also refactor debug option. now pipe_split_policy are
dynamic = no hack around dcn_calcs. will split based on HW recommendation
avoid = avoid split if we can support the config with higher voltage
avoid_multi_display = allow split with single display output.
force_single_disp_pipe_split
force single display to pipe split to improve stutter efficiency
by using DET buffers using 2 HUBP.
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In SST daisy chain scenario, edid is getting read in mst hotplug
routine. It is getting conflict with drm send_enum_path_resources
kernel thread in terms of i2c bus which is getting locked up in
such case.
Have edid being read in get_mode hook, instead of in hotplug
routine.
Signed-off-by: Jerry Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of two monitor connected and turn off one of the monitors,
OTG0 is locked after graphic plane off due to redundant programming
front end regs.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
link type is not updated before mst topology discovery.
This causes issue when branch device response to link address after before
the start topology discovery event finishes.
[Solution]
update link type to mst before topology discovery
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous changed removed the hack to match mpcc_idd
with mi instance. This causes pstate hang on resume
from hibernate for yet unknown reason. Add the hack
back for now to work around the issue. More debugging
required in init_hw to root cause the hang.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
hbr2 compliance eye output is unstable
(toggling on and off) with debugger break.
This caueses intermittent PHY automation failure.
Need to look into the root cause later
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prevent NULL pointer on new_stream being added to ctx
when added MST connectors cannot be found in existing crtc_state
in the chained mode
Signed-off-by: Jerry Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needs effort to take care of the fake sink scenario
in downstream daisy chain device. Exclude MST from
fake sink feature for now.
Signed-off-by: Jerry Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During system suspend, we:
1. Cache a duplicate of the current DRM atomic state, which calls hooks
to duplicate our internal states.
2. Call hooks to disable all functionalities.
3. System suspended.
During resume, we attempt to restore the cached state. However, our
interal states are now stale, since step 1 was done before step 2.
i.e. our cached state does not reflect the disabled nature of things.
This change resolves that by destroying all relevant states to reflect
the actual state during resume.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was missed in the previous fake sink change. The fake sink
allows us to enable a pipe with a disconnected display. We
shouldn't report it as connected.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous change moved link_disconnect_sink after dpcd read,
this causes the sink count to be overwritten which in turn causes
another detection to be triggered in the short pulse handler, which
brings down the display.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting on CNL we now need to map VBT DDC Pin to
BSPec DDC Pin values. Not a direct translation anymore.
According to VBT
Block 2 (General Bytes Definition)
DDC Bus
+----------+-----------+--------------------+
| DDI Type | VBT Value | Bspec Mapped Value |
+----------+-----------+--------------------+
| DDI-B | 0x1 | 0x1 |
| DDI-C | 0x2 | 0x2 |
| DDI-D | 0x3 | 0x4 |
| DDI-F | 0x4 | 0x3 |
+----------+-----------+--------------------+
v2: Move defines to a better place.
This is actually CNL_PCH not CNL only.
v3: Accepting Ville's suggestions: enums and array to
to make this future proof.
v4: Protect the array access as Ville suggested.
Also accepting all Jani's suggestions:
- use already defined gmbus pin definitions.
- use map_ddc_pin for disambiguation.
- Add /* sic */ comment on inverted values
so people can easily see it it nos a mistake
we have the map 3 -> 4 and 4 -> 3 :/
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171020172641.16029-1-rodrigo.vivi@intel.com
Place drm_event_vblank in a new union that includes that and a bare
drm_event structure. This will allow new members of that union to be
added in the future without changing code related to the existing vbl
event type.
Assignments to the crtc_id field are now done when the event is
allocated, rather than when delievered. This way, delivery doesn't
need to have the crtc ID available.
v2:
* Remove 'dev' argument from create_vblank_event
It wasn't being used anyways, and if we need it in the future,
we can always get it from crtc->dev.
* Check for MODESETTING before looking for crtc in queue_vblank_event
UMS drivers will oops if we try to get a crtc, so make sure
we're modesetting before we try to find a crtc_id to fill into
the event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit dc695b85fde88eca3ef3b03fcd82f15b6bc6e462)
This modifies the datatypes used by the vblank code to provide 64 bits
of vblank count.
The driver interfaces have been left using 32 bits of vblank count;
all of the code necessary to widen that value for the user API was
already included to handle devices returning fewer than 32-bits.
This will provide the necessary datatypes for the Vulkan API.
v2:
* Re-write wait_vblank ioctl to ABSOLUTE sequence
When an application uses the WAIT_VBLANK ioctl with RELATIVE
or NEXTONMISS bits set, the target vblank interval is updated
within the kernel. We need to write that target back to the
ioctl buffer and update the flags bits so that if the wait is
interrupted by a signal, when it is re-started, it will target
precisely the same vblank count as before.
* Leave driver API with 32-bit vblank count
v3:
* Rebase on top of Arnd Bergmann's patch which had
the switch to ktime_t parts.
[airlied: fix conflict with Ville vblank change].
Suggested-by: Michel Dänzer <michel@daenzer.net>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 2affbc16983e4fc90960bc7f70e7615f4228199b)
1,it should not work on non-SR-IOV case
2,the NO_VBIOS error is incorrect, should
handle it under detect_sriov_bios.
3,wrap the whole detect_sriov_bios with sriov check
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to support CEC the HDMI driver has to inform the CEC driver
whenever the physical address changes. So when the EDID is read the
CEC driver has to be informed and whenever the hotplug detect goes
away.
This is done through the cec-notifier framework.
The link between the HDMI driver and the CEC driver is done through
the hdmi-phandle property in the tegra-cec node in the device tree.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
