Coverity picked up that this looks like a cut-n-paste from an almost
identical sequence below that didn't get its variable renamed.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have USB gadgets disabled and USB_MUSB_HOST set, we get
errors "possible irq lock inverssion dependency detected"
errors during boot.
Let's fix the issue by adding start_musb flag and start
the controller after we're out of the spinlock protected
section.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
Fix one bug that host can't work after insmod gadget module
at dual-role mode, the root cause of this issue is the usbcmd.rs
is cleared by chipidea udc code.
Memory allocated for goku_udc device is not deallocated at error
paths in goku_probe(), because gadget_release() destructor
is not registered yet.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's perfectly fine to have all configfs functions
built-in while having modular legacy gadgets. Let's
allow for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Johan writes:
USB-serial fixes for v4.8-rc4
Here are a couple of fixes for non-atomic allocations in write paths,
and some new option device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Felipe writes:
usb: fixes for v4.8-rc3
Few fixes on dwc3 again, the most important being a
fix for pm_runtime to make it work with current
intel platforms.
Other than that, there's a signedness bug fix in fsl
udc and some other minor fixes.
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use gadget's framework allocation function instead of directly calling
usb_ep_alloc_request().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should always use free_ep_req() when allocating requests with
alloc_ep_req().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The default_length parameter of alloc_ep_req was not really necessary
and gadget drivers would almost always create an inline function to pass
the same value to len and default_len.
This patch removes that parameter and updates all calls to alloc_ep_req() to
use the new API.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TX settings can be calibrated for particular hardware. The
phy is reset by Linux, so this cannot be handled by the bootloader.
The TRM mentions that the maximum resistance should be used for the
DN/DP calibration in order to pass USB certification.
The values for the TX registers are poorly described in the TRM.
The meanings of the register values were taken from another
NXP-provided document:
https://community.nxp.com/message/566147#comment-566912
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_CONFIG0_SETUP.
When this flag is enabled, FunctionFS userspace drivers can process
non-standard control requests in configuration 0.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It can sometimes be necessary for gadget drivers to process non-standard
control requests, which host devices can send without having sent
USB_REQ_SET_CONFIGURATION.
Therefore, the req_match() usb_function method is enhanced with the new
parameter "config0". When a USB configuration is active, this parameter
is false. When a non-core control request is processed in
composite_setup(), without an active configuration, req_match() of the
USB functions of all available configurations which implement this
function, is called with config0=true. Then the control request gets
processed by the first usb_function instance whose req_match() returns
true.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
