This driver adds support for the PCIe 2.0 controller found on the BCMA bus.
This controller can be found on (mostly) all Broadcom BCM470X / BCM5301X
ARM SoCs.
The driver found in the Broadcom SDK does some more stuff, like setting up
some DMA memory areas, chaining MPS and MRRS to 512 and also some PHY
changes like "improving" the PCIe jitter and doing some special
initialization for the 3rd PCIe port.
This was tested on a bcm4708 board with 2 PCIe ports and wireless cards
connected to them.
PCI_DOMAINS is needed by this driver, because normally there is more than
one PCIe controller and without PCI_DOMAINS only the first controller gets
registered. This controller gets 6 IRQs; the last one is trigged by all
IRQ events.
[bhelgaas: fix "GPLv2" MODULE_LICENSE typo]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Ray Jui <rjui@broadcom.com.com>
The ACPI 6 specification has made some changes in the device power
management area. In particular:
* The D3hot power state is now supposed to be always available
(instead of D3cold) and D3cold is only regarded as valid if the
_PR3 object is present for the given device.
* The required ordering of transitions into power states deeper than
D0 is now such that for a transition into state Dx the _PSx method
is supposed to be executed first, if present, and the states of
the power resources the device depends on are supposed to be
changed after that.
* It is now explicitly forbidden to transition devices from
lower-power (deeper) into higher-power (shallower) power states
other than D0.
Those changes have been made so the specification reflects the
Windows' device power management code that the vast majority of
systems using ACPI is validated against.
To avoid artificial differences in ACPI device power management
between Windows and Linux, modify the ACPI device power management
code to follow the new specification. Add comments explaining the
code flow in some unclear places.
This only may affect some real corner cases in which the OS behavior
expected by the firmware is different from the Windows one, but that's
quite unlikely. The transition ordering change affects transitions
to D1 and D2 which are rarely used (if at all) and into D3hot and
D3cold for devices actually having _PR3, but those are likely to
be validated against Windows anyway. The other changes may affect
code calling acpi_device_get_power() or acpi_device_update_power()
where ACPI_STATE_D3_HOT may be returned instead of ACPI_STATE_D3_COLD
(that's why the ACPI fan driver needs to be updated too) and since
transitions into ACPI_STATE_D3_HOT may remove power now, it is better
to avoid this one in acpi_pm_device_sleep_state() if the "no power
off" PM QoS flag is set.
The only existing user of acpi_device_can_poweroff() really cares
about the case when _PR3 is present, so the change in that function
should not cause any problems to happen too.
A plus is that PCI_D3hot can be mapped to ACPI_STATE_D3_HOT
now and the compatibility with older systems should be covered
automatically.
In any case, if any real problems result from this, it still will
be better to follow the Windows' behavior (which now is reflected
by the specification too) in general and handle the cases when it
doesn't work via quirks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Intel confirms that 9-series chipset root ports provide ACS-equivalent
isolation when configured via the existing Intel PCH ACS quirk setup.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI. Remove device-specific code to disable
MSI/MSI-X.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If we enable MSI, then kexec a new kernel, the new kernel may receive MSIs
it is not prepared for. Commit d5dea7d95c ("PCI: msi: Disable msi
interrupts when we initialize a pci device") prevents this, but only if the
new kernel is built with CONFIG_PCI_MSI=y.
Move the "disable MSI" functionality from drivers/pci/msi.c to a new
pci_msi_setup_pci_dev() in drivers/pci/probe.c so we can disable MSIs when
we enumerate devices even if the kernel doesn't include full MSI support.
[bhelgaas: changelog, disable MSIs in pci_setup_device(), put
pci_msi_setup_pci_dev() at its final destination]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_msi_set_enable() and pci_msix_clear_and_set_ctrl() to
drivers/pci/pci.h so they're available even when MSI isn't configured
into the kernel.
No functional change.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Rename msi_set_enable() to pci_msi_set_enable() and
msix_clear_and_set_ctrl() to pci_msix_clear_and_set_ctrl().
No functional change.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Pull xen features and fixes from David Vrabel:
- use a single source list of hypercalls, generating other tables etc.
at build time.
- add a "Xen PV" APIC driver to support >255 VCPUs in PV guests.
- significant performance improve to guest save/restore/migration.
- scsiback/front save/restore support.
- infrastructure for multi-page xenbus rings.
- misc fixes.
* tag 'stable/for-linus-4.1-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pci: Try harder to get PXM information for Xen
xenbus_client: Extend interface to support multi-page ring
xen-pciback: also support disabling of bus-mastering and memory-write-invalidate
xen: support suspend/resume in pvscsi frontend
xen: scsiback: add LUN of restored domain
xen-scsiback: define a pr_fmt macro with xen-pvscsi
xen/mce: fix up xen_late_init_mcelog() error handling
xen/privcmd: improve performance of MMAPBATCH_V2
xen: unify foreign GFN map/unmap for auto-xlated physmap guests
x86/xen/apic: WARN with details.
x86/xen: Provide a "Xen PV" APIC driver to support >255 VCPUs
xen/pciback: Don't print scary messages when unsupported by hypervisor.
xen: use generated hypercall symbols in arch/x86/xen/xen-head.S
xen: use generated hypervisor symbols in arch/x86/xen/trace.c
xen: synchronize include/xen/interface/xen.h with xen
xen: build infrastructure for generating hypercall depending symbols
xen: balloon: Use static attribute groups for sysfs entries
xen: pcpu: Use static attribute groups for sysfs entry
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Originally Xen PV drivers only use single-page ring to pass along
information. This might limit the throughput between frontend and
backend.
The patch extends Xenbus driver to support multi-page ring, which in
general should improve throughput if ring is the bottleneck. Changes to
various frontend / backend to adapt to the new interface are also
included.
Affected Xen drivers:
* blkfront/back
* netfront/back
* pcifront/back
* scsifront/back
* vtpmfront
The interface is documented, as before, in xenbus_client.c.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.
Some minor conflicts with Daniel's pci_controller_ops work.
Conflicts:
arch/powerpc/include/asm/machdep.h
arch/powerpc/platforms/powernv/pci-ioda.c
* pci/misc:
PCI: Read capability list as dwords, not bytes
PCI: Don't clear ASPM bits when the FADT declares it's unsupported
PCI: Clarify policy for vendor IDs in pci.txt
PCI/ACPI: Optimize device state transition delays
PCI: Export pci_find_host_bridge() for use inside PCI core
PCI: Make a shareable UUID for PCI firmware ACPI _DSM
PCI: Fix typo in Thunderbolt kernel message
Reading both the capability ID and "next" pointer at the same time lets us
parse the list with half the number of config reads.
Signed-off-by: Sean O. Stalley <sean.stalley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check for failure from platform_get_resource() (this check actually happens
inside devm_ioremap_resource()) before dereferencing the pointer returned
from platform_get_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check for failure of devm_ioremap_resource().
devm_ioremap_resource() validates the resource it receives, so if we check
for devm_ioremap_resource() failure, we need not check for failure of the
preceding platform_get_resource().
[bhelgaas: changelog]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Communications with a hardware vendor confirm that the expected behaviour
on systems that set the FADT ASPM disable bit but which still grant full
PCIe control is for the OS to leave any BIOS configuration intact and
refuse to touch the ASPM bits. This mimics the behaviour of Windows.
Signed-off-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull PCI fixes from Bjorn Helgaas:
"Here are some fixes for v4.0. I apologize for how late they are. We
were hoping for some better fixes, but couldn't get them polished in
time. These fix:
- a Xen domU oops with PCI passthrough devices
- a sparc T5 boot failure
- a STM SPEAr13xx crash (use after initdata freed)
- a cpcihp hotplug driver thinko
- an AER thinko that printed stack junk
Details:
Enumeration
- Don't look for ACPI hotplug parameters if ACPI is disabled (Bjorn Helgaas)
Resource management
- Revert "sparc/PCI: Clip bridge windows to fit in upstream windows" (Bjorn Helgaas)
AER
- Avoid info leak in __print_tlp_header() (Rasmus Villemoes)
PCI device hotplug
- Add missing curly braces in cpci_configure_slot() (Dan Carpenter)
ST Microelectronics SPEAr13xx host bridge driver
- Drop __initdata from spear13xx_pcie_driver (Matwey V. Kornilov)
* tag 'pci-v4.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "sparc/PCI: Clip bridge windows to fit in upstream windows"
PCI: Don't look for ACPI hotplug parameters if ACPI is disabled
PCI: cpcihp: Add missing curly braces in cpci_configure_slot()
PCI/AER: Avoid info leak in __print_tlp_header()
PCI: spear: Drop __initdata from spear13xx_pcie_driver
The PCI "ACPI additions for FW latency optimizations" ECN (link below)
defines two functions in the PCI _DSM:
Function 8, "Reset Delay," applies to the entire hierarchy below a PCI
host bridge. If it returns one, the OS may assume that all devices in
the hierarchy have already completed power-on reset delays.
Function 9, "Device Readiness Durations," applies only to the object
where it is located. It returns delay durations required after various
events if the device requires less time than the spec requires. Delays
from this function take precedence over the Reset Delay function.
Add support for Reset Delay and part of Device Readiness Durations.
[bhelgaas: changelog, comments]
Link: https://www.pcisig.com/specifications/conventional/pci_firmware/ECN_fw_latency_optimization_final.pdf
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The find_pci_host_bridge() function can be useful to other PCI code so
export it. Change its name to pci_find_host_bridge().
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI Firmware Specification, r3.0, sec 4.6.4.1.3, defines a single UUID
for an ACPI _DSM method to provide device-specific control functions. This
_DSM method support several functions, including PCI Express Slot
Information, PCI Express Slot Number, PCI Bus Capabilities, etc.
Move the UUID definition from pci/pci-label.c, where it could be used only
for one function, to pci/pci-acpi.c where it can be shared for all these
functions.
[bhelgaas: changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for the Broadcom iProc PCIe controller.
pcie-iproc.c is the common core driver, and a front-end bus interface needs
to be added to support different bus interfaces.
pcie-iproc-platform.c contains the support for the platform bus interface.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Export the following symbols so they can be referenced by a PCI host bridge
driver compiled as a kernel loadable module:
pci_common_swizzle
pci_create_root_bus
pci_stop_root_bus
pci_remove_root_bus
pci_assign_unassigned_bus_resources
pci_fixup_irqs
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Booting a v3.18 or newer Xen domU kernel with PCI devices passed through
results in an oops (this is a 32-bit 3.13.11 dom0 with a 64-bit 4.4.0
hypervisor and 32-bit domU):
BUG: unable to handle kernel paging request at 0030303e
IP: [<c06ed0e6>] acpi_ns_validate_handle+0x12/0x1a
Call Trace:
[<c06eda4d>] ? acpi_evaluate_object+0x31/0x1fc
[<c06b78e1>] ? pci_get_hp_params+0x111/0x4e0
[<c0407bc7>] ? xen_force_evtchn_callback+0x17/0x30
[<c04085fb>] ? xen_restore_fl_direct_reloc+0x4/0x4
[<c0699d34>] ? pci_device_add+0x24/0x450
Don't look for ACPI configuration information if ACPI has been disabled.
I don't think this is the best fix, because we can boot plain Linux (no
Xen) with "acpi=off", and we don't need this check in pci_get_hp_params().
There should be a better fix that would make Xen domU work the same way.
The domU kernel has ACPI support but it has no AML. There should be a way
to initialize the ACPI data structures so things fail gracefully rather
than oopsing. This is an interim fix to address the regression.
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96301
Reported-by: Michael D Labriola <mlabriol@gdeb.com>
Tested-by: Michael D Labriola <mlabriol@gdeb.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.18+
When sizing and assigning resources, we divide the resources into two
lists: the requested list and the additional list. We don't consider the
alignment of additional VF(n) BAR space.
This is because the alignment required for the VF(n) BAR space is the size
of an individual VF BAR, not the size of the space for *all* VFs. But we
want additional alignment to support partitioning on PowerNV.
Consider the additional IOV BAR alignment when sizing and assigning
resources. When there is not enough system MMIO space to accomodate both
the requested list and the additional list, the PF's IOV BAR alignment will
not contribute to the bridge. When there is enough system MMIO space for
both lists, the additional alignment will contribute to the bridge.
The additional alignment is stored in the min_align of pci_dev_resource,
which is stored in the additional list by add_to_list() at the end of
pbus_size_mem(). The additional alignment is calculated in
pci_resource_alignment(). For an IOV BAR, we have arch dependent function
to get the alignment for different arch.
[bhelgaas: changelog, printk cast]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Per the SR-IOV spec r1.1, sec 3.3.14, the required alignment of a PF's IOV
BAR is the size of an individual VF BAR, and the size consumed is the
individual VF BAR size times NumVFs.
The PowerNV platform has additional alignment requirements to help support
its Partitionable Endpoint device isolation feature (see
Documentation/powerpc/pci_iov_resource_on_powernv.txt).
Add a pcibios_iov_resource_alignment() interface to allow platforms to
request additional alignment.
[bhelgaas: changelog, adapt to reworked pci_sriov_resource_alignment(),
drop "align" parameter]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
VFs are dynamically created when a driver enables them. On some platforms,
like PowerNV, special resources are necessary to enable VFs.
Add platform hooks for enabling and disabling VFs.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV, some resource reservation is needed for SR-IOV VFs that don't
exist at the bootup stage. To do the match between resources and VFs, the
code need to get the VF's BDF in advance.
Rename virtfn_bus() and virtfn_devfn() to pci_iov_virtfn_bus() and
pci_iov_virtfn_devfn() and export them.
[bhelgaas: changelog, make "busnr" int]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An SR-IOV device can change its First VF Offset and VF Stride based on the
values of ARI Capable Hierarchy and NumVFs. The number of buses required
for all VFs is determined by NumVFs, First VF Offset, and VF Stride (see
SR-IOV spec r1.1, sec 2.1.2).
Previously pci_iov_bus_range() computed how many buses would be required by
TotalVFs, but this was based on a single NumVFs value and may not have been
the maximum for all NumVFs configurations.
Iterate over all valid NumVFs and calculate the maximum number of bus
numbers that could ever be required for VFs of this device.
[bhelgaas: changelog, compute busnr of NumVFs, not TotalVFs, remove
kerenl-doc comment marker]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The First VF Offset and VF Stride fields depend on the NumVFs setting, so
refresh the cached fields in struct pci_sriov when updating NumVFs. See
the SR-IOV spec r1.1, sec 3.3.9 and 3.3.10.
[bhelgaas: changelog, remove kernel-doc comment marker]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Most of PCI uses "res = &dev->resource[i]", not "res = dev->resource + i".
Use that style in iov.c also.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we don't store the individual VF BAR size. We calculate it when
needed by dividing the PF's IOV resource size (which contains space for
*all* the VFs) by total_VFs or by reading the BAR in the SR-IOV capability
again.
Keep the individual VF BAR size in struct pci_sriov.barsz[], add
pci_iov_resource_size() to retrieve it, and use that instead of doing the
division or reading the SR-IOV capability BAR.
[bhelgaas: rename to "barsz[]", simplify barsz[] index computation, remove
SR-IOV capability BAR sizing]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we size VF BAR0, VF BAR1, etc., from the SR-IOV Capability of a PF, we
learn the alignment requirement and amount of space consumed by a single
VF. But when VFs are enabled, *each* of the NumVFs consumes that amount of
space, so the total size of the PF resource is "VF BAR size * NumVFs".
Add a printk of the total space consumed by the VFs corresponding to what
we already do for normal non-IOV BARs.
No functional change; new message only.
[bhelgaas: split out into its own patch]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we don't have space for all the bus numbers required to enable VFs,
print the largest bus number required and the range available.
No functional change; improved error message only.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH core probes on device_node or pci_dev to populate
EEH devices and PEs, which conflicts with the fact: SRIOV VFs are
usually enabled and created by PF's driver and they don't have the
corresponding device_nodes. Instead, SRIOV VFs have dynamically
created pci_dn, which can be used for EEH probe.
The patch reworks EEH probe for PowerNV and pSeries platforms to
do probing based on pci_dn, instead of pci_dev or device_node any
more.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Intel has verified that there is no peer-to-peer between functions for the
below selection of 82580, 82576, 82575, I350, and 82571 multi-port devices.
This adds the necessary quirks to consider the functions isolated from each
other. 82571 quad-port devices are omitted due to likely lack of
ACS/isolation in the onboard switch, rendering quirks for the downstream
endpoints useless.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
Add suspend/resume support for the mvebu PCIe host driver. Without this
commit, the system will panic at resume time when PCIe devices are
connected.
Note that we have to use the ->suspend_noirq() and ->resume_noirq() hooks,
because at resume time, the PCI fixups are done at ->resume_noirq() time,
so the PCIe controller has to be ready at this point.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
* pci/iommu:
of: Calculate device DMA masks based on DT dma-range size
arm: dma-mapping: limit IOMMU mapping size
PCI: Update DMA configuration from DT
of/pci: Add of_pci_dma_configure() to update DMA configuration
PCI: Add helper functions pci_get[put]_host_bridge_device()
of: Fix size when dma-range is not used
of: Move of_dma_configure() to device.c to help re-use
of: iommu: Add ptr to OF node arg to of_iommu_configure()
* pci/resource:
PCI: Fail pci_ioremap_bar() on unassigned resources
PCI: Show driver, BAR#, and resource on pci_ioremap_bar() failure
PCI: Mark invalid BARs as unassigned
PNP: Don't check for overlaps with unassigned PCI BARs
