On RX and TX interrupts, check for the WCN36XX_CH_STAT_INT_ED_MASK or
WCN36XX_CH_STAT_INT_DONE_MASK in the interrupt reason register, and
only handle packets when it is set. This way, reap_tx_dxes() is only
invoked when needed.
This brings the dequeing logic in line with what the prima downstream
driver is doing.
While at it, also log the interrupt reason.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like on the TX side, check for the interrupt reason when the RX interrupt
is latched and clear the ERR, DONE and ED masks.
This seems to help with connection timeouts and network stream
starvatations. And FWIW, the downstream driver does the same thing.
Note that in analogy to the TX side, WCN36XX_DXE_0_INT_CLR should be set to
WCN36XX_INT_MASK_CHAN_RX_{L,H} rather than WCN36XX_DXE_INT_CH{1,3}_MASK. It
did the right thing however, as the defines happen to have identical values.
Also, instead of determining register addresses and values inside
wcn36xx_rx_handle_packets(), pass them as arguments.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no need to disable the IRQ from inside its handler.
Instead just grab the spinlock of the channel that is being processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device takes 32-bit addresses only, so inform the DMA API about it.
This is the default on msm8016, so that doesn't change anything, but
it's best practice to be explicit.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() is entered while the device is still processing
the queue asyncronously, we are racing against the firmware code with
updates to the buffer descriptors. Presumably, the firmware scans the ring
buffer that holds the descriptors and scans for a valid control descriptor,
and then assumes that the next descriptor contains the payload. If, however,
the control descriptor is marked valid, but the payload descriptor isn't,
the packet is not sent out.
Another issue with the current code is that is lacks memory barriers before
descriptors are marked valid. This is important because the CPU may reorder
writes to memory, even if it is allocated as coherent DMA area, and hence
the device may see incompletely written data.
To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so
that the payload descriptor is made valid before the control descriptor.
Memory barriers are added to ensure coherency of shared memory areas.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: FCC -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.
Supported Chipsets:
-QCA988X/QCA9887 PCI
-QCA99X0/QCA9984/QCA9888/QCA4019 PCI
-QCA6174/QCA9377 PCI/USB/SDIO
-WCN3990 SNOC
Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.
Tested on:
QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On platforms where the Low Power S0 Idle _DSM interface is used,
on wakeup from suspend-to-idle, when it is known that the ACPI SCI
has triggered while suspended, dispatch the EC GPE in order to catch
all EC events that may have triggered the wakeup before carrying out
the noirq phase of device resume.
That is needed to handle power button wakeup on some platforms where
the EC goes into a low-power mode during suspend-to-idle and while in
that mode it will discard events after a timeout. If that timeout is
shorter than the time it takes to complete the noirq resume of
devices, looking for EC events after the latter is too late.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
Introduce acpi_dispatch_gpe() as a wrapper around acpi_ev_detect_gpe()
for checking if the given GPE (as represented by a GPE device handle
and a GPE number) is currently active and dispatching it (if that's
the case) outside of interrupt context.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Comment explanning the raw event code encoding for Power8 was
moved to isa207_common.h file when re-factoring the code to
support power9. But then Power9 pmu branched out due to changes
specific to power9. So move the encoding comment back to power8-pmu.c
Just comment movement and no logic change.
Fixes: 4d3576b207 ('powerpc/perf: factor out power8 pmu macros and defines')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide __dasd_cancel_req that is called with the ccw device lock
held to simplify the locking in dasd_times_out. Also this removes
the following sparse warning:
context imbalance in 'dasd_times_out' - different lock contexts for basic block
Note: with this change dasd_schedule_device_bh is now called (via
dasd_cancel_req) with the ccw device lock held. But is is already
the case for other codepaths.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
