Add missing printk severity levels by adopting pr_foo() calls for the
platform_driver and dev_foo() calls for the nubus_driver.
Avoid KERN_CONT usage as per advice from checkpatch.
Avoid #ifdef around printk calls.
Don't log driver probe messages after calling register_netdev().
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves an old issue preventing any NuBus SONIC NICs from
working in a Mac with an on-board SONIC device.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that the single port Ether controllers having TSU (like SH7734/
R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100
currently has -- they also don't have the TSU registers related e.g. to
passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port'
flag and use it as a new criterion for taking a "short path" in the TSU
init sequence in order to avoid writing to the non-existent registers...
Fixes: f0e81fecd4 ("net: sh_eth: Add support SH7734")
Fixes: 73a0d90730 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSU_QTAG0/1 registers found in the Gigabit Ether controllers actually
have the same long name as the TSU_QTAGM0/1 registers in the early Ether
controllers: Qtag Addition/Deletion Set Register (Port 0/1 to 1/0); thus
there's no need to make a difference in sh_eth_tsu_init() between those
controllers. Unfortunately, we can't just remove TSU_QTAG0/1 from the
register *enum* because that would break the ethtool register dump...
Fixes: b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't flush batched XDP packets through xdp_do_flush_map(), this
will cause packets stall at TX queue. Consider we don't do XDP on NAPI
poll(), the only possible fix is to call xdp_do_flush_map()
immediately after xdp_do_redirect().
Note, this in fact won't try to batch packets through devmap, we could
address in the future.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for tuntap, all other drivers' XDP was implemented at NAPI
poll() routine in a bh. This guarantees all XDP operation were done at
the same CPU which is required by e.g BFP_MAP_TYPE_PERCPU_ARRAY. But
for tuntap, we do it in process context and we try to protect XDP
processing by RCU reader lock. This is insufficient since
CONFIG_PREEMPT_RCU can preempt the RCU reader critical section which
breaks the assumption that all XDP were processed in the same CPU.
Fixing this by simply disabling preemption during XDP processing.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 762c330d67. The
reason is we try to batch packets for devmap which causes calling
xdp_do_flush() in the process context. Simply disabling preemption
may not work since process may move among processors which lead
xdp_do_flush() to miss some flushes on some processors.
So simply revert the patch, a follow-up patch will add the xdp flush
correctly.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 762c330d67 ("tuntap: add missing xdp flush")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable dma is initialized with a value that is never read, later
on it is re-assigned a new value, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:584:13: warning: Value
stored to 'dma' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make it so that all rings allocations are made as part of q_vector.
The advantage to this is that we can keep all of the memory related to
a single interrupt in one page.
The goal is to bring the logic of handling rings closer to ixgbe.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to commit a50c29dd09
("ixgbe: Make certain that all frames fit minimum size requirements")
Make sure that any packet we attempt to transmit will meet minimum
size requirements.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following the logic from commit 2de6aa3a66
("ixgbe: Add support for padding packet")
Add support for providing a buffer with headroom and tail room
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN. With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add calls for netif_set_real_num_t/rx_queues() in ixgbevf_open().
Make sure that calls to ixgbevf_open() are rtnl protected and improve
the error handling when setting up multiple queues.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit 8649aaef40
("igb: Add support for using order 1 pages to receive large frames")
Add support for using 3K buffers in order 1 page. We are reserving 1K for
now to have space available for future tail room and head room when we
enable build_skb support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce legacy-rx private flag that will allow switching between the
old and new (build_skb based) Rx code paths. The implementation is the
same as in commit e08912985b
("igb: Add support for ethtool private flag to allow use of legacy Rx")
This provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on commit 3456fd5342
("igb: Use page_address offset from page instead of masking virtual address")
Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On hardware which supports timestamping all packets, the timestamps are
recorded in the packet buffer, and the driver no longer uses or reads
the registers. This makes the logic for checking and clearing Rx
timestamp hangs meaningless.
If we run the ixgbe_ptp_rx_hang() function in this case, then the driver
will continuously spam the log output with "Clearing Rx timestamp hang".
These messages are spurious, and confusing to end users.
The original code in commit a9763f3cb5 ("ixgbe: Update PTP to support
X550EM_x devices", 2015-12-03) did have a flag PTP_RX_TIMESTAMP_IN_REGISTER
which was intended to be used to avoid the Rx timestamp hang check,
however it did not actually check the flag before calling the function.
Do so now in order to stop the checks and prevent the spurious log
messages.
Fixes: a9763f3cb5 ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function xenvif_rx_skb is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
drivers/net/xen-netback/rx.c:422:6: warning: symbol 'xenvif_rx_skb'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit pattern LOOPBACK_SGMII is being bit-wise or'd twice; remove the
redundant 2nd LOOPBACK_SGMII
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns that 'resource_id' is not initialized if we don't come though
any of the three 'case' statements before:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c: In function 'mlxsw_sp_kvdl_part_init':
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:275:8: error: 'resource_id' may be used uninitialized in this function [-Werror=maybe-uninitialized]
In the current code, that won't happen, but it's more robust to explicitly
handle this by returning a failure from mlxsw_sp_kvdl_part_init.
Fixes: 887839e696 ("mlxsw: spectrum_kvdl: Add support for dynamic partition set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculating the number of entries now uses 64-bit arithmetic that
causes a link error on 32-bit architectures:
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.o: In function `mlxsw_sp_kvdl_init':
spectrum_kvdl.c:(.text+0x51c): undefined reference to `__aeabi_uldivmod'
We could probably use a 32-bit division here as before, but since this is
not in a performance critical path, div_u64() seems cleaner here.
Fixes: 887839e696 ("mlxsw: spectrum_kvdl: Add support for dynamic partition set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable pool is being assigned zero and then in the following for-loop
is it being set to zero again. Remove the redundant first assignment.
Cleans up clang warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c:61:2: warning: Value stored
to 'pool' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Not all boards have the interrupt output from the switch connected to
a GPIO line. In such cases, phylib has to poll the internal PHYs,
rather than receive an interrupt when there is a change in the link
state. phylib polls once per second, and per PHY reads around 4
words. With a switch typically having 4 internal PHYs, this means 16
MDIO transactions per second.
Rather than performing this phylib level polling, have the driver poll
the interrupt status register. If the status register indicates an
interrupt condition processing of interrupts in the same way as if a
GPIO was used.
Polling 10 times a second places less load on the MDIO bus. But rather
than taking on average 0.5s to detect a link change, it takes less
than 0.05s. Additionally, other interrupts, such as the watchdog, ATU
and VTU violations will be reported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only allowed VLAN devices to be put in a VLAN-unaware
bridge, but some users need the ability to enslave physical ports as
well.
This is achieved by mapping the port and VID 1 to the bridge's vFID,
instead of the port and the VID used by the VLAN device.
The above is valid because as long as the port is not enslaved to a
bridge, VID 1 is guaranteed to be configured as PVID and egress
untagged.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever ath10k firmware discards a packet (HTT_TX_COMPL_STATE_DISCARD
flag), the skb is freed and mac80211 does not get feedback through
ieee80211_tx_status().
Instead, make sure that the IEEE80211_TX_STAT_ACK flag is disabled and
let the packet go through, like ath9k does.
Signed-off-by: Ignacio Nunez Hernanz <nacho.nunez@aoifes.com>
[kvalo@codeaurora.org: rebase patch manually]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit c713fb071e ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For ages iproute2 has used `struct rtmsg` as the ancillary header for
FIB rules and in the process set the protocol value to RTPROT_BOOT.
Until ca56209a66 ("net: Allow a rule to track originating protocol")
the kernel rules code ignored the protocol value sent from userspace
and always returned 0 in notifications. To avoid incompatibility with
existing iproute2, send the protocol as a new attribute.
Fixes: cac56209a6 ("net: Allow a rule to track originating protocol")
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until this point it wasn't possible to activate IB representors
when switching to switchdev mode, remove this limitation.
We trigger reload of the PF IB interface in order to make sure that
already allocated resources are invalid and new resources will be opened
correctly with all the limitations of switchdev mode applied (only raw
packet capabilities, without RoCE). We also move the remove/add to a
place where the E-Switch mode is set/unset to better control when to
trigger this action, this will allow the IB side to start in the correct
mode.
For better code reuse, create a function which reloads an interface and
export it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Under switchdev mode we insert an eswitch miss rule causing any
unmatched traffic to be sent towards the PF vport. This miss rule can
be optimized if we break it to two, one case is for multicast traffic and
the other for unicast.
Breaking the miss rule into two (unicast and multicast) allows the firmware
to program the hardware in a more efficient way.
Using ConncetX-5 Ex with IXIA and testpmd (which use IB representors):
IXIA -> NIC -> PF -> IB representor -> NIC -> VF:
- Without this optimization: 9.2 MPPS.
- With this optimization: 18 MPPS.
VF -> NIC -> IB representor-> PF -> NIC -> IXIA:
- Without this optimization: 17 MPPS.
- With this optimization: 23.4 MPPS.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The max FTE number should be the max number of SQs that can be opened.
Ethernet representors open one SQ each. Once we add IB representor this
will increase (depends on the user). For now lets start with 31
per IB representor and if needed increase in the future.
This increase only affects the number of FTEs in the slow path FDB,
offloaded rules (done via TC on the fast path portion of the FDB)
aren't affected.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In preparation for IB representors, move representors structs to a global
scope, also expose functions needed for registration, unregistration,
eswitch mode and creating a flow rule to direct traffic from SQs to the
right VF.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a callback interface to get a protocol device (per representor type).
The Ethernet representors will expose their netdev via this interface.
This functionality can be later used by IB representor in order to find the
corresponding net device representor.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
r8168_check_dash() returns false anyway for all chip versions not
supporting dash. So we can simplify the check conditions.
In addition change the check functions to return bool instead of int,
because they actually return a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if BIOS enables WOL in the chip, settings are inconsistent
because the device isn't marked as wakeup-enabled (if not done
explicitly via userspace tools). This causes issues with suspend/
resume because mdio_bus_phy_may_suspend() checks whether device is
wakeup-enabled. In detail MDIO bus access in phy_suspend() can fail
because the MDIO bus is disabled.
In the history of the driver we find two competing approaches:
8f9d513803 "r8169: remember WOL preferences on driver load" prefers
to preserve what the BIOS may have set, whilst bde135a672
"r8169: only enable PCI wakeups when WOL is active" disabled PCI
wakeup per default to work around a bug on one platform.
Seems like nobody complained after the latter patch about non-working
WOL, what makes me think that nobody uses WOL w/o configuring it
explicitly.
My opinion:
Vast majority of users doesn't use WOL even if the BIOS enables it in
the chip. And having WOL being active keeps the PHY(s) from powering
down if being idle.
If somebody needs WOL, he can enable it during boot, e.g. by
configuring systemd.link/WakeOnLan.
Therefore, to make WOL consistent again, disable it per default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:
[10642.528443] BUG: KASAN: use-after-free in
macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352] dump_stack+0x5c/0x7c
[10643.035325] print_address_description+0x75/0x290
[10643.092938] kasan_report+0x28d/0x390
[10643.137971] ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963] macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978] macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532] rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964] kasan_kmalloc+0xa6/0xd0
[10646.343746] kmem_cache_alloc_trace+0xf1/0x210
[10646.397826] macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386] macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728] rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549] __kasan_slab_free+0x138/0x180
[10647.111468] kfree+0x9e/0x1c0
[10647.147869] macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411] rollback_registered_many+0x5b9/0xb10
[10647.268715] rollback_registered+0xd9/0x190
[10647.319675] register_netdevice+0x8eb/0xc70
[10647.370635] macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195] macvtap_newlink+0x171/0x260 [macvtap]
Commit d02fd6e7d2 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d2 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declaring a static function in a header leads to a warning every
time that header gets included without the function being used:
In file included from drivers/net/dsa/mv88e6xxx/chip.c:42:
drivers/net/dsa/mv88e6xxx/ptp.h:92:13: error: 'mv88e6xxx_hwtstamp_work' defined but not used [-Werror=unused-function]
static long mv88e6xxx_hwtstamp_work(struct ptp_clock_info *ptp)
In file included from drivers/net/dsa/mv88e6xxx/chip.c:38:
drivers/net/dsa/mv88e6xxx/global2.h:355:12: error: 'mv88e6xxx_g2_wait' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_wait(struct mv88e6xxx_chip *chip, int reg, u16 mask)
^~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:350:12: error: 'mv88e6xxx_g2_update' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_update(struct mv88e6xxx_chip *chip, int reg, u16 update)
^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:345:12: error: 'mv88e6xxx_g2_write' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_write(struct mv88e6xxx_chip *chip, int reg, u16 val)
^~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:340:12: error: 'mv88e6xxx_g2_read' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_read(struct mv88e6xxx_chip *chip, int reg, u16 *val)
This marks all such functions in dsa inline to make sure we don't warn
about them.
Fixes: c6fe0ad2c3 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Fixes: 0d632c3d6f ("net: dsa: mv88e6xxx: add accessors for PTP/TAI registers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMDA0099-0001 platform can support the 1x10G + 1x25G mixed mode
operation. Recently, firmware has been added for this configuration
mode.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to build separate objects we need to provide
Kbuild with a Makefile in each directory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Various updates across wireless.
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
