The frontend documentation (for the A33) mentions that ARGB is supported
as output, but with the alpha component always set to 0xff. In practice,
this means that the alpha component cannot be preserved when going
through the frontend. Since the information is lost, ARGB is not
properly supported.
As a result, expose the matching format supported by the frontend (both
for input and output) as XRGB instead of ARGB.
Since ARGB was the selected format for connecting the frontend to the
backend, change it to XRGB to reflect this as well.
The A31 and A80 SoCs apparently have a bit to enable proper alpha,
but this is not supported at this point (see the comment already in the
code).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-3-paul.kocialkowski@bootlin.com
This adds a dedicated function for cleaning the video and YUV source
channel layer enable bits. This function is called first on layer atomic
update to make sure that there are no leftover bits from previous
plane configuration that were not cleaned until now.
It fixes issues when alternating between video and YUV planes, where
both bits would be set eventually, leading to broken plane display.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123092515.2511-2-paul.kocialkowski@bootlin.com
Since Linux 4.17, calls to drm_crtc_vblank_on/off are mandatory, and we get
a warning when ctrc is disabled :
" driver forgot to call drm_crtc_vblank_off()"
But, the vsync IRQ was not totally disabled due the transient hardware
state and specific interrupt line, thus adding proper IRQ masking from
the HHI system control registers.
The last change fixes a race condition introduced by calling the added
drm_crtc_vblank_on/off when an HPD event occurs from the HDMI connector,
triggering a WARN_ON() in the _atomic_begin() callback when the CRTC
is disabled, thus also triggering a WARN_ON() in drm_vblank_put() :
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/meson/meson_crtc.c:157 meson_crtc_atomic_begin+0x78/0x80
[...]
Call trace:
meson_crtc_atomic_begin+0x78/0x80
drm_atomic_helper_commit_planes+0x140/0x218
drm_atomic_helper_commit_tail+0x38/0x80
commit_tail+0x7c/0x80
drm_atomic_helper_commit+0xdc/0x150
drm_atomic_commit+0x54/0x60
restore_fbdev_mode_atomic+0x198/0x238
restore_fbdev_mode+0x6c/0x1c0
drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xf0
drm_fb_helper_set_par+0x34/0x60
drm_fb_helper_hotplug_event.part.28+0xb8/0xc8
drm_fbdev_client_hotplug+0xa4/0xe0
drm_client_dev_hotplug+0x90/0xe0
drm_kms_helper_hotplug_event+0x3c/0x48
drm_helper_hpd_irq_event+0x134/0x168
dw_hdmi_top_thread_irq+0x3c/0x50
[...]
WARNING: CPU: 0 PID: 1185 at drivers/gpu/drm/drm_vblank.c:1026 drm_vblank_put+0xb4/0xc8
[...]
Call trace:
drm_vblank_put+0xb4/0xc8
drm_crtc_vblank_put+0x24/0x30
drm_atomic_helper_wait_for_vblanks.part.9+0x130/0x2b8
drm_atomic_helper_commit_tail+0x68/0x80
[...]
The issue is that vblank need to be enabled in any occurrence of :
- atomic_enable()
- atomic_begin() and state->enable == true, which was not the case
Moving the CRTC enable code to a common function and calling in one of
these occurrence solves this race condition and makes sure vblank is
enabled in each call to _atomic_begin() from the HPD event leading to
drm_atomic_helper_commit_planes().
To Summarize :
- Make sure that the CRTC code will call the drm_crtc_vblank_on()/off()
- *Really* mask the Vsync IRQ
- Initialize and enable vblank at the first
atomic_begin()/_atomic_enable()
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[fixed typos+added cc for stable]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122160103.10993-1-narmstrong@baylibre.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Jerry Zuo pointed out a rather obscure hotplugging issue that it seems I
accidentally introduced into DRM two years ago.
Pretend we have a topology like this:
|- DP-1: mst_primary
|- DP-4: active display
|- DP-5: disconnected
|- DP-6: active hub
|- DP-7: active display
|- DP-8: disconnected
|- DP-9: disconnected
If we unplug DP-6, the topology starting at DP-7 will be destroyed but
it's payloads will live on in DP-1's VCPI allocations and thus require
removal. However, this removal currently fails because
drm_dp_update_payload_part1() will (rightly so) try to validate the port
before accessing it, fail then abort. If we keep going, eventually we
run the MST hub out of bandwidth and all new allocations will start to
fail (or in my case; all new displays just start flickering a ton).
We could just teach drm_dp_update_payload_part1() not to drop the port
ref in this case, but then we also need to teach
drm_dp_destroy_payload_step1() to do the same thing, then hope no one
ever adds anything to the that requires a validated port reference in
drm_dp_destroy_connector_work(). Kind of sketchy.
So let's go with a more clever solution: any port that
drm_dp_destroy_connector_work() interacts with is guaranteed to still
exist in memory until we say so. While said port might not be valid we
don't really care: that's the whole reason we're destroying it in the
first place! So, teach drm_dp_get_validated_port_ref() to use the all
mighty current_work() function to avoid attempting to validate ports
from the context of mgr->destroy_connector_work. I can't see any
situation where this wouldn't be safe, and this avoids having to play
whack-a-mole in the future of trying to work around port validation.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 263efde31f ("drm/dp/mst: Get validated port ref in drm_dp_update_payload_part1()")
Reported-by: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: <stable@vger.kernel.org> # v4.6+
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113224613.28809-1-lyude@redhat.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There is a spelling mistake in the module description text and
a comment too, fix them. Also line break overly long comment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ACPI ATIF has a function called query
backlight transfer characteristics. Among the
information returned by this function is
the minimum and maximum input signals for the
backlight
Call that function on ACPI init. When DM
backlight device is updated, copy over the
backlight caps into DM, but only once. Use
the backlight caps in the backlight-to-dc
calculation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ACPI interface in AMD was a few years out of date
and contained some unused and deprecated functions
Remove functions: Select Active Displays, Get Lid State,
Get TV Standard, Set TV Standard, Get Panel Expansion Mode,
Set Panel Expansion Mode, Get Graphics Device Types
Add functions: Query Backlight Transfer Characteristics,
Ready To Undock Notification
Changed functions: Get System Parameters,
Get System BIOS Requests
All changes are right from the standard
ATI ACPI Control Methods V0.44
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adaptive Backlight Management (ABM) is a feature
that reduces backlight level to save power, while
increasing pixel contrast and pixel luminance
to maintain readability and image quality.
ABM will adjust in response to the
pixel luminance of the displayed content.
ABM is made available as a drm property on eDP
monitors called "abm level", which ranges from 0 to 4.
When this property is set to 0, ABM is off. Levels 1
to 4 represent different ranges of backlight reduction.
At higher levels both the backlight reduction and pixel
adjustment will be greater.
ABM requires DMCU firmware, which is currently available for
Raven ASICs only. If the feature does not work, please
ensure your firmware is up to date.
v2:
Fix commit message, only attach property if DMCU loaded
v3:
Store ABM level in crtc state to accommodate dc
v4:
Fix ABM saving on dpms cycle
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU IRAM must be loaded by the driver before DMCU
can function.
Move the IRAM code out of the shadows and into a new file
modules/power/power_helpers.c
The IRAM table contains the backlight curve and ABM parameters
Add this new file to the Makefiles
Call dmcu_load_iram in late init of DM
Move struct dmcu_version from dc.h to dmcu.h to allow
dmcu to be included on its own
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/amdgpu_csa.c:49 amdgpu_allocate_static_csa()
error: uninitialized symbol 'ptr'.
the test if (!bo) doesn't work, as the bo is a pointer to a pointer.
if bo create failed, the *bo will be set to NULL.
so change to test *bo.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We observe black lines (underflow) on display when playing a
4K video with UVD. On Disabling Low memory P state this issue is
not seen.
In this patch ,disabling low memory P state only when video
size >= 4k.
Multiple runs of power measurement shows no impact
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add hwmgr callback "update_nbdpm_pstate".This will use to access
"cz_nbdpm_pstate_enable_disable" function to enable/disable low
memory pstate.
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit dbd8299c32f6f413f6cfe322fe0308f3cfc577e8.
Reason for revert:
This patch sends msg PPSMC_MSG_DisableLowMemoryPstate(0x002e)
in wrong of sequence to SMU which is before PPSMC_MSG_UVDPowerON (0x0008).
This leads to SMU failing to service the request as it is
dependent on UVD to be powered ON, since it accesses UVD
registers.
This msg should ideally be sent only when the UVD is about to decode
a 4k video.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before:
We use drm_match_cea_mode() to get the vic for any mode we
want to set, most of the time vic will be different for the new mode.
DC uses memcmp to check if timing changed, in this case DC will
say timing changed and we endup doing a full modeset.
Current:
Now we check if !RMX_OFF and old_refresh == new_refresh if so
we copy the vic from old timing. In a case where we are currently on
a lower timing and want to change to higher mode, stream->dst will be
different and cause us to do a full modeset, which is what we want.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Group start/stop is controlled by the DRES and DEN bits of DSYSR0 for
the first group and DSYSR2 for the second group. On most DU instances,
this maps to the first CRTC of the group. On M3-N, however, DU2 doesn't
exist, but DSYSR2 does. There is no CRTC object there that maps to the
correct DSYSR register.
Commit 9144adc5e5 ("drm: rcar-du: Cache DSYSR value to ensure known
initial value") switched group start/stop from using group read/write
access to DSYSR to a CRTC-based API to cache the DSYSR value. While
doing so, it introduced a regression on M3-N by accessing DSYSR3 instead
of DSYSR2 to start/stop the second group.
To fix this, access the DSYSR register directly through group read/write
if the SoC is missing the first DU channel of the group. Keep using the
rcar_du_crtc_dsysr_clr_set() function otherwise, to retain the DSYSR
caching feature.
Fixes: 9144adc5e5 ("drm: rcar-du: Cache DSYSR value to ensure known initial value")
Reported-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Currently, we convert the error state into a string every time we read
from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to
window the string and only capture the portion that is being read, but
that means that we must always convert up to the window to find the
start. For a very large error state bordering on EXEC_OBJECT_CAPTURE
abuse, this is noticeable as it degrades to O(N^2)!
As we do not have a convenient hook for sysfs open(), and we would like
to keep the lazy conversion into a string, do the conversion of the
whole string on the first read and keep the string until the error state
is freed.
v2: Don't double advance simple_read_from_buffer
v3: Due to extreme pain of lack of vrealloc, use a scatterlist
v4: Keep the forward iterator loosely cached
v5: Stylistic improvements to reduce patch size
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Testcase: igt/gem_exec_capture/many*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123132325.26541-1-chris@chris-wilson.co.uk
Consider the following scenario:
1. nonblocking enable crtc
2. wait for the event
3. nonblocking disable crtc
On i915 this can lead to a spurious -EBUSY from step 3 on
account of non-enabled planes getting the fake_commit in step 1
and we don't complete the fake_commit-> flip_done until
drm_atomic_helper_commit_hw_done() which can happen a long
time after the flip event was sent out.
This will become somewhat easy to hit on SKL+ once we start
to add all the planes for the crtc to every modeset commit
for the purposes of forcing a watermark register programming
[1].
To make the race a little less pronounced let's complete
fake_commit->flip_done after drm_atomic_helper_wait_for_flip_done().
For the single crtc case this should make the race quite
theoretical, assuming drm_atomic_helper_wait_for_flip_done()
actually has to wait for the real commit flip_done. In case
the real commit flip_done gets completed singificantly before
drm_atomic_helper_wait_for_flip_done(), or we are dealing with
multiple crtcs whose vblanks don't line up nicely the race still
exists.
[1] https://patchwork.freedesktop.org/patch/262670/
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 080de2e5be ("drm/atomic: Check for busy planes/connectors before setting the commit")
Testcase: igt/kms_cursor_legacy/*nonblocking-modeset-vs-cursor-atomic
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122143412.11655-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The hardware requires the HDSR and VDSR registers to be set to 1 or
higher. This translates to a minimum combined horizontal sync and back
porch of 20 pixels and a minimum vertical back porch of 3 lines. Reject
modes that fail those requirements.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The rcar-du driver supports probe deferral for external clocks, but
implements it badly by checking the wrong pointer due to a bad copy and
paste. Fix it.
While at it, reject invalid clocks outright for DU channels that have a
display PLL, as the external clock is mandatory in that case. This
avoids a WARN_ON() at runtime.
Fixes: 1b30dbde85 ("drm: rcar-du: Add support for external pixel clock")
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Add support for the R-Car M3-N (R8A77965) SoC to the LVDS encoder
driver. The encoder appears identical to the M3-W version, we can thus
simply point to the generic Gen3 data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
will still keep the error set even after the reset done in the
irq_preinstall and irq_uninstall hooks.
And enabling in this situation cause the screen to freeze in the
first time that PSR HW tries to activate so lets keep PSR disabled
to avoid any rendering problems.
v5: rebased: using edp_psr_shift()
v4: Moved handling from intel_psr_compute_config() to
intel_psr_init() to avoid hardware access during compute(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
squash
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-5-jose.souza@intel.com
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
While trying to add a chamelium test for short HPD IRQs, I ran into
issues where a hotplug storm would be triggered, but the point at which
it would be reported by the kernel would be after igt actually finished
checking i915_hpd_storm_ctl's status. So, fix this by simply
synchronizing our IRQ work, dig_port_work, and hotplug_work before
printing out the HPD storm status in i915_hpd_storm_ctl_show().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
