The ->reset_slot callback introduced by commits:
2e35afaefe ("PCI: pciehp: Add reset_slot() method") and
06a8d89af5 ("PCI: pciehp: Disable link notification across slot reset")
disables notification of Presence Detect Changed and Data Link Layer
State Changed events for the duration of a secondary bus reset.
However a bus reset not only triggers these events, but may also clear
the Presence Detect State bit in the Slot Status register and the Data
Link Layer Link Active bit in the Link Status register momentarily.
According to Sinan Kaya:
"I know for a fact that bus reset clears the Data Link Layer Active bit
as soon as link goes down. It gets set again following link up.
Presence detect depends on the HW implementation. QDT root ports
don't change presence detect for instance since nobody actually
removed the card. If an implementation supports in-band presence
detect, the answer is yes. As soon as the link goes down, presence
detect bit will get cleared until recovery."
https://lkml.kernel.org/r/42e72f83-3b24-f7ef-e5bc-290fae99259a@codeaurora.org
In-band presence detect is also covered in Table 4-15 in PCIe r4.0,
sec 4.2.6.
pciehp should therefore ensure that any parts of the driver that access
those bits do not run concurrently to a bus reset. The only precaution
the commits took to that effect was to halt interrupt polling. They
made no effort to drain the slot workqueue, cancel an outstanding
Attention Button work, or block slot enable/disable requests via sysfs
and in the ->probe hook.
Now that pciehp is converted to enable/disable the slot exclusively from
the IRQ thread, the only places accessing the two above-mentioned bits
are the IRQ thread and the ->probe hook. Add locking to serialize them
with a bus reset. This obviates the need to halt interrupt polling.
Do not add locking to the ->get_adapter_status sysfs callback to afford
users unfettered access to that bit. Use an rw_semaphore in lieu of a
regular mutex to allow parallel execution of the non-reset code paths
accessing the critical bits, i.e. the IRQ thread and the ->probe hook.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rajat Jain <rajatja@google.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Sinan Kaya <okaya@kernel.org>
Before the memory for the elfcorehdr is allocated the required size is
estimated with
alloc_size = 0x1000 + get_cpu_cnt() * 0x4a0 +
mem_chunk_cnt * sizeof(Elf64_Phdr);
Where 0x4a0 is used as size for the ELF notes to store the register
contend. This size is 8 bytes too small. Usually this does not immediately
cause a problem because the page reserved for overhead (Elf_Ehdr,
vmcoreinfo, etc.) is pretty generous. So usually there is enough spare
memory to counter the mis-calculated per cpu size. However, with growing
overhead and/or a huge cpu count the allocated size gets too small for the
elfcorehdr. Ultimately a BUG_ON is triggered causing the crash kernel to
panic.
Fix this by properly calculating the required size instead of relying on
magic numbers.
Fixes: a62bc07392 ("s390/kdump: add support for vector extension")
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we have a threaded interrupt with the handler being NULL, then
request_threaded_irq() -> __setup_irq() will complain and bail out if the
IRQF_ONESHOT flag isn't set. Therefore check for the handler being NULL
and set IRQF_ONESHOT in this case.
This change is needed to migrate the mei_me driver to
pci_alloc_irq_vectors() and pci_request_irq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
tracefs_ops is initialized inside tracefs_create_instance_dir and not
modified after. tracefs_create_instance_dir allows for initialization
only once, and is called from create_trace_instances(marked __init),
which is called from tracer_init_tracefs(marked __init). Also, mark
tracefs_create_instance_dir as __init.
Link: http://lkml.kernel.org/r/20180725171901.4468-1-zsm@chromium.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This patch detaches the preemptirq tracepoints from the tracers and
keeps it separate.
Advantages:
* Lockdep and irqsoff event can now run in parallel since they no longer
have their own calls.
* This unifies the usecase of adding hooks to an irqsoff and irqson
event, and a preemptoff and preempton event.
3 users of the events exist:
- Lockdep
- irqsoff and preemptoff tracers
- irqs and preempt trace events
The unification cleans up several ifdefs and makes the code in preempt
tracer and irqsoff tracers simpler. It gets rid of all the horrific
ifdeferry around PROVE_LOCKING and makes configuration of the different
users of the tracepoints more easy and understandable. It also gets rid
of the time_* function calls from the lockdep hooks used to call into
the preemptirq tracer which is not needed anymore. The negative delta in
lines of code in this patch is quite large too.
In the patch we introduce a new CONFIG option PREEMPTIRQ_TRACEPOINTS
as a single point for registering probes onto the tracepoints. With
this,
the web of config options for preempt/irq toggle tracepoints and its
users becomes:
PREEMPT_TRACER PREEMPTIRQ_EVENTS IRQSOFF_TRACER PROVE_LOCKING
| | \ | |
\ (selects) / \ \ (selects) /
TRACE_PREEMPT_TOGGLE ----> TRACE_IRQFLAGS
\ /
\ (depends on) /
PREEMPTIRQ_TRACEPOINTS
Other than the performance tests mentioned in the previous patch, I also
ran the locking API test suite. I verified that all tests cases are
passing.
I also injected issues by not registering lockdep probes onto the
tracepoints and I see failures to confirm that the probes are indeed
working.
This series + lockdep probes not registered (just to inject errors):
[ 0.000000] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/12:FAILED|FAILED| ok |
[ 0.000000] sirq-safe-A => hirqs-on/21:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + irqs-on/12:FAILED|FAILED| ok |
[ 0.000000] soft-safe-A + irqs-on/12:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + irqs-on/21:FAILED|FAILED| ok |
[ 0.000000] soft-safe-A + irqs-on/21:FAILED|FAILED| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
With this series + lockdep probes registered, all locking tests pass:
[ 0.000000] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/12: ok | ok | ok |
[ 0.000000] sirq-safe-A => hirqs-on/21: ok | ok | ok |
[ 0.000000] hard-safe-A + irqs-on/12: ok | ok | ok |
[ 0.000000] soft-safe-A + irqs-on/12: ok | ok | ok |
[ 0.000000] hard-safe-A + irqs-on/21: ok | ok | ok |
[ 0.000000] soft-safe-A + irqs-on/21: ok | ok | ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
Link: http://lkml.kernel.org/r/20180730222423.196630-4-joel@joelfernandes.org
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The HDLCD engine needs an active plane while the CRTC is active, as
it will start scanning out data from HDLCD_REG_FB_BASE once it gets
enabled. Make sure that the only available plane doesn't get disabled
while the CRTC remains active, as this will scanout invalid data.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The plane cleanup handler currently calls drm_plane_helper_disable(),
which is a legacy helper function. Replace it with a call to
drm_atomic_helper_shutdown() at removal time. The plane .destroy()
handler now consisting only of a call to drm_plane_cleanup(), replace it
with direct calls to that function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The top-level error handler calls drm_mode_config_cleanup() which will
destroy all planes. There's no need to destroy them manually in lower
error handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use drm_fb_cma_fbdev_init() and drm_fb_cma_fbdev_fini() which relies on
the fact that drm_device holds a pointer to the drm_fb_helper structure.
This means that the driver doesn't have to keep track of that.
Also use the drm_fb_helper functions directly.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Before:
libbpf: license of tools/perf/examples/bpf/etcsnoop.c is GPL
libbpf: section(6) version, size 4, link 0, flags 3, type=1
libbpf: kernel version of tools/perf/examples/bpf/etcsnoop.c is 41200
libbpf: section(7) .symtab, size 120, link 1, flags 0, type=2
bpf: config program 'syscalls:sys_enter_openat'
libbpf: load bpf program failed: Operation not permitted
libbpf: failed to load program 'syscalls:sys_enter_openat'
libbpf: failed to load object 'tools/perf/examples/bpf/etcsnoop.c'
bpf: load objects failed
After: (just the last line changes)
bpf: load objects failed: err=-4009: (Incorrect kernel version)
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-wi44iid0yjfht3lcvplc75fm@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The integration of the Designware SPI controller on Microsemi SoCs requires
an extra register set to be able to give the IP control of the SPI
interface.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix return code check for "max brightness" ACPI call.
The Dell laptop ACPI video brightness control is not present on dell
laptops anymore, but was present in older kernel versions.
The code that checks the return value is incorrect since the SMM
refactoring.
The old code was:
if (buffer->output[0] == 0)
Which was changed to:
ret = dell_send_request(...)
if (ret)
However, dell_send_request() will return 0 if buffer->output[0] == 0,
so we must change the check to:
if (ret == 0)
This issue was found on a Dell M4800 laptop, and the fix tested on it
as well.
Fixes: 549b4930f0 ("dell-smbios: Introduce dispatcher for SMM calls")
Signed-off-by: Damien Thébault <damien@dtbo.net>
Tested-by: Damien Thébault <damien@dtbo.net>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
PMU event descriptions use 7 spaces + '[' or 8 spaces as indentation.
Metric groups used a tab + '['. This patch unifies it to the way PMU
event descriptions are indented.
BEFORE:
$ perf list
[...]
Metric Groups:
DSB:
DSB_Coverage
[Fraction of Uops delivered by the DSB (aka Decoded Icache; or Uop Cache)]
[...]
AFTER:
$ perf list
[...]
Metric Groups:
DSB:
DSB_Coverage
[Fraction of Uops delivered by the DSB (aka Decoded Icache; or Uop Cache)]
[...]
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Kim Phillips <kim.phillips@arm.com>
LPU-Reference: 771439042.22924766.1532986504631.JavaMail.zimbra@redhat.com
Link: https://lkml.kernel.org/n/tip-mlo850517m6u1rbjndvd1bwr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The perf tool build and install is controlled via a Makefile. The
'install' rule creates directories and copies files. Among them are
header files installed in /usr/lib/include/perf/bpf/.
However all listed examples are installing its header files in
/usr/lib/<tool-name>/...[/include]/header.h
and not in
/usr/lib/include/<tool-name>/.../header.h.
Background information:
Building the Fedora 28 glibc RPM on s390x and s390 fails on s390 (gcc
-m31) as gcc is not able to find header-files like stdbool.h.
In the glibc.spec file, you can see that glibc is configured with
"--with-headers". In this case, first -nostdinc is added to the CFLAGS
and then further include paths are added via -isystem. One of those
paths should contain header files like stdbool.h.
In order to get this path, gcc is invoked with:
- on Fedora 28 (with 4.18 kernel):
$ gcc -print-file-name=include
/usr/lib/gcc/s390x-redhat-linux/8/include
$ gcc -m31 -print-file-name=include
/usr/lib/gcc/s390x-redhat-linux/8/../../../../lib/include
=> If perf is installed, this is: /usr/lib/include
On my machine this directory is only containing the directory "perf".
If perf is not installed gcc returns: /usr/lib/gcc/s390x-redhat-linux/8/include
- on Ubuntu 18.04 (with 4.15 kernel):
$ gcc -print-file-name=include
/usr/lib/gcc/s390x-linux-gnu/7/include
$ gcc -m31 -print-file-name=include
/usr/lib/gcc/s390x-linux-gnu/7/include
=> gcc returns the correct path even if perf is installed.
In each case, the introduction of the subdirectory /usr/lib/include
leads to the regression that one can not build the glibc RPM for s390
anymore as gcc can not find headers like stdbool.h.
To remedy this install bpf.h to /usr/lib/perf/include/bpf/bpf.h
Output before using the command 'perf test -Fv 40':
echo '...[bpf-program-source]...' | /usr/bin/clang ... \
-I/root/lib/include/perf/bpf ...
^^^^^^^^^^^^
...
[root@p23lp27 perf]# perf test -F 40
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : Ok
[root@p23lp27 perf]#
Output after using command 'perf test -Fv 40':
echo '...[bpf-program-source]...' | /usr/bin/clang ... \
-I/root/lib/perf/include/bpf ...
^^^^^^^^^^^^
...
[root@p23lp27 perf]# perf test -F 40
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : Ok
[root@p23lp27 perf]#
Committer testing:
While the above 'perf test -F 40' (or 'perf test bpf') will allow us
to see that the correct path is now added via -I, to actually test this
we better try to use a bpf script that includes files in the changed
directory.
We have the files that now reside in /root/lib/perf/examples/bpf/ to do
just that:
# tail -8 /root/lib/perf/examples/bpf/5sec.c
#include <bpf.h>
int probe(hrtimer_nanosleep, rqtp->tv_sec)(void *ctx, int err, long sec)
{
return sec == 5;
}
license(GPL);
# perf trace -e *sleep -e /root/lib/perf/examples/bpf/5sec.c sleep 4
0.333 (4000.086 ms): sleep/9248 nanosleep(rqtp: 0x7ffc155f3300) = 0
# perf trace -e *sleep -e /root/lib/perf/examples/bpf/5sec.c sleep 5
0.287 ( ): sleep/9659 nanosleep(rqtp: 0x7ffeafe38200) ...
0.290 ( ): perf_bpf_probe:hrtimer_nanosleep:(ffffffff9911efe0) tv_sec=5
0.287 (5000.059 ms): sleep/9659 ... [continued]: nanosleep()) = 0
# perf trace -e *sleep -e /root/lib/perf/examples/bpf/5sec.c sleep 6
0.247 (5999.951 ms): sleep/10068 nanosleep(rqtp: 0x7fff2086d900) = 0
# perf trace -e *sleep -e /root/lib/perf/examples/bpf/5sec.c sleep 5.987
0.293 ( ): sleep/10489 nanosleep(rqtp: 0x7ffdd4fc10e0) ...
0.296 ( ): perf_bpf_probe:hrtimer_nanosleep:(ffffffff9911efe0) tv_sec=5
0.293 (5986.912 ms): sleep/10489 ... [continued]: nanosleep()) = 0
#
Suggested-by: Stefan Liebler <stli@linux.ibm.com>
Suggested-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes: 1b16fffa38 ("perf llvm-utils: Add bpf include path to clang command line")
Link: http://lkml.kernel.org/r/20180731073254.91090-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf c2c' scans read/write accesses and tries to find false sharing
cases, so when the events it wants were not asked for or ended up not
taking place, we get no histograms.
So do not try to display entry details if there's not any. Currently
this ends up in crash:
$ perf c2c report # then press 'd'
perf: Segmentation fault
$
Committer testing:
Before:
Record a perf.data file without events of interest to 'perf c2c report',
then call it and press 'd':
# perf record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data (6 samples) ]
# perf c2c report
perf: Segmentation fault
-------- backtrace --------
perf[0x5b1d2a]
/lib64/libc.so.6(+0x346df)[0x7fcb566e36df]
perf[0x46fcae]
perf[0x4a9f1e]
perf[0x4aa220]
perf(main+0x301)[0x42c561]
/lib64/libc.so.6(__libc_start_main+0xe9)[0x7fcb566cff29]
perf(_start+0x29)[0x42c999]
#
After the patch the segfault doesn't take place, a follow up patch to
tell the user why nothing changes when 'd' is pressed would be good.
Reported-by: rodia@autistici.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: f1c5fd4d0b ("perf c2c report: Add TUI cacheline browser")
Link: http://lkml.kernel.org/r/20180724062008.26126-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Recently, the subtest numbering was changed to start from 1. While it
is fine for displaying results, this should not be the case when the
subtests are actually invoked.
Typically, the subtests are stored in zero-indexed arrays and invoked
based on the index passed to the main test function. Since the index
now starts from 1, the second subtest in the array (index 1) gets
invoked instead of the first (index 0). This applies to all of the
following subtests but for the last one, the subtest always fails
because it does not meet the boundary condition of the subtest index
being lesser than the number of subtests.
This can be observed on powerpc64 and x86_64 systems running Fedora 28
as shown below.
Before:
# perf test "builtin clang support"
55: builtin clang support :
55.1: builtin clang compile C source to IR : Ok
55.2: builtin clang compile C source to ELF object : FAILED!
# perf test "LLVM search and compile"
38: LLVM search and compile :
38.1: Basic BPF llvm compile : Ok
38.2: kbuild searching : Ok
38.3: Compile source for BPF prologue generation : Ok
38.4: Compile source for BPF relocation : FAILED!
# perf test "BPF filter"
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : FAILED!
After:
# perf test "builtin clang support"
55: builtin clang support :
55.1: builtin clang compile C source to IR : Ok
55.2: builtin clang compile C source to ELF object : Ok
# perf test "LLVM search and compile"
38: LLVM search and compile :
38.1: Basic BPF llvm compile : Ok
38.2: kbuild searching : Ok
38.3: Compile source for BPF prologue generation : Ok
38.4: Compile source for BPF relocation : Ok
# perf test "BPF filter"
40: BPF filter :
40.1: Basic BPF filtering : Ok
40.2: BPF pinning : Ok
40.3: BPF prologue generation : Ok
40.4: BPF relocation checker : Ok
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Fixes: 9ef0112442 ("perf test: Fix subtest number when showing results")
Link: http://lkml.kernel.org/r/20180726171733.33208-1-sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For instance:
$ trace -e socket* ssh sandy
0.000 ( 0.031 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
0.052 ( 0.015 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
1.568 ( 0.020 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
1.603 ( 0.012 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
1.699 ( 0.014 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
1.724 ( 0.012 ms): ssh/19919 socket(family: LOCAL, type: STREAM|CLOEXEC|NONBLOCK ) = 3
1.804 ( 0.020 ms): ssh/19919 socket(family: INET, type: STREAM, protocol: TCP ) = 3
17.549 ( 0.098 ms): ssh/19919 socket(family: LOCAL, type: STREAM ) = 4
acme@sandy's password:
Just like with other syscall args, the common bits are supressed so that
the output is more compact, i.e. we use "TCP" instead of "IPPROTO_TCP",
but we can make this show the original constant names if we like it by
using some command line knob or ~/.perfconfig "[trace]" section
variable.
Also needed is to make perf's event parser accept things like:
$ perf trace -e socket*/protocol=TCP/
By using both the tracefs event 'format' files and these tables built
from the kernel sources.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-l39jz1vnyda0b6jsufuc8bz7@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We may have string tables where not all slots have values, in those
cases its better to print the numeric value, for instance:
In the table below we would show "protocol: (null)" for
socket_ipproto[3]
Where it would be better to show "protocol: 3".
$ tools/perf/trace/beauty/socket_ipproto.sh
static const char *socket_ipproto[] = {
[0] = "IP",
[103] = "PIM",
[108] = "COMP",
[12] = "PUP",
[132] = "SCTP",
[136] = "UDPLITE",
[137] = "MPLS",
[17] = "UDP",
[1] = "ICMP",
[22] = "IDP",
[255] = "RAW",
[29] = "TP",
[2] = "IGMP",
[33] = "DCCP",
[41] = "IPV6",
[46] = "RSVP",
[47] = "GRE",
[4] = "IPIP",
[50] = "ESP",
[51] = "AH",
[6] = "TCP",
[8] = "EGP",
[92] = "MTP",
[94] = "BEETPH",
[98] = "ENCAP",
};
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-7djfak94eb3b9ltr79cpn3ti@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It'll use tools/include copy of linux/in.h to generate a table to be
used by tools, initially by the 'socket' and 'socketpair' beautifiers in
'perf trace', but that could also be used to translate from a string
constant to the integer value to be used in a eBPF or tracefs tracepoint
filter.
When used without any args it produces:
$ tools/perf/trace/beauty/socket_ipproto.sh
static const char *socket_ipproto[] = {
[0] = "IP",
[103] = "PIM",
[108] = "COMP",
[12] = "PUP",
[132] = "SCTP",
[136] = "UDPLITE",
[137] = "MPLS",
[17] = "UDP",
[1] = "ICMP",
[22] = "IDP",
[255] = "RAW",
[29] = "TP",
[2] = "IGMP",
[33] = "DCCP",
[41] = "IPV6",
[46] = "RSVP",
[47] = "GRE",
[4] = "IPIP",
[50] = "ESP",
[51] = "AH",
[6] = "TCP",
[8] = "EGP",
[92] = "MTP",
[94] = "BEETPH",
[98] = "ENCAP",
};
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-v9rafqh3qn6b9kp9vfvj9f8s@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 'umask' event parameter is unsupported on some architectures like
powerpc64.
This can be observed on a powerpc64le system running Fedora 27 as shown
below.
# perf test "Parse event definition strings" -v
6: Parse event definition strings :
--- start ---
test child forked, pid 45915
...
running test 3 'cpu/name='COMPLEX_CYCLES_NAME:orig=cycles,desc=chip-clock-ticks',period=0x1,event=0x2,umask=0x3/ukp'Invalid event/parameter 'umask'
Invalid event/parameter 'umask'
failed to parse event 'cpu/name='COMPLEX_CYCLES_NAME:orig=cycles,desc=chip-clock-ticks',period=0x1,event=0x2,umask=0x3/ukp', err 1, str 'unknown term'
event syntax error: '..,event=0x2,umask=0x3/ukp'
\___ unknown term
valid terms: event,mark,pmc,cache_sel,pmcxsel,unit,thresh_stop,thresh_start,combine,thresh_sel,thresh_cmp,sample_mode,config,config1,config2,name,period,freq,branch_type,time,call-graph,stack-size,no-inherit,inherit,max-stack,no-overwrite,overwrite,driver-config
mem_access -> cpu/event=0x10401e0/
running test 0 'config=10,config1,config2=3,umask=1'
test child finished with 1
---- end ----
Parse event definition strings: FAILED!
Committer testing:
After applying the patch these test passes and in verbose mode we get:
# perf test -v "event definition"
6: Parse event definition strings:
--- start ---
test child forked, pid 11061
running test 0 'syscalls:sys_enter_openat'Using CPUID GenuineIntel-6-9E
<SNIP>
running test 53 'cycles/name='COMPLEX_CYCLES_NAME:orig=cycles,desc=chip-clock-ticks'/Duk'
running test 0 'cpu/config=10,config1,config2=3,period=1000/u'
running test 1 'cpu/config=1,name=krava/u,cpu/config=2/u'
running test 2 'cpu/config=1,call-graph=fp,time,period=100000/,cpu/config=2,call-graph=no,time=0,period=2000/'
running test 3 'cpu/name='COMPLEX_CYCLES_NAME:orig=cycles,desc=chip-clock-ticks',period=0x1,event=0x2/ukp'
<SNIP>
test child finished with 0
---- end ----
Parse event definition strings: Ok
#
Suggested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Fixes: 06dc5bf21f ("perf tests: Check that complex event name is parsed correctly")
Link: http://lkml.kernel.org/r/20180726105502.31670-1-sandipan@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make use of UAC3 Power Domains associated to an Audio Streaming
path within the PCM's logic. This means, when there is no audio
being transferred (pcm is closed), the host will set the Power Domain
associated to that substream to state D1. When audio is being transferred
(from hw_params onwards), the Power Domain will be set to D0 state.
This is the way the host lets the device know which Terminal
is going to be actively used and it is for the device to
manage its own internal resources on that UAC3 Power Domain.
Note the resume method now sets the Power Domain to D1 state as
resuming the device doesn't mean audio streaming will occur.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the UAC3 Power Domain state for an Audio Streaming interface
to D2 state before suspending the device (usb_driver callback).
This lets the device know there is no intention to use any of the
Units in the Audio Function and that the host is not going to
even listen for wake-up events (interrupts) on the units.
When the usb_driver gets resumed, the state D0 (fully powered) will
be set. This ties up the UAC3 Power Domains to the runtime PM.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Power Domains in the UAC3 spec are mainly intended to be
associated to an Input or Output Terminal so the host
changes the power state of the entire capture or playback
path within the topology.
This patch adds support for finding Power Domains associated
to an Audio Streaming Interface (bTerminalLink) and adds a
reference to them in the usb audio substreams (snd_usb_substream).
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thee USB Audio Class 3 (UAC3) introduces Power Domains as a new
feature to let a host turn individual parts of an audio function
to different power states via USB requests. This lets the device
get to know a bit amore about what the host is up to in order to
optimize power consumption efficiently.
The Power Domains are optional for UAC3 configuration but all
UAC3 devices shall include at least one BADD configuration where
the support for Power Domains is compulsory.
This patch adds a set of features/helpers to parse these power
domains and change their status.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'perf record' will error out if both --delay and LBR are applied.
For example:
# perf record -D 1000 -a -e cycles -j any -- sleep 2
Error:
dummy:HG: PMU Hardware doesn't support sampling/overflow-interrupts.
Try 'perf stat'
#
A dummy event is added implicitly for initial delay, which has the same
configurations as real sampling events. The dummy event is a software
event. If LBR is configured, perf must error out.
The dummy event will only be used to track PERF_RECORD_MMAP while perf
waits for the initial delay to enable the real events. The BRANCH_STACK
bit can be safely cleared for the dummy event.
After applying the patch:
# perf record -D 1000 -a -e cycles -j any -- sleep 2
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 1.054 MB perf.data (828 samples) ]
#
Reported-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1531145722-16404-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Calling pmull_gcm_encrypt_block() requires kernel_neon_begin() and
kernel_neon_end() to be used since the routine touches the NEON
register file. Add the missing calls.
Also, since NEON register contents are not preserved outside of
a kernel mode NEON region, pass the key schedule array again.
Fixes: 7c50136a8a ("crypto: arm64/aes-ghash - yield NEON after every ...")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we understand the deadlock arising from flush_icache_range()
on the kexec crash kernel path, add a comment to justify the use of
__flush_icache_range() here.
Reported-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The SDEI stack helper functions are only used by _on_sdei_stack() and
refer to symbols (e.g. sdei_stack_normal_ptr) that are only defined if
CONFIG_VMAP_STACK=y.
Mark these functions as static, so we don't run into errors at link-time
due to references to undefined symbols. Stick all the parameters onto
the same line whilst we're passing through.
Signed-off-by: Will Deacon <will.deacon@arm.com>
drivers/video/fbdev/omap2/omapfb/dss/core.c:141:2-26: WARNING: NULL check before some freeing functions is not needed.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
drivers/video/fbdev/omap2/omapfb/dss/dss_features.c:895:2-5: WARNING: Use BUG_ON instead of if condition followed by BUG.
Please make sure the condition has no side effects (see conditional BUG_ON definition in include/asm-generic/bug.h)
Use BUG_ON instead of a if condition followed by BUG.
Semantic patch information:
This makes an effort to find cases where BUG() follows an if
condition on an expression and replaces the if condition and BUG()
with a BUG_ON having the conditional expression of the if statement
as argument.
Generated by: scripts/coccinelle/misc/bugon.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
drivers/video/fbdev/omap2/omapfb/omapfb-main.c:290:9-10: WARNING: return of 0/1 in function 'cmp_var_to_colormode' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 7378f11498 ("media: omap2: omapfb: allow building it with COMPILE_TEST")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fix build warning when built as a loadable module.
amifb_setup() and amifb_setup_mcap() are only needed when the driver
is builtin.
This matches how the functions are called (using #ifndef MODULE).
../drivers/video/fbdev/amifb.c:2344:19: warning: 'amifb_setup' defined but not used [-Wunused-function]
static int __init amifb_setup(char *options)
../drivers/video/fbdev/amifb.c:2307:20: warning: 'amifb_setup_mcap' defined but not used [-Wunused-function]
static void __init amifb_setup_mcap(char *spec)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
If the console is unlocked during registration, the console subsystem
generates significant amounts of warnings, which obfuscate actual
debugging messages. Setting ignore_console_lock_warning while debugging
console registration avoid the noise.
v3:
- manipulate ignore_console_lock_warning with atomic_{inc,dec}
v2:
- restore ignore_console_lock_warning if lock_fb_info() fails
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The macro WARN_CONSOLE_UNLOCKED prints a warning when a thread enters
the console's critical section without having acquired the console
lock. The console lock can be ignored when debugging the console using
printk, but this makes WARN_CONSOLE_UNLOCKED generate unnecessary
warnings.
The variable ignore_console_lock_warning temporarily disables
WARN_CONSOLE_UNLOCKED. Developers interested in debugging the console's
critical sections should increment it before entering the CS and
decrement it after leaving the CS. Setting ignore_console_lock_warning
is only for debugging. Regular operation should not manipulate it.
Acknoledgements: This patch is based on an earlier version by Steven
Rostedt. The use of atomic increment/decrement was suggested by Petr
Mladek.
Link: http://lkml.kernel.org/r/717e6337-e7a6-7a92-1c1b-8929a25696b5@suse.de
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
[b.zolnierkie: use <linux/atomic.h>]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
EEH recovery currently fails on pSeries for some IOV capable PCI
devices, if CONFIG_PCI_IOV is on and the hypervisor doesn't provide
certain device tree properties for the device. (Found on an IOV
capable device using the ipr driver.)
Recovery fails in pci_enable_resources() at the check on r->parent,
because r->flags is set and r->parent is not. This state is due to
sriov_init() setting the start, end and flags members of the IOV BARs
but the parent not being set later in
pseries_pci_fixup_iov_resources(), because the
"ibm,open-sriov-vf-bar-info" property is missing.
Correct this by zeroing the resource flags for IOV BARs when they
can't be configured (this is the same method used by sriov_init() and
__pci_read_base()).
VFs cleared this way can't be enabled later, because that requires
another device tree property, "ibm,number-of-configurable-vfs" as well
as support for the RTAS function "ibm_map_pes". These are all part of
hypervisor support for IOV and it seems unlikely that a hypervisor
would ever partially, but not fully, support it. (None are currently
provided by QEMU/KVM.)
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Bryant G. Ly <bryantly@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL firmware provides the facility for some groups of sensors to be
enabled/disabled at runtime to give the user the option of using the
system resources for collecting these sensors or not.
For example, on POWER9 systems, the On Chip Controller (OCC) gathers
various system and chip level sensors and maintains their values in
main memory.
This patch provides support for enabling/disabling the sensor groups
like power, temperature, current and voltage.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
[stewart@linux.vnet.ibm.com: Commit message]
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Adds support to enable/disable a sensor group at runtime. This
can be used to select the sensor groups that needs to be copied to
main memory by OCC. Sensor groups like power, temperature, current,
voltage, frequency, utilization can be enabled/disabled at runtime.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export pnv_idle_states and nr_pnv_idle_states so that its accessible to
cpuidle driver. Use properties from pnv_idle_states structure for powernv
cpuidle_init.
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
