The current code, since commit bb43d40d7c ("drm/sun4i: rgb: Validate the
clock rate"), perform some validation on the pixel clock to filter out the
EDID modes provided by monitors (through bridges) that we wouldn't be able
to reach. For the usual modes, we're able to generate a perfect clock rate,
so a strict check was enough.
However, this had the side effect of preventing displays that would work
otherwise to operate properly, since we would pretty much never be able to
generate an exact rate for those displays, even though we would fall within
that panel tolerance.
This was also shown to happen for unusual modes exposed through EDIDs, for
example on eDP panels.
We can work around this by simplifying a bit the problem: no panels we've
encountered so far actually needed that check. All of them are tied to a
particular board when it is produced, and made to work with the Allwinner
BSP. That pretty much guarantees that we never have a pixel clock out of
reach.
On the other hand, the EDIDs modes that needed to be validated have always
been exposed through bridges.
Let's just use that metric to instead of validating all modes, only
validate modes when we have a bridge attached. It should be good enough for
now, while we still have room for improvements or refinements using the
display_timings structure for example for panels.
We also add a tolerance for EDID-based modes instead of doing a strict
check. This tolerance is of 0.5% which is the one advertised in the VESA
DVT and CVT specs. If that needed to be extended in the future, we can add
a custom module parameter to relax it a bit.
Fixes: bb43d40d7c ("drm/sun4i: rgb: Validate the clock rate")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # tested on pinebook
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ec2dc2a7b3d4bd44f7a2a6e1c1813f92449a7310.1551191081.git-series.maxime.ripard@bootlin.com
The preferred bpp for the fbdev emulation buffer has been 32 so far, which
means that by default we will allocate an 8MB buffer with a 1920x1080
resolution.
Worse this memory will be allocated from the CMA pool, and will never be
freed even if we don't use the fbdev emulation. Therefore, reducing it is a
big deal, and switching to 16bpp by default will gain us around 4MB at
1920x1080, while keeping decent color depth. And users still have the
option to switch to 32bpp using the kernel command line.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190306140245.21973-1-maxime.ripard@bootlin.com
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
Pull sound updates from Takashi Iwai:
"We had again a busy development cycle with many new drivers as well as
lots of core improvements / cleanups. Let's go for highlights:
ALSA core:
- PCM locking scheme was refactored for reducing a global rwlock
- PCM suspend is handled in the device type PM ops now; lots of
explicit calls were reduced by this action
- Cleanups about PCM buffer preallocation calls
- Kill NULL device object in memory allocations
- Lots of procfs API cleanups
ASoC core:
- Support for only powering up channels that are actively being used
- Cleanups / fixes of topology API
ASoC drivers:
- MediaTek BTCVSD for a Bluetooth radio chip, which is the first such
driver we've had upstream!
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers
- Lots of fixes for probing on Intel systems to follow more standard
styles
- A big refresh and cleanup of the Samsung drivers
- New drivers: Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341
and CS35L26, Google ChromeOS embedded controllers, Ingenic JZ4725B,
MediaTek BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328,
Spreadtrum DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM
formatters
ALSA drivers:
- Improvements of Tegra HD-audio controller driver for supporting new
chips
- HD-audio codec quirks for ALC294 S4 resume, ASUS laptop, Chrome
headset button support and Dell workstations
- Improved DSD support on USB-audio
- Quirk for MOTU MicroBook II USB-audio
- Support for Fireface UCX support and Solid State Logic Duende
Classic/Mini"
* tag 'sound-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (461 commits)
ALSA: usb-audio: Add quirk for MOTU MicroBook II
ASoC: stm32: i2s: skip useless write in slave mode
ASoC: stm32: i2s: fix race condition in irq handler
ASoC: stm32: i2s: remove useless callback
ASoC: stm32: i2s: fix dma configuration
ASoC: stm32: i2s: fix stream count management
ASoC: stm32: i2s: fix 16 bit format support
ASoC: stm32: i2s: fix IRQ clearing
ASoC: qcom: Kconfig: fix dependency for sdm845
ASoC: Intel: Boards: Add Maxim98373 support
ASoC: rsnd: gen: fix SSI9 4/5/6/7 busif related register address
ALSA: firewire-motu: fix construction of PCM frame for capture direction
ALSA: bebob: use more identical mod_alias for Saffire Pro 10 I/O against Liquid Saffire 56
ALSA: hda: Extend i915 component bind timeout
ASoC: wm_adsp: Improve logging messages
ASoC: wm_adsp: Add support for multiple compressed buffers
ASoC: wm_adsp: Refactor compress stream initialisation
ASoC: wm_adsp: Reorder some functions for improved clarity
ASoC: wm_adsp: Factor out stripping padding from ADSP data
ASoC: cs35l36: Fix an IS_ERR() vs NULL checking bug
...
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
Powerplay functions called from dm_pp_* functions tend to do a
mutex_lock which isn't safe to do inside a kernel_fpu_begin/end block as
those will disable/enable preemption.
Rearrange the dm_pp_get_clock_levels_by_type_with_voltage calls to make
sure they happen outside of kernel_fpu_begin/end.
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code clears the DPLL register entirely when re-enabling
VGA mode temporarily during the DPLL enable sequence. On i830 we want to
keep the DPLLs on all the time, so let's not do this temporary
disabling.
The current code does work, so this doesn't seem super important.
But I prefer that we make the behaviour 100% consistent.
v2: Split this change the DVO 2x clocking patch
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190305192400.23121-1-ville.syrjala@linux.intel.com
In order to test whether the load tracker is working as expected, we
need the ability to compare the commit result with the underrun
indication. With the load tracker always enabled, commits that are
expected to trigger an underrun are always rejected, so userspace
cannot get the actual underrun indication from the hardware.
Add a debugfs entry to disable/enable the load tracker, so that a DRM
commit expected to trigger an underrun can go through with the load
tracker disabled. The underrun indication is then available to
userspace and can be checked against the commit result with the load
tracker enabled.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220155124.25022-4-paul.kocialkowski@bootlin.com
The HVS block is supposed to fill the pixelvalve FIFOs fast enough to
meet the requested framerate. The problem is, the HVS and memory bus
bandwidths are limited, and if we don't take these limitations into
account we might end up with HVS underflow errors.
This patch is trying to model the per-plane HVS and memory bus bandwidth
consumption and take a decision at atomic_check() time whether the
estimated load will fit in the HVS and membus budget.
Note that we take an extra margin on the memory bus consumption to let
the system run smoothly when other blocks are doing heavy use of the
memory bus. Same goes for the HVS limit, except the margin is smaller in
this case, since the HVS is not used by external components.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190220155124.25022-3-paul.kocialkowski@bootlin.com
The migration scanner is a linear scan of a zone with a potentiall large
search space. Furthermore, many pageblocks are unusable such as those
filled with reserved pages or partially filled with pages that cannot
migrate. These still get scanned in the common case of allocating a THP
and the cost accumulates.
The patch uses a partial search of the free lists to locate a migration
source candidate that is marked as MOVABLE when allocating a THP. It
prefers picking a block with a larger number of free pages already on
the basis that there are fewer pages to migrate to free the entire
block. The lowest PFN found during searches is tracked as the basis of
the start for the linear search after the first search of the free list
fails. After the search, the free list is shuffled so that the next
search will not encounter the same page. If the search fails then the
subsequent searches will be shorter and the linear scanner is used.
If this search fails, or if the request is for a small or
unmovable/reclaimable allocation then the linear scanner is still used.
It is somewhat pointless to use the list search in those cases. Small
free pages must be used for the search and there is no guarantee that
movable pages are located within that block that are contiguous.
5.0.0-rc1 5.0.0-rc1
noboost-v3r10 findmig-v3r15
Amean fault-both-3 3771.41 ( 0.00%) 3390.40 ( 10.10%)
Amean fault-both-5 5409.05 ( 0.00%) 5082.28 ( 6.04%)
Amean fault-both-7 7040.74 ( 0.00%) 7012.51 ( 0.40%)
Amean fault-both-12 11887.35 ( 0.00%) 11346.63 ( 4.55%)
Amean fault-both-18 16718.19 ( 0.00%) 15324.19 ( 8.34%)
Amean fault-both-24 21157.19 ( 0.00%) 16088.50 * 23.96%*
Amean fault-both-30 21175.92 ( 0.00%) 18723.42 * 11.58%*
Amean fault-both-32 21339.03 ( 0.00%) 18612.01 * 12.78%*
5.0.0-rc1 5.0.0-rc1
noboost-v3r10 findmig-v3r15
Percentage huge-3 86.50 ( 0.00%) 89.83 ( 3.85%)
Percentage huge-5 92.52 ( 0.00%) 91.96 ( -0.61%)
Percentage huge-7 92.44 ( 0.00%) 92.85 ( 0.44%)
Percentage huge-12 92.98 ( 0.00%) 92.74 ( -0.25%)
Percentage huge-18 91.70 ( 0.00%) 91.71 ( 0.02%)
Percentage huge-24 91.59 ( 0.00%) 92.13 ( 0.60%)
Percentage huge-30 90.14 ( 0.00%) 93.79 ( 4.04%)
Percentage huge-32 90.03 ( 0.00%) 91.27 ( 1.37%)
This shows an improvement in allocation latencies with similar
allocation success rates. While not presented, there was a 31%
reduction in migration scanning and a 8% reduction on system CPU usage.
A 2-socket machine showed similar benefits.
[mgorman@techsingularity.net: several fixes]
Link: http://lkml.kernel.org/r/20190204120111.GL9565@techsingularity.net
[vbabka@suse.cz: migrate block that was found-fast, some optimisations]
Link: http://lkml.kernel.org/r/20190118175136.31341-10-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <Vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the BACO functions are common across smu9-based
asics. Split the common code out.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_commit_updates_for_stream is called twice per stream: once
with the flip data and once will all other data. This causes
problems when these DC calls have different numbers of planes
For example, a commit with a pageflip on plane A and a
non-pageflip change on plane B will first call
into DC with just plane A, causing plane B to be
disabled. Then it will call into DC with both planes,
re-enabling plane B
[How]
Merge flip and full into a single bundle
Apart from the single DC call, the logic should not be
changed by this patch
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDP v1.4 allows panels to report link rates other than RBR/HBR/HBR2, that
may be more optimal for the panel's timing. Power can be saved by using
a link rate closer to the required bandwidth of the panel's timing.
[How]
Scan the table of reported link rates from the panel, and select the
minimum link rate that satisfies the bandwidth requirements of the panel's
timing. Include a flag to make the feature optional.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The wait_for_vblank boolean in commit_tail was passed by reference
into each stream commit, and if that commit was an asynchronous
flip, it would disable vblank waits on all subsequent flips.
This made the behaviour depend on crtc order in a non-intuitive way,
although since the asynchronous pageflip flag is only used by the
legacy IOCTLs at the moment it is never an issue
[How]
Find wait_for_vblank before doing any stream commits
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When doing split pipe, if one pipe is pending on flip, the entire
plane's status should be flip pending, otherwise corruption can occur
when OS writes to a surface prematurely.
[HOW]
Clear the flip pending bit before checking pipes, then OR the flip
pending bits from all pipes together to create the flip pending status
of the entire plane.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <Eryk.Brol@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX arbitration occurs between SW and FW components.
When AUX acquire fails, it causes engine->ddc to be NULL,
which leads to an exception when we try to release the AUX
engine.
[How]
When AUX engine acquire fails, it should return from the
function without trying to continue the operation.
The upper level will determine if it wants to retry.
i.e. dce_aux_transfer_with_retries will be used and retry.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot tries to reuse planes that were enabled for the first
commit applied.
In the case where Raven is booting with two monitors connected and the
first commit contains two streams the screen corruption would occur
because the second stream was trying to re-use a tg and plane that
weren't previously enabled.
The state on the first commit looks something like the following:
TG0: enabled=1
TG1: enabled=0
TG2: enabled=0
TG3: enabled=0
New state: pipe=0, stream=0, plane=0, new_tg=0
New state: pipe=1, stream=1, plane=1, new_tg=1
New state: pipe=2, stream=NULL, plane=NULL, new_tg=NULL
New state: pipe=3, stream=NULL, plane=NULL, new_tg=NULL
Only one plane/tg is setup before we enter accelerated mode so
we really want to disabling everything but that first plane.
[How]
Check if the stream is not NULL and if the tg is enabled before
deciding whether to skip the plane disable.
Also ensure we're also disabling on the current state's pipe_ctx so
we don't overwrite the fields in the new pending state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change changes dc add plane logic to allow plane-less resource
reservation (pipe split).
If a free pipe_ctx (no plane_state attached) is the head pipe, and is
found with a bottom pipe attached, assign the plane to add on the bottom
pipe.
In addition, prepend dcn10 to dcn10-specific reset_back_end_for_pipe
and reset_hw_ctx_wrap
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver need to poll the SURFACE_INUSE register to determine when to
start the new task and write data to the checked surface.
Implement the wait functions, and add the necessary hubbub registers.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot code not working on all ASICs because of
some underflow issues caused by some uninitialized HW
state.
[How]
Keep some logical and power gating init code in hw_init.
Move some per pipe init code to enable accelerated mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make dml and integration with pplib clearer.
[How]
Change the way the dml formula is initialized to make its values more
clear. Restructure DC interface with pplib into rv_funcs.
Cap clocks received from pplib.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In VRR mode, keep track of the vblank count of the last
completed pageflip in amdgpu_crtc->last_flip_vblank, as
recorded in the pageflip completion handler after each
completed flip.
Use that count to prevent mmio programming a new pageflip
within the same vblank in which the last pageflip completed,
iow. to throttle pageflips to at most one flip per video
frame, while at the same time allowing to request a flip
not only before start of vblank, but also anywhere within
vblank.
The old logic did the same, and made sense for regular fixed
refresh rate flipping, but in vrr mode it prevents requesting
a flip anywhere inside the possibly huge vblank, thereby
reducing framerate in vrr mode instead of improving it, by
delaying a slightly delayed flip requests up to a maximum
vblank duration + 1 scanout duration. This would limit VRR
usefulness to only help applications with a very high GPU
demand, which can submit the flip request before start of
vblank, but then have to wait long for fences to complete.
With this method a flip can be both requested and - after
fences have completed - executed, ie. it doesn't matter if
the request (amdgpu_dm_do_flip()) gets delayed until deep
into the extended vblank due to cpu execution delays. This
also allows clients which want to regulate framerate within
the vrr range a much more fine-grained control of flip timing,
a feature that might be useful for video playback, and is
very useful for neuroscience/vision research applications.
In regular non-VRR mode, retain the old flip submission
behavior. This to keep flip scheduling for fullscreen X11/GLX
OpenGL clients intact, if they use the GLX_OML_sync_control
extensions glXSwapBufferMscOML(, ..., target_msc,...) function
with a specific target_msc target vblank count.
glXSwapBuffersMscOML() or DRI3/Present PresentPixmap() will
not flip at the proper target_msc for a non-zero target_msc
if VRR mode is active with this patch. They'd often flip one
frame too early. However, this limitation should not matter
much in VRR mode, as scheduling based on vblank counts is
pretty futile/unusable under variable refresh duration
anyway, so no real extra harm is done.
According to some testing already done with this patch by
Nicholas on top of my tests, IGT tests didn't report any
problems. If fixes stuttering and flickering when flipping
at rates below the minimum vrr refresh rate.
Fixes: bb47de7366 ("drm/amdgpu: Set FreeSync state using drm VRR
properties")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel@daenzer.net>
Tested-by: Bruno Filipe <bmilreu@gmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DP 1.4 spec defines the SDP header and SDP contents for
a Picture Parameter Set (PPS) that must be sent in advance
of DSC transmission to define the encoding characteristics.
This was done in one struct, drm_dsc_pps_infoframe, which
conatined the SDP header and PPS. Because the PPS is
a property of DSC over any connector, not just DP, and because
drm drivers may have their own SDP structs they wish to use,
make the functions that initialise SDP and PPS headers take
the components they operate on, not drm_dsc_pps_infoframe,
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221202001.28430-4-David.Francis@amd.com
