In some rare cases we may get multiple interrupts that will generate
duplicate omap_musb_mailbox() calls. This is a problem because each
VBUS/ID event generates runtime_pm call in OMAP glue code, causing
unbalanced gets or puts and breaking PM.
The same goes for initial state, glue already defaults to "no cable"
state, so only bother it if we have VBUS or ID.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no need to do it, otg.set_suspend(false) (which itself
comes from runtime_pm OMAP glue calls) will enable it later anyway.
This used to be the place where things were enabled if booted with
cable connected before runtime_pm conversion, but now can be dropped.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Kconfig symbol USB_GADGET_NET2272_DMA was renamed to USB_NET2272_DMA
in commit 193ab2a607 ("usb: gadget: allow
multiple gadgets to be built"). That commit did not convert the only
occurrence of the corresponding Kconfig macro. Convert that macro now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 27b351c554.
Calling tty_flip_buffer_push on an unopened tty is legal, so the
driver doesn't need track if port has been opened. Reverting this
allows the entire is_open logic to be removed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the fixes in that branch, and let Alan fix the merge
error in drivers/usb/host/ehci-timer.c better than I just did (as I know
I messed it up...)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1670) fixes a regression caused by commit
6402c796d3 (USB: EHCI: work around
silicon bug in Intel's EHCI controllers). The workaround goes through
two IAA cycles for each QH being unlinked. During the first cycle,
the QH is not added to the async_iaa list (because it isn't fully gone
from the hardware yet), which means that list will be empty.
Unfortunately, I forgot to update the IAA watchdog timer routine. It
thinks that an empty async_iaa list means the timer expiration was an
error, which isn't true any more. This problem didn't show up during
initial testing because the controllers being tested all had working
IAA interrupts. But not all controllers do, and when the watchdog
timer expires, the empty-list check prevents the second IAA cycle from
starting. As a result, URB unlinks never complete. The check needs
to be removed.
Among the symptoms of the regression are processes stuck in D wait
states and hangs during system shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-by: Andreas Bombe <aeb@debian.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB_ULPI and USB_ULPI_VIEWPORT shouldn't really
be selected directly by anyone, but since Tegra
still needs some time before turning ulpi viewport
into a proper PHY driver, we need to keep the
selects in place.
This patch just fixes the conditional select
so that it will continue to build after merging
the latest PHY layer changes.
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The udc_irq service runs the isr_tr_complete_handler which in turn
"nukes" the endpoints, including a call to rndis_response_complete,
if appropriate. If the rndis_msg_parser fails here, an error will
be printed using a dev_err call (through the ERROR() macro).
However, if the usb cable was just disconnected the device (cdev)
might not be available and will be null. Since the dev_err macro will
dereference the cdev pointer we get a null pointer exception.
Reviewed-by: Radovan Lekanovic <radovan.lekanovic@sonymobile.com>
Signed-off-by: Truls Bengtsson <truls.bengtsson@sonymobile.com>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an "off-by-one" bug found in
581791f (FunctionFS: enable multiple functions).
During gfs_bind/gfs_unbind the functionfs_bind/functionfs_unbind should be
called for every functionfs instance. With the "i" pre-decremented they
were not called for the zeroth instance.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@vger.kernel.org>
[ balbi@ti.com : added offending commit's subject ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1667) removes an incorrect driver->unbind() call from
the net2280 driver. If startup fails, the UDC core takes care of
unbinding the gadget driver automatically; the controller driver
shouldn't do it too.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1666) fixes a regression in the UDC core. The core
takes care of unbinding gadget drivers, and it does the unbinding
before telling the UDC driver to turn off the controller hardware.
When the call to the udc_stop callback is made, the gadget no longer
has a driver. The callback routine should not be invoked with a
pointer to the old driver; doing so can cause problems (such as
use-after-free accesses in net2280).
This patch should be applied, with appropriate context changes, to all
the stable kernels going back to 3.1.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
with the latest udc_start/udc_stop conversion,
too much code was deleted which ended up creating
a regression in net2272 and net2280 drivers.
To fix the regression we revert one hunk of the
original commits.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to recent changes to regulator API, all
users which don't check regulator_{en,dis}able()'s
return value will generate compile warnings.
Add such checks to gpio-vbus.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->ops->break_ctl cannot be called outside the gap between open and
close. So there is no need to check whether the port is open in
break_ctl in quatech2. Remove the check and also that member
completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci_vbus_gpio is requested but never freed. This can cause
problems with deferred probes and would cause problems if
s5p_ehci_remove was ever called. Use devm to fix this.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1637) cleans up the way ehci-hcd handles end-of-resume
port signalling. When the PORT_RESUME bit in the port's status and
control register is cleared, we shouldn't be setting the PORT_SUSPEND
bit at the same time. Not doing this doesn't seem to have hurt so
far, but we might as well do the right thing.
Also, the patch replaces an estimated value for what the port status
should be following a resume with the actual register value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1635) rearranges the control-flow logic in
ehci_iaa_watchdog() slightly to agree better with the comments. It
also changes a verbose-debug message to a regular debug message.
Expiration of the IAA watchdog is an unusual event and can lead to
problems; we need to know about it if it happens during debugging. It
should not be necessary to set a "verbose" compilation option.
No behavioral changes other than the debug message. Lots of apparent
changes to the source text, though, because the indentation level was
decreased.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1634) simplifies some of the code associated with the
per-port change bits added in EHCI-1.1, and in particular it fixes a
bug in the logic of ehci_hub_status_data(). Even if the change bit
doesn't indicate anything happened on a particular port, we still have
to notify the core about changes to the suspend or reset status.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1657) decreases the timeout used by ehci-hcd for polling
the async and periodic schedule statuses. The timeout is currently
set to 20 ms, which is much too high. Controllers should always
update the schedule status within one or two ms of being told to do
so; if they don't then something is wrong.
Furthermore, bug reports have shown that sometimes controllers
(particularly those made by VIA) don't update the status bit at all,
even when the schedule does change state. When this happens, polling
for 20 ms would cause an unnecessarily long delay.
The delay is reduced to somewhere between 2 and 4 ms, depending on the
slop allowed by the kernel's high-res timers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.
Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.
This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87 "xhci: don't
re-enable IE constantly".
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver. The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.
This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AB8500 versions preceding 2.0 were only used internally by ST-Ericsson
and are not supported anymore. This patch drops all v1.0 and v1.1
support code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add transceiver notifier event handling to the ux500 driver to set vbus
on specific transceiver events.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
[ balbi@ti.com: fix build error due to missing
otg_state_string() ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add ux500_musb_set_vbus() implementation for ux500.
This is based on the version originally developed inside ST-Ericsson.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
[ balbi@ti.com: fix a build error due to
missing otg_state_string() ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: Felipe Balbi <balbi@ti.com>
PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: Felipe Balbi <balbi@ti.com>
PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Having twl4030_usb_phy_init() (detects if a cable is connected before
twl4030 is probed) in twl4030 probe makes cable connect events to be
missed by musb glue, since it gets loaded after twl4030. Having
twl4030_usb_phy_init as a usb_phy ops lets twl4030_usb_phy_init to be
called when glue is ready.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Used devres APIs devm_request_threaded_irq and devm_regulator_get for
requesting irq and for getting regulator respectively.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some PHYs load too early (twl4030) making omap glue to miss cable connect events
if the board is booted with cable connected. So adding usb_phy_init in
omap2430_musb_init lets PHYs to report events once glue is ready.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. otg_set_vbus is already protected so removed the
check before calling otg_set_vbus.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
our global '_omap' pointer wasn't marked
static. This patch solves the following sparse
warning:
warning: symbol '_omap' was not declared. \
Should it be static?
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional change. Replace *_* with *-* in property names of otg to
follow the general convention.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per the USB3.0 specs, the bandwidth requirements of a UVC's video
streaming endpoint will change to support super-speed. These changes
will be dependent on whether the UVC video streaming endpoint is Bulk or
Isochronous:
- If video streaming endpoint is Isochronous:
As per Section 4.4.8.2 (Isochronous Transfer Bandwidth Requirements)
of the USB3.0 specs:
A SuperSpeed isochronous endpoint can move up to three burst
transactions of up to 16 maximum sized packets (3 * 16 * 1024 bytes)
per service interval.
- If video streaming endpoint is Bulk:
As per 4.4.6.1 (Bulk Transfer Data Packet Size) of the USB3.0 specs:
An endpoint for bulk transfers shall set the maximum data packet
payload size in its endpoint descriptor to 1024 bytes. It also
specifies the burst size that the endpoint can accept from or
transmit on the SuperSpeed bus. The allowable burst size for a bulk
endpoint shall be in the range of 1 to 16.
So, in the Isochronous case, we can define the USB request's buffer to
be equal to = (Maximum packet size) * (bMaxBurst + 1) * (Mult + 1), so
that the UDC driver can try to send out this buffer in one Isochronous
service interval.
The same computation will hold good for the Bulk case as the Mult
value is 0 here and we can have a USB request buffer of maximum
16 * 1024 bytes size, which can be sent out by the UDC driver as
per the Bulk bandwidth allocation on the USB3 bus.
This patch adds the above-mentioned support and is also USB2.0 backward
compliant.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds the support in UVC webcam gadget design for providing
USB_GADGET_DELAYED_STATUS in response to a set_interface(alt setting 1)
command issue by the Host.
The current UVC webcam gadget design generates a STREAMON event
corresponding to a set_interface(alt setting 1) command from the Host.
This STREAMON event will eventually be routed to a real V4L2 device.
To start video streaming, it may be required to perform some register
writes to a camera sensor device over slow external busses like I2C or
SPI. So, it makes sense to ensure that we delay the STATUS stage of the
set_interface (alt setting 1) command.
Otherwise, a lot of ISOC IN tokens sent by the Host will be replied to
by zero-length packets by the webcam device. On certain Hosts this may
even lead to ISOC URBs been cancelled from the Host side.
So, as soon as we finish doing all the "streaming" related stuff on the
real V4L2 device, we call a STREAMON ioctl on the UVC side and from here
we call the 'usb_composite_setup_continue' function to complete the
status stage of the set_interface(alt setting 1) command.
Further, we need to ensure that we queue no video buffers on the UVC
webcam gadget, until we de-queue a video buffer from the V4L2 device.
So, the application should call the STREAMON on UVC side only when it
has dequeued sufficient buffers from the V4L2 side and queued them to
the UVC gadget.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As per the UVC compliance test suite's assertion 6.1.25, the `iFunction`
field of the Interface Association Descriptor (IAD) should the match the
`iInterface` field of the standard Video Control (VC) Interface Descriptor for
this Video Interface Collection (VIC).
This mandatory case is captured in section 3.11 of the
USB Video Class Compliance specification revision 1.1
This patch fixes this test assertion's failure and has been tested on
Linux FC16, WinXP, WIN7 and WIN8 High speed and Super Speed hosts
for successful enumeration.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
[Merged the association and control string descriptors]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
