Commit d491f2b752 ("PCI: PM: Avoid possible suspend-to-idle issue")
attempted to avoid a problem with devices whose drivers want them to
stay in D0 over suspend-to-idle and resume, but it did not go as far
as it should with that.
Namely, first of all, the power state of a PCI bridge with a
downstream device in D0 must be D0 (based on the PCI PM spec r1.2,
sec 6, table 6-1, if the bridge is not in D0, there can be no PCI
transactions on its secondary bus), but that is not actively enforced
during system-wide PM transitions, so use the skip_bus_pm flag
introduced by commit d491f2b752 for that.
Second, the configuration of devices left in D0 (whatever the reason)
during suspend-to-idle need not be changed and attempting to put them
into D0 again by force is pointless, so explicitly avoid doing that.
Fixes: d491f2b752 ("PCI: PM: Avoid possible suspend-to-idle issue")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
PCIe r5.0, sec 7.5.3.18, defines a new 32.0 GT/s bit in the Supported Link
Speeds Vector of Link Capabilities 2. Decode this new speed. This does
not affect the speed of the link, which should be negotiated automatically
by the hardware; it only adds decoding when showing the speed to the user.
Previously, reading the speed of a link operating at this speed showed
"Unknown speed" instead of "32.0 GT/s".
Link: https://lore.kernel.org/lkml/92365e3caf0fc559f9ab14bcd053bfc92d4f661c.1559664969.git.gustavo.pimentel@synopsys.com
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") introduced the sriov_drivers_autoprobe attribute
which allows users to prevent the kernel from automatically probing a
driver for new VFs as they are created. This allows VFs to be spawned
without automatically binding the new device to a host driver, such as
in cases where the user intends to use the device only with a meta
driver like vfio-pci. However, the current implementation prevents any
use of drivers_probe with the VF while sriov_drivers_autoprobe=0. This
blocks the now current general practice of setting driver_override
followed by using drivers_probe to bind a device to a specified driver.
The kernel never automatically sets a driver_override therefore it seems
we can assume a driver_override reflects the intent of the user. Also,
probing a device using a driver_override match seems outside the scope
of the 'auto' part of sriov_drivers_autoprobe. Therefore, let's allow
driver_override matches regardless of sriov_drivers_autoprobe, which we
can do by simply testing if a driver_override is set for a device as a
'can probe' condition.
Fixes: 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding")
Link: https://lore.kernel.org/lkml/155742996741.21878.569845487290798703.stgit@gimli.home
Link: https://lore.kernel.org/linux-pci/155672991496.20698.4279330795743262888.stgit@gimli.home/T/#u
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The NVIDIA Turing GPU is a multi-function PCI device with the following
functions:
- Function 0: VGA display controller
- Function 1: Audio controller
- Function 2: USB xHCI Host controller
- Function 3: USB Type-C UCSI controller
Function 0 is tightly coupled with other functions in the hardware. When
function 0 is in D3, it gates power for hardware blocks used by other
functions, which means those functions only work when function 0 is in D0.
If any of these functions (1/2/3) are in D0, then function 0 should also be
in D0.
Commit 07f4f97d7b ("vga_switcheroo: Use device link for HDA controller")
already creates a device link to show the dependency of function 1 on
function 0 of this GPU. Create additional device links to express the
dependencies of functions 2 and 3 on function 0. This means function 0
will be in D0 if any other function is in D0.
[bhelgaas: I think the PCI spec expectation is that functions can be
power-managed independently, so I don't think this device is technically
compliant. For example, the PCIe r5.0 spec, sec 1.4, says "the PCI/PCIe
hardware/software model includes architectural constructs necessary to
discover, configure, and use a Function, without needing Function-specific
knowledge" and sec 5.1 says "D states are associated with a particular
Function" and "PM provides ... a mechanism to identify power management
capabilities of a given Function [and] the ability to transition a Function
into a certain power management state."]
Link: https://lore.kernel.org/lkml/20190606092225.17960-3-abhsahu@nvidia.com
Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Although not allowed by the PCI specs, some multi-function devices have
power dependencies between the functions. For example, function 1 may not
work unless function 0 is in the D0 power state.
The existing quirk_gpu_hda() adds a device link to express this dependency
for GPU and HDA devices, but it really is not specific to those device
types.
Generalize it and rename it to pci_create_device_link() so we can create
dependencies between any "consumer" and "producer" functions of a
multi-function device, where the consumer is only functional if the
producer is in D0. This reorganization should not affect any
functionality.
Link: https://lore.kernel.org/lkml/20190606092225.17960-2-abhsahu@nvidia.com
Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com>
[bhelgaas: commit log, reword diagnostic]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Seeing the we want to use more interrupts in the NTB MSI code
we need to be able allocate more (sometimes virtual) interrupts
in the switchtec driver. Therefore add a module parameter to
request to allocate additional interrupts.
This puts virtually no limit on the number of MSI interrupts available
to NTB clients.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
For NTB devices, we want to be able to trigger MSI interrupts
through a memory window. In these cases we may want to use
more interrupts than the NTB PCI device has available in its MSI-X
table.
We allow for this by creating a new 'virtual' interrupt. These
interrupts are allocated as usual but are not programmed into the
MSI-X table (as there may not be space for them).
The MSI address and data will then handled through an NTB MSI library
introduced later in this series.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Associated pci_epf_bar structure is needed in pci_epc_clear_bar() to
clear a BAR correctly but it is reset in pci_epf_free_space() (that
is called first) which results in pci_epc_clear_bar() failure.
Reorder the pci_epc_clear_bar()/pci_epf_free_space() calls execution
to fix the issue.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
[lorenzo.pieralisi@arm.com: reworded the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Always skip odd BAR when skipping 64bit BARs in pci_epf_test_set_bar()
and pci_epf_test_alloc_space() otherwise pci_epf_test_set_bar() will
call pci_epc_set_bar() on an odd loop index when skipping reserved 64bit
BAR.
Moreover, pci_epf_test_alloc_space() will call pci_epf_alloc_space() on
bind for an odd loop index when BAR is 64bit but leaks on subsequent
unbind by not calling pci_epf_free_space().
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
PCI endpoint test function code should honor the .bar_fixed_size parameter
from underlying endpoint controller drivers or results may be unexpected.
In pci_epf_test_alloc_space(), check if BAR being used for test
register space is a fixed size BAR. If so, allocate the required fixed
size.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Set endpoint controller pointer to NULL in pci_epc_remove_epf()
to avoid -EBUSY on subsequent call to pci_epc_add_epf().
Add a check for NULL endpoint function pointer.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
For PCI devices that have an OF node, set the fwnode as well. This way
drivers that rely on fwnode don't need the special case described by
commit f94277af03 ("of/platform: Initialise dev->fwnode appropriately").
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, there is only a 1 ms sleep after asserting PERST.
Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.
Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.
The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:
"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."
Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
Altera MSI IP is a soft IP and is only available after
an FPGA image (with design containing it) is programmed.
Make driver modulable to support use case FPGA image is programmed the
after kernel has booted, so that the driver can be loaded upon request.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Altera PCIe Rootport IP is a soft IP and is only available after
an FPGA image (whose design contains it) is programmed.
Make driver modulable to support use cases when FPGA image is
programmed after the kernel has booted, so that the driver
can be loaded upon request.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") allows the user to specify that drivers for VFs of
a PF should not be probed, but it actually causes pci_device_probe() to
return success back to the driver core in this case. Therefore by all
sysfs appearances the device is bound to a driver, the driver link from
the device exists as does the device link back from the driver, yet the
driver's probe function is never called on the device. We also fail to
do any sort of cleanup when we're prohibited from probing the device,
the IRQ setup remains in place and we even hold a device reference.
Instead, abort with errno before any setup or references are taken when
pci_device_can_probe() prevents us from trying to probe the device.
Link: https://lore.kernel.org/lkml/155672991496.20698.4279330795743262888.stgit@gimli.home
Fixes: 0e7df22401 ("PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The QCS404 platform contains a PCIe version 2.4.0 controller and a
Qualcomm PCIe2 PHY. The driver already supports version 2.4.0, for the
IPQ4019, but this support touches clocks and resets related to the PHY
as well and there's no upstream driver for the PHY.
On QCS404 we must initialize the PHY, so a separate PHY driver is
implemented to take care of this and the controller driver is updated to
not require the PHY related resources. This is done by relying on the
fact that operations in both the clock and reset framework are NOPs when
passed NULL, so we can isolate this change to only the
qcom_pcie_get_resources_2_4_0() function.
For QCS404 we also need to enable the AHB (iface) clock, in order to
access the register space of the controller, but as this is not part of
the IPQ4019 DT binding this is only added for new users of the 2.4.0
controller.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Before introducing the QCS404 platform, which uses the same PCIe
controller as IPQ4019, migrate this to use the bulk clock API, in order
to make the error paths slighly cleaner.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
If a PCI driver leaves the device handled by it in D0 and calls
pci_save_state() on the device in its ->suspend() or ->suspend_late()
callback, it can expect the device to stay in D0 over the whole
s2idle cycle. However, that may not be the case if there is a
spurious wakeup while the system is suspended, because in that case
pci_pm_suspend_noirq() will run again after pci_pm_resume_noirq()
which calls pci_restore_state(), via pci_pm_default_resume_early(),
so state_saved is cleared and the second iteration of
pci_pm_suspend_noirq() will invoke pci_prepare_to_sleep() which
may change the power state of the device.
To avoid that, add a new internal flag, skip_bus_pm, that will be set
by pci_pm_suspend_noirq() when it runs for the first time during the
given system suspend-resume cycle if the state of the device has
been saved already and the device is still in D0. Setting that flag
will cause the next iterations of pci_pm_suspend_noirq() to set
state_saved for pci_pm_resume_noirq(), so that it always restores the
device state from the originally saved data, and avoid calling
pci_prepare_to_sleep() for the device.
Fixes: 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both acpi_pci_need_resume() and acpi_dev_needs_resume() check if the
current ACPI wakeup configuration of the device matches what is
expected as far as system wakeup from sleep states is concerned, as
reflected by the device_may_wakeup() return value for the device.
However, they only should do that if wakeup.flags.valid is set for
the device's ACPI companion, because otherwise the wakeup.prepare_count
value for it is meaningless.
Add the missing wakeup.flags.valid checks to these functions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* pci/printk:
PCI: Replace dev_printk(KERN_DEBUG) with dev_info(), etc
PCI: Replace printk(KERN_INFO) with pr_info(), etc
PCI: Use dev_printk() when possible
- Use DMA-API to get tegra MSI address to prevent device DMA from
generating unwanted MSIs (Vidya Sagar)
* remotes/lorenzo/pci/tegra:
PCI: tegra: Use the DMA-API to get the MSI address
- Move IRQ register address computation inside macros (Kishon Vijay
Abraham I)
- Separate legacy IRQ and MSI configuration (Kishon Vijay Abraham I)
- Use hwirq, not virq, to get MSI IRQ number offset (Kishon Vijay Abraham
I)
- Squash ks_pcie_handle_msi_irq() into ks_pcie_msi_irq_handler() (Kishon
Vijay Abraham I)
- Add dwc support for platforms with custom MSI controllers (Kishon Vijay
Abraham I)
- Add keystone-specific MSI controller (Kishon Vijay Abraham I)
- Remove dwc host_ops previously used for keystone-specific MSI (Kishon
Vijay Abraham I)
- Skip dwc default MSI init if platform has custom MSI controller (Kishon
Vijay Abraham I)
- Implement .start_link() and .stop_link() for keystone endpoint support
(Kishon Vijay Abraham I)
- Add keystone "reg-names" DT binding (Kishon Vijay Abraham I)
- Squash ks_pcie_dw_host_init() into ks_pcie_add_pcie_port() (Kishon
Vijay Abraham I)
- Get keystone register resources from DT by name, not index (Kishon
Vijay Abraham I)
- Get DT resources in .probe() to prepare for endpoint support (Kishon
Vijay Abraham I)
- Add "ti,syscon-pcie-mode" DT property for PCIe mode configuration
(Kishon Vijay Abraham I)
- Explicitly set keystone to host mode (Kishon Vijay Abraham I)
- Document DT "atu" reg-names requirement for DesignWare core >= 4.80
(Kishon Vijay Abraham I)
- Enable dwc iATU unroll for endpoint mode as well as host mode (Kishon
Vijay Abraham I)
- Add dwc "version" to identify core >= 4.80 for ATU programming (Kishon
Vijay Abraham I)
- Don't build ARM32-specific keystone code on ARM64 (Kishon Vijay Abraham
I)
- Add DT binding for keystone PCIe RC in AM654 SoC (Kishon Vijay Abraham
I)
- Add keystone support for AM654 SoC PCIe RC (Kishon Vijay Abraham I)
- Reset keystone PHYs before enabling them (Kishon Vijay Abraham I)
- Make of_pci_get_max_link_speed() available to endpoint drivers as well
as host drivers (Kishon Vijay Abraham I)
- Add keystone support for DT "max-link-speed" property (Kishon Vijay
Abraham I)
- Add endpoint library support for BAR buffer alignment (Kishon Vijay
Abraham I)
- Make all dw_pcie_ep_ops structs const (Kishon Vijay Abraham I)
- Fix fencepost error in dw_pcie_ep_find_capability() (Kishon Vijay
Abraham I)
- Add dwc hooks for dbi/dbi2 that share the same address space (Kishon
Vijay Abraham I)
- Add keystone support for TI AM654x in endpoint mode (Kishon Vijay
Abraham I)
- Configure designware endpoints to advertise smallest resizable BAR
(1MB) (Kishon Vijay Abraham I)
- Align designware endpoint ATU windows for raising MSIs (Kishon Vijay
Abraham I)
- Add endpoint test support for TI AM654x (Kishon Vijay Abraham I)
- Fix endpoint test test_reg_bar issue (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
misc: pci_endpoint_test: Fix test_reg_bar to be updated in pci_endpoint_test
misc: pci_endpoint_test: Add support to test PCI EP in AM654x
PCI: designware-ep: Use aligned ATU window for raising MSI interrupts
PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size
PCI: keystone: Add support for PCIe EP in AM654x Platforms
dt-bindings: PCI: Add PCI EP DT binding documentation for AM654
PCI: dwc: Add callbacks for accessing dbi2 address space
PCI: dwc: Fix dw_pcie_ep_find_capability() to return correct capability offset
PCI: dwc: Add const qualifier to struct dw_pcie_ep_ops
PCI: endpoint: Add support to specify alignment for buffers allocated to BARs
PCI: keystone: Add support to set the max link speed from DT
PCI: OF: Allow of_pci_get_max_link_speed() to be used by PCI Endpoint drivers
PCI: keystone: Invoke phy_reset() API before enabling PHY
PCI: keystone: Add support for PCIe RC in AM654x Platforms
dt-bindings: PCI: Add PCI RC DT binding documentation for AM654
PCI: keystone: Prevent ARM32 specific code to be compiled for ARM64
PCI: dwc: Fix ATU identification for designware version >= 4.80
PCI: dwc: Enable iATU unroll for endpoint too
dt-bindings: PCI: Document "atu" reg-names
PCI: keystone: Explicitly set the PCIe mode
dt-bindings: PCI: Add dt-binding to configure PCIe mode
PCI: keystone: Move resources initialization to prepare for EP support
PCI: keystone: Use platform_get_resource_byname() to get memory resources
PCI: keystone: Perform host initialization in a single function
dt-bindings: PCI: keystone: Add "reg-names" binding information
PCI: keystone: Cleanup error_irq configuration
PCI: keystone: Add start_link()/stop_link() dw_pcie_ops
PCI: dwc: Remove default MSI initialization for platform specific MSI chips
PCI: dwc: Remove Keystone specific dw_pcie_host_ops
PCI: keystone: Use Keystone specific msi_irq_chip
PCI: dwc: Add support to use non default msi_irq_chip
PCI: keystone: Cleanup ks_pcie_msi_irq_handler()
PCI: keystone: Use hwirq to get the MSI IRQ number offset
PCI: keystone: Add separate functions for configuring MSI and legacy interrupt
PCI: keystone: Cleanup interrupt related macros
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.h
- Work around iproc CRS completion issues (Srinath Mannam)
- Allow smaller iproc outbound windows so driver can work on 32-bit
systems (Srinath Mannam)
- Use iproc-specific config read for PAXBv2 (not PAXB) (Srinath Mannam)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Enable iProc config read for PAXBv2
PCI: iproc: Allow outbound configuration for 32-bit I/O region
PCI: iproc: Add CRS check in config read
- Simplify imx7d_pcie_wait_for_phy_pll_lock() by using
regmap_read_poll_timeout() (Andrey Smirnov)
- Drop imx6_pcie_wait_for_link() in favor of the more generic
dw_pcie_wait_for_link() (Andrey Smirnov)
- Return -ETIMEDOUT instead of -EINVAL from
imx6_pcie_wait_for_speed_change() (Andrey Smirnov)
- Remove unused PCIE_PL_PFLR_* constants from imx6 (Andrey Smirnov)
- Use shared PHY debug register definitions in imx6 (Andrey Smirnov)
- Use BIT() in imx6 (Andrey Smirnov)
- Simplify imx6 PHY bit operations (Andrey Smirnov)
- Simplify imx6 pcie_phy_poll_ack() (Andrey Smirnov)
- Use data types that match actual imx6 PHY register width (Andrey
Smirnov)
- Mark imx6 suspend support with drvdata flags instead of checking
variants (Andrey Smirnov)
- Sleep instead of delay in imx6_pcie_enable_ref_clk() (Andrey Smirnov)
* remotes/lorenzo/pci/imx:
PCI: imx6: Use usleep_range() in imx6_pcie_enable_ref_clk()
PCI: imx6: Use flags to indicate support for suspend
PCI: imx6: Restrict PHY register data to 16-bit
PCI: imx6: Simplify pcie_phy_poll_ack()
PCI: imx6: Simplify bit operations in PHY functions
PCI: imx6: Make use of BIT() in constant definitions
PCI: dwc: imx6: Share PHY debug register definitions
PCI: imx6: Remove PCIE_PL_PFLR_* constants
PCI: imx6: Return -ETIMEOUT from imx6_pcie_wait_for_speed_change()
PCI: imx6: Drop imx6_pcie_wait_for_link()
PCI: imx6: Simplify imx7d_pcie_wait_for_phy_pll_lock()
- Restore R-Car PCIe link early in resume (Kazufumi Ikeda)
- Fix Hyper-V PCI ejection memory leak (Dexuan Cui)
- Cleanup Hyper-V PCI slots on module unload (Dexuan Cui)
- Cleanup Hyper-V PCI slot on device removal to address a race (Dexuan
Cui)
* remotes/lorenzo/pci/controller-fixes:
PCI: hv: Add pci_destroy_slot() in pci_devices_present_work(), if necessary
PCI: hv: Add hv_pci_remove_slots() when we unload the driver
PCI: hv: Fix a memory leak in hv_eject_device_work()
PCI: rcar: Add the initialization of PCIe link in resume_noirq()
- Mark ATS on AMD Stoney Radeon R7 GPU broken to avoid IOMMU issues
(Nikolai Kostrigin)
- Mark Atheros AR9462 to avoid bus reset that locks up host machine
(James Prestwood)
* pci/virtualization:
PCI: Mark Atheros AR9462 to avoid bus reset
PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken
- Add a whitelist of Root Complexes known to support peer-to-peer DMA
between Root Ports (Christian König)
* pci/peer-to-peer:
PCI/P2PDMA: Allow P2P DMA between any devices under AMD ZEN Root Complex
- Fix RPA and RPA DLPAR refcount issues (Tyrel Datwyler)
- Stop exporting pci_get_hp_params() (Alexandru Gagniuc)
- Simplify _HPP, _HPX parsing (Alexandru Gagniuc)
- Add support for _HPX Type 3 settings (Alexandru Gagniuc)
- Tell firmware we support _HPX Type 3 via _OSC (Alexandru Gagniuc)
* pci/hotplug:
PCI/ACPI: Advertise _HPX Type 3 support via _OSC
PCI/ACPI: Implement _HPX Type 3 Setting Record
PCI/ACPI: Remove the need for 'struct hotplug_params'
PCI/ACPI: Do not export pci_get_hp_params()
PCI: rpaphp: Get/put device node reference during slot alloc/dealloc
PCI: rpadlpar: Fix leaked device_node references in add/remove paths
- Enable PCIe services for host controller drivers that use managed host
bridge alloc (Jean-Philippe Brucker)
- Add quirk to clear PCIe Retrain Link bit to work around Pericom bridge
erratum (Stefan Mätje)
- Add "external-facing" DT property to identify cases where we require
IOMMU protection from untrusted devices (Jean-Philippe Brucker)
- Support fixed bus numbers from bridge Enhanced Allocation capabilities
(Subbaraya Sundeep)
* pci/enumeration:
PCI: Assign bus numbers present in EA capability for bridges
PCI: OF: Support "external-facing" property
dt-bindings: Add "external-facing" PCIe port property
PCI: Rework pcie_retrain_link() wait loop
PCI: Work around Pericom PCIe-to-PCI bridge Retrain Link erratum
PCI: Factor out pcie_retrain_link() function
PCI: Init PCIe feature bits for managed host bridge alloc
