Since zap firmware can be device specific, allow for a firmware-name
property in the zap node to specify which firmware to load, similarly to
the scheme used for dsp/wifi/etc.
v2: only need a single error msg when we can't load from firmware-name
specified path, and fix comment [Bjorn A.]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
The Rockship DRM GEM code uses vmap()/vunmap() so vmalloc header must be
included to avoid warnings like (on IA64, compile tested):
drivers/gpu/drm/rockchip/rockchip_drm_gem.c: In function ‘rockchip_gem_alloc_iommu’:
drivers/gpu/drm/rockchip/rockchip_drm_gem.c:134:20: error:
implicit declaration of function ‘vmap’ [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1577779956-7612-1-git-send-email-krzk@kernel.org
There seems to be some undocumented bandwidth
bottleneck/dependency which scales with CDCLK,
causing FIFO underruns when CDCLK is too low,
even when it's correct from BSpec point of view.
Currently for TGL platforms we calculate
min_cdclk initially based on pixel_rate divided
by 2, accounting for also plane requirements,
however in some cases the lowest possible CDCLK
doesn't work and causing the underruns.
We've found experimentally that raising cdclk to
at least pixel_rate (rather than pixel_rate/2)
eliminates these underruns, so let's use this as a
temporary workaround until the hardware team
can suggest a more precise remedy.
Explicitly stating here that this seems to be currently
rather a Hack, than final solution.
v2: Use clamp operation instead of min(Matt Roper)
v3: - Fixed commit message(Matt Roper)
- Now using pixel_rate instead of max_cdclk(Jani Nikula)
- Switched to max from clamp(Ville Syrjälä)
Hopefully this hybrid satisfies everyone :)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/issues/402
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200109220547.23817-1-stanislav.lisovskiy@intel.com
With gcc -O3 in combination with the structleak plug, the compiler can
inline very aggressively, leading to rather large stack usage:
drivers/gpu/drm/panel/panel-tpo-td028ttec1.c: In function 'td028ttec1_prepare':
drivers/gpu/drm/panel/panel-tpo-td028ttec1.c:233:1: error: the frame size of 2768 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
}
Marking jbt_reg_write_*() as noinline avoids the case where
multiple instances of this function get inlined into the same
stack frame and each one adds a copy of 'tx_buf'.
The compiler is clearly making some bad decisions here, but I
did not open a new bug report as this only happens in combination
with the structleak plugin.
This fixes mmtom ("init/Kconfig: enable -O3 for all arches")
Link: https://lore.kernel.org/lkml/CAK8P3a3jAnFZA3GFRtdYdg1-i-oih3pOQzkkrK-X3BGsFrMiZQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> [fix indent]
Link: https://patchwork.freedesktop.org/patch/msgid/20200108135116.3687988-1-arnd@arndb.de
With the db845c running AOSP, I see the following error on every
frame on the home screen:
[drm:dpu_plane_atomic_check:915] [dpu error]plane33 invalid src 2880x1620+0+470 line:2560
This is due to the error paths in atomic_check using
DPU_ERROR_PLANE(), and the drm_hwcomposer using atomic_check
to decide how to composite the frame (thus it expects to see
atomic_check to fail).
In order to avoid spamming the logs, this patch converts the
DPU_ERROR_PLANE() calls to DPU_DEBUG_PLANE() calls in
atomic_check.
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Not every platform needs quirk detection for panel orientation, so
split the drm_connector_init_panel_orientation_property into two
functions. One for platforms without the need for quirks, and the
other for platforms that need quirks.
Hans de Goede (changes in v2):
Rename the function from drm_connector_init_panel_orientation_property
to drm_connector_set_panel_orientation[_with_quirk] and pass in the
panel-orientation to set.
Beside the rename, also make the function set the passed in value
only once, if the value was set before (to a value other then
DRM_MODE_PANEL_ORIENTATION_UNKNOWN) make any further set calls a no-op.
This change is preparation for allowing the user to override the
panel-orientation for any connector from the kernel commandline.
When the panel-orientation is overridden this way, then we must ignore
the panel-orientation detection done by the driver.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200105155120.96466-1-hdegoede@redhat.com
[why]
Compilation error "undefined reference to `__udivdi3'" was
thrown on i386 architecture.
[how]
Use div_u64 for unsigned long division instead of a divide operator.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement generic system suspend/resume functions that can be used with
any output type. Currently this only implements disabling and enabling
of the IRQ functionality across system suspend/resume. This prevents an
interrupt from happening before the display driver has fully resumed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Without CONFIG_PM, some functions cause harmless warnings:
drivers/gpu/drm/tegra/sor.c:3984:12: error: 'tegra_sor_resume' defined but not used [-Werror=unused-function]
static int tegra_sor_resume(struct device *dev)
^~~~~~~~~~~~~~~~
drivers/gpu/drm/tegra/sor.c:3970:12: error: 'tegra_sor_suspend' defined but not used [-Werror=unused-function]
static int tegra_sor_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~
Mark these as __maybe_unused so the compiler can drop them
silently.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver heavily relies on the implementations for runtime
suspend/resume to be called at specific times. Unfortunately, there are
some cases where that doesn't work. One example is if the user disables
runtime PM for a given subdevice. Another example is that the PM core
acquires a reference to runtime PM during system sleep, effectively
preventing devices from going into low power modes. This is intentional
to avoid nasty race conditions, but it also causes system sleep to not
function properly on all Tegra systems.
Fix this by not implementing runtime PM at all. Instead, a minimal,
reference-counted suspend/resume infrastructure is added to the host1x
bus. This has the benefit that it can be used regardless of the system
power state (or any transitions we might be in), or whether or not the
user allows runtime PM.
Atomic modesetting guarantees that these functions will end up being
called at the right point in time, so the pitfalls for the more generic
runtime PM do not apply here.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x clients' parent to "host" because that more closely
describes what it is. The parent can be confused with the parent device
in terms of the device hierarchy. Subsequent patches will add a new
member that refers to the parent in that hierarchy.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently we first to try to unbind the VMA (and lazily rebind on next
use) as an optimisation during restore_ggtt_mappings. Ideally, the only
objects in the GGTT upon resume are the pinned kernel objects which
can't be unbound and need to be restored. As the unbind interferes with
the plan to mark those objects as active for error capture, forgo the
optimisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200110110402.1231745-1-chris@chris-wilson.co.uk
Fix indentation in the Makefile by replacing spaces with tabs.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
