Clear test_mode flag when the gadget is reset by host, otherwise
will affect the next test item.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset EP when disable it to reset data toggle for U2 EP, and
SeqN, flow control status etc for U3 EP, this can avoid
issue of uncontinuous SeqN
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the controller receives a LPM request, it will reject the LPM
request, and need software to re-enable it after LPM resume if the
controller doesn't remote wakeup from L1 automatically
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable compliance transition for a port by writing "compliance" to the
ports portsc file in debugfs.
port must be "Not-connected" and Link must be in RxDetect state to enable
compliance mode.
Only needed for host that have CTC flag set.
Allows state transitioning to compliance at 1st LFPS timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ports/portxx/portsc for each xHC hardware usb port to debugfs.
Showing the content of the port status and control register for
each port (PORTSC)
Portxx is numbered starting from 1 for historical reasons to better
match port numbering shown by lsusb and other places.
Ports in debugfs are in the order XHC controller has them,
In most cases USB2 ports come first, followed by USB3 ports.
i.e. USB2 ports are port01-portxx, and USB3 portxx-portmax.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are now using the new port strtuctes the port_arrays
are no longer needed, remove them completely
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd_portnum is a better desctiption than faked_port_index, and
is in line with the name the port structure uses.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use port structures in the port event handler.
Getting the right hcd and hcd portnumber from the hardware port number
is a lot easier with port structures, and allows us to remove a lot
of the previous code, including the find_faked_portnum_from_hw_index()
function
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for HiSilicon STB xHCI host controller.
There are two xHCI host controllers on HiSilicon STB SoCs. Each
one requires additional configuration before exposing interface
compliant with xHCI.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPUID bits of OSXSAVE (function=0x1) and OSPKE (func=0x7, leaf=0x0)
allows user apps to detect if OS has set CR4.OSXSAVE or CR4.PKE. KVM is
supposed to update these CPUID bits when CR4 is updated. Current KVM
code doesn't handle some special cases when updates come from emulator.
Here is one example:
Step 1: guest boots
Step 2: guest OS enables XSAVE ==> CR4.OSXSAVE=1 and CPUID.OSXSAVE=1
Step 3: guest hot reboot ==> QEMU reset CR4 to 0, but CPUID.OSXAVE==1
Step 4: guest os checks CPUID.OSXAVE, detects 1, then executes xgetbv
Step 4 above will cause an #UD and guest crash because guest OS hasn't
turned on OSXAVE yet. This patch solves the problem by comparing the the
old_cr4 with cr4. If the related bits have been changed,
kvm_update_cpuid() needs to be called.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Pull block fixes from Jens Axboe:
"Two fixes that should go into this release:
- a loop writeback error clearing fix from Jeff
- the sr sense fix from myself"
* tag 'for-linus-20180524' of git://git.kernel.dk/linux-block:
loop: clear wb_err in bd_inode when detaching backing file
sr: pass down correctly sized SCSI sense buffer
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now pass a GPIO descriptor to the core instead of a global
GPIO number, if this descriptor is NULL the GPIO line is not
used. Just delete the assignment of an invalid GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
All users of this regulator use device tree so the transition is
pretty smooth.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
This driver has supported passing a LDO enable GPIO for years,
yet this facility has never been put to use in the upstream kernel.
If someone desires to put in place GPIO control for the LDOs,
this can be done by adding a GPIO descriptor table in the MFD
nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
MFD children, or using a board file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_optional() call.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull power management fix from Rafael Wysocki:
"Fix a regression from the 4.15 cycle that caused the system suspend
and resume overhead to increase on many systems and triggered more
serious problems on some of them (Rafael Wysocki)"
* tag 'pm-4.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / core: Fix direct_complete handling for devices with no callbacks
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
* tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Explicitly set source e-switch in offloaded TC rules
net/mlx5: Add source e-switch owner
net/mlx5e: Explicitly set destination e-switch in FDB rules
net/mlx5: Add destination e-switch owner
net/mlx5: Properly handle a vport destination when setting FTE
net/mlx5: Add merged e-switch cap
IB/mlx5: Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Eswitch, Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Vport, Use 'kvfree()' for memory allocated by 'kvzalloc()'
There are several places a gid table is accessed.
Have a helper tiny function rdma_gid_table() to avoid code
duplication at such places.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead of open coding memcmp() to check whether a given GID is zero or
not, use a helper function to do so, and replace instances of
memcpy(z,&zgid) with memset.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
On fatal error the driver simulates CQE's for ULPs that rely on
completion of all their posted work-request.
For the GSI traffic, the mlx5 has its own mechanism that sends the
completions via software CQE's directly to the relevant CQ.
This should be kept in fatal error too, so the driver should simulate
such CQE's with the specified error state in order to complete GSI QP
work requests.
Without the fix the next deadlock might appears:
schedule_timeout+0x274/0x350
wait_for_common+0xec/0x240
mcast_remove_one+0xd0/0x120 [ib_core]
ib_unregister_device+0x12c/0x230 [ib_core]
mlx5_ib_remove+0xc4/0x270 [mlx5_ib]
mlx5_detach_device+0x184/0x1a0 [mlx5_core]
mlx5_unload_one+0x308/0x340 [mlx5_core]
mlx5_pci_err_detected+0x74/0xe0 [mlx5_core]
Cc: <stable@vger.kernel.org> # 4.7
Fixes: 89ea94a7b6 ("IB/mlx5: Reset flow support for IB kernel ULPs")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In commit 357d23c811a7 ("Remove the obsolete libibcm library")
in rdma-core [1], we removed obsolete library which used the
/dev/infiniband/ucmX interface.
Following multiple syzkaller reports about non-sanitized
user input in the UCMA module, the short audit reveals the same
issues in UCM module too.
It is better to disable this interface in the kernel,
before syzkaller team invests time and energy to harden
this unused interface.
[1] https://github.com/linux-rdma/rdma-core/pull/279
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Remove duplicate declaration of gid_cache_wq.
Fixes: d41861942 ("IB/core: Add generic function to extract IB speed from netdev")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The lower 15 bit of paramter of db structure means different
meanings when db type is sq, rq and srq.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Given we are dealing with nano-second level timers, when the timer
pops, ensure it happens on the CPU which caused the timer to be set
in the first place. This avoids excessive jitter from the desired
expiration time by avoiding the cost of switching our context to
another CPU that is cache cold for this given timer.
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The knowledge of the internal workings of the expect receive
is too distributed.
Fix by:
- right size several rcd fields associated with
expect receive
- making an init entrance to init all the lists
- consolidate all the allocations into an array anchored
in the rcd
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
16B Management Packets (L4=0x08) replace the BTH and DETH
of normal MAD packet packets with a header containing the
the source and destination queue pair numbers; fields that
were originally retrieved from the BTH/DETH are now populated
from this header as well as from the 16B LRH (e.g. pkey).
16B Management Packets are used as an optimized management
format on 16B fabrics.
These management packets have an opcode of IB_OPCODE_UD_SEND_ONLY,
a fixed 3Byte pad, and a header length of 24Bytes.
The decision as to when we send a management packet is based
upon either the source or destination queue pair number being
0 or 1.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add 16B Management Packet definition. This optimized packet
format replaces the ib_other_headers and BTH with a source
and destination QP number.
To support these packets we introduce struct opa_16b_mgmt
into the struct hfi1_16b_header.
This packet format is only used for MAD packets using the
IB_OPCODE_UD_SEND_ONLY opcode on QP0/1.
The original 16B implementation failed to use 16B management
packets so now we add their definition.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a table of important fields from the fw_ri_tpte structure to the mr
resource tracking table. This is helpful in debugging.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
