Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using the firmware api it can fail simply because firmware does
not like the request or it fails due to issues in the host interface.
Currently, there is only a single error code which is confusing. So
adding a parameter to pass the firmware error separately and in case
of a firmware error always return -EBADE to user-space.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The protocol layer api defines callbacks for dongle commands.
Although not really well documented these should only return an
error code in case of an error, or 0 upon success. In the bcdc
protocol it can return value above 0 and we carry a fix in the
caller of the protocol layer api. This patch makes it adhere to
the intent of the api as described above.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Events processing requires locking of bus mutex, which is also used by
cfg80211 layer before calling several of cfg80211 callbacks. Since all
cfg80211 callbacks in qtnfmac driver also lock bus mutex, this
potentially may lead to a deadlock.
Do not use bus lock for event processing. Use RTNL lock instead to
serialize events and commands processing threads.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function qtnf_scan_done makes use of mutexes which is wrong
since it may be called from timer context. Move scan timeout
handler from timer to deferred work.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA does not reconnect to the same AP after disconnect. The reason is
that STA is marked as disconnected in cfg80211 disconnect callback.
This is too early since in this case qtnfmac event handler skips
cfg80211_disconnected call when processing disconnect event from
the card. As a result, wdev is left in an inconsistent state.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate new interface combinations using wireless core checks when new
interface is added or when the type of existing interface is modified.
This is performed to make sure that new interface combination is supported
by hardware. As a result, invalid interface combinations are rejected early,
rather than passed to hardware with sometimes unpredictable results.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update existing code handling configuration of supported interface
combinations. Current implementation is not complete since it does
not report multiple interface combinations which are incompatible
with each other. Instead current implementation packs all the
supported combinations into single entry.
In fact currently qsr10g wireless card supports the following
two distinct interface combinations:
1. STA/repeater: 1 STA and/or 1 AP
{
{ .max = 1, .types = NL80211_IFTYPE_AP},
{ .max = 1, .types = NL80211_IFTYPE_STA},
}
2. AP/mBSS
{
{ .max = 8, .types = NL80211_IFTYPE_AP},
}
The list of supported configuration is reported by firmware during
wireless card bring-up. Communication protocol between firmware
and host has been updated accordingly in order to accommodate passing
multiple interface combination entries.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable reporting of qtnfmac hardware and firmware details
using ethtool command.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various bits of hardware and firmware versions are useful for debug
and troubleshooting. Get more information from the wireless card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 32-bit platforms packet counters are stored in a net_device_stats struct
as unsigned long integers. As a result, after some time of network activity
an overflow takes place in network packet counters. This patch makes use of
new structs for holding interface statistics.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hardware encryption seems to break encrypted unicast mgmt tx.
Unfortunately the hardware TXWI header does not have a bit to indicate
that a frame is software encrypted, so sw-encrypted frames need to use a
different WCID. For that to work, the CCMP PN needs to be generated in
software, which makes things a bit slower, so only do it for keys that
also need to tx management frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Johannes Berg says:
====================
Less than a handful of changes:
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
====================
A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category. One adding
a rhashtable and another adding a workqueue.
Signed-off-by: David S. Miller <davem@davemloft.net>
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Final few patches before the merge window, nothing really special.
ath9k
* add MSI support (not enabled by default yet)
rtlwifi
* support A-MSDU in A-MPDU aggregation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
One last set of fixes for regression submitted during the last few days.
bcma & ssb
* fix older build problems which (apparently) recently became more
frequent in certain MIPS configurations
brcmfmac
* continue driver initialisation even if CLM blob (firmware) file is
not found
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that A-MSDU deaggregation is done in software,
we set this flag to support the A-MSDU in A-MPDU
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex configure antenna by rfe_type that is RF type programmed in efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit implement the common function to sort old features, and add
more new features that are get_supported_feature, get_supported_version,
get_ant_det_val, ble_scan_type, ble_scan_para, bt_dev_info,
forbidden_slot_val, afh_map and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these typedefs are only referenced in a single location later
in this header. Thus, they are easily removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove global variables, so btcoexist can support multiple instances
simultaneously.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After mac power-on sequence, wifi will start to work so notify btcoex the
event to configure registers especially related to antenna. This will not
only help to assign antenna but also to yield better user experience.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP change bandwidth setting from 20M to 40M, STA may use old 20M AP
information to association with AP. Driver unlink bss in the
.bss_info_changed of ieee80211_ops to make sure that later scan can get
correct AP bandwidth capability.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there is no connection, driver will enter IPS state. Meanwhile, it
fails to scan channel 1 by the command 'iw dev wlan0 scan freq 2412',
because hardware channel setting lose after IPS. Thus, restore channel
setting from hw->conf.channel set by last rtl_op_config().
Signed-off-by: Tim Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enter/leavel IPS and LPS are large critical section, and they can't use
sleep function because running in atomic-context, which own a spin_lock.
In commit ba9f93f82a ("rtlwifi: Fix enter/exit power_save"), it moves
LPS functions to thread-context, so this commit can simply change LPS's
spin lock to mutex.
Considering IPS functions, rtl_ips_nic_on() may be called by TX tasklet
(softirq-context) that check whether packet is auth frame. Fortunately,
current mac80211 will ask driver to leave IPS using op_config with
changed flag IEEE80211_CONF_CHANGE_IDLE, before issuing auth frame, so
IPS functions can run in thread-context and use mutex to protect critical
section, too.
Also, this commit removes some useless spin locks.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Verify wcid is not NULL before dereferencing the pointer to initialize
txwi rate/power info
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize mt76_txq pointer after ieee80211_txq pointer check.
Remove space after the pointer cast
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
