drm-intel-next-2014-01-10:
- final bits for runtime D3 on Haswell from Paul (now enabled fully)
- parse the backlight modulation freq information in the VBT from Jani
(but not yet used)
- more watermark improvements from Ville for ilk-ivb and bdw
- bugfixes for fastboot from Jesse
- watermark fix for i830M (but not yet everything)
- vlv vga hotplug w/a (Imre)
- piles of other small improvements, cleanups and fixes all over
Note that the pull request includes a backmerge of the last drm-fixes
pulled into Linus' tree - things where getting a bit too messy. So the
shortlog also contains a bunch of patches from Linus tree. Please yell if
you want me to frob it for you a bit.
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (609 commits)
drm/i915/bdw: make sure south port interrupts are enabled properly v2
drm/i915: Include more information in disabled hotplug interrupt warning
drm/i915: Only complain about a rogue hotplug IRQ after disabling
drm/i915: Only WARN about a stuck hotplug irq ONCE
drm/i915: s/hotplugt_status_gen4/hotplug_status_g4x/
Pull clock fixes from Mike Turquette:
"Late fixes for clock drivers. All of these fixes are for user-visible
regressions, typically boot failures or other unsafe system
configuration that causes badness"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: clk-divider: fix divisor > 255 bug
clk: exynos: File scope reg_save array should depend on PM_SLEEP
clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg clock
ARM: dts: exynos5250: Fix MDMA0 clock number
clk: samsung: exynos5250: Add MDMA0 clocks
clk: samsung: exynos5250: Fix ACP gate register offset
clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
clk: samsung: exynos4: Correct SRC_MFC register
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for Renesas platforms to fixup DMA masks (this started
causing errors once the DMA API added checks for valid masks in 3.13)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
Pull ARM fixes from Russell King:
"Another set of small fixes for ARM, covering various areas.
Laura fixed a long standing issue with virt_addr_valid() failing to
handle holes in memory. Steve found a problem with dcache flushing
for compound pages. I fixed another bug in footbridge stuff causing
time to tick slowly, and also a problem with the AES code which can
cause linker errors.
A patch from Rob which fixes Xen problems induced by a lack of
consistency in our naming of ioremap_cache() - which thankfully has
very few users"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7933/1: rename ioremap_cached to ioremap_cache
ARM: fix "bad mode in ... handler" message for undefined instructions
CRYPTO: Fix more AES build errors
ARM: 7931/1: Correct virt_addr_valid
ARM: 7923/1: mm: fix dcache flush logic for compound high pages
ARM: fix footbridge clockevent device
ioremap_cache is more aligned with other architectures.
There are only 2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64:
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Building a multi-arch kernel results in:
arch/arm/crypto/built-in.o: In function `aesbs_xts_decrypt':
sha1_glue.c:(.text+0x15c8): undefined reference to `bsaes_xts_decrypt'
arch/arm/crypto/built-in.o: In function `aesbs_xts_encrypt':
sha1_glue.c:(.text+0x1664): undefined reference to `bsaes_xts_encrypt'
arch/arm/crypto/built-in.o: In function `aesbs_ctr_encrypt':
sha1_glue.c:(.text+0x184c): undefined reference to `bsaes_ctr32_encrypt_blocks'
arch/arm/crypto/built-in.o: In function `aesbs_cbc_decrypt':
sha1_glue.c:(.text+0x19b4): undefined reference to `bsaes_cbc_encrypt'
This code is already runtime-conditional on NEON being supported, so
there's no point compiling it out depending on the minimum build
architecture.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From Simon Horman:
Third Round of Renesas ARM based SoC Fixes for v3.13
* sh7372 (SH-Mobile AP4) based Mackerel board
r8a773a0 (SH-Mobile AG5) based kzm9g board
r8a7740 (R-Mobile A1) based Armadillo board
- Correct coherent DMA mask
This resolves regressions introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* tag 'renesas-fixes3-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
Signed-off-by: Olof Johansson <olof@lixom.net>
Due to incorrect clock specified in MDMA0 node, using MDMA0 controller
could cause system failures, due to wrong clock being controlled. This
patch fixes this by specifying correct clock.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Corrected commit message and description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The definition of virt_addr_valid is that virt_addr_valid should
return true if and only if virt_to_page returns a valid pointer.
The current definition of virt_addr_valid only checks against the
virtual address range. There's no guarantee that just because a
virtual address falls bewteen PAGE_OFFSET and high_memory the
associated physical memory has a valid backing struct page. Follow
the example of other architectures and convert to pfn_valid to
verify that the virtual address is actually valid. The check for
an address between PAGE_OFFSET and high_memory is still necessary
as vmalloc/highmem addresses are not valid with virt_to_page.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When given a compound high page, __flush_dcache_page will only flush
the first page of the compound page repeatedly rather than the entire
set of constituent pages.
This error was introduced by:
0b19f93 ARM: mm: Add support for flushing HugeTLB pages.
This patch corrects the logic such that all constituent pages are now
flushed.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clockevents code was being told that the footbridge clock event
device ticks at 16x the rate which it actually does. This leads to
timekeeping problems since it allows the clocksource to wrap before
the kernel notices. Fix this by using the correct clock.
Fixes: 4e8d76373c ("ARM: footbridge: convert to clockevents/clocksource")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: <stable@vger.kernel.org>
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1e
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Fixes: 7dedd34694 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
From Simon Horman:
Renesas ARM based SoC fixes for v3.13
* r8a7790 (R-Car H1) SoC
- Correct GPIO resources in DT.
This problem has been present since GPIOs were added to the r8a7790 SoC
by f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller
devices to device tree") in v3.12-rc1.
* irqchip renesas-intc-irqpin
- Correct register bitfield shift calculation
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1
* Lager board
- Do not build the phy fixup unless CONFIG_PHYLIB is enabled
This problem was introduced by 48c8b96f21
* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
scratch pages.
- Fix block API header for ARM32 and ARM64 to have proper layout
- On ARM when mapping guests, stick on PTE_SPECIAL
- When using SWIOTLB under ARM, don't call swiotlb functions twice
- When unmapping guests memory and if we fail, don't return pages which
failed to be unmapped.
- Grant driver was using the wrong address on ARM.
* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Seperate the auto-translate logic properly (v2)
xen/block: Correctly define structures in public headers on ARM32 and ARM64
arm: xen: foreign mapping PTEs are special.
xen/arm64: do not call the swiotlb functions twice
xen: privcmd: do not return pages which we have failed to unmap
XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn
I accidentally removed some mux code for omap4 that I thought was
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.
* tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (439 commits)
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
+Linux 3.13-rc4
The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.
Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: William Towle <william.towle@codethink.co.uk>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4dcfa60071
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch
asoc-simple-card asoc-simple-card.0: \
Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 22ceeee16e ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit e30b06f4d5 (ARM: OMAP2+: Remove
legacy mux code for display.c) removed non-DT DSI and HDMI pinmuxing.
However, DSI pinmuxing is still needed, and removing that caused DSI
displays not to work.
This reverts the DSI parts of the commit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: tegra: powergate driver changes
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
Add tegra_io_rail_power_off() and tegra_io_rail_power_on() functions to
put IO rails into or out of deep powerdown mode, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A separate register is used to remove the clamps for the GPU on
Tegra124. In order to be able to use the same API, special-case
this particular partition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Three new gates have been added for Tegra124: SOR, VIC and IRAM. In
addition, PCIe and SATA gates are again supported, like on Tegra20 and
Tegra30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Drivers can use the tegra_powergate_remove_clamping() API during
initialization. In order to allow such drivers to be built as modules,
export the symbol.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This function can be used by drivers, which in turn may be built as
modules. Export the symbol so it is available to modules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This matches the name of the powergate as listed in the TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Some of the powergate code uses unusual spacing around == and has a tab
instead of a space before an opening parenthesis.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit
4178bac ARM: call of_clk_init from default time_init handler
added implicit call to of_clk_init() from default time_init callback,
but it did not change platforms calling it from other callbacks, despite
of not having custom time_init callbacks. This caused double clock
initialization on such platforms, leading to boot failures. An example
of such platform is mach-s3c64xx.
This patch fixes boot failure on s3c64xx by dropping custom init_irq
callback, which had a call to of_clk_init() and moving system reset
initialization to init_machine callback. This allows us to have
clocks initialized properly without a need to have custom init_time or
init_irq callbacks.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"This resolves some further issues with the dma mask changes on ARM
which have been found by TI and others, and also some corner cases
with the updates to the virtual to physical address translations.
Konstantin also found some problems with the unwinder, which now
performs tighter verification that the stack is valid while unwinding"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix asm/memory.h build error
ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
ARM: 7913/1: fix framepointer check in unwind_frame
ARM: 7912/1: check stack pointer in get_wchan
ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
ARM: 7908/1: mm: Fix the arm_dma_limit calculation
ARM: another fix for the DMA mapping checks
Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:
In file included from arch/arm/include/asm/page.h:163:0,
from include/linux/mm_types.h:16,
from include/linux/sched.h:24,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)
Fixes: ca5a45c06c ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Allwinner A31 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A31 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 uses the ARM GIC as its internal interrupts controller. The
GIC can work on several interrupt triggers, and the A20 was actually setting it
up to use a rising edge as a trigger, while it was actually a level high
trigger, leading to some interrupts that would be completely ignored if the
edge was missed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org #3.12+
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a missing break to the switch in tegra_init_fuse() which determines
which SoC the code is running on. This prevents the Tegra30+ fuse
handling code from running on Tegra20.
Fixes: 3bd1ae57f7 ("ARM: tegra: add fuses as device randomness")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs. We put SDRAM in selfresh mode before watchdog
reset, removing potential freezes.
Without this patch PXA270-based ICP DAS LP-8x4x hangs after up to 40
reboots. With this patch it has successfully rebooted 500 times.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
When converting from tosa-keyboard driver to matrix keyboard, tosa keys
received extra 1 column shift. Replace that with correct values to make
keyboard work again.
Fixes: f69a6548c9 ('[ARM] pxa/tosa: make use of the matrix keypad driver')
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
