomic_pte), but then we split it into two in shmem_fs.h
(shmem_{mcopy_atomic,mfill_zeropage}_pte), and then rejoined into a single
shared function in shmem.c (shmem_mfill_atomic_pte).
This is all a bit overly complex. Just call the single combined shmem
function directly, allowing us to clean up various branches, boilerplate,
etc.
While we're touching this function, two other small cleanup changes:
- offset is equivalent to pgoff, so we can get rid of offset entirely.
- Split two VM_BUG_ON cases into two statements. This means the line
number reported when the BUG is hit specifies exactly which condition
was true.
Link: https://lkml.kernel.org/r/20210503180737.2487560-1-axelrasmussen@google.com
Link: https://lkml.kernel.org/r/20210503180737.2487560-3-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:17 +00:00
|
|
|
err = shmem_mfill_atomic_pte(dst_mm, dst_pmd, dst_vma,
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
dst_addr, src_addr,
|
|
|
|
|
mode != MCOPY_ATOMIC_NORMAL,
|
userfaultfd/shmem: combine shmem_{mcopy_atomic,mfill_zeropage}_pte
Patch series "userfaultfd: add minor fault handling for shmem", v6.
Overview
========
See the series which added minor faults for hugetlbfs [3] for a detailed
overview of minor fault handling in general. This series adds the same
support for shmem-backed areas.
This series is structured as follows:
- Commits 1 and 2 are cleanups.
- Commits 3 and 4 implement the new feature (minor fault handling for shmem).
- Commit 5 advertises that the feature is now available since at this point it's
fully implemented.
- Commit 6 is a final cleanup, modifying an existing code path to re-use a new
helper we've introduced.
- Commits 7, 8, 9, 10 update the userfaultfd selftest to exercise the feature.
Use Case
========
In some cases it is useful to have VM memory backed by tmpfs instead of
hugetlbfs. So, this feature will be used to support the same VM live
migration use case described in my original series.
Additionally, Android folks (Lokesh Gidra <lokeshgidra@google.com>) hope
to optimize the Android Runtime garbage collector using this feature:
"The plan is to use userfaultfd for concurrently compacting the heap.
With this feature, the heap can be shared-mapped at another location where
the GC-thread(s) could continue the compaction operation without the need
to invoke userfault ioctl(UFFDIO_COPY) each time. OTOH, if and when Java
threads get faults on the heap, UFFDIO_CONTINUE can be used to resume
execution. Furthermore, this feature enables updating references in the
'non-moving' portion of the heap efficiently. Without this feature,
uneccessary page copying (ioctl(UFFDIO_COPY)) would be required."
[1] https://lore.kernel.org/patchwork/cover/1388144/
[2] https://lore.kernel.org/patchwork/patch/1408161/
[3] https://lore.kernel.org/linux-fsdevel/20210301222728.176417-1-axelrasmussen@google.com/T/#t
This patch (of 9):
Previously, we did a dance where we had one calling path in userfaultfd.c
(mfill_atomic_pte), but then we split it into two in shmem_fs.h
(shmem_{mcopy_atomic,mfill_zeropage}_pte), and then rejoined into a single
shared function in shmem.c (shmem_mfill_atomic_pte).
This is all a bit overly complex. Just call the single combined shmem
function directly, allowing us to clean up various branches, boilerplate,
etc.
While we're touching this function, two other small cleanup changes:
- offset is equivalent to pgoff, so we can get rid of offset entirely.
- Split two VM_BUG_ON cases into two statements. This means the line
number reported when the BUG is hit specifies exactly which condition
was true.
Link: https://lkml.kernel.org/r/20210503180737.2487560-1-axelrasmussen@google.com
Link: https://lkml.kernel.org/r/20210503180737.2487560-3-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:17 +00:00
|
|
|
page);
|
2017-09-06 23:23:06 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
return err;
|
|
|
|
|
}
|
|
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
static __always_inline ssize_t __mcopy_atomic(struct mm_struct *dst_mm,
|
|
|
|
|
unsigned long dst_start,
|
|
|
|
|
unsigned long src_start,
|
|
|
|
|
unsigned long len,
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
enum mcopy_atomic_mode mcopy_mode,
|
2021-09-02 21:58:56 +00:00
|
|
|
atomic_t *mmap_changing,
|
2020-04-07 03:05:41 +00:00
|
|
|
__u64 mode)
|
2015-09-04 22:47:04 +00:00
|
|
|
{
|
|
|
|
|
struct vm_area_struct *dst_vma;
|
|
|
|
|
ssize_t err;
|
|
|
|
|
pmd_t *dst_pmd;
|
|
|
|
|
unsigned long src_addr, dst_addr;
|
2015-09-04 22:47:08 +00:00
|
|
|
long copied;
|
|
|
|
|
struct page *page;
|
2020-04-07 03:05:41 +00:00
|
|
|
bool wp_copy;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Sanitize the command parameters:
|
|
|
|
|
*/
|
|
|
|
|
BUG_ON(dst_start & ~PAGE_MASK);
|
|
|
|
|
BUG_ON(len & ~PAGE_MASK);
|
|
|
|
|
|
|
|
|
|
/* Does the address range wrap, or is the span zero-sized? */
|
|
|
|
|
BUG_ON(src_start + len <= src_start);
|
|
|
|
|
BUG_ON(dst_start + len <= dst_start);
|
|
|
|
|
|
2015-09-04 22:47:08 +00:00
|
|
|
src_addr = src_start;
|
|
|
|
|
dst_addr = dst_start;
|
|
|
|
|
copied = 0;
|
|
|
|
|
page = NULL;
|
|
|
|
|
retry:
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_lock(dst_mm);
|
2015-09-04 22:47:04 +00:00
|
|
|
|
userfaultfd: prevent non-cooperative events vs mcopy_atomic races
If a process monitored with userfaultfd changes it's memory mappings or
forks() at the same time as uffd monitor fills the process memory with
UFFDIO_COPY, the actual creation of page table entries and copying of
the data in mcopy_atomic may happen either before of after the memory
mapping modifications and there is no way for the uffd monitor to
maintain consistent view of the process memory layout.
For instance, let's consider fork() running in parallel with
userfaultfd_copy():
process | uffd monitor
---------------------------------+------------------------------
fork() | userfaultfd_copy()
... | ...
dup_mmap() | down_read(mmap_sem)
down_write(mmap_sem) | /* create PTEs, copy data */
dup_uffd() | up_read(mmap_sem)
copy_page_range() |
up_write(mmap_sem) |
dup_uffd_complete() |
/* notify monitor */ |
If the userfaultfd_copy() takes the mmap_sem first, the new page(s) will
be present by the time copy_page_range() is called and they will appear
in the child's memory mappings. However, if the fork() is the first to
take the mmap_sem, the new pages won't be mapped in the child's address
space.
If the pages are not present and child tries to access them, the monitor
will get page fault notification and everything is fine. However, if
the pages *are present*, the child can access them without uffd
noticing. And if we copy them into child it'll see the wrong data.
Since we are talking about background copy, we'd need to decide whether
the pages should be copied or not regardless #PF notifications.
Since userfaultfd monitor has no way to determine what was the order,
let's disallow userfaultfd_copy in parallel with the non-cooperative
events. In such case we return -EAGAIN and the uffd monitor can
understand that userfaultfd_copy() clashed with a non-cooperative event
and take an appropriate action.
Link: http://lkml.kernel.org/r/1527061324-19949-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-08 00:09:25 +00:00
|
|
|
/*
|
|
|
|
|
* If memory mappings are changing because of non-cooperative
|
|
|
|
|
* operation (e.g. mremap) running in parallel, bail out and
|
|
|
|
|
* request the user to retry later
|
|
|
|
|
*/
|
|
|
|
|
err = -EAGAIN;
|
2021-09-02 21:58:56 +00:00
|
|
|
if (mmap_changing && atomic_read(mmap_changing))
|
userfaultfd: prevent non-cooperative events vs mcopy_atomic races
If a process monitored with userfaultfd changes it's memory mappings or
forks() at the same time as uffd monitor fills the process memory with
UFFDIO_COPY, the actual creation of page table entries and copying of
the data in mcopy_atomic may happen either before of after the memory
mapping modifications and there is no way for the uffd monitor to
maintain consistent view of the process memory layout.
For instance, let's consider fork() running in parallel with
userfaultfd_copy():
process | uffd monitor
---------------------------------+------------------------------
fork() | userfaultfd_copy()
... | ...
dup_mmap() | down_read(mmap_sem)
down_write(mmap_sem) | /* create PTEs, copy data */
dup_uffd() | up_read(mmap_sem)
copy_page_range() |
up_write(mmap_sem) |
dup_uffd_complete() |
/* notify monitor */ |
If the userfaultfd_copy() takes the mmap_sem first, the new page(s) will
be present by the time copy_page_range() is called and they will appear
in the child's memory mappings. However, if the fork() is the first to
take the mmap_sem, the new pages won't be mapped in the child's address
space.
If the pages are not present and child tries to access them, the monitor
will get page fault notification and everything is fine. However, if
the pages *are present*, the child can access them without uffd
noticing. And if we copy them into child it'll see the wrong data.
Since we are talking about background copy, we'd need to decide whether
the pages should be copied or not regardless #PF notifications.
Since userfaultfd monitor has no way to determine what was the order,
let's disallow userfaultfd_copy in parallel with the non-cooperative
events. In such case we return -EAGAIN and the uffd monitor can
understand that userfaultfd_copy() clashed with a non-cooperative event
and take an appropriate action.
Link: http://lkml.kernel.org/r/1527061324-19949-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-08 00:09:25 +00:00
|
|
|
goto out_unlock;
|
|
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
/*
|
|
|
|
|
* Make sure the vma is not shared, that the dst range is
|
|
|
|
|
* both valid and fully within a single existing vma.
|
|
|
|
|
*/
|
2017-02-24 22:58:28 +00:00
|
|
|
err = -ENOENT;
|
2019-12-01 01:57:55 +00:00
|
|
|
dst_vma = find_dst_vma(dst_mm, dst_start, len);
|
2017-02-22 23:43:34 +00:00
|
|
|
if (!dst_vma)
|
|
|
|
|
goto out_unlock;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
2017-02-24 22:58:28 +00:00
|
|
|
err = -EINVAL;
|
|
|
|
|
/*
|
|
|
|
|
* shmem_zero_setup is invoked in mmap for MAP_ANONYMOUS|MAP_SHARED but
|
|
|
|
|
* it will overwrite vm_ops, so vma_is_anonymous must return false.
|
|
|
|
|
*/
|
|
|
|
|
if (WARN_ON_ONCE(vma_is_anonymous(dst_vma) &&
|
|
|
|
|
dst_vma->vm_flags & VM_SHARED))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
2020-04-07 03:05:41 +00:00
|
|
|
/*
|
|
|
|
|
* validate 'mode' now that we know the dst_vma: don't allow
|
|
|
|
|
* a wrprotect copy if the userfaultfd didn't register as WP.
|
|
|
|
|
*/
|
|
|
|
|
wp_copy = mode & UFFDIO_COPY_MODE_WP;
|
|
|
|
|
if (wp_copy && !(dst_vma->vm_flags & VM_UFFD_WP))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
2017-02-22 23:42:55 +00:00
|
|
|
/*
|
|
|
|
|
* If this is a HUGETLB vma, pass off to appropriate routine
|
|
|
|
|
*/
|
|
|
|
|
if (is_vm_hugetlb_page(dst_vma))
|
|
|
|
|
return __mcopy_atomic_hugetlb(dst_mm, dst_vma, dst_start,
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
src_start, len, mcopy_mode);
|
2017-02-22 23:42:55 +00:00
|
|
|
|
2017-02-22 23:43:34 +00:00
|
|
|
if (!vma_is_anonymous(dst_vma) && !vma_is_shmem(dst_vma))
|
2015-09-04 22:47:08 +00:00
|
|
|
goto out_unlock;
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
if (!vma_is_shmem(dst_vma) && mcopy_mode == MCOPY_ATOMIC_CONTINUE)
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
goto out_unlock;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Ensure the dst_vma has a anon_vma or this page
|
|
|
|
|
* would get a NULL anon_vma when moved in the
|
|
|
|
|
* dst_vma.
|
|
|
|
|
*/
|
|
|
|
|
err = -ENOMEM;
|
2018-11-30 22:09:28 +00:00
|
|
|
if (!(dst_vma->vm_flags & VM_SHARED) &&
|
|
|
|
|
unlikely(anon_vma_prepare(dst_vma)))
|
2015-09-04 22:47:08 +00:00
|
|
|
goto out_unlock;
|
2015-09-04 22:47:04 +00:00
|
|
|
|
2015-09-04 22:47:08 +00:00
|
|
|
while (src_addr < src_start + len) {
|
2015-09-04 22:47:04 +00:00
|
|
|
pmd_t dst_pmdval;
|
2015-09-04 22:47:08 +00:00
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
BUG_ON(dst_addr >= dst_start + len);
|
2015-09-04 22:47:08 +00:00
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
dst_pmd = mm_alloc_pmd(dst_mm, dst_addr);
|
|
|
|
|
if (unlikely(!dst_pmd)) {
|
|
|
|
|
err = -ENOMEM;
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
dst_pmdval = pmd_read_atomic(dst_pmd);
|
|
|
|
|
/*
|
|
|
|
|
* If the dst_pmd is mapped as THP don't
|
|
|
|
|
* override it and just be strict.
|
|
|
|
|
*/
|
|
|
|
|
if (unlikely(pmd_trans_huge(dst_pmdval))) {
|
|
|
|
|
err = -EEXIST;
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
if (unlikely(pmd_none(dst_pmdval)) &&
|
mm: treewide: remove unused address argument from pte_alloc functions
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-01-03 23:28:34 +00:00
|
|
|
unlikely(__pte_alloc(dst_mm, dst_pmd))) {
|
2015-09-04 22:47:04 +00:00
|
|
|
err = -ENOMEM;
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
/* If an huge pmd materialized from under us fail */
|
|
|
|
|
if (unlikely(pmd_trans_huge(*dst_pmd))) {
|
|
|
|
|
err = -EFAULT;
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
BUG_ON(pmd_none(*dst_pmd));
|
|
|
|
|
BUG_ON(pmd_trans_huge(*dst_pmd));
|
|
|
|
|
|
2017-09-06 23:23:06 +00:00
|
|
|
err = mfill_atomic_pte(dst_mm, dst_pmd, dst_vma, dst_addr,
|
userfaultfd/shmem: support UFFDIO_CONTINUE for shmem
With this change, userspace can resolve a minor fault within a
shmem-backed area with a UFFDIO_CONTINUE ioctl. The semantics for this
match those for hugetlbfs - we look up the existing page in the page
cache, and install a PTE for it.
This commit introduces a new helper: mfill_atomic_install_pte.
Why handle UFFDIO_CONTINUE for shmem in mm/userfaultfd.c, instead of in
shmem.c? The existing userfault implementation only relies on shmem.c for
VM_SHARED VMAs. However, minor fault handling / CONTINUE work just fine
for !VM_SHARED VMAs as well. We'd prefer to handle CONTINUE for shmem in
one place, regardless of shared/private (to reduce code duplication).
Why add a new mfill_atomic_install_pte helper? A problem we have with
continue is that shmem_mfill_atomic_pte() and mcopy_atomic_pte() are
*close* to what we want, but not exactly. We do want to setup the PTEs in
a CONTINUE operation, but we don't want to e.g. allocate a new page,
charge it (e.g. to the shmem inode), manipulate various flags, etc. Also
we have the problem stated above: shmem_mfill_atomic_pte() and
mcopy_atomic_pte() both handle one-half of the problem (shared / private)
continue cares about. So, introduce mcontinue_atomic_pte(), to handle all
of the shmem continue cases. Introduce the helper so it doesn't duplicate
code with mcopy_atomic_pte().
In a future commit, shmem_mfill_atomic_pte() will also be modified to use
this new helper. However, since this is a bigger refactor, it seems most
clear to do it as a separate change.
Link: https://lkml.kernel.org/r/20210503180737.2487560-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Brian Geffon <bgeffon@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Wang Qing <wangqing@vivo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-07-01 01:49:24 +00:00
|
|
|
src_addr, &page, mcopy_mode, wp_copy);
|
2015-09-04 22:47:04 +00:00
|
|
|
cond_resched();
|
|
|
|
|
|
2018-11-30 22:09:25 +00:00
|
|
|
if (unlikely(err == -ENOENT)) {
|
2015-09-04 22:47:08 +00:00
|
|
|
void *page_kaddr;
|
|
|
|
|
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2015-09-04 22:47:08 +00:00
|
|
|
BUG_ON(!page);
|
|
|
|
|
|
|
|
|
|
page_kaddr = kmap(page);
|
|
|
|
|
err = copy_from_user(page_kaddr,
|
|
|
|
|
(const void __user *) src_addr,
|
|
|
|
|
PAGE_SIZE);
|
|
|
|
|
kunmap(page);
|
|
|
|
|
if (unlikely(err)) {
|
|
|
|
|
err = -EFAULT;
|
|
|
|
|
goto out;
|
|
|
|
|
}
|
2022-03-22 21:42:08 +00:00
|
|
|
flush_dcache_page(page);
|
2015-09-04 22:47:08 +00:00
|
|
|
goto retry;
|
|
|
|
|
} else
|
|
|
|
|
BUG_ON(page);
|
|
|
|
|
|
2015-09-04 22:47:04 +00:00
|
|
|
if (!err) {
|
|
|
|
|
dst_addr += PAGE_SIZE;
|
|
|
|
|
src_addr += PAGE_SIZE;
|
|
|
|
|
copied += PAGE_SIZE;
|
|
|
|
|
|
|
|
|
|
if (fatal_signal_pending(current))
|
|
|
|
|
err = -EINTR;
|
|
|
|
|
}
|
|
|
|
|
if (err)
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
2015-09-04 22:47:08 +00:00
|
|
|
out_unlock:
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2015-09-04 22:47:08 +00:00
|
|
|
out:
|
|
|
|
|
if (page)
|
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-04-01 12:29:47 +00:00
|
|
|
put_page(page);
|
2015-09-04 22:47:04 +00:00
|
|
|
BUG_ON(copied < 0);
|
|
|
|
|
BUG_ON(err > 0);
|
|
|
|
|
BUG_ON(!copied && !err);
|
|
|
|
|
return copied ? copied : err;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
ssize_t mcopy_atomic(struct mm_struct *dst_mm, unsigned long dst_start,
|
userfaultfd: prevent non-cooperative events vs mcopy_atomic races
If a process monitored with userfaultfd changes it's memory mappings or
forks() at the same time as uffd monitor fills the process memory with
UFFDIO_COPY, the actual creation of page table entries and copying of
the data in mcopy_atomic may happen either before of after the memory
mapping modifications and there is no way for the uffd monitor to
maintain consistent view of the process memory layout.
For instance, let's consider fork() running in parallel with
userfaultfd_copy():
process | uffd monitor
---------------------------------+------------------------------
fork() | userfaultfd_copy()
... | ...
dup_mmap() | down_read(mmap_sem)
down_write(mmap_sem) | /* create PTEs, copy data */
dup_uffd() | up_read(mmap_sem)
copy_page_range() |
up_write(mmap_sem) |
dup_uffd_complete() |
/* notify monitor */ |
If the userfaultfd_copy() takes the mmap_sem first, the new page(s) will
be present by the time copy_page_range() is called and they will appear
in the child's memory mappings. However, if the fork() is the first to
take the mmap_sem, the new pages won't be mapped in the child's address
space.
If the pages are not present and child tries to access them, the monitor
will get page fault notification and everything is fine. However, if
the pages *are present*, the child can access them without uffd
noticing. And if we copy them into child it'll see the wrong data.
Since we are talking about background copy, we'd need to decide whether
the pages should be copied or not regardless #PF notifications.
Since userfaultfd monitor has no way to determine what was the order,
let's disallow userfaultfd_copy in parallel with the non-cooperative
events. In such case we return -EAGAIN and the uffd monitor can
understand that userfaultfd_copy() clashed with a non-cooperative event
and take an appropriate action.
Link: http://lkml.kernel.org/r/1527061324-19949-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Pavel Emelyanov <xemul@virtuozzo.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrei Vagin <avagin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-08 00:09:25 +00:00
|
|
|
unsigned long src_start, unsigned long len,
|
2021-09-02 21:58:56 +00:00
|
|
|
atomic_t *mmap_changing, __u64 mode)
|
2015-09-04 22:47:04 +00:00
|
|
|
{
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
return __mcopy_atomic(dst_mm, dst_start, src_start, len,
|
|
|
|
|
MCOPY_ATOMIC_NORMAL, mmap_changing, mode);
|
2015-09-04 22:47:04 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
ssize_t mfill_zeropage(struct mm_struct *dst_mm, unsigned long start,
|
2021-09-02 21:58:56 +00:00
|
|
|
unsigned long len, atomic_t *mmap_changing)
|
2015-09-04 22:47:04 +00:00
|
|
|
{
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
return __mcopy_atomic(dst_mm, start, 0, len, MCOPY_ATOMIC_ZEROPAGE,
|
|
|
|
|
mmap_changing, 0);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
ssize_t mcopy_continue(struct mm_struct *dst_mm, unsigned long start,
|
2021-09-02 21:58:56 +00:00
|
|
|
unsigned long len, atomic_t *mmap_changing)
|
userfaultfd: add UFFDIO_CONTINUE ioctl
This ioctl is how userspace ought to resolve "minor" userfaults. The
idea is, userspace is notified that a minor fault has occurred. It
might change the contents of the page using its second non-UFFD mapping,
or not. Then, it calls UFFDIO_CONTINUE to tell the kernel "I have
ensured the page contents are correct, carry on setting up the mapping".
Note that it doesn't make much sense to use UFFDIO_{COPY,ZEROPAGE} for
MINOR registered VMAs. ZEROPAGE maps the VMA to the zero page; but in
the minor fault case, we already have some pre-existing underlying page.
Likewise, UFFDIO_COPY isn't useful if we have a second non-UFFD mapping.
We'd just use memcpy() or similar instead.
It turns out hugetlb_mcopy_atomic_pte() already does very close to what
we want, if an existing page is provided via `struct page **pagep`. We
already special-case the behavior a bit for the UFFDIO_ZEROPAGE case, so
just extend that design: add an enum for the three modes of operation,
and make the small adjustments needed for the MCOPY_ATOMIC_CONTINUE
case. (Basically, look up the existing page, and avoid adding the
existing page to the page cache or calling set_page_huge_active() on
it.)
Link: https://lkml.kernel.org/r/20210301222728.176417-5-axelrasmussen@google.com
Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Adam Ruprecht <ruprecht@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chinwen Chang <chinwen.chang@mediatek.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Lokesh Gidra <lokeshgidra@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Michal Koutn" <mkoutny@suse.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Mina Almasry <almasrymina@google.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Oliver Upton <oupton@google.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Shawn Anastasio <shawn@anastas.io>
Cc: Steven Price <steven.price@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-05-05 01:35:49 +00:00
|
|
|
{
|
|
|
|
|
return __mcopy_atomic(dst_mm, start, 0, len, MCOPY_ATOMIC_CONTINUE,
|
|
|
|
|
mmap_changing, 0);
|
2015-09-04 22:47:04 +00:00
|
|
|
}
|
2020-04-07 03:06:09 +00:00
|
|
|
|
|
|
|
|
int mwriteprotect_range(struct mm_struct *dst_mm, unsigned long start,
|
2021-09-02 21:58:56 +00:00
|
|
|
unsigned long len, bool enable_wp,
|
|
|
|
|
atomic_t *mmap_changing)
|
2020-04-07 03:06:09 +00:00
|
|
|
{
|
|
|
|
|
struct vm_area_struct *dst_vma;
|
mm/mprotect: use mmu_gather
Patch series "mm/mprotect: avoid unnecessary TLB flushes", v6.
This patchset is intended to remove unnecessary TLB flushes during
mprotect() syscalls. Once this patch-set make it through, similar and
further optimizations for MADV_COLD and userfaultfd would be possible.
Basically, there are 3 optimizations in this patch-set:
1. Use TLB batching infrastructure to batch flushes across VMAs and do
better/fewer flushes. This would also be handy for later userfaultfd
enhancements.
2. Avoid unnecessary TLB flushes. This optimization is the one that
provides most of the performance benefits. Unlike previous versions,
we now only avoid flushes that would not result in spurious
page-faults.
3. Avoiding TLB flushes on change_huge_pmd() that are only needed to
prevent the A/D bits from changing.
Andrew asked for some benchmark numbers. I do not have an easy
determinate macrobenchmark in which it is easy to show benefit. I
therefore ran a microbenchmark: a loop that does the following on
anonymous memory, just as a sanity check to see that time is saved by
avoiding TLB flushes. The loop goes:
mprotect(p, PAGE_SIZE, PROT_READ)
mprotect(p, PAGE_SIZE, PROT_READ|PROT_WRITE)
*p = 0; // make the page writable
The test was run in KVM guest with 1 or 2 threads (the second thread was
busy-looping). I measured the time (cycles) of each operation:
1 thread 2 threads
mmots +patch mmots +patch
PROT_READ 3494 2725 (-22%) 8630 7788 (-10%)
PROT_READ|WRITE 3952 2724 (-31%) 9075 2865 (-68%)
[ mmots = v5.17-rc6-mmots-2022-03-06-20-38 ]
The exact numbers are really meaningless, but the benefit is clear. There
are 2 interesting results though.
(1) PROT_READ is cheaper, while one can expect it not to be affected.
This is presumably due to TLB miss that is saved
(2) Without memory access (*p = 0), the speedup of the patch is even
greater. In that scenario mprotect(PROT_READ) also avoids the TLB flush.
As a result both operations on the patched kernel take roughly ~1500
cycles (with either 1 or 2 threads), whereas on mmotm their cost is as
high as presented in the table.
This patch (of 3):
change_pXX_range() currently does not use mmu_gather, but instead
implements its own deferred TLB flushes scheme. This both complicates the
code, as developers need to be aware of different invalidation schemes,
and prevents opportunities to avoid TLB flushes or perform them in finer
granularity.
The use of mmu_gather for modified PTEs has benefits in various scenarios
even if pages are not released. For instance, if only a single page needs
to be flushed out of a range of many pages, only that page would be
flushed. If a THP page is flushed, on x86 a single TLB invlpg instruction
can be used instead of 512 instructions (or a full TLB flush, which would
Linux would actually use by default). mprotect() over multiple VMAs
requires a single flush.
Use mmu_gather in change_pXX_range(). As the pages are not released, only
record the flushed range using tlb_flush_pXX_range().
Handle THP similarly and get rid of flush_cache_range() which becomes
redundant since tlb_start_vma() calls it when needed.
Link: https://lkml.kernel.org/r/20220401180821.1986781-1-namit@vmware.com
Link: https://lkml.kernel.org/r/20220401180821.1986781-2-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:50 +00:00
|
|
|
struct mmu_gather tlb;
|
2020-04-07 03:06:09 +00:00
|
|
|
pgprot_t newprot;
|
|
|
|
|
int err;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Sanitize the command parameters:
|
|
|
|
|
*/
|
|
|
|
|
BUG_ON(start & ~PAGE_MASK);
|
|
|
|
|
BUG_ON(len & ~PAGE_MASK);
|
|
|
|
|
|
|
|
|
|
/* Does the address range wrap, or is the span zero-sized? */
|
|
|
|
|
BUG_ON(start + len <= start);
|
|
|
|
|
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_lock(dst_mm);
|
2020-04-07 03:06:09 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* If memory mappings are changing because of non-cooperative
|
|
|
|
|
* operation (e.g. mremap) running in parallel, bail out and
|
|
|
|
|
* request the user to retry later
|
|
|
|
|
*/
|
|
|
|
|
err = -EAGAIN;
|
2021-09-02 21:58:56 +00:00
|
|
|
if (mmap_changing && atomic_read(mmap_changing))
|
2020-04-07 03:06:09 +00:00
|
|
|
goto out_unlock;
|
|
|
|
|
|
|
|
|
|
err = -ENOENT;
|
|
|
|
|
dst_vma = find_dst_vma(dst_mm, start, len);
|
|
|
|
|
/*
|
|
|
|
|
* Make sure the vma is not shared, that the dst range is
|
|
|
|
|
* both valid and fully within a single existing vma.
|
|
|
|
|
*/
|
|
|
|
|
if (!dst_vma || (dst_vma->vm_flags & VM_SHARED))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
if (!userfaultfd_wp(dst_vma))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
if (!vma_is_anonymous(dst_vma))
|
|
|
|
|
goto out_unlock;
|
|
|
|
|
|
|
|
|
|
if (enable_wp)
|
|
|
|
|
newprot = vm_get_page_prot(dst_vma->vm_flags & ~(VM_WRITE));
|
|
|
|
|
else
|
|
|
|
|
newprot = vm_get_page_prot(dst_vma->vm_flags);
|
|
|
|
|
|
mm/mprotect: use mmu_gather
Patch series "mm/mprotect: avoid unnecessary TLB flushes", v6.
This patchset is intended to remove unnecessary TLB flushes during
mprotect() syscalls. Once this patch-set make it through, similar and
further optimizations for MADV_COLD and userfaultfd would be possible.
Basically, there are 3 optimizations in this patch-set:
1. Use TLB batching infrastructure to batch flushes across VMAs and do
better/fewer flushes. This would also be handy for later userfaultfd
enhancements.
2. Avoid unnecessary TLB flushes. This optimization is the one that
provides most of the performance benefits. Unlike previous versions,
we now only avoid flushes that would not result in spurious
page-faults.
3. Avoiding TLB flushes on change_huge_pmd() that are only needed to
prevent the A/D bits from changing.
Andrew asked for some benchmark numbers. I do not have an easy
determinate macrobenchmark in which it is easy to show benefit. I
therefore ran a microbenchmark: a loop that does the following on
anonymous memory, just as a sanity check to see that time is saved by
avoiding TLB flushes. The loop goes:
mprotect(p, PAGE_SIZE, PROT_READ)
mprotect(p, PAGE_SIZE, PROT_READ|PROT_WRITE)
*p = 0; // make the page writable
The test was run in KVM guest with 1 or 2 threads (the second thread was
busy-looping). I measured the time (cycles) of each operation:
1 thread 2 threads
mmots +patch mmots +patch
PROT_READ 3494 2725 (-22%) 8630 7788 (-10%)
PROT_READ|WRITE 3952 2724 (-31%) 9075 2865 (-68%)
[ mmots = v5.17-rc6-mmots-2022-03-06-20-38 ]
The exact numbers are really meaningless, but the benefit is clear. There
are 2 interesting results though.
(1) PROT_READ is cheaper, while one can expect it not to be affected.
This is presumably due to TLB miss that is saved
(2) Without memory access (*p = 0), the speedup of the patch is even
greater. In that scenario mprotect(PROT_READ) also avoids the TLB flush.
As a result both operations on the patched kernel take roughly ~1500
cycles (with either 1 or 2 threads), whereas on mmotm their cost is as
high as presented in the table.
This patch (of 3):
change_pXX_range() currently does not use mmu_gather, but instead
implements its own deferred TLB flushes scheme. This both complicates the
code, as developers need to be aware of different invalidation schemes,
and prevents opportunities to avoid TLB flushes or perform them in finer
granularity.
The use of mmu_gather for modified PTEs has benefits in various scenarios
even if pages are not released. For instance, if only a single page needs
to be flushed out of a range of many pages, only that page would be
flushed. If a THP page is flushed, on x86 a single TLB invlpg instruction
can be used instead of 512 instructions (or a full TLB flush, which would
Linux would actually use by default). mprotect() over multiple VMAs
requires a single flush.
Use mmu_gather in change_pXX_range(). As the pages are not released, only
record the flushed range using tlb_flush_pXX_range().
Handle THP similarly and get rid of flush_cache_range() which becomes
redundant since tlb_start_vma() calls it when needed.
Link: https://lkml.kernel.org/r/20220401180821.1986781-1-namit@vmware.com
Link: https://lkml.kernel.org/r/20220401180821.1986781-2-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:50 +00:00
|
|
|
tlb_gather_mmu(&tlb, dst_mm);
|
|
|
|
|
change_protection(&tlb, dst_vma, start, start + len, newprot,
|
2020-04-07 03:06:09 +00:00
|
|
|
enable_wp ? MM_CP_UFFD_WP : MM_CP_UFFD_WP_RESOLVE);
|
mm/mprotect: use mmu_gather
Patch series "mm/mprotect: avoid unnecessary TLB flushes", v6.
This patchset is intended to remove unnecessary TLB flushes during
mprotect() syscalls. Once this patch-set make it through, similar and
further optimizations for MADV_COLD and userfaultfd would be possible.
Basically, there are 3 optimizations in this patch-set:
1. Use TLB batching infrastructure to batch flushes across VMAs and do
better/fewer flushes. This would also be handy for later userfaultfd
enhancements.
2. Avoid unnecessary TLB flushes. This optimization is the one that
provides most of the performance benefits. Unlike previous versions,
we now only avoid flushes that would not result in spurious
page-faults.
3. Avoiding TLB flushes on change_huge_pmd() that are only needed to
prevent the A/D bits from changing.
Andrew asked for some benchmark numbers. I do not have an easy
determinate macrobenchmark in which it is easy to show benefit. I
therefore ran a microbenchmark: a loop that does the following on
anonymous memory, just as a sanity check to see that time is saved by
avoiding TLB flushes. The loop goes:
mprotect(p, PAGE_SIZE, PROT_READ)
mprotect(p, PAGE_SIZE, PROT_READ|PROT_WRITE)
*p = 0; // make the page writable
The test was run in KVM guest with 1 or 2 threads (the second thread was
busy-looping). I measured the time (cycles) of each operation:
1 thread 2 threads
mmots +patch mmots +patch
PROT_READ 3494 2725 (-22%) 8630 7788 (-10%)
PROT_READ|WRITE 3952 2724 (-31%) 9075 2865 (-68%)
[ mmots = v5.17-rc6-mmots-2022-03-06-20-38 ]
The exact numbers are really meaningless, but the benefit is clear. There
are 2 interesting results though.
(1) PROT_READ is cheaper, while one can expect it not to be affected.
This is presumably due to TLB miss that is saved
(2) Without memory access (*p = 0), the speedup of the patch is even
greater. In that scenario mprotect(PROT_READ) also avoids the TLB flush.
As a result both operations on the patched kernel take roughly ~1500
cycles (with either 1 or 2 threads), whereas on mmotm their cost is as
high as presented in the table.
This patch (of 3):
change_pXX_range() currently does not use mmu_gather, but instead
implements its own deferred TLB flushes scheme. This both complicates the
code, as developers need to be aware of different invalidation schemes,
and prevents opportunities to avoid TLB flushes or perform them in finer
granularity.
The use of mmu_gather for modified PTEs has benefits in various scenarios
even if pages are not released. For instance, if only a single page needs
to be flushed out of a range of many pages, only that page would be
flushed. If a THP page is flushed, on x86 a single TLB invlpg instruction
can be used instead of 512 instructions (or a full TLB flush, which would
Linux would actually use by default). mprotect() over multiple VMAs
requires a single flush.
Use mmu_gather in change_pXX_range(). As the pages are not released, only
record the flushed range using tlb_flush_pXX_range().
Handle THP similarly and get rid of flush_cache_range() which becomes
redundant since tlb_start_vma() calls it when needed.
Link: https://lkml.kernel.org/r/20220401180821.1986781-1-namit@vmware.com
Link: https://lkml.kernel.org/r/20220401180821.1986781-2-namit@vmware.com
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Nick Piggin <npiggin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2022-05-10 01:20:50 +00:00
|
|
|
tlb_finish_mmu(&tlb);
|
2020-04-07 03:06:09 +00:00
|
|
|
|
|
|
|
|
err = 0;
|
|
|
|
|
out_unlock:
|
2020-06-09 04:33:25 +00:00
|
|
|
mmap_read_unlock(dst_mm);
|
2020-04-07 03:06:09 +00:00
|
|
|
return err;
|
|
|
|
|
}
|
