NETIF_F_RXCSUM is not in the white list, though some
drivers may want to set it in order to enable seeing the
actual RX checksum status in ethtool.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few issues that were slowing down the process of finding
the optimal rate, especially on devices with multi-rate retry
limitations:
When max_tp_rate[0] was slower than max_tp_rate[1], the code did not
sample max_tp_rate[1], which would often allow it to switch places with
max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the
rate is otherwise good).
Also, sample attempts of rates between max_tp_rate[0] and [1] were being
ignored in this case, because the code only checked if the rate was
slower than [1].
Fix this by checking against the fastest / second fastest max_tp_rate
instead of assuming a specific order between the two.
In my tests this patch significantly reduces the time until minstrel_ht
finds the optimal rate right after assoc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we enqueued the frame that was supposed to be sent
during the SP, and that frame may very well cary the
IEEE80211_TX_STATUS_EOSP bit, we may never close the SP
(WLAN_STA_SP will never be cleared). If that happens, we
will not open any new SP and will never respond to any poll
frame from the client.
Clear WLAN_STA_SP manually if a frame that was polled during
the SP is queued because of a starting A-MPDU session. The
client may not see the EOSP bit, but it will at least be
able to poll new frames in another SP.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove erroneous comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible that the station is connected to an AP
with bandwidth of 80+80MHz or 160MHz. In such cases
there is no need to perform an upgrade as the maximal
supported bandwidth is 80MHz.
In addition, when upgrading and setting center_freq1
and bandwidth to 80MHz also set center_freq2 to 0.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible"
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Frames that are sent between
ampdu_action(IEEE80211_AMPDU_TX_START) and the move to the
HT_AGG_STATE_OPERATIONAL state are buffered.
If we try to start an A-MPDU session while the peer is
sleeping and polling frames with U-APSD, we may have frames
that will be buffered by ieee80211_tx_prep_agg. These frames
have IEEE80211_TX_CTL_NO_PS_BUFFER set since they are sent to
a sleeping client and possibly IEEE80211_TX_STATUS_EOSP.
If the frame is buffered, we need clear these two flags
since they will be re-sent after the move to
HT_AGG_STATE_OPERATIONAL state which is very likely to
happen after the SP ends.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 976bd9efda ("mac80211: move beacon_loss_count into ifmgd")
removed the member from the sta_info struct but the description stayed
lingering. Remove it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By default, the rhashtable logic will fail to insert
objects if the key-chains are too long and un-balanced.
In the degenerate case where mac80211 is creating many
virtual interfaces connected to the same peer(s), this
case can happen.
St insecure_elasticity to true to allow chains to grow
as long as needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[remove message, change commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The original hand-implemented hash-table in mac80211 couldn't result
in insertion errors, and while converting to rhashtable I evidently
forgot to check the errors.
This surfaced now only because Ben is adding many identical keys and
that resulted in hidden insertion errors.
Cc: stable@vger.kernel.org
Fixes: 7bedd0cfad ("mac80211: use rhashtable for station table")
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fall back to rate control if the requested bitrate was not found.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2
bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if
the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be
confused with IEEE80211_RADIOTAP_MCS_BW_20U.
Fixes: dfdfc2beb0 ("mac80211: Parse legacy and HT rate in injected frames")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introducing a new feature that the driver can use to
indicate the driver/firmware supports configuration of BSS
selection criteria upon CONNECT command. This can be useful
when multiple BSS-es are found belonging to the same ESS,
ie. Infra-BSS with same SSID. The criteria can then be used to
offload selection of a preferred BSS.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[move wiphy support check into parse_bss_select()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In certain cases, the 802.11 mesh pathtable code wants to
iterate over all of the entries in the forwarding table from
the receive path, which is inside an RCU read-side critical
section. Enable walks inside atomic sections by allowing
GFP_ATOMIC allocations for the walker state.
Change all existing callsites to pass in GFP_KERNEL.
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
[also adjust gfs2/glock.c and rhashtable tests]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path table uses a struct mesh_node in its hlists in
order to support a resizable hash table: the mesh_node provides
an indirection to the actual mesh path so that two different
bucket lists can point to the same path entry.
However, for the known gates list, we don't need this indirection
because there is ever only one list. So we can just embed the
hlist_node in the mesh path itself, which simplifies things a bit
and saves a linear search whenever we need to find an item in
the list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove duplicate code to allocate and initialize a mesh
path or mesh proxy path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the sdata pointer is the same for all entries of a
path table, hashing it is pointless, so hash only the address.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the cfg80211 scan trigger operation specifies a single BSSID, use
that value instead of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was requested by Android, and the appropriate cfg80211 API
had been added by Dmitry. Support it in mac80211, allowing drivers
to provide the timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using a switch to handle different ev.op values in rfkill_fop_write()
makes the code easier to extend, as out-of-range values can always be
handled by the default case.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
[roll in fix for RFKILL_OP_CHANGE from Jouni]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If register_netdevice_notifier() fails (which in practice it can't
right now), we should call unregister_pernet_subsys(). Do that.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Attackers like to use SYNFLOOD targeting one 5-tuple, as they
hit a single RX queue (and cpu) on the victim.
If they use random sequence numbers in their SYN, we detect
they do not match the expected window and send back an ACK.
This patch adds a rate limitation, so that the effect of such
attacks is limited to ingress only.
We roughly double our ability to absorb such attacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP uses per cpu 'sockets' to send some packets :
- RST packets ( tcp_v4_send_reset()) )
- ACK packets for SYN_RECV and TIMEWAIT sockets
By setting SOCK_USE_WRITE_QUEUE flag, we tell sock_wfree()
to not call sk_write_space() since these internal sockets
do not care.
This gives a small performance improvement, merely by allowing
cpu to properly predict the sock_wfree() conditional branch,
and avoiding one atomic operation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goal: packets dropped by a listener are accounted for.
This adds tcp_listendrop() helper, and clears sk_drops in sk_clone_lock()
so that children do not inherit their parent drop count.
Note that we no longer increment LINUX_MIB_LISTENDROPS counter when
sending a SYNCOOKIE, since the SYN packet generated a SYNACK.
We already have a separate LINUX_MIB_SYNCOOKIESSENT
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ss can report sk_drops, we can instruct TCP to increment
this per socket counter when it drops an incoming frame, to refine
monitoring and debugging.
Following patch takes care of listeners drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting sk_drops to user space was available for UDP
sockets using /proc interface.
Add this to sock_diag, so that we can have the same information
available to ss users, and we'll be able to add sk_drops
indications for TCP sockets as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a SYNFLOOD targets a non SO_REUSEPORT listener, multiple
cpus contend on sk->sk_refcnt and sk->sk_wmem_alloc changes.
By letting listeners use SOCK_RCU_FREE infrastructure,
we can relax TCP_LISTEN lookup rules and avoid touching sk_refcnt
Note that we still use SLAB_DESTROY_BY_RCU rules for other sockets,
only listeners are impacted by this change.
Peak performance under SYNFLOOD is increased by ~33% :
On my test machine, I could process 3.2 Mpps instead of 2.4 Mpps
Most consuming functions are now skb_set_owner_w() and sock_wfree()
contending on sk->sk_wmem_alloc when cooking SYNACK and freeing them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packet processing holds rcu_read_lock(), so we can remove
pairs of rcu_read_lock()/rcu_read_unlock() in lookup functions
if inet_diag also holds rcu before calling them.
This is needed anyway as __inet_lookup_listener() and
inet6_lookup_listener() will soon no longer increment
refcount on the found listener.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since linux 2.6.29, lookups only use rcu locking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert would like not touching UDP socket refcnt for encapsulated
traffic. For this to happen, we need to use normal RCU rules, with a grace
period before freeing a socket. UDP sockets are not short lived in the
high usage case, so the added cost of call_rcu() should not be a concern.
This actually removes a lot of complexity in UDP stack.
Multicast receives no longer need to hold a bucket spinlock.
Note that ip early demux still needs to take a reference on the socket.
Same remark for functions used by xt_socket and xt_PROXY netfilter modules,
but this might be changed later.
Performance for a single UDP socket receiving flood traffic from
many RX queues/cpus.
Simple udp_rx using simple recvfrom() loop :
438 kpps instead of 374 kpps : 17 % increase of the peak rate.
v2: Addressed Willem de Bruijn feedback in multicast handling
- keep early demux break in __udp4_lib_demux_lookup()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want a generic way to insert an RCU grace period before socket
freeing for cases where RCU_SLAB_DESTROY_BY_RCU is adding too
much overhead.
SLAB_DESTROY_BY_RCU strict rules force us to take a reference
on the socket sk_refcnt, and it is a performance problem for UDP
encapsulation, or TCP synflood behavior, as many CPUs might
attempt the atomic operations on a shared sk_refcnt
UDP sockets and TCP listeners can set SOCK_RCU_FREE so that their
lookup can use traditional RCU rules, without refcount changes.
They can set the flag only once hashed and visible by other cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Tested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the incorrect variable assignment on error path in
br_sysfs_addbr for when the call to kobject_create_and_add
fails to assign the value of -EINVAL to the returned variable of
err rather then incorrectly return zero making callers think this
function has succeededed due to the previous assignment being
assigned zero when assigning it the successful return value of
the call to sysfs_create_group which is zero.
Signed-off-by: Bastien Philbert <bastienphilbert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process socket-level control messages by invoking
__sock_cmsg_send in ip6_datagram_send_ctl for control messages on
the SOL_SOCKET layer.
This makes sure whenever ip6_datagram_send_ctl is called for
udp and raw, we also process socket-level control messages.
This is a bit uglier than IPv4, since IPv6 does not have
something like ipcm_cookie. Perhaps we can later create
a control message cookie for IPv6?
Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv6 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process socket-level control messages by invoking
__sock_cmsg_send in ip_cmsg_send for control messages on
the SOL_SOCKET layer.
This makes sure whenever ip_cmsg_send is called in udp, icmp,
and raw, we also process socket-level control messages.
Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv4 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept SO_TIMESTAMPING in control messages of the SOL_SOCKET level
as a basis to accept timestamping requests per write.
This implementation only accepts TX recording flags (i.e.,
SOF_TIMESTAMPING_TX_HARDWARE, SOF_TIMESTAMPING_TX_SOFTWARE,
SOF_TIMESTAMPING_TX_SCHED, and SOF_TIMESTAMPING_TX_ACK) in
control messages. Users need to set reporting flags (e.g.,
SOF_TIMESTAMPING_OPT_ID) per socket via socket options.
This commit adds a tsflags field in sockcm_cookie which is
set in __sock_cmsg_send. It only override the SOF_TIMESTAMPING_TX_*
bits in sockcm_cookie.tsflags allowing the control message
to override the recording behavior per write, yet maintaining
the value of other flags.
This patch implements validating the control message and setting
tsflags in struct sockcm_cookie. Next commits in this series will
actually implement timestamping per write for different protocols.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, to avoid a cache line miss for accessing skb_shinfo,
tcp_ack_tstamp skips socket that do not have
SOF_TIMESTAMPING_TX_ACK bit set in sk_tsflags. This is
implemented based on an implicit assumption that the
SOF_TIMESTAMPING_TX_ACK is set via socket options for the
duration that ACK timestamps are needed.
To implement per-write timestamps, this check should be
removed and replaced with a per-packet alternative that
quickly skips packets missing ACK timestamps marks without
a cache-line miss.
To enable per-packet marking without a cache line miss, use
one bit in TCP_SKB_CB to mark a whether a SKB might need a
ack tx timestamp or not. Further checks in tcp_ack_tstamp are not
modified and work as before.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_ID is set to get data-independent IDs
to associate timestamps with send calls. For TCP connections,
tp->snd_una is used as the starting point to calculate
relative IDs.
This socket option will fail if set before the handshake on a
passive TCP fast open connection with data in SYN or SYN/ACK,
since setsockopt requires the connection to be in the
ESTABLISHED state.
To address these, instead of limiting the option to the
ESTABLISHED state, accept the SOF_TIMESTAMPING_OPT_ID option as
long as the connection is not in LISTEN or CLOSE states.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To process cmsg's of the SOL_SOCKET level in addition to
cmsgs of another level, protocols can call sock_cmsg_send().
This causes a double walk on the cmsghdr list, one for SOL_SOCKET
and one for the other level.
Extract the inner demultiplex logic from the loop that walks the list,
to allow having this called directly from a walker in the protocol
specific code.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
