We're already using BBP for values > 128. Make that explicit and allow
debugfs access.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch supports Avastar 88W8797 chipset with USB interface.
The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
found in 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO
RT3070:
(0x2019,0x5201) Planex Communications, Inc. RT8070
(0x7392,0x4085) 2L Central Europe BV 8070
7392 is Edimax
RT35xx:
(0x1690,0x0761) Askey
was Fujitsu Stylistic 550, but 1690 is Askey
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7b
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Complete the waiting fwlog_block_read on debugfs cleanup, otherwise
userspace and module unload might softlock.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The original conditions are always true. I think && was intended here,
but I don't have the hardware to test. Could you take a look?
kvalo: Chilam confirmed that the fix is valid
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl: If wow deepsleep pno suspend failure driver will choose cutpower.
in this scenario MMC_PM_KEEP_POWER should be cleared so that mmc will power
off the ar6000
kvalo: remove extra parenthesis
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The iwmc3200 driver selects other code in Kconfig that depends on
EXPERIMENTAL. Kconfig warns about this when CONFIG_EXPERIMENTAL
is not already set, so logically, these options should also
be marked experimental or promoted to stable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so
replace it with a NULL pointer when the section gets discarded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having cmd[], meta[] and skbs[] as separate arrays
in the TX queue structure is cache inefficient as
we need the data for a given entry together.
To improve this, create an array with these three
members (allocate meta as part of that struct) so
we have the data we need together located together
improving cache footprint.
The downside is that we need to allocate a lot of
memory in one chunk, about 10KiB (on 64-bit) which
isn't very efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This allows not to notify the transport about aggregation stopped
while aggregation haven't been started.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.
MVM doesn't have to use this declaration.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using the shared area that we be killed.
Remove the pointer to config from shared since it is not
used any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The driver layer now holds a pointer to the transport,
and shrd->drv is not needed any more, so kill it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.
Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.
In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.
kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.
The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.
Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.
Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
