linux/drivers/pci/host/pcie-designware.c

903 lines
24 KiB
C
Raw Normal View History

/*
* Synopsys Designware PCIe host controller driver
*
* Copyright (C) 2013 Samsung Electronics Co., Ltd.
* http://www.samsung.com
*
* Author: Jingoo Han <jg1.han@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/msi.h>
#include <linux/of_address.h>
#include <linux/of_pci.h>
#include <linux/pci.h>
#include <linux/pci_regs.h>
#include <linux/platform_device.h>
#include <linux/types.h>
#include "pcie-designware.h"
/* Synopsis specific PCIE configuration registers */
#define PCIE_PORT_LINK_CONTROL 0x710
#define PORT_LINK_MODE_MASK (0x3f << 16)
#define PORT_LINK_MODE_1_LANES (0x1 << 16)
#define PORT_LINK_MODE_2_LANES (0x3 << 16)
#define PORT_LINK_MODE_4_LANES (0x7 << 16)
#define PCIE_LINK_WIDTH_SPEED_CONTROL 0x80C
#define PORT_LOGIC_SPEED_CHANGE (0x1 << 17)
#define PORT_LOGIC_LINK_WIDTH_MASK (0x1ff << 8)
#define PORT_LOGIC_LINK_WIDTH_1_LANES (0x1 << 8)
#define PORT_LOGIC_LINK_WIDTH_2_LANES (0x2 << 8)
#define PORT_LOGIC_LINK_WIDTH_4_LANES (0x4 << 8)
#define PCIE_MSI_ADDR_LO 0x820
#define PCIE_MSI_ADDR_HI 0x824
#define PCIE_MSI_INTR0_ENABLE 0x828
#define PCIE_MSI_INTR0_MASK 0x82C
#define PCIE_MSI_INTR0_STATUS 0x830
#define PCIE_ATU_VIEWPORT 0x900
#define PCIE_ATU_REGION_INBOUND (0x1 << 31)
#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31)
#define PCIE_ATU_REGION_INDEX1 (0x1 << 0)
#define PCIE_ATU_REGION_INDEX0 (0x0 << 0)
#define PCIE_ATU_CR1 0x904
#define PCIE_ATU_TYPE_MEM (0x0 << 0)
#define PCIE_ATU_TYPE_IO (0x2 << 0)
#define PCIE_ATU_TYPE_CFG0 (0x4 << 0)
#define PCIE_ATU_TYPE_CFG1 (0x5 << 0)
#define PCIE_ATU_CR2 0x908
#define PCIE_ATU_ENABLE (0x1 << 31)
#define PCIE_ATU_BAR_MODE_ENABLE (0x1 << 30)
#define PCIE_ATU_LOWER_BASE 0x90C
#define PCIE_ATU_UPPER_BASE 0x910
#define PCIE_ATU_LIMIT 0x914
#define PCIE_ATU_LOWER_TARGET 0x918
#define PCIE_ATU_BUS(x) (((x) & 0xff) << 24)
#define PCIE_ATU_DEV(x) (((x) & 0x1f) << 19)
#define PCIE_ATU_FUNC(x) (((x) & 0x7) << 16)
#define PCIE_ATU_UPPER_TARGET 0x91C
static struct hw_pci dw_pci;
static unsigned long global_io_offset;
static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
{
BUG_ON(!sys->private_data);
return sys->private_data;
}
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
{
*val = readl(addr);
if (size == 1)
*val = (*val >> (8 * (where & 3))) & 0xff;
else if (size == 2)
*val = (*val >> (8 * (where & 3))) & 0xffff;
else if (size != 4)
return PCIBIOS_BAD_REGISTER_NUMBER;
return PCIBIOS_SUCCESSFUL;
}
int dw_pcie_cfg_write(void __iomem *addr, int where, int size, u32 val)
{
if (size == 4)
writel(val, addr);
else if (size == 2)
writew(val, addr + (where & 2));
else if (size == 1)
writeb(val, addr + (where & 3));
else
return PCIBIOS_BAD_REGISTER_NUMBER;
return PCIBIOS_SUCCESSFUL;
}
static inline void dw_pcie_readl_rc(struct pcie_port *pp, u32 reg, u32 *val)
{
if (pp->ops->readl_rc)
pp->ops->readl_rc(pp, pp->dbi_base + reg, val);
else
*val = readl(pp->dbi_base + reg);
}
static inline void dw_pcie_writel_rc(struct pcie_port *pp, u32 val, u32 reg)
{
if (pp->ops->writel_rc)
pp->ops->writel_rc(pp, val, pp->dbi_base + reg);
else
writel(val, pp->dbi_base + reg);
}
static int dw_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
u32 *val)
{
int ret;
if (pp->ops->rd_own_conf)
ret = pp->ops->rd_own_conf(pp, where, size, val);
else
ret = dw_pcie_cfg_read(pp->dbi_base + (where & ~0x3), where,
size, val);
return ret;
}
static int dw_pcie_wr_own_conf(struct pcie_port *pp, int where, int size,
u32 val)
{
int ret;
if (pp->ops->wr_own_conf)
ret = pp->ops->wr_own_conf(pp, where, size, val);
else
ret = dw_pcie_cfg_write(pp->dbi_base + (where & ~0x3), where,
size, val);
return ret;
}
static struct irq_chip dw_msi_irq_chip = {
.name = "PCI-MSI",
.irq_enable = unmask_msi_irq,
.irq_disable = mask_msi_irq,
.irq_mask = mask_msi_irq,
.irq_unmask = unmask_msi_irq,
};
/* MSI int handler */
irqreturn_t dw_handle_msi_irq(struct pcie_port *pp)
{
unsigned long val;
int i, pos, irq;
irqreturn_t ret = IRQ_NONE;
for (i = 0; i < MAX_MSI_CTRLS; i++) {
dw_pcie_rd_own_conf(pp, PCIE_MSI_INTR0_STATUS + i * 12, 4,
(u32 *)&val);
if (val) {
ret = IRQ_HANDLED;
pos = 0;
while ((pos = find_next_bit(&val, 32, pos)) != 32) {
irq = irq_find_mapping(pp->irq_domain,
i * 32 + pos);
dw_pcie_wr_own_conf(pp,
PCIE_MSI_INTR0_STATUS + i * 12,
4, 1 << pos);
generic_handle_irq(irq);
pos++;
}
}
}
return ret;
}
void dw_pcie_msi_init(struct pcie_port *pp)
{
pp->msi_data = __get_free_pages(GFP_KERNEL, 0);
/* program the msi_data */
dw_pcie_wr_own_conf(pp, PCIE_MSI_ADDR_LO, 4,
virt_to_phys((void *)pp->msi_data));
dw_pcie_wr_own_conf(pp, PCIE_MSI_ADDR_HI, 4, 0);
}
static int find_valid_pos0(struct pcie_port *pp, int msgvec, int pos, int *pos0)
{
int flag = 1;
do {
pos = find_next_zero_bit(pp->msi_irq_in_use,
MAX_MSI_IRQS, pos);
/*if you have reached to the end then get out from here.*/
if (pos == MAX_MSI_IRQS)
return -ENOSPC;
/*
* Check if this position is at correct offset.nvec is always a
* power of two. pos0 must be nvec bit aligned.
*/
if (pos % msgvec)
pos += msgvec - (pos % msgvec);
else
flag = 0;
} while (flag);
*pos0 = pos;
return 0;
}
2014-07-21 16:58:42 +00:00
static void dw_pcie_msi_clear_irq(struct pcie_port *pp, int irq)
{
unsigned int res, bit, val;
res = (irq / 32) * 12;
bit = irq % 32;
dw_pcie_rd_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, &val);
val &= ~(1 << bit);
dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, val);
}
static void clear_irq_range(struct pcie_port *pp, unsigned int irq_base,
unsigned int nvec, unsigned int pos)
{
2014-07-21 16:58:42 +00:00
unsigned int i;
for (i = 0; i < nvec; i++) {
irq_set_msi_desc_off(irq_base, i, NULL);
clear_bit(pos + i, pp->msi_irq_in_use);
/* Disable corresponding interrupt on MSI controller */
2014-07-21 16:58:42 +00:00
if (pp->ops->msi_clear_irq)
pp->ops->msi_clear_irq(pp, pos + i);
else
dw_pcie_msi_clear_irq(pp, pos + i);
}
}
2014-07-21 16:58:42 +00:00
static void dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
{
unsigned int res, bit, val;
res = (irq / 32) * 12;
bit = irq % 32;
dw_pcie_rd_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, &val);
val |= 1 << bit;
dw_pcie_wr_own_conf(pp, PCIE_MSI_INTR0_ENABLE + res, 4, val);
}
static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
{
2014-07-21 16:58:42 +00:00
int irq, pos0, pos1, i;
struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
pos0 = find_first_zero_bit(pp->msi_irq_in_use,
MAX_MSI_IRQS);
if (pos0 % no_irqs) {
if (find_valid_pos0(pp, no_irqs, pos0, &pos0))
goto no_valid_irq;
}
if (no_irqs > 1) {
pos1 = find_next_bit(pp->msi_irq_in_use,
MAX_MSI_IRQS, pos0);
/* there must be nvec number of consecutive free bits */
while ((pos1 - pos0) < no_irqs) {
if (find_valid_pos0(pp, no_irqs, pos1, &pos0))
goto no_valid_irq;
pos1 = find_next_bit(pp->msi_irq_in_use,
MAX_MSI_IRQS, pos0);
}
}
irq = irq_find_mapping(pp->irq_domain, pos0);
if (!irq)
goto no_valid_irq;
/*
* irq_create_mapping (called from dw_pcie_host_init) pre-allocates
* descs so there is no need to allocate descs here. We can therefore
* assume that if irq_find_mapping above returns non-zero, then the
* descs are also successfully allocated.
*/
for (i = 0; i < no_irqs; i++) {
if (irq_set_msi_desc_off(irq, i, desc) != 0) {
clear_irq_range(pp, irq, i, pos0);
goto no_valid_irq;
}
set_bit(pos0 + i, pp->msi_irq_in_use);
/*Enable corresponding interrupt in MSI interrupt controller */
2014-07-21 16:58:42 +00:00
if (pp->ops->msi_set_irq)
pp->ops->msi_set_irq(pp, pos0 + i);
else
dw_pcie_msi_set_irq(pp, pos0 + i);
}
*pos = pos0;
return irq;
no_valid_irq:
*pos = pos0;
return -ENOSPC;
}
static void clear_irq(unsigned int irq)
{
unsigned int pos, nvec;
struct msi_desc *msi;
struct pcie_port *pp;
struct irq_data *data = irq_get_irq_data(irq);
/* get the port structure */
msi = irq_data_get_msi(data);
pp = sys_to_pcie(msi->dev->bus->sysdata);
/* undo what was done in assign_irq */
pos = data->hwirq;
nvec = 1 << msi->msi_attrib.multiple;
clear_irq_range(pp, irq, nvec, pos);
/* all irqs cleared; reset attributes */
msi->irq = 0;
msi->msi_attrib.multiple = 0;
}
static int dw_msi_setup_irq(struct msi_chip *chip, struct pci_dev *pdev,
struct msi_desc *desc)
{
int irq, pos, msgvec;
u16 msg_ctr;
struct msi_msg msg;
struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
pci_read_config_word(pdev, desc->msi_attrib.pos+PCI_MSI_FLAGS,
&msg_ctr);
msgvec = (msg_ctr&PCI_MSI_FLAGS_QSIZE) >> 4;
if (msgvec == 0)
msgvec = (msg_ctr & PCI_MSI_FLAGS_QMASK) >> 1;
if (msgvec > 5)
msgvec = 0;
irq = assign_irq((1 << msgvec), desc, &pos);
if (irq < 0)
return irq;
/*
* write_msi_msg() will update PCI_MSI_FLAGS so there is
* no need to explicitly call pci_write_config_word().
*/
desc->msi_attrib.multiple = msgvec;
if (pp->ops->get_msi_addr)
msg.address_lo = pp->ops->get_msi_addr(pp);
2014-07-21 16:58:42 +00:00
else
msg.address_lo = virt_to_phys((void *)pp->msi_data);
msg.address_hi = 0x0;
msg.data = pos;
write_msi_msg(irq, &msg);
return 0;
}
static void dw_msi_teardown_irq(struct msi_chip *chip, unsigned int irq)
{
clear_irq(irq);
}
static struct msi_chip dw_pcie_msi_chip = {
.setup_irq = dw_msi_setup_irq,
.teardown_irq = dw_msi_teardown_irq,
};
int dw_pcie_link_up(struct pcie_port *pp)
{
if (pp->ops->link_up)
return pp->ops->link_up(pp);
else
return 0;
}
static int dw_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
irq_hw_number_t hwirq)
{
irq_set_chip_and_handler(irq, &dw_msi_irq_chip, handle_simple_irq);
irq_set_chip_data(irq, domain->host_data);
set_irq_flags(irq, IRQF_VALID);
return 0;
}
static const struct irq_domain_ops msi_domain_ops = {
.map = dw_pcie_msi_map,
};
int __init dw_pcie_host_init(struct pcie_port *pp)
{
struct device_node *np = pp->dev->of_node;
struct platform_device *pdev = to_platform_device(pp->dev);
struct of_pci_range range;
struct of_pci_range_parser parser;
struct resource *cfg_res;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
u32 val, na, ns;
const __be32 *addrp;
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
int i, index, ret;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
/* Find the address cell size and the number of cells in order to get
* the untranslated address.
*/
of_property_read_u32(np, "#address-cells", &na);
ns = of_n_size_cells(np);
cfg_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
if (cfg_res) {
pp->cfg0_size = resource_size(cfg_res)/2;
pp->cfg1_size = resource_size(cfg_res)/2;
pp->cfg0_base = cfg_res->start;
pp->cfg1_base = cfg_res->start + pp->cfg0_size;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
/* Find the untranslated configuration space address */
index = of_property_match_string(np, "reg-names", "config");
addrp = of_get_address(np, index, NULL, NULL);
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
pp->cfg0_mod_base = of_read_number(addrp, ns);
pp->cfg1_mod_base = pp->cfg0_mod_base + pp->cfg0_size;
} else {
dev_err(pp->dev, "missing *config* reg space\n");
}
if (of_pci_range_parser_init(&parser, np)) {
dev_err(pp->dev, "missing ranges property\n");
return -EINVAL;
}
/* Get the I/O and memory ranges from DT */
for_each_of_pci_range(&parser, &range) {
unsigned long restype = range.flags & IORESOURCE_TYPE_BITS;
if (restype == IORESOURCE_IO) {
of_pci_range_to_resource(&range, np, &pp->io);
pp->io.name = "I/O";
pp->io.start = max_t(resource_size_t,
PCIBIOS_MIN_IO,
range.pci_addr + global_io_offset);
pp->io.end = min_t(resource_size_t,
IO_SPACE_LIMIT,
range.pci_addr + range.size
+ global_io_offset - 1);
pp->io_size = resource_size(&pp->io);
pp->io_bus_addr = range.pci_addr;
pp->io_base = range.cpu_addr;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
/* Find the untranslated IO space address */
pp->io_mod_base = of_read_number(parser.range -
parser.np + na, ns);
}
if (restype == IORESOURCE_MEM) {
of_pci_range_to_resource(&range, np, &pp->mem);
pp->mem.name = "MEM";
pp->mem_size = resource_size(&pp->mem);
pp->mem_bus_addr = range.pci_addr;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
/* Find the untranslated MEM space address */
pp->mem_mod_base = of_read_number(parser.range -
parser.np + na, ns);
}
if (restype == 0) {
of_pci_range_to_resource(&range, np, &pp->cfg);
pp->cfg0_size = resource_size(&pp->cfg)/2;
pp->cfg1_size = resource_size(&pp->cfg)/2;
pp->cfg0_base = pp->cfg.start;
pp->cfg1_base = pp->cfg.start + pp->cfg0_size;
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
/* Find the untranslated configuration space address */
pp->cfg0_mod_base = of_read_number(parser.range -
parser.np + na, ns);
pp->cfg1_mod_base = pp->cfg0_mod_base +
pp->cfg0_size;
}
}
ret = of_pci_parse_bus_range(np, &pp->busn);
if (ret < 0) {
pp->busn.name = np->name;
pp->busn.start = 0;
pp->busn.end = 0xff;
pp->busn.flags = IORESOURCE_BUS;
dev_dbg(pp->dev, "failed to parse bus-range property: %d, using default %pR\n",
ret, &pp->busn);
}
if (!pp->dbi_base) {
pp->dbi_base = devm_ioremap(pp->dev, pp->cfg.start,
resource_size(&pp->cfg));
if (!pp->dbi_base) {
dev_err(pp->dev, "error with ioremap\n");
return -ENOMEM;
}
}
pp->mem_base = pp->mem.start;
if (!pp->va_cfg0_base) {
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
pp->va_cfg0_base = devm_ioremap(pp->dev, pp->cfg0_base,
pp->cfg0_size);
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
if (!pp->va_cfg0_base) {
dev_err(pp->dev, "error with ioremap in function\n");
return -ENOMEM;
}
}
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
if (!pp->va_cfg1_base) {
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
pp->va_cfg1_base = devm_ioremap(pp->dev, pp->cfg1_base,
pp->cfg1_size);
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
if (!pp->va_cfg1_base) {
dev_err(pp->dev, "error with ioremap\n");
return -ENOMEM;
}
}
if (of_property_read_u32(np, "num-lanes", &pp->lanes)) {
dev_err(pp->dev, "Failed to parse the number of lanes\n");
return -EINVAL;
}
if (IS_ENABLED(CONFIG_PCI_MSI)) {
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
if (!pp->ops->msi_host_init) {
pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
MAX_MSI_IRQS, &msi_domain_ops,
&dw_pcie_msi_chip);
if (!pp->irq_domain) {
dev_err(pp->dev, "irq domain init failed\n");
return -ENXIO;
}
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
for (i = 0; i < MAX_MSI_IRQS; i++)
irq_create_mapping(pp->irq_domain, i);
} else {
ret = pp->ops->msi_host_init(pp, &dw_pcie_msi_chip);
if (ret < 0)
return ret;
}
}
if (pp->ops->host_init)
pp->ops->host_init(pp);
dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
/* program correct class for RC */
dw_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI);
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val);
val |= PORT_LOGIC_SPEED_CHANGE;
dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
dw_pci.nr_controllers = 1;
dw_pci.private_data = (void **)&pp;
pci_common_init_dev(pp->dev, &dw_pci);
#ifdef CONFIG_PCI_DOMAINS
dw_pci.domain++;
#endif
return 0;
}
static void dw_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev)
{
/* Program viewport 0 : OUTBOUND : CFG0 */
dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0,
PCIE_ATU_VIEWPORT);
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
dw_pcie_writel_rc(pp, pp->cfg0_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->cfg0_mod_base >> 32), PCIE_ATU_UPPER_BASE);
dw_pcie_writel_rc(pp, pp->cfg0_mod_base + pp->cfg0_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG0, PCIE_ATU_CR1);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
static void dw_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev)
{
/* Program viewport 1 : OUTBOUND : CFG1 */
dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1,
PCIE_ATU_VIEWPORT);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG1, PCIE_ATU_CR1);
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
dw_pcie_writel_rc(pp, pp->cfg1_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->cfg1_mod_base >> 32), PCIE_ATU_UPPER_BASE);
dw_pcie_writel_rc(pp, pp->cfg1_mod_base + pp->cfg1_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp)
{
/* Program viewport 0 : OUTBOUND : MEM */
dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0,
PCIE_ATU_VIEWPORT);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, PCIE_ATU_CR1);
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
dw_pcie_writel_rc(pp, pp->mem_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->mem_mod_base >> 32), PCIE_ATU_UPPER_BASE);
dw_pcie_writel_rc(pp, pp->mem_mod_base + pp->mem_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, pp->mem_bus_addr, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, upper_32_bits(pp->mem_bus_addr),
PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp)
{
/* Program viewport 1 : OUTBOUND : IO */
dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1,
PCIE_ATU_VIEWPORT);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_IO, PCIE_ATU_CR1);
PCI: designware: Program ATU with untranslated address In DRA7, the CPU sees 32-bit addresses, but the PCIe controller can see only 28-bit addresses. So whenever the CPU issues a read/write request, the 4 most significant bits are used by L3 to determine the target controller. For example, the CPU reserves [mem 0x20000000-0x2fffffff] for the PCIe controller but the PCIe controller will see only [0x00000000-0x0fffffff]. For programming the outbound translation window the *base* should be programmed as 0x00000000. Whenever we try to write to, e.g., 0x20000000, it will be translated to whatever we have programmed in the translation window with base as 0x00000000. This is needed when the dt node is modelled something like this: axi { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; ranges = <0x0 0x20000000 0x10000000 // 28-bit bus 0x51000000 0x51000000 0x3000>; pcie@51000000 { reg = <0x1000 0x2000>, <0x51002000 0x14c>, <0x51000000 0x2000>; reg-names = "config", "ti_conf", "rc_dbics"; #address-cells = <3>; #size-cells = <2>; ranges = <0x81000000 0 0 0x03000 0 0x00010000 0x82000000 0 0x20013000 0x13000 0 0xffed000>; }; }; Here the CPU address for configuration space is 0x20013000 and the controller address for configuration space is 0x13000. The controller address should be used while programming the ATU (in order for translation to happen properly in DRA7xx). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mohit Kumar <mohit.kumar@st.com> Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Cc: Jingoo Han <jg1.han@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Arnd Bergmann <arnd@arndb.de>
2014-07-17 09:00:41 +00:00
dw_pcie_writel_rc(pp, pp->io_mod_base, PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, (pp->io_mod_base >> 32), PCIE_ATU_UPPER_BASE);
dw_pcie_writel_rc(pp, pp->io_mod_base + pp->io_size - 1,
PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, pp->io_bus_addr, PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, upper_32_bits(pp->io_bus_addr),
PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
}
static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
u32 devfn, int where, int size, u32 *val)
{
int ret = PCIBIOS_SUCCESSFUL;
u32 address, busdev;
busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) |
PCIE_ATU_FUNC(PCI_FUNC(devfn));
address = where & ~0x3;
if (bus->parent->number == pp->root_bus_nr) {
dw_pcie_prog_viewport_cfg0(pp, busdev);
ret = dw_pcie_cfg_read(pp->va_cfg0_base + address, where, size,
val);
dw_pcie_prog_viewport_mem_outbound(pp);
} else {
dw_pcie_prog_viewport_cfg1(pp, busdev);
ret = dw_pcie_cfg_read(pp->va_cfg1_base + address, where, size,
val);
dw_pcie_prog_viewport_io_outbound(pp);
}
return ret;
}
static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
u32 devfn, int where, int size, u32 val)
{
int ret = PCIBIOS_SUCCESSFUL;
u32 address, busdev;
busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) |
PCIE_ATU_FUNC(PCI_FUNC(devfn));
address = where & ~0x3;
if (bus->parent->number == pp->root_bus_nr) {
dw_pcie_prog_viewport_cfg0(pp, busdev);
ret = dw_pcie_cfg_write(pp->va_cfg0_base + address, where, size,
val);
dw_pcie_prog_viewport_mem_outbound(pp);
} else {
dw_pcie_prog_viewport_cfg1(pp, busdev);
ret = dw_pcie_cfg_write(pp->va_cfg1_base + address, where, size,
val);
dw_pcie_prog_viewport_io_outbound(pp);
}
return ret;
}
static int dw_pcie_valid_config(struct pcie_port *pp,
struct pci_bus *bus, int dev)
{
/* If there is no link, then there is no device */
if (bus->number != pp->root_bus_nr) {
if (!dw_pcie_link_up(pp))
return 0;
}
/* access only one slot on each root port */
if (bus->number == pp->root_bus_nr && dev > 0)
return 0;
/*
* do not read more than one device on the bus directly attached
* to RC's (Virtual Bridge's) DS side.
*/
if (bus->primary == pp->root_bus_nr && dev > 0)
return 0;
return 1;
}
static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
int size, u32 *val)
{
struct pcie_port *pp = sys_to_pcie(bus->sysdata);
int ret;
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
*val = 0xffffffff;
return PCIBIOS_DEVICE_NOT_FOUND;
}
if (bus->number != pp->root_bus_nr)
if (pp->ops->rd_other_conf)
ret = pp->ops->rd_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_rd_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_rd_own_conf(pp, where, size, val);
return ret;
}
static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
int where, int size, u32 val)
{
struct pcie_port *pp = sys_to_pcie(bus->sysdata);
int ret;
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
return PCIBIOS_DEVICE_NOT_FOUND;
if (bus->number != pp->root_bus_nr)
if (pp->ops->wr_other_conf)
ret = pp->ops->wr_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_wr_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_wr_own_conf(pp, where, size, val);
return ret;
}
static struct pci_ops dw_pcie_ops = {
.read = dw_pcie_rd_conf,
.write = dw_pcie_wr_conf,
};
static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
{
struct pcie_port *pp;
pp = sys_to_pcie(sys);
if (global_io_offset < SZ_1M && pp->io_size > 0) {
sys->io_offset = global_io_offset - pp->io_bus_addr;
pci_ioremap_io(global_io_offset, pp->io_base);
global_io_offset += SZ_64K;
pci_add_resource_offset(&sys->resources, &pp->io,
sys->io_offset);
}
sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
pci_add_resource(&sys->resources, &pp->busn);
return 1;
}
static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
{
struct pci_bus *bus;
struct pcie_port *pp = sys_to_pcie(sys);
pp->root_bus_nr = sys->busnr;
bus = pci_create_root_bus(pp->dev, sys->busnr,
&dw_pcie_ops, sys, &sys->resources);
if (!bus)
return NULL;
pci_scan_child_bus(bus);
PCI: designware: Add support for v3.65 hardware The Keystone PCI controller is based on v3.65 DesignWare hardware. This version differs from newer versions of the hardware in functional areas discussed below that make it necessary to change dw_pcie_host_init() to support v3.65 based PCI controller. 1. No support for ATU port. Any ATU-specific resource handling code is to be bypassed for v3.65 h/w. 2. MSI controller uses application space to implement MSI and 32 MSI interrupts are multiplexed over 8 IRQs to the host. Hence the code to process MSI IRQ needs to be different. This patch allows platform driver to provide its own irq_domain_ops ptr to irq_domain_add_linear() through an API callback from the DesignWare core driver. 3. MSI interrupt generation requires EP to write to the RC's application register. So enhance the driver to allow setup of inbound access to MSI IRQ register as a post scan bus API callback. Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pratyush Anand <pratyush.anand@st.com> Acked-by: Mohit KUMAR <mohit.kumar@st.com> Acked-by: Jingoo Han <jg1.han@samsung.com> CC: Santosh Shilimkar <santosh.shilimkar@ti.com> CC: Russell King <linux@arm.linux.org.uk> CC: Grant Likely <grant.likely@linaro.org> CC: Rob Herring <robh+dt@kernel.org> CC: Jingoo Han <jg1.han@samsung.com> CC: Richard Zhu <r65037@freescale.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Marek Vasut <marex@denx.de> CC: Arnd Bergmann <arnd@arndb.de> CC: Pawel Moll <pawel.moll@arm.com> CC: Mark Rutland <mark.rutland@arm.com> CC: Ian Campbell <ijc+devicetree@hellion.org.uk> CC: Kumar Gala <galak@codeaurora.org> CC: Randy Dunlap <rdunlap@infradead.org> CC: Grant Likely <grant.likely@linaro.org>
2014-07-23 18:54:51 +00:00
if (bus && pp->ops->scan_bus)
pp->ops->scan_bus(pp);
return bus;
}
static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
int irq;
irq = of_irq_parse_and_map_pci(dev, slot, pin);
if (!irq)
irq = pp->irq;
return irq;
}
static void dw_pcie_add_bus(struct pci_bus *bus)
{
if (IS_ENABLED(CONFIG_PCI_MSI)) {
struct pcie_port *pp = sys_to_pcie(bus->sysdata);
dw_pcie_msi_chip.dev = pp->dev;
bus->msi = &dw_pcie_msi_chip;
}
}
static struct hw_pci dw_pci = {
.setup = dw_pcie_setup,
.scan = dw_pcie_scan_bus,
.map_irq = dw_pcie_map_irq,
.add_bus = dw_pcie_add_bus,
};
void dw_pcie_setup_rc(struct pcie_port *pp)
{
u32 val;
u32 membase;
u32 memlimit;
/* set the number of lanes */
dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL, &val);
val &= ~PORT_LINK_MODE_MASK;
switch (pp->lanes) {
case 1:
val |= PORT_LINK_MODE_1_LANES;
break;
case 2:
val |= PORT_LINK_MODE_2_LANES;
break;
case 4:
val |= PORT_LINK_MODE_4_LANES;
break;
}
dw_pcie_writel_rc(pp, val, PCIE_PORT_LINK_CONTROL);
/* set link width speed control register */
dw_pcie_readl_rc(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, &val);
val &= ~PORT_LOGIC_LINK_WIDTH_MASK;
switch (pp->lanes) {
case 1:
val |= PORT_LOGIC_LINK_WIDTH_1_LANES;
break;
case 2:
val |= PORT_LOGIC_LINK_WIDTH_2_LANES;
break;
case 4:
val |= PORT_LOGIC_LINK_WIDTH_4_LANES;
break;
}
dw_pcie_writel_rc(pp, val, PCIE_LINK_WIDTH_SPEED_CONTROL);
/* setup RC BARs */
dw_pcie_writel_rc(pp, 0x00000004, PCI_BASE_ADDRESS_0);
dw_pcie_writel_rc(pp, 0x00000000, PCI_BASE_ADDRESS_1);
/* setup interrupt pins */
dw_pcie_readl_rc(pp, PCI_INTERRUPT_LINE, &val);
val &= 0xffff00ff;
val |= 0x00000100;
dw_pcie_writel_rc(pp, val, PCI_INTERRUPT_LINE);
/* setup bus numbers */
dw_pcie_readl_rc(pp, PCI_PRIMARY_BUS, &val);
val &= 0xff000000;
val |= 0x00010100;
dw_pcie_writel_rc(pp, val, PCI_PRIMARY_BUS);
/* setup memory base, memory limit */
membase = ((u32)pp->mem_base & 0xfff00000) >> 16;
memlimit = (pp->mem_size + (u32)pp->mem_base) & 0xfff00000;
val = memlimit | membase;
dw_pcie_writel_rc(pp, val, PCI_MEMORY_BASE);
/* setup command register */
dw_pcie_readl_rc(pp, PCI_COMMAND, &val);
val &= 0xffff0000;
val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY |
PCI_COMMAND_MASTER | PCI_COMMAND_SERR;
dw_pcie_writel_rc(pp, val, PCI_COMMAND);
}
MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>");
MODULE_DESCRIPTION("Designware PCIe host controller driver");
MODULE_LICENSE("GPL v2");