If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4
[2]: 0519359784 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76
[4]: e542a2269f ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76 ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4ae0169fd1.
This change in the handling of the coalesce timer is causing regression on
(at least) amlogic platforms.
Network will break down very quickly (a few seconds) after starting
a download. This can easily be reproduced using iperf3 for example.
The problem has been reported on the S805, S905, S912 and A113 SoCs
(Realtek and Micrel PHYs) and it is likely impacting all Amlogics
platforms using Gbit ethernet
No problem was seen with the platform using 10/100 only PHYs (GXL internal)
Reverting change brings things back to normal and allows to use network
again until we better understand the problem with the coalesce timer.
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds zero-copy Tx support for AF_XDP sockets. It implements
the ndo_xsk_async_xmit netdev ndo and performs all the Tx logic from a
NAPI context. This means pulling egress packets from the Tx ring,
placing the frames on the NIC HW descriptor ring and completing sent
frames back to the application via the completion ring.
The regular XDP Tx ring is used for AF_XDP as well. This rationale for
this is as follows: XDP_REDIRECT guarantees mutual exclusion between
different NAPI contexts based on CPU id. In other words, a netdev can
XDP_REDIRECT to another netdev with a different NAPI context, since
the operation is bound to a specific core and each core has its own
hardware ring.
As the AF_XDP Tx action is running in the same NAPI context and using
the same ring, it will also be protected from XDP_REDIRECT actions
with the exact same mechanism.
As with AF_XDP Rx, all AF_XDP Tx specific functions are added to
i40e_xsk.c.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch prepares for the upcoming zero-copy Tx functionality, by
moving common functions and refactor chunks of code into re-usable
functions, used both by the regular path and zero-copy path.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds zero-copy Rx support for AF_XDP sockets. Instead of
allocating buffers of type MEM_TYPE_PAGE_SHARED, the Rx frames are
allocated as MEM_TYPE_ZERO_COPY when AF_XDP is enabled for a certain
queue.
All AF_XDP specific functions are added to a new file, i40e_xsk.c.
Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS
will allocate a new buffer and copy the zero-copy frame prior passing
it to the kernel stack.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch prepares for the upcoming zero-copy Rx functionality, by
moving/changing linkage of common functions, used both by the regular
path and zero-copy path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In this commit, the Rx path is refactored some, as a step torwards the
introduction AF_XDP Rx zero-copy.
The page re-use counter is moved into the i40e_reuse_rx_page, instead
of bumping the counter in many places. The Rx buffer page clearing is
moved for better readability. Lastely, functions to update statistics
and bump the XDP Tx ring are introduced.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add functions for queue pair enable/disable. Instead of resetting the
whole device, only the affected queue pair is disabled or enabled.
This plumbing is used in a later commit, when zero-copy AF_XDP support
is introduced.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make nfp_rtsym_{read,write}_le() and nfp_rtsym_map() use the new
target resolution helpers to allow accessing in-cache symbols.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTsyms may have special encodings for more complex symbol types.
For example symbols which are placed in external memory unit's
cache directly, constants or local memory. Add set of helpers
which will check for those special encodings and handle them
correctly.
For now only add direct cache accesses, we don't have a need to
access the other ones in foreseeable future.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error prints to CPP target encoding/decoding logic, otherwise
it's quite hard to pin point the reasons why read or write
operations fail.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon need the MU locality field offset much more
often than just for decoding MIP address. Save it in nfp_cpp
for quick access. Note that we can already reuse the target
config from nfp_cpp, no need to do the XPB read.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a switch statement instead of ifs for code dependent
on chip version. While at it make sure we fail for unknown
chip revisions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NFP5000 to supported chips, the chip is backward compatible
with NFP4000 and NFP6000, so core PCIe code needs to handle it
the same way as 4k and 6k.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management FW can adjust some of the information in the HWinfo table
at runtime. In some cases reading the table directly will not yield
correct results. Add a NSP command for looking up information.
Up until now we weren't making use of any of the values which may
get adjusted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable easier FW distribution NFP can now automatically
select between FW stored on the flash and loaded from the
kernel.
If FW loading policy is set to auto it will compare the
versions of FW from the host and from the flash and load
the newer one. If FW type doesn't match (e.g. one advanced
application vs another) the FW from the host takes precedence,
unless one of them is the basic NIC firmware, in which case
the non-basic-NIC FW is selected.
This automatic selection mechanism requires we inform user
what the verdict was. Print a message to the logs explaining
the decision and the reason.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flash may contain a default NFP application FW. This application
can either be put there by the user (with ethtool -f) or shipped
with the card. If file system FW is not found, attempt to load
this flash stored app FW.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a fair number of arguments to nfp_nsp_command()
family of functions. Encapsulate them into structures to make
adding new ones easier. No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-08-28
This series contains new features and implementation updates for the
ice driver.
Anirudh reworks the current flex programming logic to add support for
a second flex descriptor profile. Updated the transmit scheduler
code to handle changes to the spec, specifically the firmware expects
a 4KB buffer at all times so fix the default scheduler topology buffer
size. Also the maximum children per node per layer is replaced by
maximum sibling group size. Adds a check to ensure a reset is not in
progress before exercising a control queue operation. Refactored the
switch rule management functions and structures to simply the logic and
to add a common function to search for a rule entry and add a new rule
entry. Refactored the VSI allocation, deletion and rebuild flow so that
on reset we can restore all the filters that were previously added. Did
some spring cleaning of define names and macros.
Dan updates the admin queue command for requesting resource ownership
to the latest specification by adding new enum's and change the locks.
Zhenning optimizes the driver by using the existing buffer in a
structure directly versus a local array.
Chinh implements handlers for ethtool for get and set link settings.
Sudheer implements transmit hang/timeout detection and malicious driver
detection in the driver.
Md Fahad Iqbal implements the get and set bridge mode operations.
Hieu adds the ability for firmware logging during initialization.
Brett updates the driver to only enable VSI transmit and receive pruning
when VLAN 0 is active, and when VLAN 0 is removed/not active, pruning is
disabled.
Akeem adds a flag to use for stopping the service task.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There seems to be a problem in the x540's internal switch wherein if SR-IOV
mode is enabled and an offloaded IPsec packet is sent to a local VF,
the packet is silently dropped. This might never be a problem as it is
somewhat a corner case, but if someone happens to be using IPsec offload
from the PF to a VF that just happens to get migrated to the local box,
communication will mysteriously fail.
Not good.
A simple way to protect from this is to simply not allow any IPsec offloads
for outgoing packets when num_vfs != 0. This doesn't help any offloads that
were created before SR-IOV was enabled, but we'll get to that later.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the IPsec offload support code. This is based off of the similar
code in ixgbe, but instead of writing the SA registers, the VF asks
the PF to setup the offload by sending the offload information to the
PF via the standard mailbox.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an add and a delete message for IPsec offload requests from
the VF. These call into the IPsec functions that can translate
the message buffer into a useful IPsec offload.
These new messages bump the mbox API version to 1.4.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a private flag to expressly enable support for VF IPsec offload.
The VF will have to be "trusted" in order to use the hardware offload,
but because of the general concerns of managing VF access, we want to
be sure the user specifically is enabling the feature.
This is likely a candidate for becoming a netdev feature flag.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restore the IPsec hardware IP table after reloading the SA tables.
This doesn't make much difference now, but will matter when we add
support for VF IPsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The software SA record counters should not be cleared when clearing
the hardware tables. This causes the counters to be out of sync
after a driver reset.
Fixes: 63a67fe229 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VLAN pruning is not valid when VLAN 0 is not active. If VLAN
pruning is enabled and VLAN 0 is not active (8021q driver not loaded)
then normal, non-VLAN, traffic will not pass.
TX/RX VLAN pruning is enabled when the VLAN 0 is added to the
active_vlan bitmap and it is disabled when VLAN 0 is removed from the
active_vlan bitmap.
So, only enable VLAN pruning when VLAN 0 is active. Setting RX VLAN
pruning causes the switch to drop received VLAN packets when there
are no matching VLAN ids in the associated VSI's switch filters. Setting
TX pruning makes it so the switch will not send out any packets with
VLAN tags that don't match the associated VSI's switch filters.
With this patch, if the VF or PF tries to send a VLAN tagged packet with
a VLAN tag that it does not have a pruning rule for it will trigger an
MDD event. For example, if PF0 has VLAN10 and VLAN11 interfaces and
scapy is used to send a packet with VLAN8 then the MDD is triggered.
Also make ice_vsi_kill_vlan return a value which the caller can check
before updating VLAN related data structures (counts, pruning bits, etc.).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To enable FW logging, the "cq_en" and "uart_en" enable bits of the
"fw_log" element in struct ice_hw need to set accordingly based on
some user-provided parameters during driver loading. To select which
FW log events to be emitted, the "cfg" elements of corresponding FW
modules in the "evnts" array member of "fw_log" need to be configured.
Signed-off-by: Hieu Tran <hieu.t.tran@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_bridge_getlink returns the current bridge mode using
ndo_dflt_bridge_getlink and the mode parameter available in
first_switch->bridge_mode.
ice_bridge_setlink is invoked when the bridge mode needs to
changed. The value to be changed to is available as a netlink
message which is parsed in this function. If the mode has to
be changed, switch_flags is set appropriately (set ALLOW_LB
for VEB mode and clear it for VEPA mode) and ice_aq_update_vsi
is called. Also change the unicast switch filter rules.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a malicious operation is detected, the firmware triggers an
interrupt, which is then picked up by the service task (specifically by
ice_handle_mdd_event). A reset is scheduled if required.
Tx hang detection works in a similar way, except the logic here monitors
the VSI's Tx queues and tries to revive them if stalled. If the hang is
not resolved, the kernel eventually calls ndo_tx_timeout, which is
handled by ice_tx_timeout.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the existing register definitions.
1) Several instances of long defines names used in the BIT() macro
were replaced to use the actual values they represent. As a
result some defines for shifts (ending with _S) that were used
only to create bitmasks were removed completely.
2) Apply more consistent tab spacing.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors aspects of the VSI allocation, deletion and rebuild
flow. Some of the more noteworthy changes are described below.
1) On reset, all switch filters applied in the hardware are lost. In
the rebuild flow, only MAC and broadcast filters are being restored.
Instead, use a new function ice_replay_all_fltr to restore all the
filters that were previously added. To do this, remove calls to
ice_remove_vsi_fltr to prevent cleaning out the internal bookkeeping
structures that ice_replay_all_fltr uses to replay filters.
2) Introduce a new state bit __ICE_PREPARED_FOR_RESET to distinguish the
PF that requested the reset (and consequently prepared for it) from
the rest of the PFs. These other PFs will prepare for reset only
when they receive an interrupt from the firmware.
3) Use new functions ice_add_vsi and ice_free_vsi to create and destroy
VSIs respectively. These functions accept a handle to uniquely
identify a VSI. This same handle is required to rebuild the VSI post
reset. To prevent confusion, the existing ice_vsi_add was renamed to
ice_vsi_init.
4) Enhance ice_vsi_setup for the upcoming SR-IOV changes and expose a
new wrapper function ice_pf_vsi_setup to create PF VSIs. Rework the
error handling path in ice_setup_pf_sw.
5) Introduce a new function ice_vsi_release_all to release all PF VSIs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is an adaptation of the work originally done by Grishma
Kotecha <grishma.kotecha@intel.com> that in summary refactors the
switch filtering logic in the driver. More specifically,
- Update the recipe structure to also store list of rules
- Update the existing code for recipes like MAC, VLAN, ethtype etc to
use list head that is attached to switch recipe structure
- Add a common function to search for a rule entry and add a new rule
entry. Update the code to use this new function.
- Refactor the rem_handle_vsi_list function to simplify the logic
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
