If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9f ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1463447 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause parameters include source address, transmit gap and pause time.
The default value of the pause source address is zero in the hardware.
Default pause parameters need to be set to the hardware. Also, when
setting new mac address, the pause source address need to be updated.
Fixes: 9dc2145d91 ("net: hns3: Add support for PFC setting in TM module")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MAC, the MTU vlaue need to be set to the hardware
too. Otherwise, the MTU value of software will be different from the MTU
value of hardware.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when changing MTU, The new MTU must need to be set to netdevice.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.
This patch fixes the bug setting a error max frame size to hardware.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a9c782822166 ("net: hns3: add support for set_pauseparam")
adds set_pauseparam support for ethtool cmd, but forgets to update
fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam().
The wrong fc_mode_last_time will be used to update flow control mode
when lldpad has been running. As a result, when using the ethtool
command "-a", user will get a wrong pause parameter.
This patch adds the fc_mode_last_time update when PFC mode is disabled.
Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The result of tqp statistics query was read with an
error position, fix it according to the user manual.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet statistics of netdev for ethtool -S, in
order to show the statistics data for current net
device.
Remove update_stats() calling because it has been
completed in hns3_get_netdev_stats().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member "stats_size" of struct hns3_stats is useless,
remove it and fix the macro definition which has uses this
struct.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member "stats_offset" was designed to indicate the offset
of each member of struct ring_stats in struct hns3_enet_ring,
but forgot to add the offset of the member in struct ring_stats.
Fixes: 496d03e960 ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error loop index was used while querying statistics data
of tqps, which may cause call trace.
Fixes: 496d03e960 ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dropped tx/rx packets number of each tqp should also
be counted into the total drop tx/rx packets numbers.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the HNS3_NIC_STATE_DOWN bit when NIC state changes.
When NIC is down, mask the packet statistics for querying
with ifconfig command. It's a common practice.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It takes more than 200 query response messages between
driver and IMP, while updating the packet statistics.
It's too heavy for IMP to update it per second.
Extend the update period of packet statistics data from
1 second to 300 seconds(if too long, the statistics may
overflow).
As a result, we need to update it while querying with
ifconfig tool to keep the statistics data fresh.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igu_rx_err_pkt indicates the same error with
mac_rx_fcs_err_pkt_num, so remove it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rxvlan offload status can only be changed by PF. Initialize
the value of NETIF_F_HW_VLAN_CTAG_RX bit of hw_features for
VFS to false, make sure user can't be able to change it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Real devices may support scatter gather(SG), so enable SG on rmnet
devices to use GSO. GSO reduces CPU cycles by 20% for a rate of
146Mpbs for a single stream TCP connection.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX checksum offload applies to TCP / UDP packets which are not
fragmented using the MAPv4 checksum trailer. The following needs to be
done to have checksum computed in hardware -
1. Set the checksum start offset and inset offset.
2. Set the csum_enabled bit
3. Compute and set 1's complement of partial checksum field in
transport header.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.
rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -
1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
value from step 3.
5. Compares the value from step 4 to the checksum value from the
TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
and the packet is passed on to network stack. If there is a
failure, then the packet is passed on as such without modifying
the ip_summed field.
The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.
If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAPv4 packet format adds support for RX / TX checksum offload.
For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly
10% CPU cycles are saved.
For receive path, there is a checksum trailer appended to the end of
the MAP packet. The valid field indicates if hardware has computed
the checksum. csum_start_offset indicates the offset from the start
of the IP header from which hardware has computed checksum.
csum_length is the number of bytes over which the checksum was
computed and the resulting value is csum_value.
In the transmit path, a header is appended between the end of the MAP
header and the start of the IP packet. csum_start_offset is the offset
in bytes from which hardware will compute the checksum if the
csum_enabled bit is set. udp_ip4_ind indicates if the checksum
value of 0 is valid or not. csum_insert_offset is the offset from the
csum_start_offset where hardware will insert the computed checksum.
The use of this additional packet format for checksum offload is
explained in subsequent patches.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The real device over which the rmnet devices are installed also
aggregate multiple IP packets and sends them as a single large
aggregate frame to the hardware. This causes degraded throughput
for TCP TX due to bufferbloat.
To overcome this problem, pacing shift value of 8 is set using the
sk_pacing_shift_update() helper. This value was determined based
on experiments with a single stream TCP TX using iperf for a
duration of 30s.
Pacing shift | Observed data rate (Mbps)
10 | 9
9 | 140
8 | 146 (Max link rate)
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done so that we can use this field for both ingress and
egress flags.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet_map_demultiplex() is only declared but not defined anywhere,
so remove it.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet devices cannot have a mux id of 255. This is validated when
assigning the mux id to the rmnet devices. As a result, checking for
mux id 255 does not apply in egress path.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already check the headroom once in rmnet_map_egress_handler(),
so this is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the current capability to the max capability. Doing so enables dual
port RoCE functionality if supported by the firmware.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When in dual port mode setting a RoCE GID for any port flows through the
master ports mlx5_core_dev. Provide an interface to set the port when
sending this command.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When mlx5_ib_add is called determine if the mlx5 core device being
added is capable of dual port RoCE operation. If it is, determine
whether it is a master device or a slave device using the
num_vhca_ports and affiliate_nic_vport_criteria capabilities.
If the device is a slave, attempt to find a master device to affiliate it
with. Devices that can be affiliated will share a system image guid. If
none are found place it on a list of unaffiliated ports. If a master is
found bind the port to it by configuring the port affiliation in the NIC
vport context.
Similarly when mlx5_ib_remove is called determine the port type. If it's
a slave port, unaffiliate it from the master device, otherwise just
remove it from the unaffiliated port list.
The IB device is registered as a multiport device, even if a 2nd port is
not available for affiliation. When the 2nd port is affiliated later the
GID cache must be refreshed in order to get the default GIDs for the 2nd
port in the cache. Export roce_rescan_device to provide a mechanism to
refresh the cache after a new port is bound.
In a multiport configuration all IB object (QP, MR, PD, etc) related
commands should flow through the master mlx5_core_dev, other commands
must be sent to the slave port mlx5_core_mdev, an interface is provide
to get the correct mdev for non IB object commands.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Generate a unique 128bit identifier for each host and pass that value to
firmware in the INIT_HCA command if it reports the sw_owner_id
capability. Each device bound to the mlx5_core driver will have the same
software owner ID.
In subsequent patches mlx5_core devices will be bound via a new VPort
command so that they can operate together under a single InfiniBand
device. Only devices that have the same software owner ID can be bound,
to prevent traffic intended for one host arriving at another.
The INIT_HCA command length was expanded by 128 bits. The command
length is provided as an input FW commands. Older FW does not have a
problem receiving this command in the new longer form.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There are two potential problems with the existing implementation.
1. Enable and disable can race after the atomic operations.
2. If a command fails the refcount is left in an inconsistent state.
Introduce a lock and perform error checking.
Fixes: a6f7d2aff6 ("net/mlx5: Add support for multiple RoCE enable")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add a missing command interface to work with a DCT. It includes: creating,
destroying and get events for.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently the less than zero error check on ret is incorrect
as it is checking a far earlier ret assignment rather than the
return from the call to wl1251_acx_arp_ip_filter. Fix this by
adding in the missing assginment.
Detected by CoverityScan, CID#1164835 ("Logically dead code")
Fixes: 204cc5c44f ("wl1251: implement hardware ARP filtering")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pausing queue without checking threshold is racy with txdone path.
Moreover we do not need pause queue on any error, but only if queue
is full - in case when we send RTS frame ( other cases of almost full
queue are already handled in rt2x00queue_write_tx_frame() ).
Patch fixes of theoretically possible problem of pausing empty
queue.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not drop &queue->tx_lock and acquire it again to pause queue when
available entries are below the threshold.
Patch should mitigate problem of frequently printed errors:
"Error - Dropping frame due to full tx queue"
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Enrico Mioso@gmail.com
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last command used to shutdown firmware might be timeout,
and trigger firmware dump in asynchronous pcie/sdio work.
The remove/shutdown handler will continue free core data
structure private/adapter, which might be dereferenced in
pcie/sdio work, finally crash the kernel.
Sync and Cancel pcie/sdio work, could be a fix for above
cornel case. In this way, the last command timeout could
be handled properly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch extend device_dump debugfs function to make it
works for usb interface.
For command timeouts, USB firmware will automatically emit
firmware dump events, so we don't implement device_dump().
For user-initiated dumps, we trigger it by issue firmware
dump event command to firmware, as there is no command
response, do not start 10s timer.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
