According to both the old acpi_igd_opregion_spec_0.pdf and the newer
skl_opregion_rev0p5.pdf opregion specification documents, if a driver
handles hotplug events itself, it should set the opregion CHPD field to
1 to indicate this and the firmware should respond to this by no longer
sending ACPI 0x00 notification events on e.g. lid-state changes.
Specifically skl_opregion_rev0p5.pdf states thid in the documentation of
the CHPD word: "Re-enumeration trigger logic in System BIOS MUST be
disabled for all the Operating Systems supporting Hot-Plug
(e.g., Windows* Longhorn and above)." Note the MUST in there.
We ignore these notifications, so this should not be a problem but many
recent DSTDs seem to all have the same copy-pasted bug in the GNOT() AML
function which is used to send these notifications. Windows likely does not
hit this bug as it presumably correcty sets CHPD to 1.
Here is an example of the broken GNOT() method:
Method (GNOT, 2, NotSerialized)
{
...
CEVT = Arg0
CSTS = 0x03
If (((CHPD == Zero) && (Arg1 == Zero)))
{
If (((OSYS > 0x07D0) || (OSYS < 0x07D6)))
{
Notify (PCI0, Arg1)
}
Else
{
Notify (GFX0, Arg1)
}
}
...
Notice that the condition for the If is always true I believe that the
|| like needs to be an &&, but there is nothing we can do about this and
in my own DSDT archive 55 of the 93 DSDTs have this issue.
When the if is true the notification gets send to the PCI root instead
of only to the GFX0 device. This causes Linux to re-enumerate PCI devices
whenever the LID opens / closes, leading to unexpected messages in dmesg:
Suspend through lid close:
[ 313.598199] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.664453] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.737982] pci_bus 0000:01: Allocating resources
[ 313.738036] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 313.738051] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[ 313.738111] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x91000000-0x911fffff 64bit pref]
[ 313.738128] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
Resume:
[ 813.623894] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[ 813.623955] pci 0000:00:03.0: reg 0x10: [mem 0x00000000-0x003fffff]
[ 813.630477] pci 0000:00:03.0: BAR 0: assigned [mem 0x91c00000-0x91ffffff]
[ 854.579101] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
And more importantly this re-enumeration races with suspend/resume causing
enumeration to not be complete when assert_isp_power_gated() from
drivers/gpu/drm/i915/display/intel_display_power.c runs. This causes
the !pci_dev_present(isp_ids) check in assert_isp_power_gated() to fail
making the condition for the WARN true, leading to:
[ 813.327886] ------------[ cut here ]------------
[ 813.327898] ISP not power gated
[ 813.328028] WARNING: CPU: 2 PID: 2317 at drivers/gpu/drm/i915/display/intel_display_power.c:4870 intel_display_print_error_state+0x2b98/0x3a80 [i915]
...
[ 813.328599] ---[ end trace f01e81b599596774 ]---
This commit fixes the unwanted ACPI notification on the PCI root device
by setting CHPD to 1, so that the broken if condition in the AML never
gets checked as notifications of type 0x00 are disabled altogether.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212204828.191288-1-hdegoede@redhat.com
When the driver submits multiple commands in a row it makes sense to
notify the host only after submitting the last one, so the host can
process them all at once, with a single vmexit.
Add functions to enable/disable notifications to allow that. Use the
new functions for primary plane updates.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20191212125346.8334-3-kraxel@redhat.com
Instead of only setting mode->specified on false on an early exit and
leaving e.g. mode->bpp_specified and mode->refresh_specified as is,
lets be consistent and just zero out the entire passed in struct at
the top of drm_mode_parse_command_line_for_connector()
Changes in v3:
-Drop "mode->specified = false;" line instead of the "return false;" (oops)
This crasher was reported-by: kernel test robot <lkp@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-11-hdegoede@redhat.com
fb_get_options() will return fb_mode_option if no video=<connector-name>
argument is present on the kernel commandline, so there is no need to also
do this in drm_mode_parse_command_line_for_connector() as our only caller
uses fb_get_options() to get the mode_option argument.
Changes in v2:
-Split out the changes dealing with the initialization of the mode struct
into a separate patch
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-10-hdegoede@redhat.com
Sometimes we want to override a connector's panel_orientation from the
kernel commandline. Either for testing and for special cases, e.g. a kiosk
like setup which uses a TV mounted in portrait mode.
Users can already specify a "rotate" option through a video= kernel cmdline
option. But that only supports 0/180 degrees (see drm_client_modeset TODO)
and only works for in kernel modeset clients, not for userspace kms users.
The "panel-orientation" connector property OTOH does support 90/270 degrees
as it leaves dealing with the rotation up to userspace and this does work
for userspace kms clients (at least those which support this property).
Changes in v2:
-Add missing ':' after @panel_orientation (reported by kbuild test robot)
BugLink: https://gitlab.freedesktop.org/plymouth/plymouth/merge_requests/83
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-9-hdegoede@redhat.com
Some options which can be specified on the commandline, such as
margin_right=..., margin_left=..., etc. are applied not only to the
specified mode, but to all modes. As such it would be nice if the user
can simply say e.g.
video=HDMI-1:margin_right=14,margin_left=24,margin_bottom=36,margin_top=42
This commit refactors drm_mode_parse_command_line_for_connector() to
add support for this, and as a nice side effect also cleans up the
function a bit.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-8-hdegoede@redhat.com
drm_connector_get_cmdline_mode() calls
drm_mode_parse_command_line_for_connector() with &connector->cmdline_mode
as mode argument, so anything which we store in the mode arguments gets
kept even if we return false.
Avoid storing a possibly false-postive bpp/refresh_specified setting
in connector->cmdline_mode by moving the setting of these to after
successful parsing of the bpp/refresh parts of the video= argument.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-7-hdegoede@redhat.com
Before this commit it was impossible to combine an extra mode argument
specified directly after the resolution with an option, e.g.
video=HDMI-1:720x480e,rotate=180 would not work, either the "e" to force
enable would need to be dropped or the ",rotate=180", otherwise the
mode_option would not be accepted.
This commit fixes this by setting parse_extras to true in this case, so
that drm_mode_parse_cmdline_res_mode() parses the extra arguments directly
after the resolution.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-4-hdegoede@redhat.com
Before this commit it was impossible to add an extra mode argument after
a bpp or refresh specifier, combined with an option, e.g.
video=HDMI-1:720x480-24e,rotate=180 would not work, either the "e" to
force enable would need to be dropped or the ",rotate=180", otherwise
the mode_option would not be accepted.
This commit fixes this by fixing the length calculation if extras_ptr
is set to stop the extra parsing at the start of the options (stop at the
',' options_ptr points to).
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-3-hdegoede@redhat.com
Before this commit, if the last option of a video=... option is for
example "rotate" without a "=<value>" after it then delim will point to
the terminating 0 of the string, and value which is sets to <delim + 1>
will point one position past the end of the string.
This commit fixes this by enforcing that the contents of delim equals '='
as it should be for options which take a value, this check is done in a
new drm_mode_parse_cmdline_int helper function which factors out the
common integer parsing code for all the options which take an int.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-1-hdegoede@redhat.com
While the common case is that the dsi controller uses an internal dphy,
accessed through the phy registers inside the dsi controller, there is
also the possibility to use a separate dphy from a different vendor.
One such case is the Rockchip px30 that uses a Innosilicon Mipi dphy,
so add the support for handling such a constellation, including the pll
also getting generated inside that external phy.
changes in v5:
- rebased on top of 5.5-rc1
- merged with dsi timing change to prevent ordering conflicts
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-5-heiko@sntech.de
If implementation-specific phy_ops need to be defined they probably
should be enabled before trying to talk to the panel and disabled only
after the panel was disabled.
Right now they are enabled last and disabled first, so might make it
impossible to talk to some panels - example for this being the px30
with an external Innosilicon dphy that needs the phy to be enabled
to transfer commands to the panel.
So move the calls appropriately.
changed in v5:
- rebased on top of 5.5-rc1
- merged with dsi timing change to prevent ordering conflicts
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-3-heiko@sntech.de
The timing values for dw-dsi are often dependent on the used display and
according to Philippe Cornu will most likely also depend on the used phy
technology in the soc-specific implementation.
To solve this and allow specific implementations to define them as needed
add a new get_timing callback to phy_ops and call this from the dphy_timing
function to retrieve the necessary values for the specific mode.
Right now this handles the hs2lp + lp2hs where Rockchip SoCs need handling
according to the phy speed, while STM seems to be ok with static values.
changes in v5:
- rebase on 5.5-rc1
- merge into px30 dsi series to prevent ordering conflicts
changes in v4:
- rebase to make it directly fit on top of drm-misc-next after all
changes in v3:
- check existence of phy_ops->get_timing in __dw_mipi_dsi_probe()
- emit actual error when get_timing() call fails
- add tags from Philippe and Yannick
changes in v2:
- add driver-specific handling, don't force all bridge users to use
the same timings, as suggested by Philippe
Suggested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-2-heiko@sntech.de
As we ignore first 8 bit of 32 bit pixel value we can add ARGB8888
format as alias of XRGB8888.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARC PGU doesn't support RGB888 (24 bit) format but supports
XRGB888 (32 bit) format. Fix incorrect format list in a driver.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Current implementation don't switch to RGB565 format if BGR888 was
previously used. Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We want the bonded request to have the same scheduler properties as its
master so that it is placed at the same depth in the queue. For example,
consider we have requests A, B and B', where B & B' are a bonded pair to
run in parallel on two engines.
A -> B
\- B'
B will run after A and so may be scheduled on an idle engine and wait on
A using a semaphore. B' sees B being executed and so enters the queue on
the same engine as A. As B' did not inherit the semaphore-chain from B,
it may have higher precedence than A and so preempts execution. However,
B' then sits on a semaphore waiting for B, who is waiting for A, who is
blocked by B.
Ergo B' needs to inherit the scheduler properties from B (i.e. the
semaphore chain) so that it is scheduled with the same priority as B and
will not be executed ahead of Bs dependencies.
Furthermore, to prevent the priorities changing via the expose fence on
B', we need to couple in the dependencies for PI. This requires us to
relax our sanity-checks that dependencies are strictly in order.
v2: Synchronise (B, B') execution on all platforms, regardless of using
a scheduler, any no-op syncs should be elided.
Fixes: ee1136908e ("drm/i915/execlists: Virtual engine bonding")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/464
Testcase: igt/gem_exec_balancer/bonded-chain
Testcase: igt/gem_exec_balancer/bonded-semaphore
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210151332.3902215-1-chris@chris-wilson.co.uk
(cherry picked from commit c81471f5e9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The GMA500 driver is using the legacy GPIO API to fetch
three optional display control GPIO lines from the SFI
description used by the Medfield platform.
Switch this over to use GPIO descriptors and delete the
custom platform data.
We create three new static locals in the tc35876x bridge
code but it is hardly any worse than the I2C client static
local already there: I tried first to move it to the DRM
driver state container but there are workarounds for
probe order in the code so I just stayed off it, as the
result is unpredictable.
People wanting to do a more throrugh and proper cleanup
of the GMA500 driver can work on top of this, I can't
solve much more since I don't have access to the hardware,
I can only attempt to tidy up my GPIO corner.
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206094301.76368-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just like in commit 523e0cc89b ("drm/i915/tgl: allow DVI/HDMI on port
A"), the port checks when reading the VBT can easily not match what the
platform really exposes. However here we only have some additional debug
messages that are not adding much value: in the previous debug message
we already print everything we know about the VBT.
Instead of keep fixing the possible port assignments according to the
platform, just nuke the additional messages.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206190552.8818-1-lucas.demarchi@intel.com
