cp210x_get_config and cp210x_set_config are cumbersome to use. This change
introduces new register access functions for 16-bit values, instead of
the above functions.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Bool initializations should use true and false. Bool tests don't need
comparisons.
Also, use IS_ENABLED instead of ifdef.
Generated by: scripts/coccinelle/misc/boolinit.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unneeded variables when "0" can be returned.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move constants to the right of binary operators where it increases
readability.
Generated by: scripts/coccinelle/misc/compare_const_fl.cocci
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: drop some chunks and fix others, amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The check for < 0 is impossible now that
of_clk_get_parent_count() returns an unsigned int. Simplify the
code and update the types.
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
From Alexandre Belloni:
"This is a rework of the PMC driver. It touches multiple subsystems so
the easiest path is through arm-soc."
drivers update for 4.6:
- Big PMC rework that touches clk, PM, usb
* tag 'at91-ab-4.6-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
Signed-off-by: Olof Johansson <olof@lixom.net>
Felipe writes:
usb: fixes for v4.5-rc6
The most important fixes here are:
a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;
b) two DMA fixes for the old MUSB driver.
c) dwc2's data toggle fix for FS
Other than these, we have a few other minor fixes
elsewhere.
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some platforms don't have DMA, but we should still be able to build USB
drivers for these platforms. They could still be used through vhci_hcd,
usbip_host, or maybe something like USB passthrough in UML from a
capable host.
If NO_DMA=y:
ERROR: "dma_pool_destroy" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "bad_dma_ops" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_free" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_alloc" [drivers/usb/core/usbcore.ko] undefined!
ERROR: "dma_pool_create" [drivers/usb/core/usbcore.ko] undefined!
Add a few checks for CONFIG_HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The US_DEBUGPX macro uses printk without specifying a kernel log level, so
the default kernel log level is used, which may not match LOGLEVEL_DEBUG
used in usb_stor_dbg. Remove the macro and use usb_store_dbg instead.
Signed-off-by: Victor Dodon <printesoi@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device is disconnected poll waiters were not being woken.
Changes for v2:
- add commit summary
- add Fixes and Reported-by tags
Fixes: eb6b92ecc0 ("Add support for receiving USBTMC USB488 SRQ notifications via poll/select")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write value is 8bit, but currently writing a larger number (eg a doubled
digit) is not errored but instead gets cast and sets off an action probably
undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shares the cleanup code between all probe failure paths, instead of
having per-failure cleanup at each point in the function.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d8f00cd685.
Tony writes:
This upstream commit is causing an oops:
d8f00cd685 ("usb: hub: do not clear BOS field during reset device")
This patch has already been included in several -stable kernels. Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61
How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: Tony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
