Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The rfh for 22560 devices has changed so it supports now
the same arch of using used and free lists, but different
structures to support the last.
Use the new structures, hw dependent, to manage the lists.
bd, the free list, uses the iwl_rx_transfer_desc,
in which the vid is stored in the structs' rbid
field, and the page address in the addr field.
used_bd, the used list, uses the iwl_rx_completion_desc
struct, in which the vid is stored in the structs' rbid
field.
rb_stts, the hw "write" pointer of rx is stored in a
__le16 array, in which each entry represents the write
pointer per queue.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For FW_PORT_ACTION_GET_PORT_INFO32 messages, the
u.info32.lstatus32_to_cbllen32 is 32-bit Big Endian.
We need to translate that to CPU Endian in order to
test F_FW_PORT_CMD_DCBXDIS32.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning the command queue, the value of the HEAD register is not
in the range of next_to_clean and next_to_use, meaning that this value
is invalid. This also means that there is a hardware error and the
hardware will trigger a reset soon. At this time we should return an
error code instead of 0, and HCLGE_STATE_CMD_DISABLE needs to be set to
prevent sending command again.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
drivers/net/ethernet/neterion/Kconfig => "Exar devices"
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids that sparse complains about casts to restricted __be32.
Fixes: a3cdaa69e4 ("cxgb4: Adds CPL support for Shared Receive Queues")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a7 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b8f3c8d30 ("virtio_net: Add XDP related stats") tries to
count TX XDP stats in virtnet_receive(). This will cause several
issues:
- virtnet_xdp_sq() was called without checking whether or not XDP is
set. This may cause out of bound access when there's no enough txq
for XDP.
- Stats were updated even if there's no XDP/XDP_TX.
Fixing this by reusing virtnet_xdp_xmit() for XDP_TX which can counts
TX XDP counter itself and remove the unnecessary tx stats embedded in
rx stats.
Reported-by: syzbot+604f8271211546f5b3c7@syzkaller.appspotmail.com
Fixes: 5b8f3c8d30 ("virtio_net: Add XDP related stats")
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver doesn't support secured boot flow, hence
prevent FW download in case HW is configured for such a flow.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single MSI is the current default configuration.
With multiple MSI interrupts configuration, Tx/Rx processing could
run in parallel on different CPU cores and allow better balance
between the cores.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device can be different from the default name.
In such a case use a corresponding board file name.
If such a board file is not present FW download procedure will fail.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW can support BACK window size 64 for performance improvements.
A new FW capability is added for notifying the host on the increased
max BACK win size support.
Defining WIL_MAX_AGG_WSIZE_64 and WIL_MAX_AMPDU_SIZE_128 to be used
in this case.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scan is allowed only on client interfaces (STA/P2P).
Allow scan on AP interface so that the AP can discover rouge
or unauthorized neighbor APs.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With some tool chains compilation fails due to type
mismatch of the arguments passed to min().
Use min_t() to solve these compilation errors.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend MSI support to 3-MSI in order to load balance the tx\rx
interrupts between different cores.
use_msi module parameter has changed to n_msi. Usage:
- Set n_msi to 0 for using INTx
- Set n_msi to 1 for using single MSI
- Set n_msi to 3 for using 3-MSI
In 3-MSI configuration MSI 0 is used for TX interrupts, MSI 1
is used for RX interrupts and MSI 2 is used for MISC interrupts.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device is different from the default name.
This patch searches for Talyn specific FW file name and fallback
to the default FW file in case it is not present.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
