skb->offload_fwd_mark and dev->offload_fwd_mark are 32-bit and should be
unique for device and may even be unique for a sub-set of ports within
device, so add switchdev helper function to generate unique marks based on
port's switch ID and group_ifindex. group_ifindex would typically be the
container dev's ifindex, such as the bridge's ifindex.
The generator uses a global hash table to store offload_fwd_marks hashed by
{switch ID, group_ifindex} key.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just before queuing skb for xmit on port, check if skb has been marked by
switchdev port driver as already fordwarded by device. If so, drop skb. A
non-zero skb->offload_fwd_mark field is set by the switchdev port
driver/device on ingress to indicate the skb has already been forwarded by
the device to egress ports with matching dev->skb_mark. The switchdev port
driver would assign a non-zero dev->offload_skb_mark for each device port
netdev during registration, for example.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts 19424e052f ("sit:
Add gro callbacks to sit_offload") because it generates packets
that cannot be handled even by our own GSO.
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
net/bridge/br_if.c: In function 'br_dev_delete':
>> net/bridge/br_if.c:284:2: error: implicit declaration of function
>> 'br_multicast_dev_del' [-Werror=implicit-function-declaration]
br_multicast_dev_del(br);
^
cc1: some warnings being treated as errors
when igmp snooping is not defined.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly created flows don't have flowi6_oif set (at least if the
associated socket is not interface-bound). This leads to a mismatch in
__xfrm6_selector_match() for policies which specify an interface in the
selector (sel->ifindex != 0).
Backtracing shows this happens in code-paths originating from e.g.
ip6_datagram_connect(), rawv6_sendmsg() or tcp_v6_connect(). (UDP was
not tested for.)
In summary, this patch fixes policy matching on outgoing interface for
locally generated packets.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge (or port) is brought down/up flush only temp entries and
leave the perm ones. Flush perm entries only when deleting the bridge
device or the associated port.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group notifications were not sent when a group expired or was deleted
due to bridge/port device being deleted. So add br_mdb_notify() to
br_multicast_del_pg().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It would be very useful to retrieve the net_cls's classid from an eBPF
program to allow for a more fine-grained classification, it could be
directly used or in conjunction with additional policies. I.e. docker,
but also tooling such as cgexec, can easily run applications via net_cls
cgroups:
cgcreate -g net_cls:/foo
echo 42 > foo/net_cls.classid
cgexec -g net_cls:foo <prog>
Thus, their respecitve classid cookie of foo can then be looked up on
the egress path to apply further policies. The helper is desigend such
that a non-zero value returns the cgroup id.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out retrieving the cgroups net_cls classid retrieval into its
own function, so that it can be reused later on from other parts of
the traffic control subsystem. If there's no skb->sk, then the small
helper returns 0 as well, which in cls_cgroup terms means 'could not
classify'.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0bf4828983 ("svcrdma: refactor marshalling logic") removed
the last call site for svc_rdma_fastreg().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Kernel coding conventions frown upon having large nontrivial
functions in header files, and the preference these days is to
allow the compiler to make inlining decisions if possible.
As these functions are re-homed into a .c file, be sure that
comparisons with fields in struct rpcrdma_msg are with be32
constants.
This is a refactoring change; no behavior change is intended.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The Linux NFS server returns garbage in the data payload of inline
NFS/RDMA READ replies. These are READs of under 1000 bytes or so
where the client has not provided either a reply chunk or a write
list.
The NFS server delivers the data payload for an NFS READ reply to
the transport in an xdr_buf page list. If the NFS client did not
provide a reply chunk or a write list, send_reply() is supposed to
set up a separate sge for the page containing the READ data, and
another sge for XDR padding if needed, then post all of the sges via
a single SEND Work Request.
The problem is send_reply() does not advance through the xdr_buf
when setting up scatter/gather entries for SEND WR. It always calls
dma_map_xdr with xdr_off set to zero. When there's more than one
sge, dma_map_xdr() sets up the SEND sge's so they all point to the
xdr_buf's head.
The current Linux NFS/RDMA client always provides a reply chunk or
a write list when performing an NFS READ over RDMA. Therefore, it
does not exercise this particular case. The Linux server has never
had to use more than one extra sge for building RPC/RDMA replies
with a Linux client.
However, an NFS/RDMA client _is_ allowed to send small NFS READs
without setting up a write list or reply chunk. The NFS READ reply
fits entirely within the inline reply buffer in this case. This is
perhaps a more efficient way of performing NFS READs that the Linux
NFS/RDMA client may some day adopt.
Fixes: b432e6b3d9 ('svcrdma: Change DMA mapping logic to . . .')
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=285
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When removing underlying RDMA device, the rmmod will hang forever if there
are any outstanding NFS/RDMA client mounts. The outstanding NFS/RDMA counts
could also prevent the server from shutting down. Further debugging shows
that the existing connections are not teared down and resource are not
released when receiving RDMA_CM_EVENT_DEVICE_REMOVAL event. It seems the
original code missing svc_xprt_put() in RDMA_CM_EVENT_REMOVAL event handler
thus svc_xprt_free is never invoked to release the existing connection
resources.
The patch has been passed removing, adding device back and forth without
stopping NFS/RDMA service. This will also allow a device to be unplugged
and swapped out without shutting down NFS service.
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=252
Signed-off-by: Shirley Ma <shirley.ma@oracle.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Simon Horman says:
====================
IPVS Fixes for v4.2
please consider this fix for v4.2.
For reasons that are not clear to me it is a bumper crop.
It seems to me that they are all relevant to stable.
Please let me know if you need my help to get the fixes into stable.
* ipvs: fix ipv6 route unreach panic
This problem appears to be present since IPv6 support was added to
IPVS in v2.6.28.
* ipvs: skb_orphan in case of forwarding
This appears to resolve a problem resulting from a side effect of
41063e9dd1 ("ipv4: Early TCP socket demux.") which was included in v3.6.
* ipvs: do not use random local source address for tunnels
This appears to resolve a problem introduced by
026ace060d ("ipvs: optimize dst usage for real server") in v3.10.
* ipvs: fix crash if scheduler is changed
This appears to resolve a problem introduced by
ceec4c3816 ("ipvs: convert services to rcu") in v3.10.
Julian has provided backports of the fix:
* [PATCHv2 3.10.81] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04008.html
* [PATCHv2 3.12.44,3.14.45,3.18.16,4.0.6] ipvs: fix crash if scheduler is changed
http://www.spinics.net/lists/lvs-devel/msg04007.html
Please let me know how you would like to handle guiding these
backports into stable.
* ipvs: fix crash with sync protocol v0 and FTP
This appears to resolve a problem introduced by
749c42b620 ("ipvs: reduce sync rate with time thresholds") in v3.5
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Quoting Daniel Borkmann:
"When adding connection tracking template rules to a netns, f.e. to
configure netfilter zones, the kernel will endlessly busy-loop as soon
as we try to delete the given netns in case there's at least one
template present, which is problematic i.e. if there is such bravery that
the priviledged user inside the netns is assumed untrusted.
Minimal example:
ip netns add foo
ip netns exec foo iptables -t raw -A PREROUTING -d 1.2.3.4 -j CT --zone 1
ip netns del foo
What happens is that when nf_ct_iterate_cleanup() is being called from
nf_conntrack_cleanup_net_list() for a provided netns, we always end up
with a net->ct.count > 0 and thus jump back to i_see_dead_people. We
don't get a soft-lockup as we still have a schedule() point, but the
serving CPU spins on 100% from that point onwards.
Since templates are normally allocated with nf_conntrack_alloc(), we
also bump net->ct.count. The issue why they are not yet nf_ct_put() is
because the per netns .exit() handler from x_tables (which would eventually
invoke xt_CT's xt_ct_tg_destroy() that drops reference on info->ct) is
called in the dependency chain at a *later* point in time than the per
netns .exit() handler for the connection tracker.
This is clearly a chicken'n'egg problem: after the connection tracker
.exit() handler, we've teared down all the connection tracking
infrastructure already, so rightfully, xt_ct_tg_destroy() cannot be
invoked at a later point in time during the netns cleanup, as that would
lead to a use-after-free. At the same time, we cannot make x_tables depend
on the connection tracker module, so that the xt_ct_tg_destroy() would
be invoked earlier in the cleanup chain."
Daniel confirms this has to do with the order in which modules are loaded or
having compiled nf_conntrack as modules while x_tables built-in. So we have no
guarantees regarding the order in which netns callbacks are executed.
Fix this by allocating the templates through kmalloc() from the respective
SYNPROXY and CT targets, so they don't depend on the conntrack kmem cache.
Then, release then via nf_ct_tmpl_free() from destroy_conntrack(). This branch
is marked as unlikely since conntrack templates are rarely allocated and only
from the configuration plane path.
Note that templates are not kept in any list to avoid further dependencies with
nf_conntrack anymore, thus, the tmpl larval list is removed.
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
In the rare case that when it is a attempted to use a per network device
netfilter hook and the network device does not exist the newly allocated
structure can leak.
Be a good citizen and free the newly allocated structure in the error
handling code.
Fixes: 085db2c045 ("netfilter: Per network namespace netfilter hooks.")
Reported-by: kbuild@01.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of using peer link id for AID, generate a new
AID when creating mesh STAs in the kernel peering manager.
This enables smaller TIM elements and more closely follows
the standard, and it also enables mesh to work on drivers
that require a valid AID when the STA is inserted (ath10k
firmware has this requirement, for example).
In the case of userspace-managed stations, we use the AID
from NL80211_CMD_NEW_STATION.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to 802.11-2012 13.3.1, a mesh STA should assign an AID
upon receipt of a mesh peering open frame rather than using the link
id of the peer. Using the peer link id has two potential issues:
it may not be unique among the peers, and by its nature it is random,
so the TIM may not compress well.
In preparation for allocating it properly, use sta->sta.aid, but keep
the existing behavior of using the plid in the aid we send.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move mesh_plink_frame_tx() above the first caller to remove
the forward declaration.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 calls drv_resume() on wowlan resume,
but drops any incoming frame until local->suspended is
cleared later on.
This requires the low-level driver to support a new state,
in which it is expected to fully work (as it was resumed)
but not passing rx frames yet (as they will be dropped).
iwlwifi (and probably other drivers as well) has issues
supporting such mode.
Since in the wowlan case we already short-circuit
ieee80211_reconfig, there's nothing that prevents us from
clearing local->suspend before calling drv_resume(),
and letting the low-level driver work normally.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a TDLS station is not allowed to beacon on a channel, don't accept
a channel switch request to this channel.
Move channel building code up to avoid lockdep violations - reg_can_beacon
needs to take the wdev lock.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an SKB will be segmented by the driver, count it for multiple
MSDUs that are being transmitted rather than just a single.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit eeca9fce1d ('cfg80211: Schedule timeout for all CRDA calls')
left behind a superfluous check after it removed some earlier code.
In reg_process_hint, the test of "treatment == REG_REQ_IGNORE ||
treatment == REG_REQ_ALREADY_SET" is superfluous because the code in the
if-then branch is identical to the code after the if statement.
Coverity CID #1295939
I also removed the unnecessary assignment of treatment in this case,
and added a comment reminding any future patch authors to ensure that
treatment is properly assigned before it is used after the switch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This callback is currently not allowed to sleep, which makes it more
difficult to implement proper driver methods in mac80211 than it has
to be. Instead of doing asynchronous work here in mac80211, make it
possible for the callback to sleep by doing some asynchronous work
in cfg80211. This also enables improvements to other drivers, like
ath6kl, that would like to sleep in this callback.
While at it, also fix the code to call the driver on the implicit
unregistration when an interface is removed, and do that also when
a P2P-Device wdev is destroyed (otherwise we leak the structs.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most of the fields in this struct use too wide types, change
that to shrink the struct from 64 to 48 bytes (on 64-bit.)
This results in a total saving of 64 bytes for each interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch does the following:
- Remove unnecessary flags field used by PERR element
- Use the per target flags defined in <linux/ieee80211.h>
- Process the target only subfield based on case E2 of
IEEE802.11-2012 13.10.9.3
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already set a station to be associated when peering completes, both
in user space and in the kernel. Thus we should always have an
associated sta before sending data frames to that station.
Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized. This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.
Cc: stable@vger.kernel.org
Reported-by: Alexis Green <agreen@cococorp.com>
Tested-by: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When processing a PREQ or PREP it's critical to use the incoming SN. If
that is improperly done routing loops and other types of badness can
happen. But the code was always processing path messages for deactivated
paths. This path fixes that so that if we have a valid SN then we use it
to verify that it is a message we can accept. For reference the relevant
section of the standard is 13.10.8.4 which doesn't address the deactivated
path case at all.
I also included a special case for when our peer reboots or restarts
networking. This is an important case because without it there can be a
very long delay before we accept path messages from that peer. It's also a
simple case and intimately associated with processing messages for
deactivated paths so I used one patch instead of two.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 2012 spec mentions that path SNs can be invalid when created (see
section 13.10.8.4 table 13-9) but AFAICT never talks about invalidating
SNs. Which makes sense: if we have figured out the path to a target at a
certain SN then we want to remember that fact. Failing to do so can lead
to routing loops because if we don't have a valid SN then we have no way
of knowing whether an incoming path message leads to or away from the
target.
However currently when discovery fails we zero out mpath->flags which
clears MESH_PATH_SN_VALID. This patch fixes that so that only the
discovery relevant flags are cleared.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the nexthop is unable to resolve its own nexthop it will send back a
PERR with a zero target_sn. According to section 13.10.11.4.3 step b in the
2012 standard that perr should be forwarded and the associated mpath->sn
should be incremented. Neither one of those was happening which is rather
bad because the originator was not told that packets are black holing.
Signed-off-by: Alexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define a station chandef, to be used for wider-bw TDLS peers. When both
peers support the feature, upgrade the channel bandwidth to the maximum
allowed by both peers and regulatory. Currently widths up to 80MHz are
supported in the 5GHz band.
When a TDLS peer connects/disconnects recalculate the channel type of the
current chanctx.
Make the chanctx width calculation consider wider-bw TDLS peers and
similarly fix the max_required_bw calculation for the chanctx min_def.
Since the sta->bandwidth is calculated only later on, take
bss_conf.chandef.width as the minimal width for station interface.
Set the upgraded channel width in the VHT-operation set during TDLS setup.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.
Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If reconfiguration fails, local->in_reconfig is never
cleaned, resulting in rx frames being dropped next
time the device is started.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simply return NULL in this case, instead of crashing. This can
simplify callers that would otherwise have to check for this
explicitly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The beacon struct is already available in many contexts that
are also already in an RCU read-locked section. Avoid that by
using the existing beacon struct pointer directly.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
[rewrite subject/add commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code was always a bit awkward due to the 80-col restriction
and got worse in the previous patch. Refactor it a bit into its
own function to make it read nicer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a long-standing TODO item to use this flag in the cooked
monitor RX, but clearly it was never needed and now this hasn't
been used by userspace for a long time, so no userspace changes
could require it now.
Remove the unused flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the station hash table lookup (or iteration) must
access two cachelines for each station - the one with the hash
table node, and the one with the MAC address.
Duplicate the MAC address next to the hash node to get rid of
this. Since the MAC address is static there's no consistency
problem introduced by this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are multiple RX queues, the PN checks in mac80211 cannot be
used since packets might be processed out of order on different CPUs.
Allow the driver to report that the PN has been checked, drivers that
will use multi-queue RX will have to set this flag.
For now, the flag is only valid when the frame has been decrypted, in
theory that restriction doesn't have to be there, but in practice the
hardware will have decrypted the frame already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This counter is inherently racy (since it can be incremented by RX
as well as by concurrent TX) and only available in debugfs. Instead
of fixing it to be per-CPU or similar, remove it for now. If needed
it should be added without races and with proper nl80211, perhaps
even addressing the threshold reporting TODO item that's been there
since the code was originally added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
