The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.
Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of the RXQ/TXQ size granularity design-params had two
problems: it had a 64-bit divide that didn't build on 32-bit platforms,
and it could divide by zero if the NIC supplied 0 as the value of the
design-param. Fix both by checking for 0 and for a granularity bigger
than our min-size; if the granularity <= EFX_MIN_DMAQ_SIZE then it fits
in 32 bits, so we can cast it to u32 for the divide.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c3e302edca ("net: phy: marvell10g: fix temperature sensor on 2110")
added a check for PHY ID via phydev->drv->phy_id in a function which is
called by devres at a time when phydev->drv is already set to null by
phy_remove function.
This null pointer dereference can be triggered via SFP subsystem with a
SFP module containing this Marvell PHY. When the SFP interface is put
down, the SFP subsystem removes the PHY.
Fixes: c3e302edca ("net: phy: marvell10g: fix temperature sensor on 2110")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the missing clk_disable_unprepare() before return
from emac_clks_phase1_init() in the error handling case.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "devm_kcalloc".
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the compile warnings of 'strncpy' output truncated before
terminating nul copying N bytes from a string of the same length
Signed-off-by: Luo bin <luobin9@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Added needed_headroom
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes.
So the value of needed_headroom in this driver should be 3 - 1.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, while
calculating tcp hdr length, it does not take into account if the
packet is encapsulated or not.
This patch fixes this issue by using correct reference for inner
tcp header.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit introduced a late error path in phy_device_create()
which fails to release the device name allocated by dev_set_name().
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the USB device's device tree node when looking for a MAC address.
The struct device embedded into the struct net_device does not have a
device tree node attached at all.
The reason why this went unnoticed is because the system where this was
tested was one of the few development units that had its OTP programmed,
as opposed to production systems where the MAC address is stored in a
separate EEPROM and is passed via device tree by the firmware.
Reported-by: EJ Hsu <ejh@nvidia.com>
Fixes: acb6d3771a ("r8152: Use MAC address from device tree if available")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added a skb->len check
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Changed to use needed_headroom instead of hard_header_len to request
necessary headroom to be allocated
In net/packet/af_packet.c, the function packet_snd first reserves a
headroom of length (dev->hard_header_len + dev->needed_headroom).
Then if the socket is a SOCK_DGRAM socket, it calls dev_hard_header,
which calls dev->header_ops->create, to create the link layer header.
If the socket is a SOCK_RAW socket, it "un-reserves" a headroom of
length (dev->hard_header_len), and assumes the user to provide the
appropriate link layer header.
So according to the logic of af_packet.c, dev->hard_header_len should
be the length of the header that would be created by
dev->header_ops->create.
However, this driver doesn't provide dev->header_ops, so logically
dev->hard_header_len should be 0.
So we should use dev->needed_headroom instead of dev->hard_header_len
to request necessary headroom to be allocated.
This change fixes kernel panic when this driver is used with AF_PACKET
SOCK_RAW sockets.
Call stack when panic:
[ 168.399197] skbuff: skb_under_panic: text:ffffffff819d95fb len:20
put:14 head:ffff8882704c0a00 data:ffff8882704c09fd tail:0x11 end:0xc0
dev:veth0
...
[ 168.399255] Call Trace:
[ 168.399259] skb_push.cold+0x14/0x24
[ 168.399262] eth_header+0x2b/0xc0
[ 168.399267] lapbeth_data_transmit+0x9a/0xb0 [lapbether]
[ 168.399275] lapb_data_transmit+0x22/0x2c [lapb]
[ 168.399277] lapb_transmit_buffer+0x71/0xb0 [lapb]
[ 168.399279] lapb_kick+0xe3/0x1c0 [lapb]
[ 168.399281] lapb_data_request+0x76/0xc0 [lapb]
[ 168.399283] lapbeth_xmit+0x56/0x90 [lapbether]
[ 168.399286] dev_hard_start_xmit+0x91/0x1f0
[ 168.399289] ? irq_init_percpu_irqstack+0xc0/0x100
[ 168.399291] __dev_queue_xmit+0x721/0x8e0
[ 168.399295] ? packet_parse_headers.isra.0+0xd2/0x110
[ 168.399297] dev_queue_xmit+0x10/0x20
[ 168.399298] packet_sendmsg+0xbf0/0x19b0
......
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
This check an inherent race. It opens a race where
an error code has already been set or cleared yet
the URB has not been given back. We cannot do
such an optimization and must unlink unconditionally.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this fails, kmalloc() will print a report including
a stack trace. There is no need for a separate complaint.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver tries to reuse code for disconnect in case
of a failed probe.
If resources need to be freed after an error in probe, the
netdev must not be freed because it has never been registered.
Fix it by telling the helper which path we are in.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add a new host cap bit and a corresponding DT property, to support
power cycling of the card by FW at system suspend/resume.
- Fix clock rate setting for SDIO in SDR12/SDR25 speed-mode
- Fix switch to 1/4-bit mode at system suspend/resume for SD-combo
cards
- Convert the mmc-pwrseq DT bindings to the json-schema
- Always allow the card detect uevent to be consumed by userspace
MMC host controllers:
- Convert a few DT bindings to the json-schema
- mtk-sd:
- Add support for command queue through cqhci
- Add support for the MT6779 variant
- renesas_sdhi_internal_dmac:
- Fix dma unmapping in the error path
- sdhci_am654:
- Add support for the AM65x PG2.0 variant
- Extend support for phys/clocks
- sdhci-cadence:
- Drop incorrect HW tuning for SD mode
- sdhci-msm:
- Add support for interconnect bandwidth scaling
- Enable internal voltage control
- Enable low power state for pinctrls
- sdhci-of-at91:
- Ludovic Desroches handovers maintenance to Eugen Hristev
- sdhci-pci-gli:
- Improve clock handling for GL975x
- sdhci-pci-o2micro:
- Add HW tuning for SDR104 mode
- Fix support for O2 host controller Seabird1"
* tag 'mmc-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (66 commits)
mmc: mediatek: make function msdc_cqe_disable() static
MAINTAINERS: mmc: sdhci-of-at91: handover maintenance to Eugen Hristev
dt-bindings: mmc: mediatek: Add document for mt6779
mmc: mediatek: command queue support
mmc: mediatek: refine msdc timeout api
mmc: mediatek: add MT6779 MMC driver support
mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
mmc: sdhci-pci-o2micro: Bug fix for O2 host controller Seabird1
mmc: via-sdmmc: use generic power management
memstick: jmb38x_ms: use generic power management
mmc: sdhci-cadence: do not use hardware tuning for SD mode
mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL975x
mmc: cqhci: Fix a print format for the task descriptor
mmc: sdhci-of-arasan: fix timings allocation code
mmc: sdhci: Fix a potential uninitialized variable
dt-bindings: mmc: renesas,sdhi: convert to YAML
dt-bindings: mmc: convert arasan sdhci bindings to yaml
mmc: sdhci: Fix potential null pointer access while accessing vqmmc
mmc: core: Add MMC_CAP2_FULL_PWR_CYCLE_IN_SUSPEND
dt-bindings: mmc: Add full-pwr-cycle-in-suspend property
...
Although we can detect the chip revision 100% at runtime, it is useful
to specify it in the device tree compatible string too, because
otherwise there would be no way to assess the correctness of device tree
bindings statically, without booting a board (only some switch versions
have internal RGMII delays and/or an SGMII port).
But for testing the P/Q/R/S support, what I have is a reworked board
with the SJA1105T replaced by a pin-compatible SJA1105Q, and I don't
want to keep a separate device tree blob just for this one-off board.
Since just the chip has been replaced, its RGMII delay setup is
inherently the same (meaning: delays added by the PHY on the slave
ports, and by PCB traces on the fixed-link CPU port).
For this board, I'd rather have the driver shout at me, but go ahead and
use what it found even if it doesn't match what it's been told is there.
[ 2.970826] sja1105 spi0.1: Device tree specifies chip SJA1105T but found SJA1105Q, please fix it!
[ 2.980010] sja1105 spi0.1: Probed switch chip: SJA1105Q
[ 3.005082] sja1105 spi0.1: Enabled switch tagging
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull USB/Thunderbolt updates from Greg KH:
"Here is the large set of USB and Thunderbolt patches for 5.9-rc1.
Nothing really magic/major in here, just lots of little changes and
updates:
- clean up language usages in USB core and some drivers
- Thunderbolt driver updates and additions
- USB Gadget driver updates
- dwc3 driver updates (like always...)
- build with "W=1" warning fixups
- mtu3 driver updates
- usb-serial driver updates and device ids
- typec additions and updates for new hardware
- xhci debug code updates for future platforms
- cdns3 driver updates
- lots of other minor driver updates and fixes and cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (330 commits)
usb: common: usb-conn-gpio: Register charger
usb: mtu3: simplify mtu3_req_complete()
usb: mtu3: clear dual mode of u3port when disable device
usb: mtu3: use MTU3_EP_WEDGE flag
usb: mtu3: remove useless member @busy in mtu3_ep struct
usb: mtu3: remove repeated error log
usb: mtu3: add ->udc_set_speed()
usb: mtu3: introduce a funtion to check maximum speed
usb: mtu3: clear interrupts status when disable interrupts
usb: mtu3: reinitialize CSR registers
usb: mtu3: fix macro for maximum number of packets
usb: mtu3: remove unnecessary pointer checks
usb: xhci: Fix ASMedia ASM1142 DMA addressing
usb: xhci: define IDs for various ASMedia host controllers
usb: musb: convert to devm_platform_ioremap_resource_byname
usb: gadget: tegra-xudc: convert to devm_platform_ioremap_resource_byname
usb: gadget: r8a66597: convert to devm_platform_ioremap_resource_byname
usb: dwc3: convert to devm_platform_ioremap_resource_byname
usb: cdns3: convert to devm_platform_ioremap_resource_byname
usb: phy: am335x: convert to devm_platform_ioremap_resource_byname
...
This reverts commit 71130f2997.
In commit 71130f2997 ("vxlan: fix tos value before xmit") we want to
make sure the tos value are filtered by RT_TOS() based on RFC1349.
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| PRECEDENCE | TOS | MBZ |
+-----+-----+-----+-----+-----+-----+-----+-----+
But RFC1349 has been obsoleted by RFC2474. The new DSCP field defined like
0 1 2 3 4 5 6 7
+-----+-----+-----+-----+-----+-----+-----+-----+
| DS FIELD, DSCP | ECN FIELD |
+-----+-----+-----+-----+-----+-----+-----+-----+
So with
IPTOS_TOS_MASK 0x1E
RT_TOS(tos) ((tos)&IPTOS_TOS_MASK)
the first 3 bits DSCP info will get lost.
To take all the DSCP info in xmit, we should revert the patch and just push
all tos bits to ip_tunnel_ecn_encap(), which will handling ECN field later.
Fixes: 71130f2997 ("vxlan: fix tos value before xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the accelerated networking SRIOV VF device has lost carrier
use the synthetic network device which is available as backup
path. This is a rare case since if VF link goes down, normally
the VMBus device will also loose external connectivity as well.
But if the communication is between two VM's on the same host
the VMBus device will still work.
Reported-by: "Shah, Ashish N" <ashish.n.shah@intel.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch warning:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.c:2419
alloc_channel() warn: passing zero to 'ERR_PTR'
setup_dpcon() should return ERR_PTR(err) instead of zero in error
handling case.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just recently noticed that ethernet does not work anymore since v5.5
on the GARDENA smart Gateway, which is based on the AT91SAM9G25.
Debugging showed that the "GEM bits" in the NCFGR register are now
unconditionally accessed, which is incorrect for the !macb_is_gem()
case.
This patch adds the macb_is_gem() checks back to the code
(in macb_mac_config() & macb_mac_link_up()), so that the GEM register
bits are not accessed in this case any more.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
A dead lock was triggered on thunderx driver:
CPU0 CPU1
---- ----
[01] lock(&(&nic->rx_mode_wq_lock)->rlock);
[11] lock(&(&mc->mca_lock)->rlock);
[12] lock(&(&nic->rx_mode_wq_lock)->rlock);
[02] <Interrupt> lock(&(&mc->mca_lock)->rlock);
The path for each is:
[01] worker_thread() -> process_one_work() -> nicvf_set_rx_mode_task()
[02] mld_ifc_timer_expire()
[11] ipv6_add_dev() -> ipv6_dev_mc_inc() -> igmp6_group_added() ->
[12] dev_mc_add() -> __dev_set_rx_mode() -> nicvf_set_rx_mode()
To fix it, it needs to disable bh on [1], so that the timer on [2]
wouldn't be triggered until rx_mode_wq_lock is released. So change
to use spin_lock_bh() instead of spin_lock().
Thanks to Paolo for helping with this.
v1->v2:
- post to netdev.
Reported-by: Rafael P. <rparrazo@redhat.com>
Tested-by: Dean Nelson <dnelson@redhat.com>
Fixes: 469998c861 ("net: thunderx: prevent concurrent data re-writing by nicvf_set_rx_mode")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.
If metadata collection is enabled, set destination and source
addresses for the flow as if we were receiving the packet, so that
Open vSwitch can match the ICMP error against the existing
association.
v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is a bridge or Open vSwitch port, and we can't
forward a packet because it exceeds the local PMTU estimate,
trigger an ICMP or ICMPv6 reply to the sender, using the same
interface to forward it back.
If metadata collection is enabled, reverse destination and source
addresses, so that Open vSwitch is able to match this packet against
the existing, reverse flow.
v2: Use netif_is_any_bridge_port() (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's currently possible to bridge Ethernet tunnels carrying IP
packets directly to external interfaces without assigning them
addresses and routes on the bridged network itself: this is the case
for UDP tunnels bridged with a standard bridge or by Open vSwitch.
PMTU discovery is currently broken with those configurations, because
the encapsulation effectively decreases the MTU of the link, and
while we are able to account for this using PMTU discovery on the
lower layer, we don't have a way to relay ICMP or ICMPv6 messages
needed by the sender, because we don't have valid routes to it.
On the other hand, as a tunnel endpoint, we can't fragment packets
as a general approach: this is for instance clearly forbidden for
VXLAN by RFC 7348, section 4.3:
VTEPs MUST NOT fragment VXLAN packets. Intermediate routers may
fragment encapsulated VXLAN packets due to the larger frame size.
The destination VTEP MAY silently discard such VXLAN fragments.
The same paragraph recommends that the MTU over the physical network
accomodates for encapsulations, but this isn't a practical option for
complex topologies, especially for typical Open vSwitch use cases.
Further, it states that:
Other techniques like Path MTU discovery (see [RFC1191] and
[RFC1981]) MAY be used to address this requirement as well.
Now, PMTU discovery already works for routed interfaces, we get
route exceptions created by the encapsulation device as they receive
ICMP Fragmentation Needed and ICMPv6 Packet Too Big messages, and
we already rebuild those messages with the appropriate MTU and route
them back to the sender.
Add the missing bits for bridged cases:
- checks in skb_tunnel_check_pmtu() to understand if it's appropriate
to trigger a reply according to RFC 1122 section 3.2.2 for ICMP and
RFC 4443 section 2.4 for ICMPv6. This function is already called by
UDP tunnels
- a new function generating those ICMP or ICMPv6 replies. We can't
reuse icmp_send() and icmp6_send() as we don't see the sender as a
valid destination. This doesn't need to be generic, as we don't
cover any other type of ICMP errors given that we only provide an
encapsulation function to the sender
While at it, make the MTU check in skb_tunnel_check_pmtu() accurate:
we might receive GSO buffers here, and the passed headroom already
includes the inner MAC length, so we don't have to account for it
a second time (that would imply three MAC headers on the wire, but
there are just two).
This issue became visible while bridging IPv6 packets with 4500 bytes
of payload over GENEVE using IPv4 with a PMTU of 4000. Given the 50
bytes of encapsulation headroom, we would advertise MTU as 3950, and
we would reject fragmented IPv6 datagrams of 3958 bytes size on the
wire. We're exclusively dealing with network MTU here, though, so we
could get Ethernet frames up to 3964 octets in that case.
v2:
- moved skb_tunnel_check_pmtu() to ip_tunnel_core.c (David Ahern)
- split IPv4/IPv6 functions (David Ahern)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for v5.9
Second set of patches for v5.9. mt76 has most of patches this time.
Otherwise it's just smaller fixes and cleanups to other drivers.
There was a major conflict in mt76 driver between wireless-drivers and
wireless-drivers-next. I solved that by merging the former to the
latter.
Major changes:
rtw88
* add support for ieee80211_ops::change_interface
* add support for enabling and disabling beacon
* add debugfs file for testing h2c
mt76
* ARP filter offload for 7663
* runtime power management for 7663
* testmode support for mfg calibration
* support for more channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_<level> in place of VELOCITY_PRT.
Use pr_<level> in place of printk(KERN_<LEVEL>.
Miscellanea:
o Add pr_fmt to prefix pr_<level> output with "via-velocity: "
o Remove now unused functions and macros
o Realign some logging lines
o Remove devname where pr_<level> is also used
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF should check whether the cmd from VF is supported and its content
is right before passing it to hw.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add support to generate mailbox random id of VF to ensure that
mailbox messages PF received are from the correct VF.
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mt76 driver had major conflicts within mt7615 directory. To make it easier for
every merge wireless-drivers to wireless-drivers-next and solve those
conflicts.
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2020-08-03
This patchset introduces some updates to mlx5 driver.
1) Jakub converts mlx5 to use the new udp tunnel infrastructure.
Starting with a hack to allow drivers to request a static configuration
of the default vxlan port, and then a patch that converts mlx5.
2) Parav implements change_carrier ndo for VF eswitch representors,
to speedup link state control of representors netdevices.
3) Alex Vesker, makes a simple update to software steering to fix an issue
with push vlan action sequence
4) Leon removes a redundant dump stack on error flow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't yet have a .sriov_configure() to create them, though.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-tests for event and interrupt reception and NVRAM.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC stats work much the same as on EF10, with a periodic DMA to a region
specified via an MCDI.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring down the TX and RX queues at ifdown, so that we can then fini the
EVQs (otherwise the MC would return EBUSY because they're still in use).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes checksum offload and TSO, so declare those in our netdev features.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several parts of the EF100 architecture are parameterised (to allow
varying capabilities on FPGAs according to resource constraints), and
these parameters are exposed to the driver through a TLV-encoded
region of the BAR.
For the most part we either don't care about these values at all or
just need to sanity-check them against the driver's assumptions, but
there are a number of TSO limits which we record so that we will be
able to check against them in the TX path when handling GSO skbs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
