linux/net/dsa/dsa.c

491 lines
11 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-or-later
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
/*
* net/dsa/dsa.c - Hardware switch handling
dsa: add switch chip cascading support The initial version of the DSA driver only supported a single switch chip per network interface, while DSA-capable switch chips can be interconnected to form a tree of switch chips. This patch adds support for multiple switch chips on a network interface. An example topology for a 16-port device with an embedded CPU is as follows: +-----+ +--------+ +--------+ | |eth0 10| switch |9 10| switch | | CPU +----------+ +-------+ | | | | chip 0 | | chip 1 | +-----+ +---++---+ +---++---+ || || || || ||1000baseT ||1000baseT ||ports 1-8 ||ports 9-16 This requires a couple of interdependent changes in the DSA layer: - The dsa platform driver data needs to be extended: there is still only one netdevice per DSA driver instance (eth0 in the example above), but each of the switch chips in the tree needs its own mii_bus device pointer, MII management bus address, and port name array. (include/net/dsa.h) The existing in-tree dsa users need some small changes to deal with this. (arch/arm) - The DSA and Ethertype DSA tagging modules need to be extended to use the DSA device ID field on receive and demultiplex the packet accordingly, and fill in the DSA device ID field on transmit according to which switch chip the packet is heading to. (net/dsa/tag_{dsa,edsa}.c) - The concept of "CPU port", which is the switch chip port that the CPU is connected to (port 10 on switch chip 0 in the example), needs to be extended with the concept of "upstream port", which is the port on the switch chip that will bring us one hop closer to the CPU (port 10 for both switch chips in the example above). - The dsa platform data needs to specify which ports on which switch chips are links to other switch chips, so that we can enable DSA tagging mode on them. (For inter-switch links, we always use non-EtherType DSA tagging, since it has lower overhead. The CPU link uses dsa or edsa tagging depending on what the 'root' switch chip supports.) This is done by specifying "dsa" for the given port in the port array. - The dsa platform data needs to be extended with information on via which port to reach any given switch chip from any given switch chip. This info is specified via the per-switch chip data struct ->rtable[] array, which gives the nexthop ports for each of the other switches in the tree. For the example topology above, the dsa platform data would look something like this: static struct dsa_chip_data sw[2] = { { .mii_bus = &foo, .sw_addr = 1, .port_names[0] = "p1", .port_names[1] = "p2", .port_names[2] = "p3", .port_names[3] = "p4", .port_names[4] = "p5", .port_names[5] = "p6", .port_names[6] = "p7", .port_names[7] = "p8", .port_names[9] = "dsa", .port_names[10] = "cpu", .rtable = (s8 []){ -1, 9, }, }, { .mii_bus = &foo, .sw_addr = 2, .port_names[0] = "p9", .port_names[1] = "p10", .port_names[2] = "p11", .port_names[3] = "p12", .port_names[4] = "p13", .port_names[5] = "p14", .port_names[6] = "p15", .port_names[7] = "p16", .port_names[10] = "dsa", .rtable = (s8 []){ 10, -1, }, }, }, static struct dsa_platform_data pd = { .netdev = &foo, .nr_switches = 2, .sw = sw, }; Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Gary Thomas <gary@mlbassoc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-20 09:52:09 +00:00
* Copyright (c) 2008-2009 Marvell Semiconductor
* Copyright (c) 2013 Florian Fainelli <florian@openwrt.org>
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
*/
#include <linux/device.h>
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
#include <linux/list.h>
#include <linux/platform_device.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 08:04:11 +00:00
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/notifier.h>
#include <linux/of.h>
#include <linux/of_mdio.h>
#include <linux/of_platform.h>
#include <linux/of_net.h>
#include <linux/netdevice.h>
#include <linux/sysfs.h>
#include <linux/phy_fixed.h>
#include <linux/ptp_classify.h>
#include <linux/etherdevice.h>
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
#include "dsa_priv.h"
static LIST_HEAD(dsa_tag_drivers_list);
static DEFINE_MUTEX(dsa_tag_drivers_lock);
static struct sk_buff *dsa_slave_notag_xmit(struct sk_buff *skb,
struct net_device *dev)
{
/* Just return the original SKB */
return skb;
}
static const struct dsa_device_ops none_ops = {
.name = "none",
.proto = DSA_TAG_PROTO_NONE,
.xmit = dsa_slave_notag_xmit,
.rcv = NULL,
};
DSA_TAG_DRIVER(none_ops);
static void dsa_tag_driver_register(struct dsa_tag_driver *dsa_tag_driver,
struct module *owner)
{
dsa_tag_driver->owner = owner;
mutex_lock(&dsa_tag_drivers_lock);
list_add_tail(&dsa_tag_driver->list, &dsa_tag_drivers_list);
mutex_unlock(&dsa_tag_drivers_lock);
}
void dsa_tag_drivers_register(struct dsa_tag_driver *dsa_tag_driver_array[],
unsigned int count, struct module *owner)
{
unsigned int i;
for (i = 0; i < count; i++)
dsa_tag_driver_register(dsa_tag_driver_array[i], owner);
}
static void dsa_tag_driver_unregister(struct dsa_tag_driver *dsa_tag_driver)
{
mutex_lock(&dsa_tag_drivers_lock);
list_del(&dsa_tag_driver->list);
mutex_unlock(&dsa_tag_drivers_lock);
}
EXPORT_SYMBOL_GPL(dsa_tag_drivers_register);
void dsa_tag_drivers_unregister(struct dsa_tag_driver *dsa_tag_driver_array[],
unsigned int count)
{
unsigned int i;
for (i = 0; i < count; i++)
dsa_tag_driver_unregister(dsa_tag_driver_array[i]);
}
EXPORT_SYMBOL_GPL(dsa_tag_drivers_unregister);
const char *dsa_tag_protocol_to_str(const struct dsa_device_ops *ops)
{
return ops->name;
};
const struct dsa_device_ops *dsa_tag_driver_get(int tag_protocol)
{
struct dsa_tag_driver *dsa_tag_driver;
const struct dsa_device_ops *ops;
bool found = false;
request_module("%s%d", DSA_TAG_DRIVER_ALIAS, tag_protocol);
mutex_lock(&dsa_tag_drivers_lock);
list_for_each_entry(dsa_tag_driver, &dsa_tag_drivers_list, list) {
ops = dsa_tag_driver->ops;
if (ops->proto == tag_protocol) {
found = true;
break;
}
}
if (found) {
if (!try_module_get(dsa_tag_driver->owner))
ops = ERR_PTR(-ENOPROTOOPT);
} else {
ops = ERR_PTR(-ENOPROTOOPT);
}
mutex_unlock(&dsa_tag_drivers_lock);
return ops;
}
void dsa_tag_driver_put(const struct dsa_device_ops *ops)
{
struct dsa_tag_driver *dsa_tag_driver;
mutex_lock(&dsa_tag_drivers_lock);
list_for_each_entry(dsa_tag_driver, &dsa_tag_drivers_list, list) {
if (dsa_tag_driver->ops == ops) {
module_put(dsa_tag_driver->owner);
break;
}
}
mutex_unlock(&dsa_tag_drivers_lock);
}
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
static int dev_is_class(struct device *dev, void *class)
{
if (dev->class != NULL && !strcmp(dev->class->name, class))
return 1;
return 0;
}
static struct device *dev_find_class(struct device *parent, char *class)
{
if (dev_is_class(parent, class)) {
get_device(parent);
return parent;
}
return device_find_child(parent, class, dev_is_class);
}
struct net_device *dsa_dev_to_net_device(struct device *dev)
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
{
struct device *d;
d = dev_find_class(dev, "net");
if (d != NULL) {
struct net_device *nd;
nd = to_net_dev(d);
dev_hold(nd);
put_device(d);
return nd;
}
return NULL;
}
EXPORT_SYMBOL_GPL(dsa_dev_to_net_device);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
/* Determine if we should defer delivery of skb until we have a rx timestamp.
*
* Called from dsa_switch_rcv. For now, this will only work if tagging is
* enabled on the switch. Normally the MAC driver would retrieve the hardware
* timestamp when it reads the packet out of the hardware. However in a DSA
* switch, the DSA driver owning the interface to which the packet is
* delivered is never notified unless we do so here.
*/
static bool dsa_skb_defer_rx_timestamp(struct dsa_slave_priv *p,
struct sk_buff *skb)
{
struct dsa_switch *ds = p->dp->ds;
unsigned int type;
if (skb_headroom(skb) < ETH_HLEN)
return false;
__skb_push(skb, ETH_HLEN);
type = ptp_classify_raw(skb);
__skb_pull(skb, ETH_HLEN);
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
return false;
}
static int dsa_switch_rcv(struct sk_buff *skb, struct net_device *dev,
struct packet_type *pt, struct net_device *unused)
{
struct dsa_port *cpu_dp = dev->dsa_ptr;
struct sk_buff *nskb = NULL;
struct dsa_slave_priv *p;
if (unlikely(!cpu_dp)) {
kfree_skb(skb);
return 0;
}
skb = skb_unshare(skb, GFP_ATOMIC);
if (!skb)
return 0;
nskb = cpu_dp->rcv(skb, dev, pt);
if (!nskb) {
kfree_skb(skb);
return 0;
}
skb = nskb;
p = netdev_priv(skb->dev);
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
if (unlikely(cpu_dp->ds->untag_bridge_pvid)) {
nskb = dsa_untag_bridge_pvid(skb);
if (!nskb) {
kfree_skb(skb);
return 0;
}
skb = nskb;
}
dev_sw_netstats_rx_add(skb->dev, skb->len);
if (dsa_skb_defer_rx_timestamp(p, skb))
return 0;
net: dsa: add GRO support via gro_cells gro_cells lib is used by different encapsulating netdevices, such as geneve, macsec, vxlan etc. to speed up decapsulated traffic processing. CPU tag is a sort of "encapsulation", and we can use the same mechs to greatly improve overall DSA performance. skbs are passed to the GRO layer after removing CPU tags, so we don't need any new packet offload types as it was firstly proposed by me in the first GRO-over-DSA variant [1]. The size of struct gro_cells is sizeof(void *), so hot struct dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields remain in one 32-byte cacheline. The other positive side effect is that drivers for network devices that can be shipped as CPU ports of DSA-driven switches can now use napi_gro_frags() to pass skbs to kernel. Packets built that way are completely non-linear and are likely being dropped without GRO. This was tested on to-be-mainlined-soon Ethernet driver that uses napi_gro_frags(), and the overall performance was on par with the variant from [1], sometimes even better due to minimal overhead. net.core.gro_normal_batch tuning may help to push it to the limit on particular setups and platforms. iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup on 1.2 GHz MIPS board: 5.7-rc2 baseline: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender [ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver Iface RX packets TX packets eth0 7097731 7097702 port0 426050 6671829 port1 6671681 425862 port1.218 6671677 425851 With this patch: [ID] Interval Transfer Bitrate Retr [ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender [ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver Iface RX packets TX packets eth0 9474792 9474777 port0 455200 353288 port1 9019592 455035 port1.218 353144 455024 v2: - Add some performance examples in the commit message; - No functional changes. [1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/ Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21 13:41:08 +00:00
gro_cells_receive(&p->gcells, skb);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static bool dsa_is_port_initialized(struct dsa_switch *ds, int p)
{
const struct dsa_port *dp = dsa_to_port(ds, p);
return dp->type == DSA_PORT_TYPE_USER && dp->slave;
}
int dsa_switch_suspend(struct dsa_switch *ds)
{
int i, ret = 0;
/* Suspend slave network devices */
for (i = 0; i < ds->num_ports; i++) {
if (!dsa_is_port_initialized(ds, i))
continue;
ret = dsa_slave_suspend(dsa_to_port(ds, i)->slave);
if (ret)
return ret;
}
if (ds->ops->suspend)
ret = ds->ops->suspend(ds);
return ret;
}
EXPORT_SYMBOL_GPL(dsa_switch_suspend);
int dsa_switch_resume(struct dsa_switch *ds)
{
int i, ret = 0;
if (ds->ops->resume)
ret = ds->ops->resume(ds);
if (ret)
return ret;
/* Resume slave network devices */
for (i = 0; i < ds->num_ports; i++) {
if (!dsa_is_port_initialized(ds, i))
continue;
ret = dsa_slave_resume(dsa_to_port(ds, i)->slave);
if (ret)
return ret;
}
return 0;
}
EXPORT_SYMBOL_GPL(dsa_switch_resume);
#endif
static struct packet_type dsa_pack_type __read_mostly = {
.type = cpu_to_be16(ETH_P_XDSA),
.func = dsa_switch_rcv,
};
static struct workqueue_struct *dsa_owq;
bool dsa_schedule_work(struct work_struct *work)
{
return queue_work(dsa_owq, work);
}
static ATOMIC_NOTIFIER_HEAD(dsa_notif_chain);
int register_dsa_notifier(struct notifier_block *nb)
{
return atomic_notifier_chain_register(&dsa_notif_chain, nb);
}
EXPORT_SYMBOL_GPL(register_dsa_notifier);
int unregister_dsa_notifier(struct notifier_block *nb)
{
return atomic_notifier_chain_unregister(&dsa_notif_chain, nb);
}
EXPORT_SYMBOL_GPL(unregister_dsa_notifier);
int call_dsa_notifiers(unsigned long val, struct net_device *dev,
struct dsa_notifier_info *info)
{
info->dev = dev;
return atomic_notifier_call_chain(&dsa_notif_chain, val, info);
}
EXPORT_SYMBOL_GPL(call_dsa_notifiers);
int dsa_devlink_param_get(struct devlink *dl, u32 id,
struct devlink_param_gset_ctx *ctx)
{
struct dsa_switch *ds = dsa_devlink_to_ds(dl);
if (!ds->ops->devlink_param_get)
return -EOPNOTSUPP;
return ds->ops->devlink_param_get(ds, id, ctx);
}
EXPORT_SYMBOL_GPL(dsa_devlink_param_get);
int dsa_devlink_param_set(struct devlink *dl, u32 id,
struct devlink_param_gset_ctx *ctx)
{
struct dsa_switch *ds = dsa_devlink_to_ds(dl);
if (!ds->ops->devlink_param_set)
return -EOPNOTSUPP;
return ds->ops->devlink_param_set(ds, id, ctx);
}
EXPORT_SYMBOL_GPL(dsa_devlink_param_set);
int dsa_devlink_params_register(struct dsa_switch *ds,
const struct devlink_param *params,
size_t params_count)
{
return devlink_params_register(ds->devlink, params, params_count);
}
EXPORT_SYMBOL_GPL(dsa_devlink_params_register);
void dsa_devlink_params_unregister(struct dsa_switch *ds,
const struct devlink_param *params,
size_t params_count)
{
devlink_params_unregister(ds->devlink, params, params_count);
}
EXPORT_SYMBOL_GPL(dsa_devlink_params_unregister);
int dsa_devlink_resource_register(struct dsa_switch *ds,
const char *resource_name,
u64 resource_size,
u64 resource_id,
u64 parent_resource_id,
const struct devlink_resource_size_params *size_params)
{
return devlink_resource_register(ds->devlink, resource_name,
resource_size, resource_id,
parent_resource_id,
size_params);
}
EXPORT_SYMBOL_GPL(dsa_devlink_resource_register);
void dsa_devlink_resources_unregister(struct dsa_switch *ds)
{
devlink_resources_unregister(ds->devlink, NULL);
}
EXPORT_SYMBOL_GPL(dsa_devlink_resources_unregister);
void dsa_devlink_resource_occ_get_register(struct dsa_switch *ds,
u64 resource_id,
devlink_resource_occ_get_t *occ_get,
void *occ_get_priv)
{
return devlink_resource_occ_get_register(ds->devlink, resource_id,
occ_get, occ_get_priv);
}
EXPORT_SYMBOL_GPL(dsa_devlink_resource_occ_get_register);
void dsa_devlink_resource_occ_get_unregister(struct dsa_switch *ds,
u64 resource_id)
{
devlink_resource_occ_get_unregister(ds->devlink, resource_id);
}
EXPORT_SYMBOL_GPL(dsa_devlink_resource_occ_get_unregister);
struct devlink_region *
dsa_devlink_region_create(struct dsa_switch *ds,
const struct devlink_region_ops *ops,
u32 region_max_snapshots, u64 region_size)
{
return devlink_region_create(ds->devlink, ops, region_max_snapshots,
region_size);
}
EXPORT_SYMBOL_GPL(dsa_devlink_region_create);
struct devlink_region *
dsa_devlink_port_region_create(struct dsa_switch *ds,
int port,
const struct devlink_port_region_ops *ops,
u32 region_max_snapshots, u64 region_size)
{
struct dsa_port *dp = dsa_to_port(ds, port);
return devlink_port_region_create(&dp->devlink_port, ops,
region_max_snapshots,
region_size);
}
EXPORT_SYMBOL_GPL(dsa_devlink_port_region_create);
void dsa_devlink_region_destroy(struct devlink_region *region)
{
devlink_region_destroy(region);
}
EXPORT_SYMBOL_GPL(dsa_devlink_region_destroy);
net: dsa: introduce a dsa_port_from_netdev public helper As its implementation shows, this is synonimous with calling dsa_slave_dev_check followed by dsa_slave_to_port, so it is quite simple already and provides functionality which is already there. However there is now a need for these functions outside dsa_priv.h, for example in drivers that perform mirroring and redirection through tc-flower offloads (they are given raw access to the flow_cls_offload structure), where they need to call this function on act->dev. But simply exporting dsa_slave_to_port would make it non-inline and would result in an extra function call in the hotpath, as can be seen for example in sja1105: Before: 000006dc <sja1105_xmit>: { 6dc: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr} 6e0: e1a04000 mov r4, r0 6e4: e591958c ldr r9, [r1, #1420] ; 0x58c <- Inline dsa_slave_to_port 6e8: e1a05001 mov r5, r1 6ec: e24dd004 sub sp, sp, #4 u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index); 6f0: e1c901d8 ldrd r0, [r9, #24] 6f4: ebfffffe bl 0 <dsa_8021q_tx_vid> 6f4: R_ARM_CALL dsa_8021q_tx_vid u8 pcp = netdev_txq_to_tc(netdev, queue_mapping); 6f8: e1d416b0 ldrh r1, [r4, #96] ; 0x60 u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index); 6fc: e1a08000 mov r8, r0 After: 000006e4 <sja1105_xmit>: { 6e4: e92d4ff0 push {r4, r5, r6, r7, r8, r9, sl, fp, lr} 6e8: e1a04000 mov r4, r0 6ec: e24dd004 sub sp, sp, #4 struct dsa_port *dp = dsa_slave_to_port(netdev); 6f0: e1a00001 mov r0, r1 { 6f4: e1a05001 mov r5, r1 struct dsa_port *dp = dsa_slave_to_port(netdev); 6f8: ebfffffe bl 0 <dsa_slave_to_port> 6f8: R_ARM_CALL dsa_slave_to_port 6fc: e1a09000 mov r9, r0 u16 tx_vid = dsa_8021q_tx_vid(dp->ds, dp->index); 700: e1c001d8 ldrd r0, [r0, #24] 704: ebfffffe bl 0 <dsa_8021q_tx_vid> 704: R_ARM_CALL dsa_8021q_tx_vid Because we want to avoid possible performance regressions, introduce this new function which is designed to be public. Suggested-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-05 19:20:52 +00:00
struct dsa_port *dsa_port_from_netdev(struct net_device *netdev)
{
if (!netdev || !dsa_slave_dev_check(netdev))
return ERR_PTR(-ENODEV);
return dsa_slave_to_port(netdev);
}
EXPORT_SYMBOL_GPL(dsa_port_from_netdev);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
static int __init dsa_init_module(void)
{
int rc;
dsa_owq = alloc_ordered_workqueue("dsa_ordered",
WQ_MEM_RECLAIM);
if (!dsa_owq)
return -ENOMEM;
rc = dsa_slave_register_notifier();
if (rc)
net: dsa: Fix error cleanup path in dsa_init_module BUG: unable to handle kernel paging request at ffffffffa01c5430 PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bc5067 PTE 0 Oops: 0000 [#1 CPU: 0 PID: 6159 Comm: modprobe Not tainted 5.1.0+ #33 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 RIP: 0010:raw_notifier_chain_register+0x16/0x40 Code: 63 f8 66 90 e9 5d ff ff ff 90 90 90 90 90 90 90 90 90 90 90 55 48 8b 07 48 89 e5 48 85 c0 74 1c 8b 56 10 3b 50 10 7e 07 eb 12 <39> 50 10 7c 0d 48 8d 78 08 48 8b 40 08 48 85 c0 75 ee 48 89 46 08 RSP: 0018:ffffc90001c33c08 EFLAGS: 00010282 RAX: ffffffffa01c5420 RBX: ffffffffa01db420 RCX: 4fcef45928070a8b RDX: 0000000000000000 RSI: ffffffffa01db420 RDI: ffffffffa01b0068 RBP: ffffc90001c33c08 R08: 000000003e0a33d0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000094443661 R12: ffff88822c320700 R13: ffff88823109be80 R14: 0000000000000000 R15: ffffc90001c33e78 FS: 00007fab8bd08540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa01c5430 CR3: 00000002297ea000 CR4: 00000000000006f0 Call Trace: register_netdevice_notifier+0x43/0x250 ? 0xffffffffa01e0000 dsa_slave_register_notifier+0x13/0x70 [dsa_core ? 0xffffffffa01e0000 dsa_init_module+0x2e/0x1000 [dsa_core do_one_initcall+0x6c/0x3cc ? do_init_module+0x22/0x1f1 ? rcu_read_lock_sched_held+0x97/0xb0 ? kmem_cache_alloc_trace+0x325/0x3b0 do_init_module+0x5b/0x1f1 load_module+0x1db1/0x2690 ? m_show+0x1d0/0x1d0 __do_sys_finit_module+0xc5/0xd0 __x64_sys_finit_module+0x15/0x20 do_syscall_64+0x6b/0x1d0 entry_SYSCALL_64_after_hwframe+0x49/0xbe Cleanup allocated resourses if there are errors, otherwise it will trgger memleak. Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-06 15:25:29 +00:00
goto register_notifier_fail;
dev_add_pack(&dsa_pack_type);
dsa_tag_driver_register(&DSA_TAG_DRIVER_NAME(none_ops),
THIS_MODULE);
return 0;
net: dsa: Fix error cleanup path in dsa_init_module BUG: unable to handle kernel paging request at ffffffffa01c5430 PGD 3270067 P4D 3270067 PUD 3271063 PMD 230bc5067 PTE 0 Oops: 0000 [#1 CPU: 0 PID: 6159 Comm: modprobe Not tainted 5.1.0+ #33 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 RIP: 0010:raw_notifier_chain_register+0x16/0x40 Code: 63 f8 66 90 e9 5d ff ff ff 90 90 90 90 90 90 90 90 90 90 90 55 48 8b 07 48 89 e5 48 85 c0 74 1c 8b 56 10 3b 50 10 7e 07 eb 12 <39> 50 10 7c 0d 48 8d 78 08 48 8b 40 08 48 85 c0 75 ee 48 89 46 08 RSP: 0018:ffffc90001c33c08 EFLAGS: 00010282 RAX: ffffffffa01c5420 RBX: ffffffffa01db420 RCX: 4fcef45928070a8b RDX: 0000000000000000 RSI: ffffffffa01db420 RDI: ffffffffa01b0068 RBP: ffffc90001c33c08 R08: 000000003e0a33d0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000094443661 R12: ffff88822c320700 R13: ffff88823109be80 R14: 0000000000000000 R15: ffffc90001c33e78 FS: 00007fab8bd08540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa01c5430 CR3: 00000002297ea000 CR4: 00000000000006f0 Call Trace: register_netdevice_notifier+0x43/0x250 ? 0xffffffffa01e0000 dsa_slave_register_notifier+0x13/0x70 [dsa_core ? 0xffffffffa01e0000 dsa_init_module+0x2e/0x1000 [dsa_core do_one_initcall+0x6c/0x3cc ? do_init_module+0x22/0x1f1 ? rcu_read_lock_sched_held+0x97/0xb0 ? kmem_cache_alloc_trace+0x325/0x3b0 do_init_module+0x5b/0x1f1 load_module+0x1db1/0x2690 ? m_show+0x1d0/0x1d0 __do_sys_finit_module+0xc5/0xd0 __x64_sys_finit_module+0x15/0x20 do_syscall_64+0x6b/0x1d0 entry_SYSCALL_64_after_hwframe+0x49/0xbe Cleanup allocated resourses if there are errors, otherwise it will trgger memleak. Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-06 15:25:29 +00:00
register_notifier_fail:
destroy_workqueue(dsa_owq);
return rc;
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
}
module_init(dsa_init_module);
static void __exit dsa_cleanup_module(void)
{
dsa_tag_driver_unregister(&DSA_TAG_DRIVER_NAME(none_ops));
dsa_slave_unregister_notifier();
dev_remove_pack(&dsa_pack_type);
destroy_workqueue(dsa_owq);
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
}
module_exit(dsa_cleanup_module);
MODULE_AUTHOR("Lennert Buytenhek <buytenh@wantstofly.org>");
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
MODULE_DESCRIPTION("Driver for Distributed Switch Architecture switch chips");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:dsa");