Minki/linux
1
0
Fork 1
mirror of https://github.com/torvalds/linux.git synced 2024-12-17 00:21:32 +00:00
Code Issues Packages Projects Releases Wiki Activity
523cb50b26
linux/drivers/net/bnx2x_init_values.h

2587 lines
110 KiB
C
Raw Normal View History

add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
#ifndef __BNX2X_INIT_VALUES_H__
#define __BNX2X_INIT_VALUES_H__
/* This array contains the list of operations needed to initialize the chip.
*
* For each block in the chip there are three init stages:
* common - HW used by both ports,
* port1 and port2 - initialization for a specific Ethernet port.
* When a port is opened or closed, the management CPU tells the driver
* whether to init/disable common HW in addition to the port HW.
* This way the first port going up will first initializes the common HW,
* and the last port going down also resets the common HW
*
* For each init stage/block there is a list of actions needed in a format:
* {operation, register, data}
* where:
* OP_WR - write a value to the chip.
* OP_RD - read a register (usually a clear on read register).
* OP_SW - string write, write a section of consecutive addresses to the chip.
* OP_SI - copy a string using indirect writes.
* OP_ZR - clear a range of memory.
* OP_ZP - unzip and copy using DMAE.
* OP_WB - string copy using DMAE.
*
* The #defines mark the stages.
*
*/
static const struct raw_op init_ops[] = {
#define PRS_COMMON_START 0
{OP_WR, PRS_REG_INC_VALUE, 0xf},
{OP_WR, PRS_REG_EVENT_ID_1, 0x45},
{OP_WR, PRS_REG_EVENT_ID_2, 0x84},
{OP_WR, PRS_REG_EVENT_ID_3, 0x6},
{OP_WR, PRS_REG_NO_MATCH_EVENT_ID, 0x4},
{OP_WR, PRS_REG_CM_HDR_TYPE_0, 0x0},
{OP_WR, PRS_REG_CM_HDR_TYPE_1, 0x12170000},
{OP_WR, PRS_REG_CM_HDR_TYPE_2, 0x22170000},
{OP_WR, PRS_REG_CM_HDR_TYPE_3, 0x32170000},
{OP_ZR, PRS_REG_CM_HDR_TYPE_4, 0x5},
{OP_WR, PRS_REG_CM_HDR_LOOPBACK_TYPE_1, 0x12150000},
{OP_WR, PRS_REG_CM_HDR_LOOPBACK_TYPE_2, 0x22150000},
{OP_WR, PRS_REG_CM_HDR_LOOPBACK_TYPE_3, 0x32150000},
{OP_ZR, PRS_REG_CM_HDR_LOOPBACK_TYPE_4, 0x4},
{OP_WR, PRS_REG_CM_NO_MATCH_HDR, 0x2100000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_0, 0x100000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_1, 0x10100000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_2, 0x20100000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_3, 0x30100000},
{OP_ZR, PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_4, 0x4},
{OP_WR, PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_0, 0x100000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_1, 0x12140000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_2, 0x22140000},
{OP_WR, PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_3, 0x32140000},
{OP_ZR, PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_4, 0x4},
{OP_RD, PRS_REG_NUM_OF_PACKETS, 0x0},
{OP_RD, PRS_REG_NUM_OF_CFC_FLUSH_MESSAGES, 0x0},
{OP_RD, PRS_REG_NUM_OF_TRANSPARENT_FLUSH_MESSAGES, 0x0},
{OP_RD, PRS_REG_NUM_OF_DEAD_CYCLES, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, PRS_REG_FCOE_TYPE, 0x8906},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_0, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_1, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_2, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_3, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_4, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_5, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_6, 0xff},
{OP_WR, PRS_REG_FLUSH_REGIONS_TYPE_7, 0xff},
{OP_WR, PRS_REG_PURE_REGIONS, 0x3e},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_0, 0x0},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_1, 0x3f},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_2, 0x3f},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_3, 0x3f},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_4, 0x0},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_5, 0x3f},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_6, 0x3f},
{OP_WR, PRS_REG_PACKET_REGIONS_TYPE_7, 0x3f},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define PRS_COMMON_END 47
#define SRCH_COMMON_START 47
{OP_WR_E1H, SRC_REG_E1HMF_ENABLE, 0x1},
#define SRCH_COMMON_END 48
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
#define TSDM_COMMON_START 48
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, TSDM_REG_CFC_RSP_START_ADDR, 0x411},
{OP_WR_E1H, TSDM_REG_CFC_RSP_START_ADDR, 0x211},
{OP_WR_E1, TSDM_REG_CMP_COUNTER_START_ADDR, 0x400},
{OP_WR_E1H, TSDM_REG_CMP_COUNTER_START_ADDR, 0x200},
{OP_WR_E1, TSDM_REG_Q_COUNTER_START_ADDR, 0x404},
{OP_WR_E1H, TSDM_REG_Q_COUNTER_START_ADDR, 0x204},
{OP_WR_E1, TSDM_REG_PCK_END_MSG_START_ADDR, 0x419},
{OP_WR_E1H, TSDM_REG_PCK_END_MSG_START_ADDR, 0x219},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TSDM_REG_CMP_COUNTER_MAX0, 0xffff},
{OP_WR, TSDM_REG_CMP_COUNTER_MAX1, 0xffff},
{OP_WR, TSDM_REG_CMP_COUNTER_MAX2, 0xffff},
{OP_WR, TSDM_REG_CMP_COUNTER_MAX3, 0xffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR, TSDM_REG_AGG_INT_EVENT_0, 0x2},
{OP_WR, TSDM_REG_AGG_INT_EVENT_2, 0x34},
{OP_WR, TSDM_REG_AGG_INT_EVENT_3, 0x35},
{OP_ZR, TSDM_REG_AGG_INT_EVENT_4, 0x7c},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TSDM_REG_ENABLE_IN1, 0x7ffffff},
{OP_WR, TSDM_REG_ENABLE_IN2, 0x3f},
{OP_WR, TSDM_REG_ENABLE_OUT1, 0x7ffffff},
{OP_WR, TSDM_REG_ENABLE_OUT2, 0xf},
{OP_RD, TSDM_REG_NUM_OF_Q0_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q1_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q3_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q4_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q5_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q6_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q7_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q8_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q9_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q10_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_Q11_CMD, 0x0},
{OP_RD, TSDM_REG_NUM_OF_PKT_END_MSG, 0x0},
{OP_RD, TSDM_REG_NUM_OF_PXP_ASYNC_REQ, 0x0},
{OP_RD, TSDM_REG_NUM_OF_ACK_AFTER_PLACE, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, TSDM_REG_INIT_CREDIT_PXP_CTRL, 0x1},
{OP_WR_ASIC, TSDM_REG_TIMER_TICK, 0x3e8},
{OP_WR_EMUL, TSDM_REG_TIMER_TICK, 0x1},
{OP_WR_FPGA, TSDM_REG_TIMER_TICK, 0xa},
#define TSDM_COMMON_END 86
#define TCM_COMMON_START 86
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TCM_REG_XX_MAX_LL_SZ, 0x20},
{OP_WR, TCM_REG_XX_OVFL_EVNT_ID, 0x32},
{OP_WR, TCM_REG_TQM_TCM_HDR_P, 0x2150020},
{OP_WR, TCM_REG_TQM_TCM_HDR_S, 0x2150020},
{OP_WR, TCM_REG_TM_TCM_HDR, 0x30},
{OP_WR, TCM_REG_ERR_TCM_HDR, 0x8100000},
{OP_WR, TCM_REG_ERR_EVNT_ID, 0x33},
{OP_WR, TCM_REG_EXPR_EVNT_ID, 0x30},
{OP_WR, TCM_REG_STOP_EVNT_ID, 0x31},
{OP_WR, TCM_REG_PRS_WEIGHT, 0x4},
{OP_WR, TCM_REG_PBF_WEIGHT, 0x5},
{OP_WR, TCM_REG_CP_WEIGHT, 0x0},
{OP_WR, TCM_REG_TSDM_WEIGHT, 0x4},
{OP_WR, TCM_REG_TCM_TQM_USE_Q, 0x1},
{OP_WR, TCM_REG_GR_ARB_TYPE, 0x1},
{OP_WR, TCM_REG_GR_LD0_PR, 0x1},
{OP_WR, TCM_REG_GR_LD1_PR, 0x2},
{OP_WR, TCM_REG_CFC_INIT_CRD, 0x1},
{OP_WR, TCM_REG_FIC0_INIT_CRD, 0x40},
{OP_WR, TCM_REG_FIC1_INIT_CRD, 0x40},
{OP_WR, TCM_REG_TQM_INIT_CRD, 0x20},
{OP_WR, TCM_REG_XX_INIT_CRD, 0x13},
{OP_WR, TCM_REG_XX_MSG_NUM, 0x20},
{OP_ZR, TCM_REG_XX_TABLE, 0xa},
{OP_SW, TCM_REG_XX_DESCR_TABLE, 0x200000},
{OP_WR, TCM_REG_N_SM_CTX_LD_0, 0x7},
{OP_WR, TCM_REG_N_SM_CTX_LD_1, 0x7},
{OP_WR, TCM_REG_N_SM_CTX_LD_2, 0x8},
{OP_WR, TCM_REG_N_SM_CTX_LD_3, 0x8},
{OP_ZR, TCM_REG_N_SM_CTX_LD_4, 0x4},
{OP_WR, TCM_REG_TCM_REG0_SZ, 0x6},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, TCM_REG_PHYS_QNUM0_0, 0xd},
{OP_WR_E1, TCM_REG_PHYS_QNUM0_1, 0x2d},
{OP_WR_E1, TCM_REG_PHYS_QNUM1_0, 0x7},
{OP_WR_E1, TCM_REG_PHYS_QNUM1_1, 0x27},
{OP_WR_E1, TCM_REG_PHYS_QNUM2_0, 0x7},
{OP_WR_E1, TCM_REG_PHYS_QNUM2_1, 0x27},
{OP_WR_E1, TCM_REG_PHYS_QNUM3_0, 0x7},
{OP_WR_E1, TCM_REG_PHYS_QNUM3_1, 0x27},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TCM_REG_TCM_STORM0_IFEN, 0x1},
{OP_WR, TCM_REG_TCM_STORM1_IFEN, 0x1},
{OP_WR, TCM_REG_TCM_TQM_IFEN, 0x1},
{OP_WR, TCM_REG_STORM_TCM_IFEN, 0x1},
{OP_WR, TCM_REG_TQM_TCM_IFEN, 0x1},
{OP_WR, TCM_REG_TSDM_IFEN, 0x1},
{OP_WR, TCM_REG_TM_TCM_IFEN, 0x1},
{OP_WR, TCM_REG_PRS_IFEN, 0x1},
{OP_WR, TCM_REG_PBF_IFEN, 0x1},
{OP_WR, TCM_REG_USEM_IFEN, 0x1},
{OP_WR, TCM_REG_CSEM_IFEN, 0x1},
{OP_WR, TCM_REG_CDU_AG_WR_IFEN, 0x1},
{OP_WR, TCM_REG_CDU_AG_RD_IFEN, 0x1},
{OP_WR, TCM_REG_CDU_SM_WR_IFEN, 0x1},
{OP_WR, TCM_REG_CDU_SM_RD_IFEN, 0x1},
{OP_WR, TCM_REG_TCM_CFC_IFEN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define TCM_COMMON_END 141
#define TCM_FUNC0_START 141
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_0, 0xd},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_0, 0x7},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_0, 0x7},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_0, 0x7},
#define TCM_FUNC0_END 145
#define TCM_FUNC1_START 145
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_1, 0x2d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_1, 0x27},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_1, 0x27},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_1, 0x27},
#define TCM_FUNC1_END 149
#define TCM_FUNC2_START 149
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_0, 0x1d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_0, 0x17},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_0, 0x17},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_0, 0x17},
#define TCM_FUNC2_END 153
#define TCM_FUNC3_START 153
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_1, 0x3d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_1, 0x37},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_1, 0x37},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_1, 0x37},
#define TCM_FUNC3_END 157
#define TCM_FUNC4_START 157
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_0, 0x4d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_0, 0x47},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_0, 0x47},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_0, 0x47},
#define TCM_FUNC4_END 161
#define TCM_FUNC5_START 161
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_1, 0x6d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_1, 0x67},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_1, 0x67},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_1, 0x67},
#define TCM_FUNC5_END 165
#define TCM_FUNC6_START 165
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_0, 0x5d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_0, 0x57},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_0, 0x57},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_0, 0x57},
#define TCM_FUNC6_END 169
#define TCM_FUNC7_START 169
{OP_WR_E1H, TCM_REG_PHYS_QNUM0_1, 0x7d},
{OP_WR_E1H, TCM_REG_PHYS_QNUM1_1, 0x77},
{OP_WR_E1H, TCM_REG_PHYS_QNUM2_1, 0x77},
{OP_WR_E1H, TCM_REG_PHYS_QNUM3_1, 0x77},
#define TCM_FUNC7_END 173
#define BRB1_COMMON_START 173
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_SW, BRB1_REG_LL_RAM, 0x2000020},
{OP_WR, BRB1_REG_SOFT_RESET, 0x1},
{OP_RD, BRB1_REG_NUM_OF_FULL_CYCLES_4, 0x0},
{OP_SW, BRB1_REG_FREE_LIST_PRS_CRDT, 0x30220},
{OP_WR, BRB1_REG_SOFT_RESET, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define BRB1_COMMON_END 178
#define BRB1_PORT0_START 178
{OP_WR_E1, BRB1_REG_PAUSE_LOW_THRESHOLD_0, 0xb8},
{OP_WR_E1, BRB1_REG_PAUSE_HIGH_THRESHOLD_0, 0x114},
{OP_RD, BRB1_REG_NUM_OF_PAUSE_CYCLES_0, 0x0},
{OP_RD, BRB1_REG_NUM_OF_FULL_CYCLES_0, 0x0},
#define BRB1_PORT0_END 182
#define BRB1_PORT1_START 182
{OP_WR_E1, BRB1_REG_PAUSE_LOW_THRESHOLD_1, 0xb8},
{OP_WR_E1, BRB1_REG_PAUSE_HIGH_THRESHOLD_1, 0x114},
{OP_RD, BRB1_REG_NUM_OF_PAUSE_CYCLES_1, 0x0},
{OP_RD, BRB1_REG_NUM_OF_FULL_CYCLES_1, 0x0},
#define BRB1_PORT1_END 186
#define TSEM_COMMON_START 186
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_RD, TSEM_REG_MSG_NUM_FIC0, 0x0},
{OP_RD, TSEM_REG_MSG_NUM_FIC1, 0x0},
{OP_RD, TSEM_REG_MSG_NUM_FOC0, 0x0},
{OP_RD, TSEM_REG_MSG_NUM_FOC1, 0x0},
{OP_RD, TSEM_REG_MSG_NUM_FOC2, 0x0},
{OP_RD, TSEM_REG_MSG_NUM_FOC3, 0x0},
{OP_WR, TSEM_REG_ARB_ELEMENT0, 0x1},
{OP_WR, TSEM_REG_ARB_ELEMENT1, 0x2},
{OP_WR, TSEM_REG_ARB_ELEMENT2, 0x3},
{OP_WR, TSEM_REG_ARB_ELEMENT3, 0x0},
{OP_WR, TSEM_REG_ARB_ELEMENT4, 0x4},
{OP_WR, TSEM_REG_ARB_CYCLE_SIZE, 0x1},
{OP_WR, TSEM_REG_TS_0_AS, 0x0},
{OP_WR, TSEM_REG_TS_1_AS, 0x1},
{OP_WR, TSEM_REG_TS_2_AS, 0x4},
{OP_WR, TSEM_REG_TS_3_AS, 0x0},
{OP_WR, TSEM_REG_TS_4_AS, 0x1},
{OP_WR, TSEM_REG_TS_5_AS, 0x3},
{OP_WR, TSEM_REG_TS_6_AS, 0x0},
{OP_WR, TSEM_REG_TS_7_AS, 0x1},
{OP_WR, TSEM_REG_TS_8_AS, 0x4},
{OP_WR, TSEM_REG_TS_9_AS, 0x0},
{OP_WR, TSEM_REG_TS_10_AS, 0x1},
{OP_WR, TSEM_REG_TS_11_AS, 0x3},
{OP_WR, TSEM_REG_TS_12_AS, 0x0},
{OP_WR, TSEM_REG_TS_13_AS, 0x1},
{OP_WR, TSEM_REG_TS_14_AS, 0x4},
{OP_WR, TSEM_REG_TS_15_AS, 0x0},
{OP_WR, TSEM_REG_TS_16_AS, 0x4},
{OP_WR, TSEM_REG_TS_17_AS, 0x3},
{OP_ZR, TSEM_REG_TS_18_AS, 0x2},
{OP_WR, TSEM_REG_ENABLE_IN, 0x3fff},
{OP_WR, TSEM_REG_ENABLE_OUT, 0x3ff},
{OP_WR, TSEM_REG_FIC0_DISABLE, 0x0},
{OP_WR, TSEM_REG_FIC1_DISABLE, 0x0},
{OP_WR, TSEM_REG_PAS_DISABLE, 0x0},
{OP_WR, TSEM_REG_THREADS_LIST, 0xff},
{OP_ZR, TSEM_REG_PASSIVE_BUFFER, 0x400},
{OP_WR, TSEM_REG_FAST_MEMORY + 0x18bc0, 0x1},
{OP_WR, TSEM_REG_FAST_MEMORY + 0x18000, 0x34},
{OP_WR, TSEM_REG_FAST_MEMORY + 0x18040, 0x18},
{OP_WR, TSEM_REG_FAST_MEMORY + 0x18080, 0xc},
{OP_WR, TSEM_REG_FAST_MEMORY + 0x180c0, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_ASIC, TSEM_REG_FAST_MEMORY + 0x18300, 0x7a120},
{OP_WR_EMUL, TSEM_REG_FAST_MEMORY + 0x18300, 0x138},
{OP_WR_FPGA, TSEM_REG_FAST_MEMORY + 0x18300, 0x1388},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TSEM_REG_FAST_MEMORY + 0x183c0, 0x1f4},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x2000, 0xb2},
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x11480, 0x1},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x23c8, 0xc1},
{OP_WR_EMUL_E1H, TSEM_REG_FAST_MEMORY + 0x11480, 0x0},
{OP_SW_E1, TSEM_REG_FAST_MEMORY + 0x23c8 + 0x304, 0x10223},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x1000, 0x2b3},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1020, 0xc8},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x1000 + 0xacc, 0x10223},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1000, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xa020, 0xc8},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1c18, 0x4},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xa000, 0x2},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x800, 0x2},
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x1ad0, 0x0},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x808, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3b28, 0x6},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x810, 0x4},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5000, 0x2},
{OP_SW_E1, TSEM_REG_FAST_MEMORY + 0x1fb0, 0x40224},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5008, 0x4},
{OP_SW_E1, TSEM_REG_FAST_MEMORY + 0x4cb0, 0x80228},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5018, 0x4},
{OP_ZP_E1, TSEM_REG_INT_TABLE, 0x940000},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5028, 0x4},
{OP_WR_64_E1, TSEM_REG_INT_TABLE + 0x360, 0x140230},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5038, 0x4},
{OP_ZP_E1, TSEM_REG_PRAM, 0x6ab70000},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5048, 0x4},
{OP_WR_64_E1, TSEM_REG_PRAM + 0x117f0, 0x5d020232},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5058, 0x4},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5068, 0x4},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5078, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x4000, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x4008, 0x2},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x6140, 0x200224},
{OP_ZP_E1H, TSEM_REG_INT_TABLE, 0x960000},
{OP_WR_64_E1H, TSEM_REG_INT_TABLE + 0x360, 0x140244},
{OP_ZP_E1H, TSEM_REG_PRAM, 0x6d080000},
{OP_WR_64_E1H, TSEM_REG_PRAM + 0x11c70, 0x5c720246},
#define TSEM_COMMON_END 272
#define TSEM_PORT0_START 272
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x22c8, 0x20},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x2000, 0x16c},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x4000, 0xfc},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xb000, 0x28},
{OP_WR_E1, TSEM_REG_FAST_MEMORY + 0x4b60, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xb140, 0xc},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1400, 0xa},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x32c0, 0x12},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1450, 0x6},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3350, 0xfa},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1500, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x8108, 0x2},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1570, 0x12},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x9c0, 0xbe},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x800, 0x2},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x820, 0xe},
{OP_SW_E1, TSEM_REG_FAST_MEMORY + 0x1fb0, 0x20234},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x2908, 0x2},
#define TSEM_PORT0_END 290
#define TSEM_PORT1_START 290
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x2348, 0x20},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x25b0, 0x16c},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x43f0, 0xfc},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xb0a0, 0x28},
{OP_WR_E1, TSEM_REG_FAST_MEMORY + 0x4b64, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0xb170, 0xc},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1428, 0xa},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3308, 0x12},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1468, 0x6},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3738, 0xfa},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x1538, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x8110, 0x2},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x15b8, 0x12},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0xcb8, 0xbe},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x808, 0x2},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x858, 0xe},
{OP_SW_E1, TSEM_REG_FAST_MEMORY + 0x1fb8, 0x20236},
{OP_ZR_E1, TSEM_REG_FAST_MEMORY + 0x2910, 0x2},
#define TSEM_PORT1_END 308
#define TSEM_FUNC0_START 308
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b60, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3000, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x31c0, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5000, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5080, 0x12},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x4000, 0x2},
#define TSEM_FUNC0_END 314
#define TSEM_FUNC1_START 314
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b64, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3038, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x31e0, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5010, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x50c8, 0x12},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x4008, 0x2},
#define TSEM_FUNC1_END 320
#define TSEM_FUNC2_START 320
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b68, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3070, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3200, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5020, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5110, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4010, 0x20248},
#define TSEM_FUNC2_END 326
#define TSEM_FUNC3_START 326
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b6c, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x30a8, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3220, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5030, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5158, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4018, 0x2024a},
#define TSEM_FUNC3_END 332
#define TSEM_FUNC4_START 332
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b70, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x30e0, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3240, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5040, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x51a0, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4020, 0x2024c},
#define TSEM_FUNC4_END 338
#define TSEM_FUNC5_START 338
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b74, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3118, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3260, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5050, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x51e8, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4028, 0x2024e},
#define TSEM_FUNC5_END 344
#define TSEM_FUNC6_START 344
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b78, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3150, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3280, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5060, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5230, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4030, 0x20250},
#define TSEM_FUNC6_END 350
#define TSEM_FUNC7_START 350
{OP_WR_E1H, TSEM_REG_FAST_MEMORY + 0x2b7c, 0x0},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x3188, 0xe},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x32a0, 0x8},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5070, 0x2},
{OP_ZR_E1H, TSEM_REG_FAST_MEMORY + 0x5278, 0x12},
{OP_SW_E1H, TSEM_REG_FAST_MEMORY + 0x4038, 0x20252},
#define TSEM_FUNC7_END 356
#define MISC_COMMON_START 356
{OP_WR_E1, MISC_REG_GRC_TIMEOUT_EN, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, MISC_REG_PLL_STORM_CTRL_1, 0x71d2911},
{OP_WR, MISC_REG_PLL_STORM_CTRL_2, 0x0},
{OP_WR, MISC_REG_PLL_STORM_CTRL_3, 0x9c0424},
{OP_WR, MISC_REG_PLL_STORM_CTRL_4, 0x0},
{OP_WR, MISC_REG_LCPLL_CTRL_1, 0x209},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, MISC_REG_SPIO, 0xff000000},
#define MISC_COMMON_END 363
#define MISC_FUNC0_START 363
{OP_WR_E1H, MISC_REG_NIG_WOL_P0, 0x0},
#define MISC_FUNC0_END 364
#define MISC_FUNC1_START 364
{OP_WR_E1H, MISC_REG_NIG_WOL_P1, 0x0},
#define MISC_FUNC1_END 365
#define MISC_FUNC2_START 365
{OP_WR_E1H, MISC_REG_NIG_WOL_P0, 0x0},
#define MISC_FUNC2_END 366
#define MISC_FUNC3_START 366
{OP_WR_E1H, MISC_REG_NIG_WOL_P1, 0x0},
#define MISC_FUNC3_END 367
#define MISC_FUNC4_START 367
{OP_WR_E1H, MISC_REG_NIG_WOL_P0, 0x0},
#define MISC_FUNC4_END 368
#define MISC_FUNC5_START 368
{OP_WR_E1H, MISC_REG_NIG_WOL_P1, 0x0},
#define MISC_FUNC5_END 369
#define MISC_FUNC6_START 369
{OP_WR_E1H, MISC_REG_NIG_WOL_P0, 0x0},
#define MISC_FUNC6_END 370
#define MISC_FUNC7_START 370
{OP_WR_E1H, MISC_REG_NIG_WOL_P1, 0x0},
#define MISC_FUNC7_END 371
#define NIG_COMMON_START 371
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_PBF_LB_IN_EN, 0x1},
{OP_WR, NIG_REG_PRS_REQ_IN_EN, 0x1},
{OP_WR, NIG_REG_EGRESS_DEBUG_IN_EN, 0x1},
{OP_WR, NIG_REG_BRB_LB_OUT_EN, 0x1},
{OP_WR, NIG_REG_PRS_EOP_OUT_EN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define NIG_COMMON_END 376
#define NIG_PORT0_START 376
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH0_CM_HEADER, 0x300000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, NIG_REG_LLH0_EVENT_ID, 0x28},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH0_ERROR_MASK, 0x0},
{OP_WR, NIG_REG_LLH0_XCM_MASK, 0x4},
{OP_WR, NIG_REG_LLH0_BRB1_NOT_MCP, 0x1},
{OP_WR, NIG_REG_STATUS_INTERRUPT_PORT0, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, NIG_REG_LLH0_CLS_TYPE, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH0_XCM_INIT_CREDIT, 0x30},
{OP_WR, NIG_REG_BRB0_PAUSE_IN_EN, 0x1},
{OP_WR, NIG_REG_EGRESS_PBF0_IN_EN, 0x1},
{OP_WR, NIG_REG_BRB0_OUT_EN, 0x1},
{OP_WR, NIG_REG_XCM0_OUT_EN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define NIG_PORT0_END 388
#define NIG_PORT1_START 388
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH1_CM_HEADER, 0x300000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, NIG_REG_LLH1_EVENT_ID, 0x28},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH1_ERROR_MASK, 0x0},
{OP_WR, NIG_REG_LLH1_XCM_MASK, 0x4},
{OP_WR, NIG_REG_LLH1_BRB1_NOT_MCP, 0x1},
{OP_WR, NIG_REG_STATUS_INTERRUPT_PORT1, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, NIG_REG_LLH1_CLS_TYPE, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, NIG_REG_LLH1_XCM_INIT_CREDIT, 0x30},
{OP_WR, NIG_REG_BRB1_PAUSE_IN_EN, 0x1},
{OP_WR, NIG_REG_EGRESS_PBF1_IN_EN, 0x1},
{OP_WR, NIG_REG_BRB1_OUT_EN, 0x1},
{OP_WR, NIG_REG_XCM1_OUT_EN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define NIG_PORT1_END 400
#define UPB_COMMON_START 400
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, GRCBASE_UPB + PB_REG_CONTROL, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define UPB_COMMON_END 401
#define CSDM_COMMON_START 401
{OP_WR_E1, CSDM_REG_CFC_RSP_START_ADDR, 0xa11},
{OP_WR_E1H, CSDM_REG_CFC_RSP_START_ADDR, 0x211},
{OP_WR_E1, CSDM_REG_CMP_COUNTER_START_ADDR, 0xa00},
{OP_WR_E1H, CSDM_REG_CMP_COUNTER_START_ADDR, 0x200},
{OP_WR_E1, CSDM_REG_Q_COUNTER_START_ADDR, 0xa04},
{OP_WR_E1H, CSDM_REG_Q_COUNTER_START_ADDR, 0x204},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CSDM_REG_CMP_COUNTER_MAX0, 0xffff},
{OP_WR, CSDM_REG_CMP_COUNTER_MAX1, 0xffff},
{OP_WR, CSDM_REG_CMP_COUNTER_MAX2, 0xffff},
{OP_WR, CSDM_REG_CMP_COUNTER_MAX3, 0xffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, CSDM_REG_AGG_INT_EVENT_0, 0xc6},
{OP_WR, CSDM_REG_AGG_INT_EVENT_1, 0x0},
{OP_WR, CSDM_REG_AGG_INT_EVENT_2, 0x34},
{OP_WR, CSDM_REG_AGG_INT_EVENT_3, 0x35},
{OP_ZR, CSDM_REG_AGG_INT_EVENT_4, 0x1c},
{OP_WR, CSDM_REG_AGG_INT_T_0, 0x1},
{OP_ZR, CSDM_REG_AGG_INT_T_1, 0x5f},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CSDM_REG_ENABLE_IN1, 0x7ffffff},
{OP_WR, CSDM_REG_ENABLE_IN2, 0x3f},
{OP_WR, CSDM_REG_ENABLE_OUT1, 0x7ffffff},
{OP_WR, CSDM_REG_ENABLE_OUT2, 0xf},
{OP_RD, CSDM_REG_NUM_OF_Q0_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q1_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q3_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q4_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q5_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q6_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q7_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q8_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q9_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q10_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_Q11_CMD, 0x0},
{OP_RD, CSDM_REG_NUM_OF_PKT_END_MSG, 0x0},
{OP_RD, CSDM_REG_NUM_OF_PXP_ASYNC_REQ, 0x0},
{OP_RD, CSDM_REG_NUM_OF_ACK_AFTER_PLACE, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, CSDM_REG_INIT_CREDIT_PXP_CTRL, 0x1},
{OP_WR_ASIC, CSDM_REG_TIMER_TICK, 0x3e8},
{OP_WR_EMUL, CSDM_REG_TIMER_TICK, 0x1},
{OP_WR_FPGA, CSDM_REG_TIMER_TICK, 0xa},
#define CSDM_COMMON_END 440
#define USDM_COMMON_START 440
{OP_WR_E1, USDM_REG_CFC_RSP_START_ADDR, 0xa11},
{OP_WR_E1H, USDM_REG_CFC_RSP_START_ADDR, 0x411},
{OP_WR_E1, USDM_REG_CMP_COUNTER_START_ADDR, 0xa00},
{OP_WR_E1H, USDM_REG_CMP_COUNTER_START_ADDR, 0x400},
{OP_WR_E1, USDM_REG_Q_COUNTER_START_ADDR, 0xa04},
{OP_WR_E1H, USDM_REG_Q_COUNTER_START_ADDR, 0x404},
{OP_WR_E1, USDM_REG_PCK_END_MSG_START_ADDR, 0xa21},
{OP_WR_E1H, USDM_REG_PCK_END_MSG_START_ADDR, 0x421},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, USDM_REG_CMP_COUNTER_MAX0, 0xffff},
{OP_WR, USDM_REG_CMP_COUNTER_MAX1, 0xffff},
{OP_WR, USDM_REG_CMP_COUNTER_MAX2, 0xffff},
{OP_WR, USDM_REG_CMP_COUNTER_MAX3, 0xffff},
{OP_WR, USDM_REG_AGG_INT_EVENT_0, 0x46},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, USDM_REG_AGG_INT_EVENT_1, 0x5},
{OP_WR, USDM_REG_AGG_INT_EVENT_2, 0x34},
{OP_WR, USDM_REG_AGG_INT_EVENT_3, 0x35},
{OP_ZR, USDM_REG_AGG_INT_EVENT_4, 0x5c},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, USDM_REG_AGG_INT_MODE_0, 0x1},
{OP_ZR, USDM_REG_AGG_INT_MODE_1, 0x1f},
{OP_WR, USDM_REG_ENABLE_IN1, 0x7ffffff},
{OP_WR, USDM_REG_ENABLE_IN2, 0x3f},
{OP_WR, USDM_REG_ENABLE_OUT1, 0x7ffffff},
{OP_WR, USDM_REG_ENABLE_OUT2, 0xf},
{OP_RD, USDM_REG_NUM_OF_Q0_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q1_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q2_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q3_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q4_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q5_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q6_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q7_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q8_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q9_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q10_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_Q11_CMD, 0x0},
{OP_RD, USDM_REG_NUM_OF_PKT_END_MSG, 0x0},
{OP_RD, USDM_REG_NUM_OF_PXP_ASYNC_REQ, 0x0},
{OP_RD, USDM_REG_NUM_OF_ACK_AFTER_PLACE, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, USDM_REG_INIT_CREDIT_PXP_CTRL, 0x1},
{OP_WR_ASIC, USDM_REG_TIMER_TICK, 0x3e8},
{OP_WR_EMUL, USDM_REG_TIMER_TICK, 0x1},
{OP_WR_FPGA, USDM_REG_TIMER_TICK, 0xa},
#define USDM_COMMON_END 482
#define CCM_COMMON_START 482
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CCM_REG_XX_OVFL_EVNT_ID, 0x32},
{OP_WR, CCM_REG_CQM_CCM_HDR_P, 0x2150020},
{OP_WR, CCM_REG_CQM_CCM_HDR_S, 0x2150020},
{OP_WR, CCM_REG_ERR_CCM_HDR, 0x8100000},
{OP_WR, CCM_REG_ERR_EVNT_ID, 0x33},
{OP_WR, CCM_REG_TSEM_WEIGHT, 0x0},
{OP_WR, CCM_REG_XSEM_WEIGHT, 0x4},
{OP_WR, CCM_REG_USEM_WEIGHT, 0x4},
{OP_ZR, CCM_REG_PBF_WEIGHT, 0x2},
{OP_WR, CCM_REG_CQM_P_WEIGHT, 0x2},
{OP_WR, CCM_REG_CCM_CQM_USE_Q, 0x1},
{OP_WR, CCM_REG_CNT_AUX1_Q, 0x2},
{OP_WR, CCM_REG_CNT_AUX2_Q, 0x2},
{OP_WR, CCM_REG_INV_DONE_Q, 0x1},
{OP_WR, CCM_REG_GR_ARB_TYPE, 0x1},
{OP_WR, CCM_REG_GR_LD0_PR, 0x1},
{OP_WR, CCM_REG_GR_LD1_PR, 0x2},
{OP_WR, CCM_REG_CFC_INIT_CRD, 0x1},
{OP_WR, CCM_REG_CQM_INIT_CRD, 0x20},
{OP_WR, CCM_REG_FIC0_INIT_CRD, 0x40},
{OP_WR, CCM_REG_FIC1_INIT_CRD, 0x40},
{OP_WR, CCM_REG_XX_INIT_CRD, 0x3},
{OP_WR, CCM_REG_XX_MSG_NUM, 0x18},
{OP_ZR, CCM_REG_XX_TABLE, 0x12},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, CCM_REG_XX_DESCR_TABLE, 0x240238},
{OP_SW_E1H, CCM_REG_XX_DESCR_TABLE, 0x240254},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CCM_REG_N_SM_CTX_LD_0, 0x1},
{OP_WR, CCM_REG_N_SM_CTX_LD_1, 0x2},
{OP_WR, CCM_REG_N_SM_CTX_LD_2, 0x8},
{OP_WR, CCM_REG_N_SM_CTX_LD_3, 0x8},
{OP_ZR, CCM_REG_N_SM_CTX_LD_4, 0x4},
{OP_WR, CCM_REG_CCM_REG0_SZ, 0x4},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM0_0, 0x9},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM0_1, 0x29},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM1_0, 0xa},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM1_1, 0x2a},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM2_0, 0x7},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM2_1, 0x27},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM3_0, 0x7},
{OP_WR_E1, CCM_REG_QOS_PHYS_QNUM3_1, 0x27},
{OP_WR_E1, CCM_REG_PHYS_QNUM1_0, 0xc},
{OP_WR_E1, CCM_REG_PHYS_QNUM1_1, 0x2c},
{OP_WR_E1, CCM_REG_PHYS_QNUM2_0, 0xc},
{OP_WR_E1, CCM_REG_PHYS_QNUM2_1, 0x2c},
{OP_WR_E1, CCM_REG_PHYS_QNUM3_0, 0xc},
{OP_WR_E1, CCM_REG_PHYS_QNUM3_1, 0x2c},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CCM_REG_CCM_STORM0_IFEN, 0x1},
{OP_WR, CCM_REG_CCM_STORM1_IFEN, 0x1},
{OP_WR, CCM_REG_CCM_CQM_IFEN, 0x1},
{OP_WR, CCM_REG_STORM_CCM_IFEN, 0x1},
{OP_WR, CCM_REG_CQM_CCM_IFEN, 0x1},
{OP_WR, CCM_REG_CSDM_IFEN, 0x1},
{OP_WR, CCM_REG_TSEM_IFEN, 0x1},
{OP_WR, CCM_REG_XSEM_IFEN, 0x1},
{OP_WR, CCM_REG_USEM_IFEN, 0x1},
{OP_WR, CCM_REG_PBF_IFEN, 0x1},
{OP_WR, CCM_REG_CDU_AG_WR_IFEN, 0x1},
{OP_WR, CCM_REG_CDU_AG_RD_IFEN, 0x1},
{OP_WR, CCM_REG_CDU_SM_WR_IFEN, 0x1},
{OP_WR, CCM_REG_CDU_SM_RD_IFEN, 0x1},
{OP_WR, CCM_REG_CCM_CFC_IFEN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define CCM_COMMON_END 543
#define CCM_FUNC0_START 543
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_0, 0x9},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_0, 0xa},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_0, 0x7},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_0, 0x7},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_0, 0xc},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_0, 0xb},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_0, 0x7},
#define CCM_FUNC0_END 550
#define CCM_FUNC1_START 550
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_1, 0x29},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_1, 0x2a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_1, 0x27},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_1, 0x27},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_1, 0x2c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_1, 0x2b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_1, 0x27},
#define CCM_FUNC1_END 557
#define CCM_FUNC2_START 557
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_0, 0x19},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_0, 0x1a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_0, 0x17},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_0, 0x17},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_0, 0x1c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_0, 0x1b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_0, 0x17},
#define CCM_FUNC2_END 564
#define CCM_FUNC3_START 564
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_1, 0x39},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_1, 0x3a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_1, 0x37},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_1, 0x37},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_1, 0x3c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_1, 0x3b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_1, 0x37},
#define CCM_FUNC3_END 571
#define CCM_FUNC4_START 571
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_0, 0x49},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_0, 0x4a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_0, 0x47},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_0, 0x47},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_0, 0x4c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_0, 0x4b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_0, 0x47},
#define CCM_FUNC4_END 578
#define CCM_FUNC5_START 578
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_1, 0x69},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_1, 0x6a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_1, 0x67},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_1, 0x67},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_1, 0x6c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_1, 0x6b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_1, 0x67},
#define CCM_FUNC5_END 585
#define CCM_FUNC6_START 585
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_0, 0x59},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_0, 0x5a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_0, 0x57},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_0, 0x57},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_0, 0x5c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_0, 0x5b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_0, 0x57},
#define CCM_FUNC6_END 592
#define CCM_FUNC7_START 592
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM0_1, 0x79},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM1_1, 0x7a},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM2_1, 0x77},
{OP_WR_E1H, CCM_REG_QOS_PHYS_QNUM3_1, 0x77},
{OP_WR_E1H, CCM_REG_PHYS_QNUM1_1, 0x7c},
{OP_WR_E1H, CCM_REG_PHYS_QNUM2_1, 0x7b},
{OP_WR_E1H, CCM_REG_PHYS_QNUM3_1, 0x77},
#define CCM_FUNC7_END 599
#define UCM_COMMON_START 599
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, UCM_REG_XX_OVFL_EVNT_ID, 0x32},
{OP_WR, UCM_REG_UQM_UCM_HDR_P, 0x2150020},
{OP_WR, UCM_REG_UQM_UCM_HDR_S, 0x2150020},
{OP_WR, UCM_REG_TM_UCM_HDR, 0x30},
{OP_WR, UCM_REG_ERR_UCM_HDR, 0x8100000},
{OP_WR, UCM_REG_ERR_EVNT_ID, 0x33},
{OP_WR, UCM_REG_EXPR_EVNT_ID, 0x30},
{OP_WR, UCM_REG_STOP_EVNT_ID, 0x31},
{OP_WR, UCM_REG_TSEM_WEIGHT, 0x3},
{OP_WR, UCM_REG_CSEM_WEIGHT, 0x0},
{OP_WR, UCM_REG_CP_WEIGHT, 0x0},
{OP_WR, UCM_REG_UQM_P_WEIGHT, 0x6},
{OP_WR, UCM_REG_UCM_UQM_USE_Q, 0x1},
{OP_WR, UCM_REG_INV_CFLG_Q, 0x1},
{OP_WR, UCM_REG_GR_ARB_TYPE, 0x1},
{OP_WR, UCM_REG_GR_LD0_PR, 0x1},
{OP_WR, UCM_REG_GR_LD1_PR, 0x2},
{OP_WR, UCM_REG_CFC_INIT_CRD, 0x1},
{OP_WR, UCM_REG_FIC0_INIT_CRD, 0x40},
{OP_WR, UCM_REG_FIC1_INIT_CRD, 0x40},
{OP_WR, UCM_REG_TM_INIT_CRD, 0x4},
{OP_WR, UCM_REG_UQM_INIT_CRD, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, UCM_REG_XX_INIT_CRD, 0xe},
{OP_WR, UCM_REG_XX_MSG_NUM, 0x1b},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, UCM_REG_XX_TABLE, 0x12},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, UCM_REG_XX_DESCR_TABLE, 0x1b025c},
{OP_SW_E1H, UCM_REG_XX_DESCR_TABLE, 0x1b0278},
{OP_WR, UCM_REG_N_SM_CTX_LD_0, 0x10},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, UCM_REG_N_SM_CTX_LD_1, 0x7},
{OP_WR, UCM_REG_N_SM_CTX_LD_2, 0xf},
{OP_WR, UCM_REG_N_SM_CTX_LD_3, 0x10},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, UCM_REG_N_SM_CTX_LD_4, 0x4},
{OP_WR_E1H, UCM_REG_N_SM_CTX_LD_4, 0xd},
{OP_ZR_E1H, UCM_REG_N_SM_CTX_LD_5, 0x3},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, UCM_REG_UCM_REG0_SZ, 0x3},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, UCM_REG_PHYS_QNUM0_0, 0xf},
{OP_WR_E1, UCM_REG_PHYS_QNUM0_1, 0x2f},
{OP_WR_E1, UCM_REG_PHYS_QNUM1_0, 0xe},
{OP_WR_E1, UCM_REG_PHYS_QNUM1_1, 0x2e},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, UCM_REG_UCM_STORM0_IFEN, 0x1},
{OP_WR, UCM_REG_UCM_STORM1_IFEN, 0x1},
{OP_WR, UCM_REG_UCM_UQM_IFEN, 0x1},
{OP_WR, UCM_REG_STORM_UCM_IFEN, 0x1},
{OP_WR, UCM_REG_UQM_UCM_IFEN, 0x1},
{OP_WR, UCM_REG_USDM_IFEN, 0x1},
{OP_WR, UCM_REG_TM_UCM_IFEN, 0x1},
{OP_WR, UCM_REG_UCM_TM_IFEN, 0x1},
{OP_WR, UCM_REG_TSEM_IFEN, 0x1},
{OP_WR, UCM_REG_CSEM_IFEN, 0x1},
{OP_WR, UCM_REG_XSEM_IFEN, 0x1},
{OP_WR, UCM_REG_DORQ_IFEN, 0x1},
{OP_WR, UCM_REG_CDU_AG_WR_IFEN, 0x1},
{OP_WR, UCM_REG_CDU_AG_RD_IFEN, 0x1},
{OP_WR, UCM_REG_CDU_SM_WR_IFEN, 0x1},
{OP_WR, UCM_REG_CDU_SM_RD_IFEN, 0x1},
{OP_WR, UCM_REG_UCM_CFC_IFEN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define UCM_COMMON_END 655
#define UCM_FUNC0_START 655
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_0, 0xf},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_0, 0xe},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_0, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_0, 0x0},
#define UCM_FUNC0_END 659
#define UCM_FUNC1_START 659
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_1, 0x2f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_1, 0x2e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_1, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_1, 0x0},
#define UCM_FUNC1_END 663
#define UCM_FUNC2_START 663
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_0, 0x1f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_0, 0x1e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_0, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_0, 0x0},
#define UCM_FUNC2_END 667
#define UCM_FUNC3_START 667
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_1, 0x3f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_1, 0x3e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_1, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_1, 0x0},
#define UCM_FUNC3_END 671
#define UCM_FUNC4_START 671
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_0, 0x4f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_0, 0x4e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_0, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_0, 0x0},
#define UCM_FUNC4_END 675
#define UCM_FUNC5_START 675
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_1, 0x6f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_1, 0x6e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_1, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_1, 0x0},
#define UCM_FUNC5_END 679
#define UCM_FUNC6_START 679
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_0, 0x5f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_0, 0x5e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_0, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_0, 0x0},
#define UCM_FUNC6_END 683
#define UCM_FUNC7_START 683
{OP_WR_E1H, UCM_REG_PHYS_QNUM0_1, 0x7f},
{OP_WR_E1H, UCM_REG_PHYS_QNUM1_1, 0x7e},
{OP_WR_E1H, UCM_REG_PHYS_QNUM2_1, 0x0},
{OP_WR_E1H, UCM_REG_PHYS_QNUM3_1, 0x0},
#define UCM_FUNC7_END 687
#define USEM_COMMON_START 687
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_RD, USEM_REG_MSG_NUM_FIC0, 0x0},
{OP_RD, USEM_REG_MSG_NUM_FIC1, 0x0},
{OP_RD, USEM_REG_MSG_NUM_FOC0, 0x0},
{OP_RD, USEM_REG_MSG_NUM_FOC1, 0x0},
{OP_RD, USEM_REG_MSG_NUM_FOC2, 0x0},
{OP_RD, USEM_REG_MSG_NUM_FOC3, 0x0},
{OP_WR, USEM_REG_ARB_ELEMENT0, 0x1},
{OP_WR, USEM_REG_ARB_ELEMENT1, 0x2},
{OP_WR, USEM_REG_ARB_ELEMENT2, 0x3},
{OP_WR, USEM_REG_ARB_ELEMENT3, 0x0},
{OP_WR, USEM_REG_ARB_ELEMENT4, 0x4},
{OP_WR, USEM_REG_ARB_CYCLE_SIZE, 0x1},
{OP_WR, USEM_REG_TS_0_AS, 0x0},
{OP_WR, USEM_REG_TS_1_AS, 0x1},
{OP_WR, USEM_REG_TS_2_AS, 0x4},
{OP_WR, USEM_REG_TS_3_AS, 0x0},
{OP_WR, USEM_REG_TS_4_AS, 0x1},
{OP_WR, USEM_REG_TS_5_AS, 0x3},
{OP_WR, USEM_REG_TS_6_AS, 0x0},
{OP_WR, USEM_REG_TS_7_AS, 0x1},
{OP_WR, USEM_REG_TS_8_AS, 0x4},
{OP_WR, USEM_REG_TS_9_AS, 0x0},
{OP_WR, USEM_REG_TS_10_AS, 0x1},
{OP_WR, USEM_REG_TS_11_AS, 0x3},
{OP_WR, USEM_REG_TS_12_AS, 0x0},
{OP_WR, USEM_REG_TS_13_AS, 0x1},
{OP_WR, USEM_REG_TS_14_AS, 0x4},
{OP_WR, USEM_REG_TS_15_AS, 0x0},
{OP_WR, USEM_REG_TS_16_AS, 0x4},
{OP_WR, USEM_REG_TS_17_AS, 0x3},
{OP_ZR, USEM_REG_TS_18_AS, 0x2},
{OP_WR, USEM_REG_ENABLE_IN, 0x3fff},
{OP_WR, USEM_REG_ENABLE_OUT, 0x3ff},
{OP_WR, USEM_REG_FIC0_DISABLE, 0x0},
{OP_WR, USEM_REG_FIC1_DISABLE, 0x0},
{OP_WR, USEM_REG_PAS_DISABLE, 0x0},
{OP_WR, USEM_REG_THREADS_LIST, 0xffff},
{OP_ZR, USEM_REG_PASSIVE_BUFFER, 0x800},
{OP_WR, USEM_REG_FAST_MEMORY + 0x18bc0, 0x1},
{OP_WR, USEM_REG_FAST_MEMORY + 0x18000, 0x1a},
{OP_WR, USEM_REG_FAST_MEMORY + 0x18040, 0x4e},
{OP_WR, USEM_REG_FAST_MEMORY + 0x18080, 0x10},
{OP_WR, USEM_REG_FAST_MEMORY + 0x180c0, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_ASIC, USEM_REG_FAST_MEMORY + 0x18300, 0x7a120},
{OP_WR_EMUL, USEM_REG_FAST_MEMORY + 0x18300, 0x138},
{OP_WR_FPGA, USEM_REG_FAST_MEMORY + 0x18300, 0x1388},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, USEM_REG_FAST_MEMORY + 0x183c0, 0x1f4},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_ASIC, USEM_REG_FAST_MEMORY + 0x18380, 0x1dcd6500},
{OP_WR_EMUL, USEM_REG_FAST_MEMORY + 0x18380, 0x4c4b4},
{OP_WR_FPGA, USEM_REG_FAST_MEMORY + 0x18380, 0x4c4b40},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x5000, 0x102},
{OP_WR_EMUL_E1H, USEM_REG_FAST_MEMORY + 0x11480, 0x0},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1020, 0xc8},
{OP_WR_E1H, USEM_REG_FAST_MEMORY + 0x11480, 0x1},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1000, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x2000, 0x102},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x57e8, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x8020, 0xc8},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x57d0, 0x5},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x8000, 0x2},
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x57d0 + 0x14, 0x10277},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3760, 0x4},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1e20, 0x42},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3738, 0x9},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3000, 0x400},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x3738 + 0x24, 0x10293},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c00, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3180, 0x42},
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x2c00 + 0x8, 0x20278},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5000, 0x400},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b68, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4000, 0x2},
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x4b68 + 0x8, 0x2027a},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x4000 + 0x8, 0x20294},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b10, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b68, 0x2},
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x2830, 0x2027c},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x6b68 + 0x8, 0x20296},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b10, 0x2},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x74c0, 0x20298},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, USEM_REG_FAST_MEMORY + 0x10800, 0x1000000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c00, 0x10027e},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x10c00, 0x10029a},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, USEM_REG_FAST_MEMORY + 0x10800, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, USEM_REG_FAST_MEMORY + 0x10c40, 0x10028e},
{OP_SW_E1H, USEM_REG_FAST_MEMORY + 0x10c40, 0x1002aa},
{OP_ZP_E1, USEM_REG_INT_TABLE, 0xc20000},
{OP_ZP_E1H, USEM_REG_INT_TABLE, 0xc40000},
{OP_WR_64_E1, USEM_REG_INT_TABLE + 0x368, 0x13029e},
{OP_WR_64_E1H, USEM_REG_INT_TABLE + 0x368, 0x1302ba},
{OP_ZP_E1, USEM_REG_PRAM, 0x975a0000},
{OP_ZP_E1H, USEM_REG_PRAM, 0x985c0000},
{OP_WR_64_E1, USEM_REG_PRAM + 0x17f90, 0x500e02a0},
{OP_WR_64_E1H, USEM_REG_PRAM + 0x18200, 0x4fc002bc},
#define USEM_COMMON_END 781
#define USEM_PORT0_START 781
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1400, 0xa0},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9000, 0xa0},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1900, 0xa},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9500, 0x28},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1950, 0x2e},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9640, 0x34},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1d00, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3080, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1d20, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3288, 0x96},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x5440, 0x72},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5000, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3000, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5100, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3100, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5200, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3200, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5300, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3300, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5400, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3400, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5500, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3500, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5600, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3600, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5700, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3700, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5800, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3800, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5900, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3900, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5a00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3a00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5b00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3b00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5c00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3c00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5d00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3d00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5e00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3e00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5f00, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3f00, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6b78, 0x52},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c10, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6e08, 0xc},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4b78, 0x52},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e08, 0xc},
#define USEM_PORT0_END 829
#define USEM_PORT1_START 829
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1680, 0xa0},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9280, 0xa0},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1928, 0xa},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x95a0, 0x28},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1a08, 0x2e},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x9710, 0x34},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1d10, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3100, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x1da0, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x34e0, 0x96},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x5608, 0x72},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5080, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3080, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5180, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3180, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5280, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3280, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5380, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3380, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5480, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3480, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5580, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3580, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5680, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3680, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5780, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3780, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5880, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3880, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5980, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3980, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5a80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3a80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5b80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3b80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5c80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3c80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5d80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3d80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5e80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3e80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x5f80, 0x20},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x3f80, 0x20},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6cc0, 0x52},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x2c20, 0x2},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x6e38, 0xc},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4cc0, 0x52},
{OP_ZR_E1, USEM_REG_FAST_MEMORY + 0x4e38, 0xc},
#define USEM_PORT1_END 877
#define USEM_FUNC0_START 877
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3000, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4010, 0x2},
#define USEM_FUNC0_END 879
#define USEM_FUNC1_START 879
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3010, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4020, 0x2},
#define USEM_FUNC1_END 881
#define USEM_FUNC2_START 881
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3020, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4030, 0x2},
#define USEM_FUNC2_END 883
#define USEM_FUNC3_START 883
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3030, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4040, 0x2},
#define USEM_FUNC3_END 885
#define USEM_FUNC4_START 885
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3040, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4050, 0x2},
#define USEM_FUNC4_END 887
#define USEM_FUNC5_START 887
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3050, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4060, 0x2},
#define USEM_FUNC5_END 889
#define USEM_FUNC6_START 889
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3060, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4070, 0x2},
#define USEM_FUNC6_END 891
#define USEM_FUNC7_START 891
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x3070, 0x4},
{OP_ZR_E1H, USEM_REG_FAST_MEMORY + 0x4080, 0x2},
#define USEM_FUNC7_END 893
#define CSEM_COMMON_START 893
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_RD, CSEM_REG_MSG_NUM_FIC0, 0x0},
{OP_RD, CSEM_REG_MSG_NUM_FIC1, 0x0},
{OP_RD, CSEM_REG_MSG_NUM_FOC0, 0x0},
{OP_RD, CSEM_REG_MSG_NUM_FOC1, 0x0},
{OP_RD, CSEM_REG_MSG_NUM_FOC2, 0x0},
{OP_RD, CSEM_REG_MSG_NUM_FOC3, 0x0},
{OP_WR, CSEM_REG_ARB_ELEMENT0, 0x1},
{OP_WR, CSEM_REG_ARB_ELEMENT1, 0x2},
{OP_WR, CSEM_REG_ARB_ELEMENT2, 0x3},
{OP_WR, CSEM_REG_ARB_ELEMENT3, 0x0},
{OP_WR, CSEM_REG_ARB_ELEMENT4, 0x4},
{OP_WR, CSEM_REG_ARB_CYCLE_SIZE, 0x1},
{OP_WR, CSEM_REG_TS_0_AS, 0x0},
{OP_WR, CSEM_REG_TS_1_AS, 0x1},
{OP_WR, CSEM_REG_TS_2_AS, 0x4},
{OP_WR, CSEM_REG_TS_3_AS, 0x0},
{OP_WR, CSEM_REG_TS_4_AS, 0x1},
{OP_WR, CSEM_REG_TS_5_AS, 0x3},
{OP_WR, CSEM_REG_TS_6_AS, 0x0},
{OP_WR, CSEM_REG_TS_7_AS, 0x1},
{OP_WR, CSEM_REG_TS_8_AS, 0x4},
{OP_WR, CSEM_REG_TS_9_AS, 0x0},
{OP_WR, CSEM_REG_TS_10_AS, 0x1},
{OP_WR, CSEM_REG_TS_11_AS, 0x3},
{OP_WR, CSEM_REG_TS_12_AS, 0x0},
{OP_WR, CSEM_REG_TS_13_AS, 0x1},
{OP_WR, CSEM_REG_TS_14_AS, 0x4},
{OP_WR, CSEM_REG_TS_15_AS, 0x0},
{OP_WR, CSEM_REG_TS_16_AS, 0x4},
{OP_WR, CSEM_REG_TS_17_AS, 0x3},
{OP_ZR, CSEM_REG_TS_18_AS, 0x2},
{OP_WR, CSEM_REG_ENABLE_IN, 0x3fff},
{OP_WR, CSEM_REG_ENABLE_OUT, 0x3ff},
{OP_WR, CSEM_REG_FIC0_DISABLE, 0x0},
{OP_WR, CSEM_REG_FIC1_DISABLE, 0x0},
{OP_WR, CSEM_REG_PAS_DISABLE, 0x0},
{OP_WR, CSEM_REG_THREADS_LIST, 0xffff},
{OP_ZR, CSEM_REG_PASSIVE_BUFFER, 0x800},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x18bc0, 0x1},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x18000, 0x10},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x18040, 0x12},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x18080, 0x30},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x180c0, 0xe},
{OP_WR, CSEM_REG_FAST_MEMORY + 0x183c0, 0x1f4},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x5000, 0x42},
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x11480, 0x1},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1020, 0xc8},
{OP_WR_EMUL_E1H, CSEM_REG_FAST_MEMORY + 0x11480, 0x0},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1000, 0x2},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x1000, 0x42},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x2000, 0xc0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x7020, 0xc8},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x3070, 0x80},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x7000, 0x2},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x4280, 0x4},
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x11e8, 0x0},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x25c0, 0x240},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3000, 0xc0},
{OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x2ec8, 0x802a2},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x4070, 0x80},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x5280, 0x4},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6280, 0x240},
{OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x6b88, 0x2002be},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CSEM_REG_FAST_MEMORY + 0x10800, 0x13fffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c00, 0x1002aa},
{OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x10c00, 0x1002de},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CSEM_REG_FAST_MEMORY + 0x10800, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, CSEM_REG_FAST_MEMORY + 0x10c40, 0x1002ba},
{OP_SW_E1H, CSEM_REG_FAST_MEMORY + 0x10c40, 0x1002ee},
{OP_ZP_E1, CSEM_REG_INT_TABLE, 0x6e0000},
{OP_ZP_E1H, CSEM_REG_INT_TABLE, 0x6f0000},
{OP_WR_64_E1, CSEM_REG_INT_TABLE + 0x380, 0x1002ca},
{OP_WR_64_E1H, CSEM_REG_INT_TABLE + 0x380, 0x1002fe},
{OP_ZP_E1, CSEM_REG_PRAM, 0x48bc0000},
{OP_ZP_E1H, CSEM_REG_PRAM, 0x493d0000},
{OP_WR_64_E1, CSEM_REG_PRAM + 0xb210, 0x682402cc},
{OP_WR_64_E1H, CSEM_REG_PRAM + 0xb430, 0x67e00300},
#define CSEM_COMMON_END 970
#define CSEM_PORT0_START 970
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1400, 0xa0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8000, 0xa0},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1900, 0x10},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8500, 0x40},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1980, 0x30},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8700, 0x3c},
{OP_WR_E1, CSEM_REG_FAST_MEMORY + 0x5118, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x4040, 0x6},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x2300, 0xe},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6040, 0x30},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x3040, 0x6},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x2410, 0x30},
#define CSEM_PORT0_END 982
#define CSEM_PORT1_START 982
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1680, 0xa0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8280, 0xa0},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1940, 0x10},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x8600, 0x40},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x1a40, 0x30},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x87f0, 0x3c},
{OP_WR_E1, CSEM_REG_FAST_MEMORY + 0x511c, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x4058, 0x6},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x2338, 0xe},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x6100, 0x30},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x3058, 0x6},
{OP_ZR_E1, CSEM_REG_FAST_MEMORY + 0x24d0, 0x30},
#define CSEM_PORT1_END 994
#define CSEM_FUNC0_START 994
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1148, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3300, 0x2},
#define CSEM_FUNC0_END 996
#define CSEM_FUNC1_START 996
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x114c, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3308, 0x2},
#define CSEM_FUNC1_END 998
#define CSEM_FUNC2_START 998
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1150, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3310, 0x2},
#define CSEM_FUNC2_END 1000
#define CSEM_FUNC3_START 1000
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1154, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3318, 0x2},
#define CSEM_FUNC3_END 1002
#define CSEM_FUNC4_START 1002
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1158, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3320, 0x2},
#define CSEM_FUNC4_END 1004
#define CSEM_FUNC5_START 1004
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x115c, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3328, 0x2},
#define CSEM_FUNC5_END 1006
#define CSEM_FUNC6_START 1006
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1160, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3330, 0x2},
#define CSEM_FUNC6_END 1008
#define CSEM_FUNC7_START 1008
{OP_WR_E1H, CSEM_REG_FAST_MEMORY + 0x1164, 0x0},
{OP_ZR_E1H, CSEM_REG_FAST_MEMORY + 0x3338, 0x2},
#define CSEM_FUNC7_END 1010
#define XPB_COMMON_START 1010
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, GRCBASE_XPB + PB_REG_CONTROL, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define XPB_COMMON_END 1011
#define DQ_COMMON_START 1011
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, DORQ_REG_MODE_ACT, 0x2},
{OP_WR, DORQ_REG_NORM_CID_OFST, 0x3},
{OP_WR, DORQ_REG_OUTST_REQ, 0x4},
{OP_WR, DORQ_REG_DPM_CID_ADDR, 0x8},
{OP_WR, DORQ_REG_RSP_INIT_CRD, 0x2},
{OP_WR, DORQ_REG_NORM_CMHEAD_TX, 0x90},
{OP_WR, DORQ_REG_CMHEAD_RX, 0x90},
{OP_WR, DORQ_REG_SHRT_CMHEAD, 0x800090},
{OP_WR, DORQ_REG_ERR_CMHEAD, 0x8140000},
{OP_WR, DORQ_REG_AGG_CMD0, 0x8a},
{OP_WR, DORQ_REG_AGG_CMD1, 0x80},
{OP_WR, DORQ_REG_AGG_CMD2, 0x90},
{OP_WR, DORQ_REG_AGG_CMD3, 0x80},
{OP_WR, DORQ_REG_SHRT_ACT_CNT, 0x6},
{OP_WR, DORQ_REG_DQ_FIFO_FULL_TH, 0x7d0},
{OP_WR, DORQ_REG_DQ_FIFO_AFULL_TH, 0x76c},
{OP_WR, DORQ_REG_REGN, 0x7c1004},
{OP_WR, DORQ_REG_IF_EN, 0xf},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define DQ_COMMON_END 1029
#define TIMERS_COMMON_START 1029
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, TM_REG_CLIN_PRIOR0_CLIENT, 0x2},
{OP_WR, TM_REG_LIN_SETCLR_FIFO_ALFULL_THR, 0x1c},
{OP_WR, TM_REG_CFC_AC_CRDCNT_VAL, 0x1},
{OP_WR, TM_REG_CFC_CLD_CRDCNT_VAL, 0x1},
{OP_WR, TM_REG_CLOUT_CRDCNT0_VAL, 0x1},
{OP_WR, TM_REG_CLOUT_CRDCNT1_VAL, 0x1},
{OP_WR, TM_REG_CLOUT_CRDCNT2_VAL, 0x1},
{OP_WR, TM_REG_EXP_CRDCNT_VAL, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, TM_REG_PCIARB_CRDCNT_VAL, 0x1},
{OP_WR_E1H, TM_REG_PCIARB_CRDCNT_VAL, 0x2},
{OP_WR_ASIC, TM_REG_TIMER_TICK_SIZE, 0x3d090},
{OP_WR_EMUL, TM_REG_TIMER_TICK_SIZE, 0x9c},
{OP_WR_FPGA, TM_REG_TIMER_TICK_SIZE, 0x9c4},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, TM_REG_CL0_CONT_REGION, 0x8},
{OP_WR, TM_REG_CL1_CONT_REGION, 0xc},
{OP_WR, TM_REG_CL2_CONT_REGION, 0x10},
{OP_WR, TM_REG_TM_CONTEXT_REGION, 0x20},
{OP_WR, TM_REG_EN_TIMERS, 0x1},
{OP_WR, TM_REG_EN_REAL_TIME_CNT, 0x1},
{OP_WR, TM_REG_EN_CL0_INPUT, 0x1},
{OP_WR, TM_REG_EN_CL1_INPUT, 0x1},
{OP_WR, TM_REG_EN_CL2_INPUT, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define TIMERS_COMMON_END 1051
#define TIMERS_PORT0_START 1051
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, TM_REG_LIN0_PHY_ADDR, 0x2},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define TIMERS_PORT0_END 1052
#define TIMERS_PORT1_START 1052
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, TM_REG_LIN1_PHY_ADDR, 0x2},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define TIMERS_PORT1_END 1053
#define XSDM_COMMON_START 1053
{OP_WR_E1, XSDM_REG_CFC_RSP_START_ADDR, 0x614},
{OP_WR_E1H, XSDM_REG_CFC_RSP_START_ADDR, 0x424},
{OP_WR_E1, XSDM_REG_CMP_COUNTER_START_ADDR, 0x600},
{OP_WR_E1H, XSDM_REG_CMP_COUNTER_START_ADDR, 0x410},
{OP_WR_E1, XSDM_REG_Q_COUNTER_START_ADDR, 0x604},
{OP_WR_E1H, XSDM_REG_Q_COUNTER_START_ADDR, 0x414},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSDM_REG_CMP_COUNTER_MAX0, 0xffff},
{OP_WR, XSDM_REG_CMP_COUNTER_MAX1, 0xffff},
{OP_WR, XSDM_REG_CMP_COUNTER_MAX2, 0xffff},
{OP_WR, XSDM_REG_CMP_COUNTER_MAX3, 0xffff},
{OP_WR, XSDM_REG_AGG_INT_EVENT_0, 0x20},
{OP_WR, XSDM_REG_AGG_INT_EVENT_1, 0x20},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, XSDM_REG_AGG_INT_EVENT_2, 0x34},
{OP_WR, XSDM_REG_AGG_INT_EVENT_3, 0x35},
{OP_WR, XSDM_REG_AGG_INT_EVENT_4, 0x23},
{OP_WR, XSDM_REG_AGG_INT_EVENT_5, 0x24},
{OP_WR, XSDM_REG_AGG_INT_EVENT_6, 0x25},
{OP_WR, XSDM_REG_AGG_INT_EVENT_7, 0x26},
{OP_WR, XSDM_REG_AGG_INT_EVENT_8, 0x27},
{OP_WR, XSDM_REG_AGG_INT_EVENT_9, 0x29},
{OP_WR, XSDM_REG_AGG_INT_EVENT_10, 0x2a},
{OP_WR, XSDM_REG_AGG_INT_EVENT_11, 0x2b},
{OP_ZR, XSDM_REG_AGG_INT_EVENT_12, 0x54},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSDM_REG_AGG_INT_MODE_0, 0x1},
{OP_ZR, XSDM_REG_AGG_INT_MODE_1, 0x1f},
{OP_WR, XSDM_REG_ENABLE_IN1, 0x7ffffff},
{OP_WR, XSDM_REG_ENABLE_IN2, 0x3f},
{OP_WR, XSDM_REG_ENABLE_OUT1, 0x7ffffff},
{OP_WR, XSDM_REG_ENABLE_OUT2, 0xf},
{OP_RD, XSDM_REG_NUM_OF_Q0_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q1_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q3_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q4_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q5_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q6_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q7_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q8_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q9_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q10_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_Q11_CMD, 0x0},
{OP_RD, XSDM_REG_NUM_OF_PKT_END_MSG, 0x0},
{OP_RD, XSDM_REG_NUM_OF_PXP_ASYNC_REQ, 0x0},
{OP_RD, XSDM_REG_NUM_OF_ACK_AFTER_PLACE, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, XSDM_REG_INIT_CREDIT_PXP_CTRL, 0x1},
{OP_WR_ASIC, XSDM_REG_TIMER_TICK, 0x3e8},
{OP_WR_EMUL, XSDM_REG_TIMER_TICK, 0x1},
{OP_WR_FPGA, XSDM_REG_TIMER_TICK, 0xa},
#define XSDM_COMMON_END 1100
#define QM_COMMON_START 1100
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_ACTCTRINITVAL_0, 0x6},
{OP_WR, QM_REG_ACTCTRINITVAL_1, 0x5},
{OP_WR, QM_REG_ACTCTRINITVAL_2, 0xa},
{OP_WR, QM_REG_ACTCTRINITVAL_3, 0x5},
{OP_WR, QM_REG_PCIREQAT, 0x2},
{OP_WR, QM_REG_CMINITCRD_0, 0x4},
{OP_WR, QM_REG_CMINITCRD_1, 0x4},
{OP_WR, QM_REG_CMINITCRD_2, 0x4},
{OP_WR, QM_REG_CMINITCRD_3, 0x4},
{OP_WR, QM_REG_CMINITCRD_4, 0x4},
{OP_WR, QM_REG_CMINITCRD_5, 0x4},
{OP_WR, QM_REG_CMINITCRD_6, 0x4},
{OP_WR, QM_REG_CMINITCRD_7, 0x4},
{OP_WR, QM_REG_OUTLDREQ, 0x4},
{OP_WR, QM_REG_CTXREG_0, 0x7c},
{OP_WR, QM_REG_CTXREG_1, 0x3d},
{OP_WR, QM_REG_CTXREG_2, 0x3f},
{OP_WR, QM_REG_CTXREG_3, 0x9c},
{OP_WR, QM_REG_ENSEC, 0x7},
{OP_ZR, QM_REG_QVOQIDX_0, 0x5},
{OP_WR, QM_REG_WRRWEIGHTS_0, 0x1010101},
{OP_WR, QM_REG_QVOQIDX_5, 0x0},
{OP_WR, QM_REG_QVOQIDX_6, 0x4},
{OP_WR, QM_REG_QVOQIDX_7, 0x4},
{OP_WR, QM_REG_QVOQIDX_8, 0x2},
{OP_WR, QM_REG_WRRWEIGHTS_1, 0x8012004},
{OP_WR, QM_REG_QVOQIDX_9, 0x5},
{OP_WR, QM_REG_QVOQIDX_10, 0x5},
{OP_WR, QM_REG_QVOQIDX_11, 0x5},
{OP_WR, QM_REG_QVOQIDX_12, 0x5},
{OP_WR, QM_REG_WRRWEIGHTS_2, 0x20081001},
{OP_WR, QM_REG_QVOQIDX_13, 0x8},
{OP_WR, QM_REG_QVOQIDX_14, 0x6},
{OP_WR, QM_REG_QVOQIDX_15, 0x7},
{OP_WR, QM_REG_QVOQIDX_16, 0x0},
{OP_WR, QM_REG_WRRWEIGHTS_3, 0x1010120},
{OP_ZR, QM_REG_QVOQIDX_17, 0x4},
{OP_WR, QM_REG_WRRWEIGHTS_4, 0x1010101},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, QM_REG_QVOQIDX_21, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_21, 0x0},
{OP_WR_E1, QM_REG_WRRWEIGHTS_5, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_22, 0x4},
{OP_ZR_E1, QM_REG_QVOQIDX_25, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_23, 0x4},
{OP_WR_E1, QM_REG_WRRWEIGHTS_6, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_24, 0x2},
{OP_ZR_E1, QM_REG_QVOQIDX_29, 0x3},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_5, 0x8012004},
{OP_WR_E1H, QM_REG_QVOQIDX_25, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_26, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_27, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_28, 0x5},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_6, 0x20081001},
{OP_WR_E1H, QM_REG_QVOQIDX_29, 0x8},
{OP_WR_E1H, QM_REG_QVOQIDX_30, 0x6},
{OP_WR_E1H, QM_REG_QVOQIDX_31, 0x7},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_QVOQIDX_32, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_WRRWEIGHTS_7, 0x1010101},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_7, 0x1010120},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_QVOQIDX_33, 0x1},
{OP_WR, QM_REG_QVOQIDX_34, 0x1},
{OP_WR, QM_REG_QVOQIDX_35, 0x1},
{OP_WR, QM_REG_QVOQIDX_36, 0x1},
{OP_WR, QM_REG_WRRWEIGHTS_8, 0x1010101},
{OP_WR, QM_REG_QVOQIDX_37, 0x1},
{OP_WR, QM_REG_QVOQIDX_38, 0x4},
{OP_WR, QM_REG_QVOQIDX_39, 0x4},
{OP_WR, QM_REG_QVOQIDX_40, 0x2},
{OP_WR, QM_REG_WRRWEIGHTS_9, 0x8012004},
{OP_WR, QM_REG_QVOQIDX_41, 0x5},
{OP_WR, QM_REG_QVOQIDX_42, 0x5},
{OP_WR, QM_REG_QVOQIDX_43, 0x5},
{OP_WR, QM_REG_QVOQIDX_44, 0x5},
{OP_WR, QM_REG_WRRWEIGHTS_10, 0x20081001},
{OP_WR, QM_REG_QVOQIDX_45, 0x8},
{OP_WR, QM_REG_QVOQIDX_46, 0x6},
{OP_WR, QM_REG_QVOQIDX_47, 0x7},
{OP_WR, QM_REG_QVOQIDX_48, 0x1},
{OP_WR, QM_REG_WRRWEIGHTS_11, 0x1010120},
{OP_WR, QM_REG_QVOQIDX_49, 0x1},
{OP_WR, QM_REG_QVOQIDX_50, 0x1},
{OP_WR, QM_REG_QVOQIDX_51, 0x1},
{OP_WR, QM_REG_QVOQIDX_52, 0x1},
{OP_WR, QM_REG_WRRWEIGHTS_12, 0x1010101},
{OP_WR, QM_REG_QVOQIDX_53, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_QVOQIDX_54, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_54, 0x4},
{OP_WR_E1, QM_REG_QVOQIDX_55, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_55, 0x4},
{OP_WR_E1, QM_REG_QVOQIDX_56, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_56, 0x2},
{OP_WR_E1, QM_REG_WRRWEIGHTS_13, 0x1010101},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_13, 0x8012004},
{OP_WR_E1, QM_REG_QVOQIDX_57, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_57, 0x5},
{OP_WR_E1, QM_REG_QVOQIDX_58, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_58, 0x5},
{OP_WR_E1, QM_REG_QVOQIDX_59, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_59, 0x5},
{OP_WR_E1, QM_REG_QVOQIDX_60, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_60, 0x5},
{OP_WR_E1, QM_REG_WRRWEIGHTS_14, 0x1010101},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_14, 0x20081001},
{OP_WR_E1, QM_REG_QVOQIDX_61, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_61, 0x8},
{OP_WR_E1, QM_REG_QVOQIDX_62, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_62, 0x6},
{OP_WR_E1, QM_REG_QVOQIDX_63, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_63, 0x7},
{OP_WR_E1, QM_REG_WRRWEIGHTS_15, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_64, 0x0},
{OP_WR_E1, QM_REG_VOQQMASK_0_LSB, 0xffff003f},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_15, 0x1010120},
{OP_ZR_E1, QM_REG_VOQQMASK_0_MSB, 0x2},
{OP_ZR_E1H, QM_REG_QVOQIDX_65, 0x4},
{OP_WR_E1, QM_REG_VOQQMASK_1_MSB, 0xffff003f},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_16, 0x1010101},
{OP_WR_E1, QM_REG_VOQQMASK_2_LSB, 0x100},
{OP_WR_E1H, QM_REG_QVOQIDX_69, 0x0},
{OP_WR_E1, QM_REG_VOQQMASK_2_MSB, 0x100},
{OP_WR_E1H, QM_REG_QVOQIDX_70, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_71, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_72, 0x2},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_17, 0x8012004},
{OP_WR_E1H, QM_REG_QVOQIDX_73, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_74, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_75, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_76, 0x5},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_18, 0x20081001},
{OP_WR_E1H, QM_REG_QVOQIDX_77, 0x8},
{OP_WR_E1H, QM_REG_QVOQIDX_78, 0x6},
{OP_WR_E1H, QM_REG_QVOQIDX_79, 0x7},
{OP_WR_E1H, QM_REG_QVOQIDX_80, 0x0},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_19, 0x1010120},
{OP_ZR_E1H, QM_REG_QVOQIDX_81, 0x4},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_20, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_85, 0x0},
{OP_WR_E1H, QM_REG_QVOQIDX_86, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_87, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_88, 0x2},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_21, 0x8012004},
{OP_WR_E1H, QM_REG_QVOQIDX_89, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_90, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_91, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_92, 0x5},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_22, 0x20081001},
{OP_WR_E1H, QM_REG_QVOQIDX_93, 0x8},
{OP_WR_E1H, QM_REG_QVOQIDX_94, 0x6},
{OP_WR_E1H, QM_REG_QVOQIDX_95, 0x7},
{OP_WR_E1H, QM_REG_QVOQIDX_96, 0x1},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_23, 0x1010120},
{OP_WR_E1H, QM_REG_QVOQIDX_97, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_98, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_99, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_100, 0x1},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_24, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_101, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_102, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_103, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_104, 0x2},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_25, 0x8012004},
{OP_WR_E1H, QM_REG_QVOQIDX_105, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_106, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_107, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_108, 0x5},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_26, 0x20081001},
{OP_WR_E1H, QM_REG_QVOQIDX_109, 0x8},
{OP_WR_E1H, QM_REG_QVOQIDX_110, 0x6},
{OP_WR_E1H, QM_REG_QVOQIDX_111, 0x7},
{OP_WR_E1H, QM_REG_QVOQIDX_112, 0x1},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_27, 0x1010120},
{OP_WR_E1H, QM_REG_QVOQIDX_113, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_114, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_115, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_116, 0x1},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_28, 0x1010101},
{OP_WR_E1H, QM_REG_QVOQIDX_117, 0x1},
{OP_WR_E1H, QM_REG_QVOQIDX_118, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_119, 0x4},
{OP_WR_E1H, QM_REG_QVOQIDX_120, 0x2},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_29, 0x8012004},
{OP_WR_E1H, QM_REG_QVOQIDX_121, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_122, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_123, 0x5},
{OP_WR_E1H, QM_REG_QVOQIDX_124, 0x5},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_30, 0x20081001},
{OP_WR_E1H, QM_REG_QVOQIDX_125, 0x8},
{OP_WR_E1H, QM_REG_QVOQIDX_126, 0x6},
{OP_WR_E1H, QM_REG_QVOQIDX_127, 0x7},
{OP_WR_E1H, QM_REG_WRRWEIGHTS_31, 0x1010120},
{OP_WR_E1H, QM_REG_VOQQMASK_0_LSB, 0x3f003f},
{OP_WR_E1H, QM_REG_VOQQMASK_0_MSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_0_LSB_EXT_A, 0x3f003f},
{OP_WR_E1H, QM_REG_VOQQMASK_0_MSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_1_LSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_1_MSB, 0x3f003f},
{OP_WR_E1H, QM_REG_VOQQMASK_1_LSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_1_MSB_EXT_A, 0x3f003f},
{OP_WR_E1H, QM_REG_VOQQMASK_2_LSB, 0x1000100},
{OP_WR_E1H, QM_REG_VOQQMASK_2_MSB, 0x1000100},
{OP_WR_E1H, QM_REG_VOQQMASK_2_LSB_EXT_A, 0x1000100},
{OP_WR_E1H, QM_REG_VOQQMASK_2_MSB_EXT_A, 0x1000100},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, QM_REG_VOQQMASK_3_LSB, 0x2},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_VOQQMASK_4_LSB, 0xc0},
{OP_WR_E1H, QM_REG_VOQQMASK_3_LSB_EXT_A, 0x0},
{OP_WR_E1, QM_REG_VOQQMASK_4_MSB, 0xc0},
{OP_WR_E1H, QM_REG_VOQQMASK_3_MSB_EXT_A, 0x0},
{OP_WR_E1, QM_REG_VOQQMASK_5_LSB, 0x1e00},
{OP_WR_E1H, QM_REG_VOQQMASK_4_LSB, 0xc000c0},
{OP_WR_E1, QM_REG_VOQQMASK_5_MSB, 0x1e00},
{OP_WR_E1H, QM_REG_VOQQMASK_4_MSB, 0xc000c0},
{OP_WR_E1, QM_REG_VOQQMASK_6_LSB, 0x4000},
{OP_WR_E1H, QM_REG_VOQQMASK_4_LSB_EXT_A, 0xc000c0},
{OP_WR_E1, QM_REG_VOQQMASK_6_MSB, 0x4000},
{OP_WR_E1H, QM_REG_VOQQMASK_4_MSB_EXT_A, 0xc000c0},
{OP_WR_E1, QM_REG_VOQQMASK_7_LSB, 0x8000},
{OP_WR_E1H, QM_REG_VOQQMASK_5_LSB, 0x1e001e00},
{OP_WR_E1, QM_REG_VOQQMASK_7_MSB, 0x8000},
{OP_WR_E1H, QM_REG_VOQQMASK_5_MSB, 0x1e001e00},
{OP_WR_E1, QM_REG_VOQQMASK_8_LSB, 0x2000},
{OP_WR_E1H, QM_REG_VOQQMASK_5_LSB_EXT_A, 0x1e001e00},
{OP_WR_E1, QM_REG_VOQQMASK_8_MSB, 0x2000},
{OP_WR_E1H, QM_REG_VOQQMASK_5_MSB_EXT_A, 0x1e001e00},
{OP_ZR_E1, QM_REG_VOQQMASK_9_LSB, 0x7},
{OP_WR_E1H, QM_REG_VOQQMASK_6_LSB, 0x40004000},
{OP_WR_E1H, QM_REG_VOQQMASK_6_MSB, 0x40004000},
{OP_WR_E1H, QM_REG_VOQQMASK_6_LSB_EXT_A, 0x40004000},
{OP_WR_E1H, QM_REG_VOQQMASK_6_MSB_EXT_A, 0x40004000},
{OP_WR_E1H, QM_REG_VOQQMASK_7_LSB, 0x80008000},
{OP_WR_E1H, QM_REG_VOQQMASK_7_MSB, 0x80008000},
{OP_WR_E1H, QM_REG_VOQQMASK_7_LSB_EXT_A, 0x80008000},
{OP_WR_E1H, QM_REG_VOQQMASK_7_MSB_EXT_A, 0x80008000},
{OP_WR_E1H, QM_REG_VOQQMASK_8_LSB, 0x20002000},
{OP_WR_E1H, QM_REG_VOQQMASK_8_MSB, 0x20002000},
{OP_WR_E1H, QM_REG_VOQQMASK_8_LSB_EXT_A, 0x20002000},
{OP_WR_E1H, QM_REG_VOQQMASK_8_MSB_EXT_A, 0x20002000},
{OP_ZR_E1H, QM_REG_VOQQMASK_9_LSB, 0x2},
{OP_WR_E1H, QM_REG_VOQQMASK_9_LSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_9_MSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_10_LSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_10_MSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_10_LSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_10_MSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_11_LSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_11_MSB, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_11_LSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQQMASK_11_MSB_EXT_A, 0x0},
{OP_WR_E1H, QM_REG_VOQPORT_0, 0x0},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_VOQPORT_1, 0x1},
{OP_ZR, QM_REG_VOQPORT_2, 0xa},
{OP_WR, QM_REG_CMINTVOQMASK_0, 0xc08},
{OP_WR, QM_REG_CMINTVOQMASK_1, 0x40},
{OP_WR, QM_REG_CMINTVOQMASK_2, 0x100},
{OP_WR, QM_REG_CMINTVOQMASK_3, 0x20},
{OP_WR, QM_REG_CMINTVOQMASK_4, 0x17},
{OP_WR, QM_REG_CMINTVOQMASK_5, 0x80},
{OP_WR, QM_REG_CMINTVOQMASK_6, 0x200},
{OP_WR, QM_REG_CMINTVOQMASK_7, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_HWAEMPTYMASK_LSB, 0xffff01ff},
{OP_WR_E1H, QM_REG_HWAEMPTYMASK_LSB, 0x1ff01ff},
{OP_WR_E1, QM_REG_HWAEMPTYMASK_MSB, 0xffff01ff},
{OP_WR_E1H, QM_REG_HWAEMPTYMASK_MSB, 0x1ff01ff},
{OP_WR_E1H, QM_REG_HWAEMPTYMASK_LSB_EXT_A, 0x1ff01ff},
{OP_WR_E1H, QM_REG_HWAEMPTYMASK_MSB_EXT_A, 0x1ff01ff},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_ENBYPVOQMASK, 0x13},
{OP_WR, QM_REG_VOQCREDITAFULLTHR, 0x13f},
{OP_WR, QM_REG_VOQINITCREDIT_0, 0x140},
{OP_WR, QM_REG_VOQINITCREDIT_1, 0x140},
{OP_ZR, QM_REG_VOQINITCREDIT_2, 0x2},
{OP_WR, QM_REG_VOQINITCREDIT_4, 0xc0},
{OP_ZR, QM_REG_VOQINITCREDIT_5, 0x7},
{OP_WR, QM_REG_TASKCRDCOST_0, 0x48},
{OP_WR, QM_REG_TASKCRDCOST_1, 0x48},
{OP_ZR, QM_REG_TASKCRDCOST_2, 0x2},
{OP_WR, QM_REG_TASKCRDCOST_4, 0x48},
{OP_ZR, QM_REG_TASKCRDCOST_5, 0x7},
{OP_WR, QM_REG_BYTECRDINITVAL, 0x8000},
{OP_WR, QM_REG_BYTECRDCOST, 0x25e4},
{OP_WR, QM_REG_BYTECREDITAFULLTHR, 0x7fff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_ENBYTECRD_LSB, 0x7},
{OP_WR_E1H, QM_REG_ENBYTECRD_LSB, 0x70007},
{OP_WR_E1, QM_REG_ENBYTECRD_MSB, 0x7},
{OP_WR_E1H, QM_REG_ENBYTECRD_MSB, 0x70007},
{OP_WR_E1H, QM_REG_ENBYTECRD_LSB_EXT_A, 0x70007},
{OP_WR_E1H, QM_REG_ENBYTECRD_MSB_EXT_A, 0x70007},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_BYTECRDPORT_LSB, 0x0},
{OP_WR, QM_REG_BYTECRDPORT_MSB, 0xffffffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, QM_REG_FUNCNUMSEL_LSB, 0x0},
{OP_WR_E1H, QM_REG_BYTECRDPORT_LSB_EXT_A, 0x0},
{OP_WR_E1, QM_REG_FUNCNUMSEL_MSB, 0xffffffff},
{OP_WR_E1H, QM_REG_BYTECRDPORT_MSB_EXT_A, 0xffffffff},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_0, 0x0},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_1, 0x2},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_2, 0x1},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_3, 0x3},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_4, 0x4},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_5, 0x6},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_6, 0x5},
{OP_WR_E1H, QM_REG_PQ2PCIFUNC_7, 0x7},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, QM_REG_CMINTEN, 0xff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define QM_COMMON_END 1400
#define PBF_COMMON_START 1400
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PBF_REG_INIT, 0x1},
{OP_WR, PBF_REG_INIT_P4, 0x1},
{OP_WR, PBF_REG_MAC_LB_ENABLE, 0x1},
{OP_WR, PBF_REG_IF_ENABLE_REG, 0x7fff},
{OP_WR, PBF_REG_INIT_P4, 0x0},
{OP_WR, PBF_REG_INIT, 0x0},
{OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P4, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define PBF_COMMON_END 1407
#define PBF_PORT0_START 1407
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PBF_REG_INIT_P0, 0x1},
{OP_WR, PBF_REG_MAC_IF0_ENABLE, 0x1},
{OP_WR, PBF_REG_INIT_P0, 0x0},
{OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P0, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define PBF_PORT0_END 1411
#define PBF_PORT1_START 1411
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PBF_REG_INIT_P1, 0x1},
{OP_WR, PBF_REG_MAC_IF1_ENABLE, 0x1},
{OP_WR, PBF_REG_INIT_P1, 0x0},
{OP_WR, PBF_REG_DISABLE_NEW_TASK_PROC_P1, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define PBF_PORT1_END 1415
#define XCM_COMMON_START 1415
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XCM_REG_XX_OVFL_EVNT_ID, 0x32},
{OP_WR, XCM_REG_XQM_XCM_HDR_P, 0x3150020},
{OP_WR, XCM_REG_XQM_XCM_HDR_S, 0x3150020},
{OP_WR, XCM_REG_TM_XCM_HDR, 0x1000030},
{OP_WR, XCM_REG_ERR_XCM_HDR, 0x8100000},
{OP_WR, XCM_REG_ERR_EVNT_ID, 0x33},
{OP_WR, XCM_REG_EXPR_EVNT_ID, 0x30},
{OP_WR, XCM_REG_STOP_EVNT_ID, 0x31},
{OP_WR, XCM_REG_STORM_WEIGHT, 0x2},
{OP_WR, XCM_REG_TSEM_WEIGHT, 0x5},
{OP_WR, XCM_REG_CSEM_WEIGHT, 0x2},
{OP_WR, XCM_REG_USEM_WEIGHT, 0x2},
{OP_WR, XCM_REG_PBF_WEIGHT, 0x7},
{OP_WR, XCM_REG_NIG1_WEIGHT, 0x1},
{OP_WR, XCM_REG_CP_WEIGHT, 0x0},
{OP_WR, XCM_REG_XSDM_WEIGHT, 0x5},
{OP_WR, XCM_REG_XQM_P_WEIGHT, 0x3},
{OP_WR, XCM_REG_XCM_XQM_USE_Q, 0x1},
{OP_WR, XCM_REG_XQM_BYP_ACT_UPD, 0x6},
{OP_WR, XCM_REG_UNA_GT_NXT_Q, 0x0},
{OP_WR, XCM_REG_AUX1_Q, 0x2},
{OP_WR, XCM_REG_AUX_CNT_FLG_Q_19, 0x1},
{OP_WR, XCM_REG_GR_ARB_TYPE, 0x1},
{OP_WR, XCM_REG_GR_LD0_PR, 0x1},
{OP_WR, XCM_REG_GR_LD1_PR, 0x2},
{OP_WR, XCM_REG_CFC_INIT_CRD, 0x1},
{OP_WR, XCM_REG_FIC0_INIT_CRD, 0x40},
{OP_WR, XCM_REG_FIC1_INIT_CRD, 0x40},
{OP_WR, XCM_REG_TM_INIT_CRD, 0x4},
{OP_WR, XCM_REG_XQM_INIT_CRD, 0x20},
{OP_WR, XCM_REG_XX_INIT_CRD, 0x2},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, XCM_REG_XX_MSG_NUM, 0x1f},
{OP_WR_E1H, XCM_REG_XX_MSG_NUM, 0x20},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, XCM_REG_XX_TABLE, 0x12},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, XCM_REG_XX_DESCR_TABLE, 0x1f02ce},
{OP_SW_E1H, XCM_REG_XX_DESCR_TABLE, 0x1f0302},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XCM_REG_N_SM_CTX_LD_0, 0xf},
{OP_WR, XCM_REG_N_SM_CTX_LD_1, 0x7},
{OP_WR, XCM_REG_N_SM_CTX_LD_2, 0xb},
{OP_WR, XCM_REG_N_SM_CTX_LD_3, 0xe},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, XCM_REG_N_SM_CTX_LD_4, 0x4},
{OP_WR_E1H, XCM_REG_N_SM_CTX_LD_4, 0xc},
{OP_ZR_E1H, XCM_REG_N_SM_CTX_LD_5, 0x3},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XCM_REG_XCM_REG0_SZ, 0x4},
{OP_WR, XCM_REG_XCM_STORM0_IFEN, 0x1},
{OP_WR, XCM_REG_XCM_STORM1_IFEN, 0x1},
{OP_WR, XCM_REG_XCM_XQM_IFEN, 0x1},
{OP_WR, XCM_REG_STORM_XCM_IFEN, 0x1},
{OP_WR, XCM_REG_XQM_XCM_IFEN, 0x1},
{OP_WR, XCM_REG_XSDM_IFEN, 0x1},
{OP_WR, XCM_REG_TM_XCM_IFEN, 0x1},
{OP_WR, XCM_REG_XCM_TM_IFEN, 0x1},
{OP_WR, XCM_REG_TSEM_IFEN, 0x1},
{OP_WR, XCM_REG_CSEM_IFEN, 0x1},
{OP_WR, XCM_REG_USEM_IFEN, 0x1},
{OP_WR, XCM_REG_DORQ_IFEN, 0x1},
{OP_WR, XCM_REG_PBF_IFEN, 0x1},
{OP_WR, XCM_REG_NIG0_IFEN, 0x1},
{OP_WR, XCM_REG_NIG1_IFEN, 0x1},
{OP_WR, XCM_REG_CDU_AG_WR_IFEN, 0x1},
{OP_WR, XCM_REG_CDU_AG_RD_IFEN, 0x1},
{OP_WR, XCM_REG_CDU_SM_WR_IFEN, 0x1},
{OP_WR, XCM_REG_CDU_SM_RD_IFEN, 0x1},
{OP_WR, XCM_REG_XCM_CFC_IFEN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define XCM_COMMON_END 1479
#define XCM_PORT0_START 1479
{OP_WR_E1, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8},
{OP_WR_E1, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0},
{OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10, 0x0},
{OP_WR_E1, XCM_REG_WU_DA_CNT_CMD00, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_CNT_CMD10, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff},
{OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff},
#define XCM_PORT0_END 1487
#define XCM_PORT1_START 1487
{OP_WR_E1, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8},
{OP_WR_E1, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0},
{OP_WR_E1, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11, 0x0},
{OP_WR_E1, XCM_REG_WU_DA_CNT_CMD01, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_CNT_CMD11, 0x2},
{OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff},
{OP_WR_E1, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff},
#define XCM_PORT1_END 1495
#define XCM_FUNC0_START 1495
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD00, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD10, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0},
#define XCM_FUNC0_END 1504
#define XCM_FUNC1_START 1504
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD01, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD11, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0},
#define XCM_FUNC1_END 1513
#define XCM_FUNC2_START 1513
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD00, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD10, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0},
#define XCM_FUNC2_END 1522
#define XCM_FUNC3_START 1522
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD01, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD11, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0},
#define XCM_FUNC3_END 1531
#define XCM_FUNC4_START 1531
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD00, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD10, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0},
#define XCM_FUNC4_END 1540
#define XCM_FUNC5_START 1540
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD01, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD11, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0},
#define XCM_FUNC5_END 1549
#define XCM_FUNC6_START 1549
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_0, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD00, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD10, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL00, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL10, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_0, 0x0},
#define XCM_FUNC6_END 1558
#define XCM_FUNC7_START 1558
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_TMR_VAL_1, 0xc8},
{OP_WR_E1H, XCM_REG_GLB_DEL_ACK_MAX_CNT_1, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11, 0x0},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD01, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_CMD11, 0x2},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL01, 0xff},
{OP_WR_E1H, XCM_REG_WU_DA_CNT_UPD_VAL11, 0xff},
{OP_WR_E1H, XCM_REG_PHYS_QNUM3_1, 0x0},
#define XCM_FUNC7_END 1567
#define XSEM_COMMON_START 1567
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_RD, XSEM_REG_MSG_NUM_FIC0, 0x0},
{OP_RD, XSEM_REG_MSG_NUM_FIC1, 0x0},
{OP_RD, XSEM_REG_MSG_NUM_FOC0, 0x0},
{OP_RD, XSEM_REG_MSG_NUM_FOC1, 0x0},
{OP_RD, XSEM_REG_MSG_NUM_FOC2, 0x0},
{OP_RD, XSEM_REG_MSG_NUM_FOC3, 0x0},
{OP_WR, XSEM_REG_ARB_ELEMENT0, 0x1},
{OP_WR, XSEM_REG_ARB_ELEMENT1, 0x2},
{OP_WR, XSEM_REG_ARB_ELEMENT2, 0x3},
{OP_WR, XSEM_REG_ARB_ELEMENT3, 0x0},
{OP_WR, XSEM_REG_ARB_ELEMENT4, 0x4},
{OP_WR, XSEM_REG_ARB_CYCLE_SIZE, 0x1},
{OP_WR, XSEM_REG_TS_0_AS, 0x0},
{OP_WR, XSEM_REG_TS_1_AS, 0x1},
{OP_WR, XSEM_REG_TS_2_AS, 0x4},
{OP_WR, XSEM_REG_TS_3_AS, 0x0},
{OP_WR, XSEM_REG_TS_4_AS, 0x1},
{OP_WR, XSEM_REG_TS_5_AS, 0x3},
{OP_WR, XSEM_REG_TS_6_AS, 0x0},
{OP_WR, XSEM_REG_TS_7_AS, 0x1},
{OP_WR, XSEM_REG_TS_8_AS, 0x4},
{OP_WR, XSEM_REG_TS_9_AS, 0x0},
{OP_WR, XSEM_REG_TS_10_AS, 0x1},
{OP_WR, XSEM_REG_TS_11_AS, 0x3},
{OP_WR, XSEM_REG_TS_12_AS, 0x0},
{OP_WR, XSEM_REG_TS_13_AS, 0x1},
{OP_WR, XSEM_REG_TS_14_AS, 0x4},
{OP_WR, XSEM_REG_TS_15_AS, 0x0},
{OP_WR, XSEM_REG_TS_16_AS, 0x4},
{OP_WR, XSEM_REG_TS_17_AS, 0x3},
{OP_ZR, XSEM_REG_TS_18_AS, 0x2},
{OP_WR, XSEM_REG_ENABLE_IN, 0x3fff},
{OP_WR, XSEM_REG_ENABLE_OUT, 0x3ff},
{OP_WR, XSEM_REG_FIC0_DISABLE, 0x0},
{OP_WR, XSEM_REG_FIC1_DISABLE, 0x0},
{OP_WR, XSEM_REG_PAS_DISABLE, 0x0},
{OP_WR, XSEM_REG_THREADS_LIST, 0xffff},
{OP_ZR, XSEM_REG_PASSIVE_BUFFER, 0x800},
{OP_WR, XSEM_REG_FAST_MEMORY + 0x18bc0, 0x1},
{OP_WR, XSEM_REG_FAST_MEMORY + 0x18000, 0x0},
{OP_WR, XSEM_REG_FAST_MEMORY + 0x18040, 0x18},
{OP_WR, XSEM_REG_FAST_MEMORY + 0x18080, 0xc},
{OP_WR, XSEM_REG_FAST_MEMORY + 0x180c0, 0x66},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_ASIC, XSEM_REG_FAST_MEMORY + 0x18300, 0x7a120},
{OP_WR_EMUL, XSEM_REG_FAST_MEMORY + 0x18300, 0x138},
{OP_WR_FPGA, XSEM_REG_FAST_MEMORY + 0x18300, 0x1388},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSEM_REG_FAST_MEMORY + 0x183c0, 0x1f4},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_ASIC, XSEM_REG_FAST_MEMORY + 0x18340, 0x1f4},
{OP_WR_EMUL, XSEM_REG_FAST_MEMORY + 0x18340, 0x0},
{OP_WR_FPGA, XSEM_REG_FAST_MEMORY + 0x18340, 0x5},
{OP_WR_EMUL, XSEM_REG_FAST_MEMORY + 0x18380, 0x4c4b4},
{OP_WR_ASIC, XSEM_REG_FAST_MEMORY + 0x18380, 0x1dcd6500},
{OP_WR_EMUL_E1H, XSEM_REG_FAST_MEMORY + 0x11480, 0x0},
{OP_WR_FPGA, XSEM_REG_FAST_MEMORY + 0x18380, 0x4c4b40},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3d00, 0x4},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x11480, 0x1},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3000, 0x48},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x28a8, 0x4},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1020, 0xc8},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2080, 0x48},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1000, 0x2},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x9020, 0xc8},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3128, 0x8e},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x9000, 0x2},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3368, 0x0},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x21a8, 0x86},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3370, 0x202ed},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2000, 0x20},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3b90, 0x402ef},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x23c8, 0x0},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1518, 0x1},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x23d0, 0x20321},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1830, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2498, 0x40323},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1838, 0x0},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x2ac8, 0x0},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1820, 0x202f3},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x2ab8, 0x0},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4ac0, 0x2},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x3010, 0x1},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4b00, 0x4},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x4040, 0x10},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x1f50, 0x202f5},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x4000, 0x100327},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6ac0, 0x2},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6b00, 0x4},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x83b0, 0x20337},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x0},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c00, 0x1002f7},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c00, 0x100339},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x1000000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c40, 0x80307},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c40, 0x80349},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, XSEM_REG_FAST_MEMORY + 0x10800, 0x2000000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x10c60, 0x8030f},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x10c60, 0x80351},
{OP_ZP_E1, XSEM_REG_INT_TABLE, 0xab0000},
{OP_ZP_E1H, XSEM_REG_INT_TABLE, 0xac0000},
{OP_WR_64_E1, XSEM_REG_INT_TABLE + 0x368, 0x130317},
{OP_WR_64_E1H, XSEM_REG_INT_TABLE + 0x368, 0x130359},
{OP_ZP_E1, XSEM_REG_PRAM, 0xc09e0000},
{OP_ZP_E1H, XSEM_REG_PRAM, 0xc3b20000},
{OP_WR_64_E1, XSEM_REG_PRAM + 0x1c0c0, 0x47e80319},
{OP_WR_64_E1H, XSEM_REG_PRAM + 0x1c8c0, 0x46e8035b},
#define XSEM_COMMON_END 1671
#define XSEM_PORT0_START 1671
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3ba0, 0x10},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xc000, 0xfc},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3c20, 0x1c},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x24a8, 0x10},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1400, 0xa},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2528, 0x1c},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1450, 0x6},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2608, 0x1c},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3378, 0xfc},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x26e8, 0x1c},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3b58, 0x0},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x27c8, 0x1c},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d10, 0x10031b},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa000, 0x28},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1500, 0x0},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa140, 0xc},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1508, 0x1},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x3000, 0x1},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5020, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5030, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5000, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5010, 0x2},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x5040, 0x0},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x5208, 0x1},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x5048, 0xe},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x6ac8, 0x2035d},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x50b8, 0x1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6b10, 0x42},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ac8, 0x2032b},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6d20, 0x4},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4b10, 0x42},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4d20, 0x4},
#define XSEM_PORT0_END 1703
#define XSEM_PORT1_START 1703
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3be0, 0x10},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xc3f0, 0xfc},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3c90, 0x1c},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x24e8, 0x10},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1428, 0xa},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2598, 0x1c},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x1468, 0x6},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2678, 0x1c},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x3768, 0xfc},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2758, 0x1c},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x3b5c, 0x0},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x2838, 0x1c},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x3d50, 0x10032d},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa0a0, 0x28},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x1504, 0x0},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0xa170, 0xc},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x150c, 0x1},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x3004, 0x1},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5028, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5038, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5008, 0x2},
{OP_ZR, XSEM_REG_FAST_MEMORY + 0x5018, 0x2},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x5044, 0x0},
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0x520c, 0x1},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x5080, 0xe},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x6ad0, 0x2035f},
{OP_WR_E1, XSEM_REG_FAST_MEMORY + 0x50bc, 0x1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6c18, 0x42},
{OP_SW_E1, XSEM_REG_FAST_MEMORY + 0x4ad0, 0x2033d},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x6d30, 0x4},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4c18, 0x42},
{OP_ZR_E1, XSEM_REG_FAST_MEMORY + 0x4d30, 0x4},
#define XSEM_PORT1_END 1735
#define XSEM_FUNC0_START 1735
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e0, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x28b8, 0x100361},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5048, 0xe},
#define XSEM_FUNC0_END 1738
#define XSEM_FUNC1_START 1738
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e4, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x28f8, 0x100371},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5080, 0xe},
#define XSEM_FUNC1_END 1741
#define XSEM_FUNC2_START 1741
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7e8, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2938, 0x100381},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x50b8, 0xe},
#define XSEM_FUNC2_END 1744
#define XSEM_FUNC3_START 1744
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7ec, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2978, 0x100391},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x50f0, 0xe},
#define XSEM_FUNC3_END 1747
#define XSEM_FUNC4_START 1747
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f0, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x29b8, 0x1003a1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5128, 0xe},
#define XSEM_FUNC4_END 1750
#define XSEM_FUNC5_START 1750
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f4, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x29f8, 0x1003b1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5160, 0xe},
#define XSEM_FUNC5_END 1753
#define XSEM_FUNC6_START 1753
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7f8, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2a38, 0x1003c1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x5198, 0xe},
#define XSEM_FUNC6_END 1756
#define XSEM_FUNC7_START 1756
{OP_WR_E1H, XSEM_REG_FAST_MEMORY + 0xc7fc, 0x0},
{OP_SW_E1H, XSEM_REG_FAST_MEMORY + 0x2a78, 0x1003d1},
{OP_ZR_E1H, XSEM_REG_FAST_MEMORY + 0x51d0, 0xe},
#define XSEM_FUNC7_END 1759
#define CDU_COMMON_START 1759
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CDU_REG_CDU_CONTROL0, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, CDU_REG_MF_MODE, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CDU_REG_CDU_CHK_MASK0, 0x3d000},
{OP_WR, CDU_REG_CDU_CHK_MASK1, 0x3d},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WB_E1, CDU_REG_L1TT, 0x200033f},
{OP_WB_E1H, CDU_REG_L1TT, 0x20003e1},
{OP_WB_E1, CDU_REG_MATT, 0x20053f},
{OP_WB_E1H, CDU_REG_MATT, 0x2805e1},
{OP_ZR_E1, CDU_REG_MATT + 0x80, 0x2},
{OP_WB_E1, CDU_REG_MATT + 0x88, 0x6055f},
{OP_ZR, CDU_REG_MATT + 0xa0, 0x18},
#define CDU_COMMON_END 1770
#define DMAE_COMMON_START 1770
{OP_ZR, DMAE_REG_CMD_MEM, 0xe0},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, DMAE_REG_CRC16C_INIT, 0x0},
{OP_WR, DMAE_REG_CRC16T10_INIT, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, DMAE_REG_PXP_REQ_INIT_CRD, 0x1},
{OP_WR_E1H, DMAE_REG_PXP_REQ_INIT_CRD, 0x2},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, DMAE_REG_PCI_IFEN, 0x1},
{OP_WR, DMAE_REG_GRC_IFEN, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define DMAE_COMMON_END 1777
#define PXP_COMMON_START 1777
{OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x400, 0x50565},
{OP_WB_E1H, PXP_REG_HST_INBOUND_INT + 0x400, 0x50609},
{OP_WB_E1, PXP_REG_HST_INBOUND_INT + 0x420, 0x5056a},
{OP_WB_E1H, PXP_REG_HST_INBOUND_INT, 0x5060e},
{OP_WB_E1, PXP_REG_HST_INBOUND_INT, 0x5056f},
#define PXP_COMMON_END 1782
#define CFC_COMMON_START 1782
{OP_ZR_E1H, CFC_REG_LINK_LIST, 0x100},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, CFC_REG_CONTROL0, 0x10},
{OP_WR, CFC_REG_DISABLE_ON_ERROR, 0x3fff},
{OP_WR, CFC_REG_LCREQ_WEIGHTS, 0x84924a},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define CFC_COMMON_END 1786
#define HC_COMMON_START 1786
{OP_ZR_E1, HC_REG_USTORM_ADDR_FOR_COALESCE, 0x4},
#define HC_COMMON_END 1787
#define HC_PORT0_START 1787
{OP_WR_E1, HC_REG_CONFIG_0, 0x1080},
{OP_ZR_E1, HC_REG_UC_RAM_ADDR_0, 0x2},
{OP_WR_E1, HC_REG_ATTN_NUM_P0, 0x10},
{OP_WR_E1, HC_REG_LEADING_EDGE_0, 0xffff},
{OP_WR_E1, HC_REG_TRAILING_EDGE_0, 0xffff},
{OP_WR_E1, HC_REG_AGG_INT_0, 0x0},
{OP_WR_E1, HC_REG_ATTN_IDX, 0x0},
{OP_ZR_E1, HC_REG_ATTN_BIT, 0x2},
{OP_WR_E1, HC_REG_VQID_0, 0x2b5},
{OP_WR_E1, HC_REG_PCI_CONFIG_0, 0x0},
{OP_ZR_E1, HC_REG_P0_PROD_CONS, 0x4a},
{OP_WR_E1, HC_REG_INT_MASK, 0x1ffff},
{OP_ZR_E1, HC_REG_PBA_COMMAND, 0x2},
{OP_WR_E1, HC_REG_CONFIG_0, 0x1a80},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS, 0x24},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a},
{OP_ZR_E1, HC_REG_PBA_COMMAND, 0x2},
#define HC_PORT0_END 1806
#define HC_PORT1_START 1806
{OP_WR_E1, HC_REG_CONFIG_1, 0x1080},
{OP_ZR_E1, HC_REG_UC_RAM_ADDR_1, 0x2},
{OP_WR_E1, HC_REG_ATTN_NUM_P1, 0x10},
{OP_WR_E1, HC_REG_LEADING_EDGE_1, 0xffff},
{OP_WR_E1, HC_REG_TRAILING_EDGE_1, 0xffff},
{OP_WR_E1, HC_REG_AGG_INT_1, 0x0},
{OP_WR_E1, HC_REG_ATTN_IDX + 0x4, 0x0},
{OP_ZR_E1, HC_REG_ATTN_BIT + 0x8, 0x2},
{OP_WR_E1, HC_REG_VQID_1, 0x2b5},
{OP_WR_E1, HC_REG_PCI_CONFIG_1, 0x0},
{OP_ZR_E1, HC_REG_P1_PROD_CONS, 0x4a},
{OP_WR_E1, HC_REG_INT_MASK + 0x4, 0x1ffff},
{OP_ZR_E1, HC_REG_PBA_COMMAND + 0x8, 0x2},
{OP_WR_E1, HC_REG_CONFIG_1, 0x1a80},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x90, 0x24},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a},
{OP_ZR_E1, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a},
{OP_ZR_E1, HC_REG_PBA_COMMAND + 0x8, 0x2},
#define HC_PORT1_END 1825
#define HC_FUNC0_START 1825
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x0},
{OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT, 0x2},
{OP_WR_E1H, HC_REG_VQID_0, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_0, 0x0},
{OP_ZR_E1H, HC_REG_P0_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a},
#define HC_FUNC0_END 1840
#define HC_FUNC1_START 1840
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x1},
{OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX + 0x4, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT + 0x8, 0x2},
{OP_WR_E1H, HC_REG_VQID_1, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_1, 0x0},
{OP_ZR_E1H, HC_REG_P1_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK + 0x4, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND + 0x8, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x90, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a},
#define HC_FUNC1_END 1855
#define HC_FUNC2_START 1855
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x2},
{OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT, 0x2},
{OP_WR_E1H, HC_REG_VQID_0, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_0, 0x0},
{OP_ZR_E1H, HC_REG_P0_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a},
#define HC_FUNC2_END 1870
#define HC_FUNC3_START 1870
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x3},
{OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX + 0x4, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT + 0x8, 0x2},
{OP_WR_E1H, HC_REG_VQID_1, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_1, 0x0},
{OP_ZR_E1H, HC_REG_P1_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK + 0x4, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND + 0x8, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x90, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a},
#define HC_FUNC3_END 1885
#define HC_FUNC4_START 1885
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x4},
{OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT, 0x2},
{OP_WR_E1H, HC_REG_VQID_0, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_0, 0x0},
{OP_ZR_E1H, HC_REG_P0_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a},
#define HC_FUNC4_END 1900
#define HC_FUNC5_START 1900
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x5},
{OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX + 0x4, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT + 0x8, 0x2},
{OP_WR_E1H, HC_REG_VQID_1, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_1, 0x0},
{OP_ZR_E1H, HC_REG_P1_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK + 0x4, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND + 0x8, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x90, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a},
#define HC_FUNC5_END 1915
#define HC_FUNC6_START 1915
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P0, 0x6},
{OP_WR_E1H, HC_REG_ATTN_NUM_P0, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT, 0x2},
{OP_WR_E1H, HC_REG_VQID_0, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_0, 0x0},
{OP_ZR_E1H, HC_REG_P0_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_0, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x120, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x370, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x5c0, 0x4a},
#define HC_FUNC6_END 1930
#define HC_FUNC7_START 1930
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1080},
{OP_WR_E1H, HC_REG_FUNC_NUM_P1, 0x7},
{OP_WR_E1H, HC_REG_ATTN_NUM_P1, 0x10},
{OP_WR_E1H, HC_REG_ATTN_IDX + 0x4, 0x0},
{OP_ZR_E1H, HC_REG_ATTN_BIT + 0x8, 0x2},
{OP_WR_E1H, HC_REG_VQID_1, 0x2b5},
{OP_WR_E1H, HC_REG_PCI_CONFIG_1, 0x0},
{OP_ZR_E1H, HC_REG_P1_PROD_CONS, 0x4a},
{OP_WR_E1H, HC_REG_INT_MASK + 0x4, 0x1ffff},
{OP_ZR_E1H, HC_REG_PBA_COMMAND + 0x8, 0x2},
{OP_WR_E1H, HC_REG_CONFIG_1, 0x1a80},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x90, 0x24},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x248, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x498, 0x4a},
{OP_ZR_E1H, HC_REG_STATISTIC_COUNTERS + 0x6e8, 0x4a},
#define HC_FUNC7_END 1945
#define PXP2_COMMON_START 1945
{OP_WR_E1, PXP2_REG_PGL_CONTROL0, 0xe38340},
{OP_WR_E1H, PXP2_REG_RQ_DRAM_ALIGN, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_PGL_CONTROL1, 0x3c10},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, PXP2_REG_RQ_ELT_DISABLE, 0x1},
{OP_WR_E1H, PXP2_REG_WR_REV_MODE, 0x0},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_PGL_INT_TSDM_0, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_1, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_2, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_3, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_4, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_5, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_6, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_TSDM_7, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_1, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_2, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_3, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_4, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_5, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_6, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_USDM_7, 0xffffffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, PXP2_REG_PGL_INT_XSDM_1, 0xffffffff},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_PGL_INT_XSDM_2, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_XSDM_3, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_XSDM_4, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_XSDM_5, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_XSDM_6, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_XSDM_7, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_0, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_1, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_2, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_3, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_4, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_5, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_6, 0xffffffff},
{OP_WR, PXP2_REG_PGL_INT_CSDM_7, 0xffffffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, PXP2_REG_PGL_INT_XSDM_0, 0xffff3330},
{OP_WR_E1H, PXP2_REG_PGL_INT_XSDM_0, 0xff802000},
{OP_WR_E1, PXP2_REG_PGL_INT_XSDM_1, 0xffff3340},
{OP_WR_E1H, PXP2_REG_PGL_INT_USDM_0, 0xf0005000},
{OP_WR_E1, PXP2_REG_PGL_INT_USDM_0, 0xf0003000},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ6, 0x8},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ9, 0x8},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ10, 0x8},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ11, 0x2},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ17, 0x4},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ18, 0x5},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ19, 0x4},
{OP_WR, PXP2_REG_RD_MAX_BLKS_VQ22, 0x0},
{OP_WR, PXP2_REG_RD_START_INIT, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR, PXP2_REG_WR_DMAE_TH, 0x3f},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_RQ_BW_RD_ADD0, 0x40},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD1, 0x1808},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD2, 0x803},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD3, 0x803},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD4, 0x40},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD5, 0x3},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD6, 0x803},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD7, 0x803},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD8, 0x803},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD9, 0x10003},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD10, 0x803},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD11, 0x803},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD12, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD13, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD14, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD15, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD16, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD17, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD18, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD19, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD20, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD22, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD23, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD24, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD25, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD26, 0x3},
{OP_WR, PXP2_REG_RQ_BW_RD_ADD27, 0x3},
{OP_WR, PXP2_REG_PSWRQ_BW_ADD28, 0x2403},
{OP_WR, PXP2_REG_RQ_BW_WR_ADD29, 0x2f},
{OP_WR, PXP2_REG_RQ_BW_WR_ADD30, 0x9},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND0, 0x19},
{OP_WR, PXP2_REG_PSWRQ_BW_UB1, 0x184},
{OP_WR, PXP2_REG_PSWRQ_BW_UB2, 0x183},
{OP_WR, PXP2_REG_PSWRQ_BW_UB3, 0x306},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND4, 0x19},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND5, 0x6},
{OP_WR, PXP2_REG_PSWRQ_BW_UB6, 0x306},
{OP_WR, PXP2_REG_PSWRQ_BW_UB7, 0x306},
{OP_WR, PXP2_REG_PSWRQ_BW_UB8, 0x306},
{OP_WR, PXP2_REG_PSWRQ_BW_UB9, 0xc86},
{OP_WR, PXP2_REG_PSWRQ_BW_UB10, 0x306},
{OP_WR, PXP2_REG_PSWRQ_BW_UB11, 0x306},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND12, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND13, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND14, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND15, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND16, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND17, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND18, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND19, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND20, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND22, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND23, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND24, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND25, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND26, 0x6},
{OP_WR, PXP2_REG_RQ_BW_RD_UBOUND27, 0x6},
{OP_WR, PXP2_REG_PSWRQ_BW_UB28, 0x306},
{OP_WR, PXP2_REG_RQ_BW_WR_UBOUND29, 0x13},
{OP_WR, PXP2_REG_RQ_BW_WR_UBOUND30, 0x6},
{OP_WR, PXP2_REG_PSWRQ_BW_L1, 0x1004},
{OP_WR, PXP2_REG_PSWRQ_BW_L2, 0x1004},
{OP_WR, PXP2_REG_PSWRQ_BW_RD, 0x106440},
{OP_WR, PXP2_REG_PSWRQ_BW_WR, 0x106440},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, PXP2_REG_RQ_ILT_MODE, 0x1},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, PXP2_REG_RQ_RBC_DONE, 0x1},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
#define PXP2_COMMON_END 2061
#define MISC_AEU_COMMON_START 2061
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_ZR, MISC_REG_AEU_GENERAL_ATTN_0, 0x16},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_NIG_0, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_NIG_0, 0x55555555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE3_NIG_0, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_NIG_0, 0xf0000000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_PXP_0, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_PXP_0, 0x55555555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE3_PXP_0, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_PXP_0, 0xf0000000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_NIG_1, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_NIG_1, 0x55555555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE3_NIG_1, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_NIG_1, 0xf0000000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_PXP_1, 0x0},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_PXP_1, 0x10000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE3_PXP_1, 0x5014},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_PXP_1, 0x0},
{OP_WR_E1H, MISC_REG_AEU_CLR_LATCH_SIGNAL, 0xc00},
{OP_WR_E1H, MISC_REG_AEU_GENERAL_MASK, 0x3},
#define MISC_AEU_COMMON_END 2080
#define MISC_AEU_PORT0_START 2080
{OP_WR_E1, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, 0xbf5c0000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, 0xff5c0000},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_FUNC_0_OUT_0, 0xfff51fef},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_FUNC_0_OUT_0, 0xfff55fff},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, MISC_REG_AEU_ENABLE3_FUNC_0_OUT_0, 0xffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0, 0x500003e0},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0, 0xf00003e0},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1, 0x0},
{OP_WR, MISC_REG_AEU_ENABLE2_FUNC_0_OUT_1, 0xa000},
{OP_ZR, MISC_REG_AEU_ENABLE3_FUNC_0_OUT_1, 0x5},
{OP_WR, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_2, 0xfe00000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3, 0x14},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3, 0x7},
{OP_WR_E1, MISC_REG_AEU_ENABLE1_NIG_0, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_4, 0x400},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_NIG_0, 0x55555555},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_5, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE3_NIG_0, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_5, 0x1000},
{OP_WR_E1, MISC_REG_AEU_ENABLE4_NIG_0, 0x0},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_6, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE1_PXP_0, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_6, 0x4000},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_PXP_0, 0x55555555},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_7, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE3_PXP_0, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_0_OUT_7, 0x10000},
{OP_WR_E1, MISC_REG_AEU_ENABLE4_PXP_0, 0x0},
{OP_ZR_E1H, MISC_REG_AEU_INVERTER_1_FUNC_0, 0x4},
{OP_WR_E1, MISC_REG_AEU_INVERTER_1_FUNC_0, 0x0},
{OP_ZR_E1, MISC_REG_AEU_INVERTER_2_FUNC_0, 0x3},
{OP_WR_E1, MISC_REG_AEU_MASK_ATTN_FUNC_0, 0x7},
#define MISC_AEU_PORT0_END 2112
#define MISC_AEU_PORT1_START 2112
{OP_WR_E1, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0, 0xbf5c0000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0, 0xff5c0000},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0, 0xfff51fef},
{OP_WR_E1H, MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0, 0xfff55fff},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, MISC_REG_AEU_ENABLE3_FUNC_1_OUT_0, 0xffff},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_WR_E1, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0, 0x500003e0},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0, 0xf00003e0},
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
{OP_WR, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1, 0x0},
{OP_WR, MISC_REG_AEU_ENABLE2_FUNC_1_OUT_1, 0xa000},
{OP_ZR, MISC_REG_AEU_ENABLE3_FUNC_1_OUT_1, 0x5},
{OP_WR, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_2, 0xfe00000},
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
{OP_ZR_E1, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3, 0x14},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3, 0x7},
{OP_WR_E1, MISC_REG_AEU_ENABLE1_NIG_1, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_4, 0x800},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_NIG_1, 0x55555555},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_5, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE3_NIG_1, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_5, 0x2000},
{OP_WR_E1, MISC_REG_AEU_ENABLE4_NIG_1, 0x0},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_6, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE1_PXP_1, 0x55540000},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_6, 0x8000},
{OP_WR_E1, MISC_REG_AEU_ENABLE2_PXP_1, 0x55555555},
{OP_ZR_E1H, MISC_REG_AEU_ENABLE1_FUNC_1_OUT_7, 0x3},
{OP_WR_E1, MISC_REG_AEU_ENABLE3_PXP_1, 0x5555},
{OP_WR_E1H, MISC_REG_AEU_ENABLE4_FUNC_1_OUT_7, 0x20000},
{OP_WR_E1, MISC_REG_AEU_ENABLE4_PXP_1, 0x0},
{OP_ZR_E1H, MISC_REG_AEU_INVERTER_1_FUNC_1, 0x4},
{OP_WR_E1, MISC_REG_AEU_INVERTER_1_FUNC_1, 0x0},
{OP_ZR_E1, MISC_REG_AEU_INVERTER_2_FUNC_1, 0x3},
{OP_WR_E1, MISC_REG_AEU_MASK_ATTN_FUNC_1, 0x7},
#define MISC_AEU_PORT1_END 2144
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
};
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
static const u32 init_data_e1[] = {
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
0x00010000, 0x000204c0, 0x00030980, 0x00040e40, 0x00051300, 0x000617c0,
0x00071c80, 0x00082140, 0x00092600, 0x000a2ac0, 0x000b2f80, 0x000c3440,
0x000d3900, 0x000e3dc0, 0x000f4280, 0x00104740, 0x00114c00, 0x001250c0,
0x00135580, 0x00145a40, 0x00155f00, 0x001663c0, 0x00176880, 0x00186d40,
0x00197200, 0x001a76c0, 0x001b7b80, 0x001c8040, 0x001d8500, 0x001e89c0,
0x001f8e80, 0x00209340, 0x00002000, 0x00004000, 0x00006000, 0x00008000,
0x0000a000, 0x0000c000, 0x0000e000, 0x00010000, 0x00012000, 0x00014000,
0x00016000, 0x00018000, 0x0001a000, 0x0001c000, 0x0001e000, 0x00020000,
0x00022000, 0x00024000, 0x00026000, 0x00028000, 0x0002a000, 0x0002c000,
0x0002e000, 0x00030000, 0x00032000, 0x00034000, 0x00036000, 0x00038000,
0x0003a000, 0x0003c000, 0x0003e000, 0x00040000, 0x00042000, 0x00044000,
0x00046000, 0x00048000, 0x0004a000, 0x0004c000, 0x0004e000, 0x00050000,
0x00052000, 0x00054000, 0x00056000, 0x00058000, 0x0005a000, 0x0005c000,
0x0005e000, 0x00060000, 0x00062000, 0x00064000, 0x00066000, 0x00068000,
0x0006a000, 0x0006c000, 0x0006e000, 0x00070000, 0x00072000, 0x00074000,
0x00076000, 0x00078000, 0x0007a000, 0x0007c000, 0x0007e000, 0x00080000,
0x00082000, 0x00084000, 0x00086000, 0x00088000, 0x0008a000, 0x0008c000,
0x0008e000, 0x00090000, 0x00092000, 0x00094000, 0x00096000, 0x00098000,
0x0009a000, 0x0009c000, 0x0009e000, 0x000a0000, 0x000a2000, 0x000a4000,
0x000a6000, 0x000a8000, 0x000aa000, 0x000ac000, 0x000ae000, 0x000b0000,
0x000b2000, 0x000b4000, 0x000b6000, 0x000b8000, 0x000ba000, 0x000bc000,
0x000be000, 0x000c0000, 0x000c2000, 0x000c4000, 0x000c6000, 0x000c8000,
0x000ca000, 0x000cc000, 0x000ce000, 0x000d0000, 0x000d2000, 0x000d4000,
0x000d6000, 0x000d8000, 0x000da000, 0x000dc000, 0x000de000, 0x000e0000,
0x000e2000, 0x000e4000, 0x000e6000, 0x000e8000, 0x000ea000, 0x000ec000,
0x000ee000, 0x000f0000, 0x000f2000, 0x000f4000, 0x000f6000, 0x000f8000,
0x000fa000, 0x000fc000, 0x000fe000, 0x00100000, 0x00102000, 0x00104000,
0x00106000, 0x00108000, 0x0010a000, 0x0010c000, 0x0010e000, 0x00110000,
0x00112000, 0x00114000, 0x00116000, 0x00118000, 0x0011a000, 0x0011c000,
0x0011e000, 0x00120000, 0x00122000, 0x00124000, 0x00126000, 0x00128000,
0x0012a000, 0x0012c000, 0x0012e000, 0x00130000, 0x00132000, 0x00134000,
0x00136000, 0x00138000, 0x0013a000, 0x0013c000, 0x0013e000, 0x00140000,
0x00142000, 0x00144000, 0x00146000, 0x00148000, 0x0014a000, 0x0014c000,
0x0014e000, 0x00150000, 0x00152000, 0x00154000, 0x00156000, 0x00158000,
0x0015a000, 0x0015c000, 0x0015e000, 0x00160000, 0x00162000, 0x00164000,
0x00166000, 0x00168000, 0x0016a000, 0x0016c000, 0x0016e000, 0x00170000,
0x00172000, 0x00174000, 0x00176000, 0x00178000, 0x0017a000, 0x0017c000,
0x0017e000, 0x00180000, 0x00182000, 0x00184000, 0x00186000, 0x00188000,
0x0018a000, 0x0018c000, 0x0018e000, 0x00190000, 0x00192000, 0x00194000,
0x00196000, 0x00198000, 0x0019a000, 0x0019c000, 0x0019e000, 0x001a0000,
0x001a2000, 0x001a4000, 0x001a6000, 0x001a8000, 0x001aa000, 0x001ac000,
0x001ae000, 0x001b0000, 0x001b2000, 0x001b4000, 0x001b6000, 0x001b8000,
0x001ba000, 0x001bc000, 0x001be000, 0x001c0000, 0x001c2000, 0x001c4000,
0x001c6000, 0x001c8000, 0x001ca000, 0x001cc000, 0x001ce000, 0x001d0000,
0x001d2000, 0x001d4000, 0x001d6000, 0x001d8000, 0x001da000, 0x001dc000,
0x001de000, 0x001e0000, 0x001e2000, 0x001e4000, 0x001e6000, 0x001e8000,
0x001ea000, 0x001ec000, 0x001ee000, 0x001f0000, 0x001f2000, 0x001f4000,
0x001f6000, 0x001f8000, 0x001fa000, 0x001fc000, 0x001fe000, 0x00200000,
0x00202000, 0x00204000, 0x00206000, 0x00208000, 0x0020a000, 0x0020c000,
0x0020e000, 0x00210000, 0x00212000, 0x00214000, 0x00216000, 0x00218000,
0x0021a000, 0x0021c000, 0x0021e000, 0x00220000, 0x00222000, 0x00224000,
0x00226000, 0x00228000, 0x0022a000, 0x0022c000, 0x0022e000, 0x00230000,
0x00232000, 0x00234000, 0x00236000, 0x00238000, 0x0023a000, 0x0023c000,
0x0023e000, 0x00240000, 0x00242000, 0x00244000, 0x00246000, 0x00248000,
0x0024a000, 0x0024c000, 0x0024e000, 0x00250000, 0x00252000, 0x00254000,
0x00256000, 0x00258000, 0x0025a000, 0x0025c000, 0x0025e000, 0x00260000,
0x00262000, 0x00264000, 0x00266000, 0x00268000, 0x0026a000, 0x0026c000,
0x0026e000, 0x00270000, 0x00272000, 0x00274000, 0x00276000, 0x00278000,
0x0027a000, 0x0027c000, 0x0027e000, 0x00280000, 0x00282000, 0x00284000,
0x00286000, 0x00288000, 0x0028a000, 0x0028c000, 0x0028e000, 0x00290000,
0x00292000, 0x00294000, 0x00296000, 0x00298000, 0x0029a000, 0x0029c000,
0x0029e000, 0x002a0000, 0x002a2000, 0x002a4000, 0x002a6000, 0x002a8000,
0x002aa000, 0x002ac000, 0x002ae000, 0x002b0000, 0x002b2000, 0x002b4000,
0x002b6000, 0x002b8000, 0x002ba000, 0x002bc000, 0x002be000, 0x002c0000,
0x002c2000, 0x002c4000, 0x002c6000, 0x002c8000, 0x002ca000, 0x002cc000,
0x002ce000, 0x002d0000, 0x002d2000, 0x002d4000, 0x002d6000, 0x002d8000,
0x002da000, 0x002dc000, 0x002de000, 0x002e0000, 0x002e2000, 0x002e4000,
0x002e6000, 0x002e8000, 0x002ea000, 0x002ec000, 0x002ee000, 0x002f0000,
0x002f2000, 0x002f4000, 0x002f6000, 0x002f8000, 0x002fa000, 0x002fc000,
0x002fe000, 0x00300000, 0x00302000, 0x00304000, 0x00306000, 0x00308000,
0x0030a000, 0x0030c000, 0x0030e000, 0x00310000, 0x00312000, 0x00314000,
0x00316000, 0x00318000, 0x0031a000, 0x0031c000, 0x0031e000, 0x00320000,
0x00322000, 0x00324000, 0x00326000, 0x00328000, 0x0032a000, 0x0032c000,
0x0032e000, 0x00330000, 0x00332000, 0x00334000, 0x00336000, 0x00338000,
0x0033a000, 0x0033c000, 0x0033e000, 0x00340000, 0x00342000, 0x00344000,
0x00346000, 0x00348000, 0x0034a000, 0x0034c000, 0x0034e000, 0x00350000,
0x00352000, 0x00354000, 0x00356000, 0x00358000, 0x0035a000, 0x0035c000,
0x0035e000, 0x00360000, 0x00362000, 0x00364000, 0x00366000, 0x00368000,
0x0036a000, 0x0036c000, 0x0036e000, 0x00370000, 0x00372000, 0x00374000,
0x00376000, 0x00378000, 0x0037a000, 0x0037c000, 0x0037e000, 0x00380000,
0x00382000, 0x00384000, 0x00386000, 0x00388000, 0x0038a000, 0x0038c000,
0x0038e000, 0x00390000, 0x00392000, 0x00394000, 0x00396000, 0x00398000,
0x0039a000, 0x0039c000, 0x0039e000, 0x003a0000, 0x003a2000, 0x003a4000,
0x003a6000, 0x003a8000, 0x003aa000, 0x003ac000, 0x003ae000, 0x003b0000,
0x003b2000, 0x003b4000, 0x003b6000, 0x003b8000, 0x003ba000, 0x003bc000,
0x003be000, 0x003c0000, 0x003c2000, 0x003c4000, 0x003c6000, 0x003c8000,
0x003ca000, 0x003cc000, 0x003ce000, 0x003d0000, 0x003d2000, 0x003d4000,
0x003d6000, 0x003d8000, 0x003da000, 0x003dc000, 0x003de000, 0x003e0000,
0x003e2000, 0x003e4000, 0x003e6000, 0x003e8000, 0x003ea000, 0x003ec000,
0x003ee000, 0x003f0000, 0x003f2000, 0x003f4000, 0x003f6000, 0x003f8000,
bnx2x: Remove old microcode Removing the old Microcode from the BLOB - broken into a separate patch to make it small enough for the mailing list Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:30:11 +00:00
0x003fa000, 0x003fc000, 0x003fe000, 0x003fe001, 0x00000000, 0x000001ff
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
};
bnx2x: New init infrastructure This new initialization code supports the 57711 HW. It also supports the emulation and FPGA for the 57711 and 57710 initializations values (very small amount of code which is very helpful in the lab - less than 30 lines). The initialization is done via DMAE after the DMAE block is ready - before it is ready, some of the initialization is done via PCI configuration transactions (referred to as indirect write). A mutex to protect the DMAE from being overlapped was added. There are few new registers which needs to be initialized by SW - the full comment for those registers is added to the register file. A place holder for the 57711 (referred to as E1H) microcode was added- the microcode itself is too big and it is split over the following 4 patches Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-24 03:29:02 +00:00
static const u32 init_data_e1h[] = {
};
static const u32 tsem_int_table_data_e1[] = {
};
static const u32 tsem_pram_data_e1[] = {
};
static const u32 usem_int_table_data_e1[] = {
};
static const u32 usem_pram_data_e1[] = {
};
static const u32 csem_int_table_data_e1[] = {
};
static const u32 csem_pram_data_e1[] = {
};
static const u32 xsem_int_table_data_e1[] = {
};
static const u32 xsem_pram_data_e1[] = {
};
static const u32 tsem_int_table_data_e1h[] = {
};
static const u32 tsem_pram_data_e1h[] = {
};
static const u32 usem_int_table_data_e1h[] = {
};
static const u32 usem_pram_data_e1h[] = {
};
static const u32 csem_int_table_data_e1h[] = {
};
static const u32 csem_pram_data_e1h[] = {
};
static const u32 xsem_int_table_data_e1h[] = {
};
static const u32 xsem_pram_data_e1h[] = {
};
add bnx2x driver for BCM57710 Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-11-15 18:09:02 +00:00
#endif /*__BNX2X_INIT_VALUES_H__*/
Reference in New Issue Copy Permalink