Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Pull networking fixes from David Miller:
"A quick set of bug fixes after there initial networking merge:
1) Netlink multicast group storage allocator only was tested with
nr_groups equal to 1, make it work for other values too. From
Matti Vaittinen.
2) Check build_skb() return value in macb and hip04_eth drivers, from
Weidong Wang.
3) Don't leak x25_asy on x25_asy_open() failure.
4) More DMA map/unmap fixes in 3c59x from Neil Horman.
5) Don't clobber IP skb control block during GSO segmentation, from
Konstantin Khlebnikov.
6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.
7) Fix SKB segment utilization estimation in xen-netback, from David
Vrabel.
8) Fix lockdep splat in bridge addrlist handling, from Nikolay
Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
bgmac: Fix reversed test of build_skb() return value.
bridge: fix lockdep addr_list_lock false positive splat
net: smsc: Add support h8300
xen-netback: free queues after freeing the net device
xen-netback: delete NAPI instance when queue fails to initialize
xen-netback: use skb to determine number of required guest Rx requests
net: sctp: Move sequence start handling into sctp_transport_get_idx()
ipv6: update skb->csum when CE mark is propagated
net: phy: turn carrier off on phy attach
net: macb: clear interrupts when disabling them
sctp: support to lookup with ep+paddr in transport rhashtable
net: hns: fixes no syscon error when init mdio
dts: hisi: fixes no syscon fault when init mdio
net: preserve IP control block during GSO segmentation
fsl/fman: Delete one function call "put_device" in dtsec_config()
hip04_eth: fix missing error handle for build_skb failed
3c59x: fix another page map/single unmap imbalance
3c59x: balance page maps and unmaps
x25_asy: Free x25_asy on x25_asy_open() failure.
mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
...
When linux start up, we get the log below:
"Hi-HNS_MDIO 803c0000.mdio: no syscon hisilicon,peri-c-subctrl
mdio_bus mdio@803c0000: mdio sys ctl reg has not maped"
The source code about the subctrl is dealt syscon, but dts doesn't.
It cause such fault, so this patch adds the syscon info on dts files to
fixes it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull DeviceTree updates from Rob Herring:
- Rework and export the changeset API to make it available to users
other than DT overlays
- ARM secure devices binding
- OCTEON USB binding
- Clean-up of various SRAM binding docs
- Various other binding doc updates
* tag 'devicetree-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (21 commits)
drivers/of: Export OF changeset functions
Fix documentation for adp1653 DT
ARM: psci: Fix indentation in DT bindings
of/platform: export of_default_bus_match_table
of/unittest: Show broken behaviour in the platform bus
of: fix declaration of of_io_request_and_map
of/address: replace printk(KERN_ERR ...) with pr_err(...)
of/irq: optimize device node matching loop in of_irq_init()
dt-bindings: tda998x: Document the required 'port' node.
net/macb: bindings doc: Merge cdns-emac to macb
dt-bindings: Misc fix for the ATH79 DDR controllers
dt-bindings: Misc fix for the ATH79 MISC interrupt controllers
Documentation: dt: Add bindings for Secure-only devices
dt-bindings: ARM: add arm,cortex-a72 compatible string
ASoC: Atmel: ClassD: add GCK's parent clock in DT binding
DT: add Olimex to vendor prefixes
Documentation: fsl-quadspi: Add fsl,ls1021-qspi compatible string
Documentation/devicetree: document OCTEON USB bindings
usb: misc: usb3503: Describe better how to bind clock to the hub
dt-bindings: Consolidate SRAM bindings from all vendors
...
Pull oower management and ACPI updates from Rafael Wysocki:
"As far as the number of commits goes, ACPICA takes the lead this time,
followed by cpufreq and the device properties framework changes.
The most significant new feature is the debugfs-based interface to the
ACPICA's AML debugger added in the previous cycle and a new user space
tool for accessing it.
On the cpufreq front, the core is updated to handle governors more
efficiently, particularly on systems where a single cpufreq policy
object is shared between multiple CPUs, and there are quite a few
changes in drivers (intel_pstate, cpufreq-dt etc).
The device properties framework is updated to handle built-in (ie
included in the kernel itself) device properties better, among other
things by adding a fallback mechanism that will allow drivers to
provide default properties to be used in case the plaform firmware
doesn't provide the properties expected by them.
The Operating Performance Points (OPP) framework gets new DT bindings
and debugfs support.
A new cpufreq driver for ST platforms is added and the ACPI driver for
AMD SoCs will now support the APM X-Gene ACPI I2C device.
The rest is mostly fixes and cleanups all over.
Specifics:
- Add a debugfs-based interface for interacting with the ACPICA's AML
debugger introduced in the previous cycle and a new user space tool
for that, fix some bugs related to the AML debugger and clean up
the code in question (Lv Zheng, Dan Carpenter, Colin Ian King,
Markus Elfring).
- Update ACPICA to upstream revision 20151218 including a number of
fixes and cleanups in the ACPICA core (Bob Moore, Lv Zheng, Labbe
Corentin, Prarit Bhargava, Colin Ian King, David E Box, Rafael
Wysocki).
In particular, the previously added erroneous support for the _SUB
object is dropped, the concatenate operator will support all ACPI
objects now, the Debug Object handling is improved, the SuperName
handling of parameters being control methods is fixed, the
ObjectType operator handling is updated to follow ACPI 5.0A and the
handling of CondRefOf and RefOf is updated accordingly, module-
level code will be executed after loading each ACPI table now
(instead of being run once after all tables containing AML have
been loaded), the Operation Region handlers management is updated
to fix some reported problems and a the ACPICA code in the kernel
is more in line with the upstream now.
- Update the ACPI backlight driver to provide information on whether
or not it will generate key-presses for brightness change hotkeys
and update some platform drivers (dell-wmi, thinkpad_acpi) to use
that information to avoid sending double key-events to users pace
for these, add new ACPI backlight quirks (Hans de Goede, Aaron Lu,
Adrien Schildknecht).
- Improve the ACPI handling of interrupt GPIOs (Christophe Ricard).
- Fix the handling of the list of device IDs of device objects found
in the ACPI namespace and add a helper for checking if there is a
device object for a given device ID (Lukas Wunner).
- Change the logic in the ACPI namespace scanning code to create
struct acpi_device objects for all ACPI device objects found in the
namespace even if _STA fails for them which helps to avoid device
enumeration problems on Microsoft Surface 3 (Aaron Lu).
- Add support for the APM X-Gene ACPI I2C device to the ACPI driver
for AMD SoCs (Loc Ho).
- Fix the long-standing issue with the DMA controller on Intel SoCs
where ACPI tables have no power management support for the DMA
controller itself, but it can be powered off automatically when the
last (other) device on the SoC is powered off via ACPI and clean up
the ACPI driver for Intel SoCs (acpi-lpss) after previous attempts
to fix that problem (Andy Shevchenko).
- Assorted ACPI fixes and cleanups (Andy Lutomirski, Colin Ian King,
Javier Martinez Canillas, Ken Xue, Mathias Krause, Rafael Wysocki,
Sinan Kaya).
- Update the device properties framework for better handling of
built-in properties, add support for built-in properties to the
platform bus type, update the MFD subsystem's handling of device
properties and add support for passing default configuration data
as device properties to the intel-lpss MFD drivers, convert the
designware I2C driver to use the unified device properties API and
add a fallback mechanism for using default built-in properties if
the platform firmware fails to provide the properties as expected
by drivers (Andy Shevchenko, Mika Westerberg, Heikki Krogerus,
Andrew Morton).
- Add new Device Tree bindings to the Operating Performance Points
(OPP) framework and update the exynos4412 DT binding accordingly,
introduce debugfs support for the OPP framework (Viresh Kumar,
Bartlomiej Zolnierkiewicz).
- Migrate the mt8173 cpufreq driver to the new OPP bindings (Pi-Cheng
Chen).
- Update the cpufreq core to make the handling of governors more
efficient, especially on systems where policy objects are shared
between multiple CPUs (Viresh Kumar, Rafael Wysocki).
- Fix cpufreq governor handling on configurations with
CONFIG_HZ_PERIODIC set (Chen Yu).
- Clean up the cpufreq core code related to the boost sysfs knob
support and update the ACPI cpufreq driver accordingly (Rafael
Wysocki).
- Add a new cpufreq driver for ST platforms and corresponding Device
Tree bindings (Lee Jones).
- Update the intel_pstate driver to allow the P-state selection
algorithm used by it to depend on the CPU ID of the processor it is
running on, make it use a special P-state selection algorithm (with
an IO wait time compensation tweak) on Atom CPUs based on the
Airmont and Silvermont cores so as to reduce their energy
consumption and improve intel_pstate documentation (Philippe
Longepe, Srinivas Pandruvada).
- Update the cpufreq-dt driver to support registering cooling devices
that use the (P * V^2 * f) dynamic power draw formula where V is
the voltage, f is the frequency and P is a constant coefficient
provided by Device Tree and update the arm_big_little cpufreq
driver to use that support (Punit Agrawal).
- Assorted cpufreq driver (cpufreq-dt, qoriq, pcc-cpufreq,
blackfin-cpufreq) updates (Andrzej Hajda, Hongtao Jia, Jacob
Tanenbaum, Markus Elfring).
- cpuidle core tweaks related to polling and measured_us calculation
(Rik van Riel).
- Removal of modularity from a few cpuidle drivers (clps711x, ux500,
exynos) that cannot be built as modules in practice (Paul
Gortmaker).
- PM core update to prevent devices from being probed during system
suspend/resume which is generally problematic and may lead to
inconsistent behavior (Grygorii Strashko).
- Assorted updates of the PM core and related code (Julia Lawall,
Manuel Pégourié-Gonnard, Maruthi Bayyavarapu, Rafael Wysocki, Ulf
Hansson).
- PNP bus type updates (Christophe Le Roy, Heiner Kallweit).
- PCI PM code cleanups (Jarkko Nikula, Julia Lawall).
- cpupower tool updates (Jacob Tanenbaum, Thomas Renninger)"
* tag 'pm+acpi-4.5-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (177 commits)
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
PM / OPP: Use snprintf() instead of sprintf()
Documentation: cpufreq: intel_pstate: enhance documentation
ACPI, PCI, irq: remove redundant check for null string pointer
ACPI / video: driver must be registered before checking for keypresses
cpufreq-dt: fix handling regulator_get_voltage() result
cpufreq: governor: Fix negative idle_time when configured with CONFIG_HZ_PERIODIC
PM / sleep: Add support for read-only sysfs attributes
ACPI: Fix white space in a structure definition
ACPI / SBS: fix inconsistent indenting inside if statement
PNP: respect PNP_DRIVER_RES_DO_NOT_CHANGE when detaching
ACPI / PNP: constify device IDs
ACPI / PCI: Simplify acpi_penalize_isa_irq()
...
Pull ARM updates from Russell King:
- UEFI boot and runtime services support for ARM from Ard Biesheuvel
and Roy Franz.
- DT compatibility with old atags booting protocol for Nokia N900
devices from Ivaylo Dimitrov.
- PSCI firmware interface using new arm-smc calling convention from
Jens Wiklander.
- Runtime patching for udiv/sdiv instructions for ARMv7 CPUs that
support these instructions from Nicolas Pitre.
- L2x0 cache updates from Dirk B and Linus Walleij.
- Randconfig fixes from Arnd Bergmann.
- ARMv7M (nommu) updates from Ezequiel Garcia
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (34 commits)
ARM: 8481/2: drivers: psci: replace psci firmware calls
ARM: 8480/2: arm64: add implementation for arm-smccc
ARM: 8479/2: add implementation for arm-smccc
ARM: 8478/2: arm/arm64: add arm-smccc
ARM: 8494/1: mm: Enable PXN when running non-LPAE kernel on LPAE processor
ARM: 8496/1: OMAP: RX51: save ATAGS data in the early boot stage
ARM: 8495/1: ATAGS: move save_atags() to arch/arm/include/asm/setup.h
ARM: 8452/3: PJ4: make coprocessor access sequences buildable in Thumb2 mode
ARM: 8482/1: l2x0: make it possible to disable outer sync from DT
ARM: 8488/1: Make IPI_CPU_BACKTRACE a "non-secure" SGI
ARM: 8487/1: Remove IPI_CALL_FUNC_SINGLE
ARM: 8485/1: cpuidle: remove cpu parameter from the cpuidle_ops suspend hook
ARM: 8484/1: Documentation: l2c2x0: Mention separate controllers explicitly
ARM: 8483/1: Documentation: l2c: Rename l2cc to l2c2x0
ARM: 8477/1: runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()
ARM: 8476/1: VDSO: use PTR_ERR_OR_ZERO for vma check
ARM: 8453/2: proc-v7.S: don't locate temporary stack space in .text section
ARM: add UEFI stub support
ARM: wire up UEFI init and runtime support
ARM: only consider memblocks with NOMAP cleared for linear mapping
...
Merge "BCM2835 SOC changes for 4.5" from Eric Anholt:
This pull request includes the bcm2835 changes for 4.5 targeting the
arm-soc next/soc branch.
* tag 'bcm2835-soc-next-2015-12-28' of http://github.com/anholt/linux:
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
Conflicts:
arch/arm/mach-bcm/Kconfig
The i.MX device tree updates for 4.5:
- New boards support: imx51-ts4800, imx6q-novena, CompuLab imx7d SoM/SBC,
vf610m4-cosmic
- Add ADC device support for imx6ul and imx7d
- Remove config space from PCIe controller ranges property for i.MX6
- Add Vivante GPU nodes for i.MX6
- Add DCU, LCD, and SATA devices for LS1021A
- A series to update Ventana gw5xxx boards getting HDMI and LVDS to work
simultaneously and devices like PWM and SPI added
- Quite a few random cleanups and minor updates
* tag 'imx-dt-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx7d: sbc-imx7: add basic board support
ARM: dts: imx7d: cl-som-imx7: add basic module support
ARM: dts: TS-4800: add touchscreen support
ARM: dts: ts-4800: Add LCD support
ARM: dts: imx6q: add Novena board
devicetree: bindings: Add vendor prefix for Kosagi
ARM: dts: TS-4800: use weim IP to map the FPGA
ARM: dts: TS-4800: drop uart rts/cts pin reservations
ARM: dts: imx6: add Vivante GPU nodes
ARM: dts: imx28: add alternate auart4 pinmux
ARM: dts: ls1021a: add sata node to dts
ARM: dts: TS-4800: add basic device tree
of: documentation: add bindings documentation for TS-4800
of: add vendor prefix for Technologic Systems
ARM: dts: imx7d-sdb: add ADC support
ARM: dts: imx7d.dtsi: add ADC support
ARM: dts: vf-colibri: add CAN support
ARM: mxs: dt: cfa10057: fix backlight PWM
ARM: dts: imx6qdl: move GIC to right location in DT
ARM: dts: imx6qdl: add IPU aliases
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Second set of omap device tree changes for v4.5 merge window. This series
updates the EDMA bindings based on the various fixes to split EDMA into
separate independent devices. It also adds support for more devices on the
CompuLab cm-t335 and LogicPD Torpedo boards, and enables the new bindings
for qspi for am437x and dra7. There are also few dra7 regulator fixes, and
change of gpoi-key,wakeup to wakeup-source.
These depend on commit ae0add740c ("dmaengine: edma: DT: Change reserved
slot array from 16bit to 32bit type") already merged into mainline.
* tag 'omap-for-v4.5/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: LogicPD Torpedo: Add Touchscreen Support
ARM: dts: DRA7-EVM: Add regulator-allow-bypass property for ldo9
ARM: dts: DRA72-EVM: Add regulator-allow-bypass property for ldo1 and ldo2
ARM: dts: AM4372: add entry for qspi mmap region
ARM: dts: DRA7: add entry for qspi mmap region
ARM: OMAP2+: LogicPD Torpedo: Revert Duplicative Entries
ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth
ARM: OMAP2+: LogicPD Torpedo: Add LCD Type 15 Support
ARM: dts: cm-t335: add support for bluetooth
ARM: dts: cm-t335: add support for DVI/LCD
ARM: dts: cm-t335: add support for I2C GPIO expander
ARM: dts: cm-t335: add support for SBC-T335
ARM: dts: cm-t335: add support for USB0
ARM: dts: omap: replace legacy *,wakeup property with wakeup-source
ARM: dts: am335x: replace gpio-key,wakeup with wakeup-source property
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: DT: Change reserved slot array from 16bit to 32bit type
dmaengine: edma: DT: Change memcpy channel array from 16bit to 32bit type
Signed-off-by: Olof Johansson <olof@lixom.net>
Another new soc - the rk3228 quad-core cortex-a7, a new rk3036 board,
support for the efuses on Rockchip socs and some improvements for
rk3288 regulators.
* tag 'v4.5-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the kylin board for rk3036
ARM: dts: rockchip: add the sdio/sdmmc node for rk3036
ARM: dts: rockchip: fix the pinctrl bias settings for rk3036
ARM: dts: rockchip: add eFuse node for rk3188 SoCs
ARM: dts: rockchip: add eFuse node for rk3066a SoCs
ARM: dts: rockchip: add eFuse config of rk3288 SoC
ARM: dts: rockchip: add rk3228-evb board
ARM: dts: rockchip: add core rk3228 dtsi
clk: rockchip: Add the clock ids of rk3288 eFuses
ARM: dts: rockchip: Fix typo in rk3288 sdmmc card detect pin name
ARM: dts: rockchip: fix voltage ranges for rk3288-evb-act8846 board
ARM: dts: rockchip: move the public part to rk3288-evb common
ARM: dts: rockchip: add 2 regulators for rk3288-evb-act8846
ARM: dts: rockchip: correct the name of REG8 for rk3288-evb-act8846
clk: rockchip: add dt-binding header for rk3228
clk: rockchip: add id for mipidsi sclk on rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
Add regulators to the scpsys binding.
Move the include of the reset contoller to include/dt-bindings/reset.
Add basic support for mt2701 SoC and evaluation board.
* tag 'v4.4-next-dts' of https://github.com/mbgg/linux-mediatek:
dt-bindings: soc: Add supplies for Mediatek SCPSYS unit
ARM: mediatek: DT: Move reset controller constants into common location
ARM: dts: mediatek: add MT2701 basic support
Document: DT: Add bindings for mediatek MT2701 SoC Platform
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 4.5 (part 3)
Add dts for the following boards:
- Zyxel NSA325
- PogoPlug series 4
Add GPU support for Dove
Update boolean property to wakeup source for isil
* tag 'mvebu-dt-4.5-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada: replace isil, irq2-can-wakeup-machine with wakeup-source property
ARM: dts: enable GPU for SolidRun's Cubox
ARM: dts: dove: add DT GPU support
ARM: mvebu: kirkwood: add PogoPlug series 4 device tree
ARM: mvebu: add kirkwood compatibles for cloudengine boards
ARM: dts: kirkwood: Add DTS for Zyxel NSA325
Signed-off-by: Olof Johansson <olof@lixom.net>
Third Round of Renesas ARM64 Based SoC DT Updates for v4.5
* Enable SATA
* Add salvator-x part number to DT bindings documentation
* Enable all four A57 cores instead of just one
* Enhanced audio support:
- Use CS2000 as AUDIO_CLK_B
- Set ak4613 In/Out pin as single-end
* tag 'renesas-arm64-dt3-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
arm64: dts: r8a7795: Add Cortex-A57 CPU cores
arm64: dts: r8a7795: Add PSCI node
arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B
arm64: renesas: salvator-x: set ak4613 In/Out pin as single-end
Signed-off-by: Olof Johansson <olof@lixom.net>
Cortex-A72 has a PMUv3 implementation that is compatible with the PMU
implemented by Cortex-A57.
This patch hooks up the new compatible string so that the Cortex-A57
event mappings are used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
According to commit 2503a5ecd8
"ARM: 6201/1: RealView: Do not use outer_sync() on ARM11MPCore
boards with L220" Some PB11MPCore RealView core tiles have broken
outer_sync.
We got rid of the custom barriers from the machine by disabling
outer sync, but that was just for the boardfile case. We have
to be able to do the same in the device tree case.
Since __l2c_init() is cloning and copying the L2C vtable,
we pass an argument to this function to optionally numb
the outer sync operation if desired, before initializing
the cache.
After this we can set up the cache correctly on the RealView
PB11MPCore. This was tested on a PB11MPCore known to have the
issue. Before this, spurious crashes would occur if we try to
set up the cache properly, after this it boots rock solid.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation in l2c2x0.txt is only valid for L2C210/L2C220/L2C310
(also known as PL210/PL220/PL310 and variants). Mention this explicitly.
And add a note why this isn't valid for integrated L2 controllers.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation in the l2cc.txt is specific to the L2 cache
controllers L2C210/L2C220/L2C310 (also known as PL210/PL220/PL310
and variants) and not generic as the file name implies. It's not
valid for integrated L2 controllers as found in e.g.
Cortex-A15/A7/A57/A53.
Reflect this by adapting the file name accordingly.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "Realview multiplatform support" from Linus Walleij:
The board and infrastructure changes for RealView
multiplatform and extended DT support.
* tag 'realview-base-armsoc-1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add an DT SMP boot method
ARM: realview: select SP810 and ICST for the DT variant
soc: versatile: add support for the PB11MPCore
clk: versatile-icst: add device tree support
clk: versatile-icst: refactor to allocate regmap separately
clk: versatile-icst: convert to use regmap
ARM: realview: remove private barrier implementation
ARM: no longer force unbuffered DMA for realview
clk/realview: stop using machine headers
ARM: realview: don't map undefined PCI registers
ARM: realview: remove sparsemem hack
Conflicts:
drivers/clk/versatile/Kconfig
Merge "Realview DT files" from Linus Walleij:
The device tree changes for the continued RealView DT
support.
* tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add device tree for PB11MPCore
clk: add ARM syscon ICST device tree bindings
ARM: add DT bindings for the ARM11MPCore CPU cluster
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
The ARM11MPCore has a Snoop Control Unit, but references to it
were missing from the DT specification. Define a compatible
string for this unit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds an SMP boot method for the ARM RealView reference
designs. We also select HAVE_SMP by default and make it use
SMP_ON_UP so we only need to support one single kernel across
the RealView reference designs when using DT.
The RealViews need to have the SCU (Snoop Control Unit)
activated on boot, and this is now done by looking up its
address from the device tree and initializing it and counting
the available cores.
The RealViews boot by using a magic address register in the
system controller (SYS_FLAGS) to store the boot address,
the ROM will then read this register to the PC when the CPUs
are taken out of WFI. This code uses a handle to the syscon
regmap to access this register.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge "rockchip dts64 changes for 4.5" from Heiko Stuebner:
First round of 64bit devicetree changes for Rockchip socs.
This includes support for the evaluation board of the rk3368
as well as the dts-part for the newly added thermal management
support, rk3368 pwm nodes and an alias.
* tag 'v4.5-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add rk3368 evaluation board
arm64: dts: rockchip: add the pwm node info for RK3368 SoCs
arm64: dts: rockchip: Enable the Thermal on R88 board
arm64: dts: rockchip: Add main thermal info to rk3368.dtsi
arm64: dts: rockchip: Add the thermal data found on RK3368
arm64: dts: rockchip: Setup rk3368 ethernet0 alias for u-boot
Merge "Device tree changes for omaps for v4.5 merge window" from Tony Lindgren:
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
* tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (97 commits)
ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi
ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
ARM: dts: am57xx: sbc-am57x: add HDMI support
ARM: dts: am57xx: compulab-sb-som: add HDMI connector
ARM: dts: am57xx: sbc-am57x: add LCD support
ARM: dts: am57xx: sbc-am57x: add GPIO expander support
ARM: dts: am57xx: sbc-am57x: add EEPROM support
ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux
ARM: dts: am57xx: cl-som-am57x: add MMC1 support
ARM: dts: am57xx: sbc-am57x: add basic board support
ARM: dts: am57xx: cl-som-am57x: add analog audio support
ARM: dts: am57xx: cl-som-am57x: add touchscreen support
ARM: dts: am57xx: cl-som-am57x: add USB support
ARM: dts: am57xx: cl-som-am57x: add dual EMAC support
ARM: dts: am57xx: cl-som-am57x: add spi-flash support
ARM: dts: am57xx: cl-som-am57x: add eMMC support
ARM: dts: am57xx: cl-som-am57x: add EEPROM support
ARM: dts: am57xx: cl-som-am57x: add I2C3 support
ARM: dts: am57xx: cl-som-am57x: dts: add RTC support
...
The dynamic power consumption of a device is proportional to the
square of voltage (V) and the clock frequency (f). It can be expressed as
Pdyn = dynamic-power-coefficient * V^2 * f.
The coefficient represents the running time dynamic power consumption in
units of mw/MHz/uVolt^2 and can be used in the above formula to
calculate the dynamic power in mW.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The existing device tree bindings assume that we are only trying to
describe a single address space with a device tree (for ARM, either
the Normal or the Secure world). Some uses for device tree need to
describe both Normal and Secure worlds in a single device tree. Add
documentation of how to do this, by adding extra properties which
describe when a device appears differently in the two worlds or when
it only appears in one of them.
The binding describes the general principles for adding new
properties describing the secure world, but for now we only need a
single new property, "secure-status", which can be used to annotate
devices to indicate that they are only visible in one of the two
worlds.
The primary expected use of this binding is for a virtual machine
like QEMU to describe the VM layout to a TrustZone aware firmware
(which would then use the secure-only devices itself, and pass the DT
on to a kernel running in the non-secure world, which ignores the
secure-only devices and uses the rest).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a compatible string "brcm,bcm-nsp-smp" for Broadcom's
Northstar Plus CPU to the 32-bit ARM CPU device tree binding
documentation file and create a new binding documentation for
Northstar Plus CPU.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
