The regmap config tables are rather similar for various generations of
the KSZ8xxx/KSZ9xxx switches. Introduce a macro which allows generating
those tables without duplication. Note that $regalign parameter is not
used right now, but will be used in KSZ87xx series switches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic SPI regmap support into the driver.
Previous patches unconver that ksz_spi_write() is always ever called
with len = 1, 2 or 4. We can thus drop the if (len > SPI_TX_BUF_LEN)
check and we can also drop the allocation of the txbuf which is part
of the driver data and wastes 256 bytes for no reason. Regmap covers
the whole thing now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The indirect function call to dev->dev_ops->get_port_addr() is expensive
especially if called for every single register access, and only returns
the value of PORT_CTRL_ADDR() macro. Use PORT_CTRL_ADDR() macro directly
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It report error message while suspend/resume test.
dmesg log:
[ 150.749962] ath10k_sdio mmc1:0001:1: hif read32 not supported
[ 150.755728] ath10k_sdio mmc1:0001:1: failed to set coverage class: expected integer microsecond value in register
Reason is sdio chip does not support set_coverage_class as well as
pcie chip, remove the set_coverage_class handler will avoid it.
callstack of the error message:
OUTLINED_FUNCTION_6+0xc/0x14 [ath10k_core]
ath10k_mac_op_set_coverage_class+0x2c/0x40 [ath10k_core]
ieee80211_reconfig+0x5d0/0x108c [mac80211]
ieee80211_resume+0x34/0x6c [mac80211]
wiphy_resume+0xbc/0x13c [cfg80211]
dpm_run_callback+0xa4/0x168
device_resume+0x1d4/0x200
async_resume+0x1c/0x34
async_run_entry_fn+0x48/0xf8
process_one_work+0x178/0x2f8
worker_thread+0x1d8/0x2cc
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
the error log will not happen after this patch applied.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Updating features and vlan_features with vlan HW offload.
Added vlan_tag fields to rx/tx ring_buff to track vlan related data.
Tested-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed some files had -or-later, however overall driver has
-only license. Clean this up.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it was discussed some time previously, driver is better to
report kernel version string, as it in a best way identifies
the codebase.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes a rare race condition of handling WMI events after
wmi_call expires.
wmi_recv_cmd immediately handles an event when reply_buf is defined and
a wmi_call is waiting for the event.
However, in case the wmi_call has already timed-out, there will be no
waiting/running wmi_call and the event will be queued in WMI queue and
will be handled later in wmi_event_handle.
Meanwhile, a new similar wmi_call for the same command and event may
be issued. In this case, when handling the queued event we got WARN_ON
printed.
Fixing this case as a valid timeout and drop the unexpected event.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace all wmi_call timeouts that are less than 100 msec to use
WIL_WMI_CALL_GENERAL_TO_MS (100 msec) as a default. Some of the
current wmi_call timeouts are too short and fails to receive its
waiting events.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Base-band chips support multi RFs chips. Add support for reading
multiple RFs temperature via debugfs.
Signed-off-by: Tzahi Sabo <stzahi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set max_msdu_size in WMI_BCAST_DESC_RING_ADD_CMD to allow FW
to optimize the buffers allocation for bcast packets.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of wil_find_cid()/wil_find_cid_by_idx() is
validated with the lower boundary value.
Check the upper boundary value as well.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clear the FW and ucode log address on device initialization to allow
user space app identify when the address was set by FW/ucode and it can
start read.
Signed-off-by: Tzahi Sabo <stzahi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RBUFCAP support added in FW.
The RBUFCAP feature is amendment to the block ack mechanism to
prevent overloading of the recipient’s memory space, which may
happen in case the link speed is higher than STA’s capability
to process or consume incoming data.
The block ack policy (ba_policy) is now controlled by FW so driver
should ignore this field.
Add new debugfs "rbufcap" to configure RBUFCAP.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver updates Tx status ring HW tail only after it finishes
processing the whole status ring, while the HW is still transmitting
from other transmit rings. This can cause back-pressure on HW if
no status entries are available.
Update HW tail of Tx status ring without waiting for the end of the
processing to help feeding back the HW with status entries and to allow
additional packet transmission.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With multiple clients and in high throughput scenarios, Tx status ring
can get full and become a bottleneck in Tx transmission.
Set the default Tx status ring size order to 13, previous value was 12.
This will double the status ring size from 4K entries to 8K entries.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the FW is reset on every interface type change, because
of various FW bugs.
FW reset is not required when switching from STA to P2P client, hence
can be skipped.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-06-26
This series contains updates to ixgbe and i40e only.
Mauro S. M. Rodrigues update the ixgbe driver to handle transceivers who
comply with SFF-8472 but do not implement the Digital Diagnostic
Monitoring (DOM) interface. Update the driver to check the necessary
bits to see if DOM is implemented before trying to read the additional
256 bytes in the EEPROM for DOM data.
Young Xiao fixes a potential divide by zero issue in ixgbe driver.
Aleksandr fixes i40e to recognize 2.5 and 5.0 GbE link speeds so that it
is not reported as "Unknown bps". Fixes the driver to read the firmware
LLDP agent status during DCB initialization, and to properly log the
LLDP agent status to help with debugging when DCB fails to initialize.
Martyna fixes i40e for the missing supported and advertised link modes
information in ethtool.
Jake fixes a function header comment that was incorrect for a PTP
function in i40e.
Maciej fixes an issue for i40e when a XDP program is loaded the
descriptor count gets reset to the default value, resolve the issue by
making the current descriptor count persistent across resets.
Alice corrects a copyright date which she found to be incorrect.
Piotr adds a log entry when the traffic class 0 is added or deleted, which
was not being logged previously.
Gustavo A. R. Silva updates i40e to use struct_size() where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the error branch for (queue > ar->hw->queues).
It is no longer needed anymore as the "queue" value is validated by
cfg80211's parse_txq_params() before the driver code gets called.
Some background:
In the old days (linux 2.6 and early 3.x), the parse_txq_params()
function did not verify the "queue" value. That's why these drivers
had to do it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 3c0efb745a ("ath9k: discard undersized packets")
the lower bound of RX packets was set to 10 (min ACK size) to
filter those that would otherwise be treated as invalid at
mac80211.
Alas, short radar pulses are reported as PHY_ERROR frames
with length set to 3. Therefore their detection stopped
working after that commit.
NOTE: ath9k drivers built thereafter will not pass DFS
certification.
This extends the criteria for short packets to explicitly
handle PHY_ERROR frames.
Fixes: 3c0efb745a ("ath9k: discard undersized packets")
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a structure for power parameters including base,
offset, limit and a function to get tx power parameters.
Then, refine flow to get tx power index through the
function.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this macro definition has different values in different chipset,
the current defined macro value is for 8822b. This will cause the
settings of 8822c be incorrect.
Remove RTW_MAX_POWER_INDEX and use max_power_index in struct rtw_chip_info
to make sure the value of different chipset is right.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support more regulatory domains including IC, KCC,
ACMA, CHILE, UKRAINE, and MEXICO. Corresponding tx
power limits for these regulatory domains are added
in tx power limit table. Besides, tx power limits in
some case are also updated to follow RF v20 for better
tx power indexes.
Channel plan mapping table are upgraded to consider
more 2G and 5G channel plans combination cases. It
allow us to identify different situations more accuratly
by channel plan IDs. In addition, mapping table for
country code and channel plan ID and mapping table
for country code and tx power limit are also updated
to follow RF v20. It allow the new enrties in tx power
limit table to be applied correctly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If phy rate is decreased, sub bandwidth may be chosen by RA.
We consider possible power limits and apply the min one;
otherwise, the tx power index may be larger than spec.
And we cross-reference power limits of vht and ht with
20/40M bandwidth in 5G to avoid values are not assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we are loading tx power limit from the power limit table, compare
the world-wide limit with the current limit and choose the lowest power
limit for the world-wide power settings.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx power limit is stored separately by 2G and 5G.
But driver did not get tx power limit from 5G and causes incorrect tx
power. Check if the channel is beyond 2G and get the corresponding tx
power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function names to make them have the same prefix "rtw_phy"
for the tx power setting routines. Only the function names and
corresponding identation are modified.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The type change from (void *) to (struct rtw_dev *) is redundant.
Just pass the right type and compiler can check that for us.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some functions that should be static are unnecessarily exposed, remove
their declaration in header file phy.h.
After resolving their declaration order, they can be declared as static.
So this commit changes nothing except the order and marking them static.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
main_proc_lock and int_lock (in mwifiex_adapter) are the only spinlocks
used in hardirq contexts. The rest are only in task or softirq contexts.
Convert every other lock from *_irq{save,restore}() variants to _bh()
variants.
This is a mechanical transformation of all spinlock usage in mwifiex
using the following:
Step 1:
I ran this nasty sed script:
sed -i -E '/spin_lock_irqsave|spin_unlock_irqrestore/ {
/main_proc_lock|int_lock/! {
s:(spin_(un|)lock)_irq(save|restore):\1_bh: ;
# Join broken lines.
:a /;$/! {
N;
s/\s*\n\s*//;
ba
}
/,.*\);$/ s:,.*\):\):
}
}' drivers/net/wireless/marvell/mwifiex/*
Step 2:
Manually delete the flags / ra_list_flags args from:
mwifiex_send_single_packet()
mwifiex_11n_aggregate_pkt()
mwifiex_send_processed_packet()
which are now unused.
Step 3:
Apply this semantic patch (coccinelle) to remove the unused 'flags'
variables:
// <smpl>
@@
type T;
identifier i;
@@
(
extern T i;
|
- T i;
... when != i
)
// </smpl>
(Usage is something like this:
make coccicheck COCCI=./patch.cocci MODE=patch M=drivers/net/wireless/marvell/mwifiex/
although this skips *.h files for some reasons, so I had to massage
stuff.)
Testing: I've played with a variety of stress tests, including download
stress tests on the same APs which caught regressions with commit
5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage"). I've
primarily tested on Marvell 8997 / PCIe, although I've given 8897 / SDIO
a quick spin as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_11n_scan_and_dispatch() and
mwifiex_11n_dispatch_pkt_until_start_win() share similar patterns, where
they perform a few different actions on the same table, using the same
lock, but non-atomically. There have been other attempts to clean up
this sort of behavior, but they have had problems (incomplete;
introducing new deadlocks).
We can improve these functions' atomicity by queueing up our RX packets
in a list, to dispatch at the end of the function. This avoids problems
of another operation modifying the table in between our dispatch and
rotation operations.
This was inspired by investigations around this:
http://lkml.kernel.org/linux-wireless/20181130175957.167031-1-briannorris@chromium.org
Subject: [4.20 PATCH] Revert "mwifiex: restructure rx_reorder_tbl_lock usage"
While the original (now-reverted) patch had good intentions in
restructuring some of the locking patterns in this driver, it missed an
important detail: we cannot defer to softirq contexts while already in
an atomic context. We can help avoid this sort of problem by separating
the two steps of:
(1) iterating / clearing the mwifiex reordering table
(2) dispatching received packets to upper layers
This makes it much harder to make lock recursion mistakes, as these
two steps no longer need to hold the same locks.
Testing: I've played with a variety of stress tests, including download
stress tests on the same APs which caught regressions with commit
5188d5453b ("mwifiex: restructure rx_reorder_tbl_lock usage"). I've
primarily tested on Marvell 8997 / PCIe, although I've given 8897 / SDIO
a quick spin as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes
for rx") breaks A-MSDU support. When A-MSDU is enable the device can
receive frames up to q->buf_size but they will be discarded in
mt76u_process_rx_entry since there is no enough room for
skb_shared_info. Fix the issue reallocating the skb and copying in the
linear area the first 128B of the received frames and in the frag_list
the remaining part
Fixes: f8f527b16d ("mt76: usb: use EP max packet aligned buffer sizes for rx")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the following sparse warning in mt7603_mcu_set_eeprom:
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: warning:
incorrect type in assignment (different base types)
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse:
expected unsigned short [usertype] addr
drivers/net/wireless/mediatek/mt76/mt7603/mcu.c:376:30: sparse: got
restricted __le16 [usertype]
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
