Split the PCIe port DT parsing and resource claiming from setting up the
actual ports. This allows us to gather all the resources first, before
touching the hardware. This is important as some of these resources (such
as the GPIO for the PCIe reset) may defer probing.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvebu PCI port parsing is weak due to:
1) allocations via kasprintf() were not cleaned up when we encounter an
error or decide to skip the port.
2) kasprintf() wasn't checked for failure.
3) of_get_named_gpio_flags() returns EPROBE_DEFER if the GPIO is not
present, not devm_gpio_request_one().
4) the of_node was not being put when terminating the loop.
Fix these oversights.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The idea that you can arbitarily read 32-bits from PCI configuration space,
modify a sub-field (like the command register) and write it back without
consequence is deeply flawed.
Status registers (such as the status register, PCIe device status register,
etc) contain status bits which are read, write-one-to-clear.
What this means is that reading 32-bits from the command register,
modifying the command register, and then writing it back has the effect of
clearing any status bits that were indicating at that time. Same for the
PCIe device control register clearing bits in the PCIe device status
register.
Since the Armada chips support byte, 16-bit and 32-bit accesses to the
registers (unless otherwise stated) and the PCI configuration data register
does not specify otherwise, it seems logical that the chip can indeed
generate the proper configuration access cycles down to byte level.
Testing with an ASM1062 PCIe to SATA mini-PCIe card on Armada 388. PCIe
capability at 0x80, DevCtl at 0x88, DevSta at 0x8a.
Before:
/# setpci -s 1:0.0 0x88.l - DevSta: CorrErr+
00012810
/# setpci -s 1:0.0 0x88.w=0x2810 - Write DevCtl only
/# setpci -s 1:0.0 0x88.l - CorrErr cleared - FAIL
00002810
After:
/# setpci -s 1:0.0 0x88.l - DevSta: CorrErr+
00012810
/# setpci -s 1:0.0 0x88.w=0x2810 - check DevCtl only write
/# setpci -s 1:0.0 0x88.l - CorErr remains set
00012810
/# setpci -s 1:0.0 0x88.w=0x281f - check DevCtl write works
/# setpci -s 1:0.0 0x88.l - devctl field updated
0001281f
/# setpci -s 1:0.0 0x8a.w=0xffff - clear DevSta
/# setpci -s 1:0.0 0x88.l - CorrErr now cleared
0000281f
/# setpci -s 1:0.0 0x88.w=0x2810 - restore DevCtl
/# setpci -s 1:0.0 0x88.l - check
00002810
[bhelgaas: changelog]
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
PCI requires reads to reserved or unimplemented configuration space to
return zero and complete normally (see PCI r3.0, sec 6.1). However, the
root port software implementation was returning 0xfffffff and
PCIBIOS_BAD_REGISTER_NUMBER.
Return zero when reading reserved or unimplemented config space.
[bhelgaas: changelog]
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If the bus is being configured with a bus-range that does not start at
zero, pass that starting bus number to pci_scan_root_bus(). Passing the
incorrect value of zero causes attempted config accesses outside of the
supported range, which cascades to an OOPs spew and eventual kernel panic.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The generic driver kept a global struct pci_ops ("gen_pci_ops") which it
patched with the .map_bus() method appropriate for the bus device. This is
a problem when we have two different types of bus devices: the .map_bus()
method for the last device probed clobbers the method for previous devices.
The result is that only the last bus device probed has the correct
.map_bus(), and the others fail.
Move the struct pci_ops into the bus-specific structure and initialize a
pointer to it when the bus device is probed.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
63692df103 ("PCI: Allow numa_node override via sysfs") didn't check that
the numa node provided by userspace is valid. Passing a node number too
high would attempt to access invalid memory and trigger a kernel panic.
Fixes: 63692df103 ("PCI: Allow numa_node override via sysfs")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.19+
After 8d63bc7bea ("PCI/MSI: pci-xgene-msi: Get rid of struct
msi_controller"), it is no longer required to assign msi_controller for
X-Gene PCIe host bridge to support MSI.
Remove this unnecessary code. This also avoids a warning message ("failed
to enable MSI") during boot.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Improve the link detection logic by explicitly querying the link status
register to ensure link is active.
Also force class to PCI_CLASS_BRIDGE_PCI (0x0604) through the host
configuration space register.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
The current reset logic does not always properly reset the device. For
example, in the case when the perst_b signal is already de-asserted in the
bootloader, the current reset logic fails to trigger a proper assert ->
de-assert reset sequence.
Fix the issue by always triggering the proper reset sequence.
Also explicitly select the desired reset source, i.e., perst_b, and reduce
the wait time after the device comes out of reset from 250 ms to 100 ms,
based on recommendation from the ASIC team.
Tested-by: Vladimir Dreizin <vdreizin@broadcom.com>
Tested-by: Darren Edamura <dedamura@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vladimir Dreizin <vdreizin@broadcom.com>
Reviewed-by: Trac Hoang <trhoang@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
After 459a07721c ("PCI: Build setup-irq.o for arm64"), we build
setup-irq.o for arm64, so we can use pci_fixup_irqs() on both arm and
arm64.
Remove the "#ifdef CONFIG_ARM" around the call to pci_fixup_irqs().
[bhelgaas: changelog]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Section 3.2 "Device Runtime Power Management" of pci.txt has become
outdated, so update it to correctly reflect the current code flow.
Also update the comment in local_pci_probe() to document the fact
that pm_runtime_put_noidle() is not the only runtime PM helper
function that can be used to decrement the device's runtime PM
usage counter in .probe().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Add a #define for PCIE_PHY_RX_ASIC_OUT_VALID and use it instead of a
hardcoded value.
[bhelgaas: drop PCIE_PHY_DEBUG_R0_LTSSM_MASK; updated in future patch]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
When devm_request_irq() fails, imx6_add_pcie_port() should return the real
error code instead of always returning -ENODEV.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
Commit 932c435cab ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect. We need to get the slot and then convert
it back into a devfn.
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
SR-IOV creates a virtual bus where bus->self is NULL. When we add VFs and
scan for an MSI domain, pci_set_bus_msi_domain() dereferences bus->self,
which causes a kernel NULL pointer dereference oops.
Scan up to the parent bus until we find a real bridge where we can get the
MSI domain.
[bhelgaas: changelog]
Fixes: 44aa0c657e ("PCI/MSI: Add hooks to populate the msi_domain field")
Tested-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
If pci_assign_resource() fails to assign space for a BAR, we may restore
the BAR to whatever firmware left there at boot-time (this depends on
whether the arch implements pcibios_retrieve_fw_addr()). The messages we
print are not as useful as they could be:
pci 0000:00:01.0: BAR 15: assigned [mem 0xc0000000-0xc01fffff 64bit pref]
pci 0000:01:00.0: BAR 0: no space for [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: trying firmware assignment [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: [mem size 0x10000000 pref] conflicts with PCI Bus 0000:00 [mem 0xc0000000-0xffffffff window]
The last two lines should contain the actual BAR address, not the size.
Clear IORESOURCE_UNSET so we print the address. If requesting the
firmware-assigned resource fails, mark it IORESOURCE_UNSET again.
This is a cosmetic change to clarify the message: previously, if
pci_revert_fw_address() succeeded, pci_assign_resource() cleared
IORESOURCE_UNSET anyway, so this isn't really a functional change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c50
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
c770cb4cb5 ("PCI: Mark invalid BARs as unassigned") sets IORESOURCE_UNSET
if we fail to claim a resource. If we tried to claim a bridge window,
failed, clipped the window, and tried to claim the clipped window, we
failed again because of IORESOURCE_UNSET:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
pci 0000:00:01.0: can't claim BAR 15 [mem 0xbdf00000-0xddefffff 64bit pref]: no compatible bridge window
pci 0000:00:01.0: [mem size 0x20000000 64bit pref] clipped to [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: bridge window [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: can't claim BAR 15 [mem size 0x1df00000 64bit pref]: no address assigned
The 00:01.0 window started as [mem 0xbdf00000-0xddefffff 64bit pref]. That
starts before the host bridge window [mem 0xc0000000-0xffffffff window], so
we clipped the 00:01.0 window to [mem 0xc0000000-0xddefffff 64bit pref].
But we left it marked IORESOURCE_UNSET, so the second claim failed when it
should have succeeded.
This means downstream devices will also fail for lack of resources, e.g.,
in the bugzilla below,
radeon 0000:01:00.0: Fatal error during GPU init
Clear IORESOURCE_UNSET when we clip a bridge window. Also clear
IORESOURCE_UNSET in our copy of the unclipped window so we can see exactly
what the original window was and how it now fits inside the upstream
window.
Fixes: c770cb4cb5 ("PCI: Mark invalid BARs as unassigned")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c47
Based-on-patch-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Based-on-patch-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v4.1+
In store_remove_id(), set the default return value to -ENODEV, and
overwrite it with the input buffer size if we find a matching list entry.
Then we don't need to test whether to return an error or the count.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make get_msi_addr() return phys_addr_t, not u32. This allows the MSI
target address to be above 4GB for 64bit or PAE systems.
No functional change for the current 32bit platform users as phys_addr_t
maps to u32 for them.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Implement multivector MSI IRQ setup. This allows to set up and use multiple
MSI IRQs per device.
[bhelgaas: changelog, use -EINVAL instead of -ENOSYS]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Factor out the PCI MSI message setup from the single MSI setup function.
This will be reused by the multivector MSI setup.
No functional change yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Add a msi_controller setup_irqs() method so MSI chip providers can
implement their own multivector MSI setup.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@gmail.com>
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
When pci-host-generic looks for the probe-only property, it seems to trust
the DT to be correctly written, and assumes that there is a parameter to
the property.
Unfortunately, this is not always the case, and some firmware expose this
property naked. The driver ends up making a decision based on whatever the
property pointer points to, which is likely to be junk.
Switch to the common of_pci.c implementation that doesn't suffer from this
problem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
AER errors might be recorded when powering-on devices. These errors can be
ignored, so firmware usually clears them before the OS enumerates devices.
However, firmware is not involved when devices are added via hotplug, so
the OS may discover power-up errors that should be ignored. The same may
happen when powering up devices when resuming after suspend.
Clear the AER error status registers during enumeration and resume.
[bhelgaas: changelog, remove repetitive comments]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VF BARs are read-only zero, so updating VF BARs will not have any effect.
See the SR-IOV spec r1.1, sec 3.4.1.11.
Don't update VF BARs in pci_restore_bars().
This avoids spurious "BAR %d: error updating" messages that we see when
doing vfio pass-through after 6eb7018705 ("vfio-pci: Move idle devices to
D3hot power state").
[bhelgaas: changelog, fix whitespace]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
"The most important changes in this patchset are:
- re-enable 64bit PCI bus addresses which were temporarily disabled
for PA-RISC in kernel 4.2
- fix the 64bit CAS operation in the LWS path which now enables us to
enable the 64bit gcc atomic builtins even on 32bit userspace with
64bit kernel
- fix a long-standing bug which sometimes crashed kernel at bootup
while serial interrupt wasn't registered yet"
* 'parisc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use platform_device_register_simple("rtc-generic")
parisc: Drop CONFIG_SMP around update_cr16_clocksource()
parisc: Use double word condition in 64bit CAS operation
parisc: Filter out spurious interrupts in PA-RISC irq handler
parisc: Additionally check for in_atomic() in page fault handler
PCI,parisc: Enable 64-bit bus addresses on PA-RISC
parisc: Define ioremap_uc and ioremap_wc
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
Commit 3a9ad0b ("PCI: Add pci_bus_addr_t") unconditionally introduced usage of
64-bit PCI bus addresses on all 64-bit platforms which broke PA-RISC.
It turned out that due to enabling the 64-bit addresses, the PCI logic decided
to use the GMMIO instead of the LMMIO region. This commit simply disables
registering the GMMIO and thus we fall back to use the LMMIO region as before.
Reverts commit 45ea2a5fed
("PCI: Don't use 64-bit bus addresses on PA-RISC")
To: linux-parisc@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
Pull x86 mm updates from Ingo Molnar:
"The dominant change in this cycle was the continued work to isolate
kernel drivers from MTRR legacies: this tree gets rid of all kernel
internal driver interfaces to MTRRs (mostly by rewriting it to proper
PAT interfaces), the only access left is the /proc/mtrr ABI.
This work was done by Luis R Rodriguez.
There's also some related PCI interface additions for which I've
Cc:-ed Bjorn"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/mtrr: Remove kernel internal MTRR interfaces: unexport mtrr_add() and mtrr_del()
s390/io: Add pci_iomap_wc() and pci_iomap_wc_range()
drivers/dma/iop-adma: Use dma_alloc_writecombine() kernel-style
drivers/video/fbdev/vt8623fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/s3fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/arkfb.c: Use arch_phys_wc_add() and pci_iomap_wc()
PCI: Add pci_iomap_wc() variants
drivers/video/fbdev/gxt4500: Use pci_ioremap_wc_bar() to map framebuffer
drivers/video/fbdev/kyrofb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
drivers/video/fbdev/i740fb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
PCI: Add pci_ioremap_wc_bar()
x86/mm: Make kernel/check.c explicitly non-modular
x86/mm/pat: Make mm/pageattr[-test].c explicitly non-modular
x86/mm/pat: Add comments to cachemode translation tables
arch/*/io.h: Add ioremap_uc() to all architectures
drivers/video/fbdev/atyfb: Use arch_phys_wc_add() and ioremap_wc()
drivers/video/fbdev/atyfb: Replace MTRR UC hole with strong UC
drivers/video/fbdev/atyfb: Clarify ioremap() base and length used
drivers/video/fbdev/atyfb: Carve out framebuffer length fudging into a helper
x86/mm, asm-generic: Add IOMMU ioremap_uc() variant default
...
