For Picasso && AM4 SOCKET board, we use picasso_rlc_am4.bin
For Picasso && FP5 SOCKET board, we use picasso_rlc.bin
Judgment method:
PCO AM4: revision >= 0xC8 && revision <= 0xCF
or revision >= 0xD8 && revision <= 0xDF
otherwise is PCO FP5
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher at amd.com>
Reviewed-by: Huang Rui <ray.huang at amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if the MC firmware supports FFC and tell the SMC so
mclk switching is handled properly.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
According to Dave, once you've started an L2T flush, all L2T accesses
will be blocked until the flush completes. This fixes a consistent
3-4ms stall between the ioctl and running the job, and 3DMMES Taiji
goes from 27fps to 110fps.
v2: Leave a note about why we don't need to wait for completion.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-4-eric@anholt.net
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
Although commit fb6f0b64e4 ("drm/i915: Prevent machine hang from
Broxton's vtd w/a and error capture") applied cleanly after a 24 month
hiatus, the code had moved on with new methods for peeking and fetching
the captured gpu info. Make sure we catch all uses of the stashed error
state and avoid dereferencing the error pointer.
v2: Move error pointer determination into i915_gpu_capture_state
v3: Restore early check to avoid capturing and then throwing away
subsequent GPU error states.
Fixes: fb6f0b64e4 ("drm/i915: Prevent machine hang from Broxton's vtd w/a and error capture")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207110554.19897-1-chris@chris-wilson.co.uk
Currently we face a severe problem on Braswell that manifests as invalid
ppGTT accesses. The code tries to maintain the PDP (page directory
pointers) inside the context in two ways, direct write into the context
and a pipelined LRI update. The direct write into the context is
fundamentally racy as it is unserialised with any access (read or write)
the GPU is doing. By asserting that Braswell is not used with vGPU
(currently an unsupported platform) we can eliminate the dangerous
direct write into the context image and solely use the pipelined update.
However, the LRI of the PDP fouls up the GPU, causing it to freeze and
take out the machine with "forcewake ack timeouts". This seems possible
to workaround by preventing the GPU from sleeping (via means of
disabling the power-state management interface, i.e. forcing each ring
to remain awake) around the update. Equally, it seems an EMIT_INVALIDATE
before the LRI is sufficient to prevent the forcewake errors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108656
References: https://bugs.freedesktop.org/show_bug.cgi?id=108714
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207090213.14352-3-chris@chris-wilson.co.uk
For a lot of use cases we need 64bit sequence numbers. Currently drivers
overload the dma_fence structure to store the additional bits.
Stop doing that and make the sequence number in the dma_fence always
64bit.
For compatibility with hardware which can do only 32bit sequences the
comparisons in __dma_fence_is_later only takes the lower 32bits as significant
when the upper 32bits are all zero.
v2: change the logic in __dma_fence_is_later
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Link: https://patchwork.freedesktop.org/patch/266927/
Recently gvt shadow ctx create ppgtt table and this ppgtt's root
pointer is modified at workload dispatch, then we lose the original
ppgtt's root pointer, this causes the ppgtt destroy function abnormal
as it will release the wrong root table.
This patch save i915 context ppgtt root pointer at shadow
ctx creation and restore it at shadow ctx destruction.
v2: Split save and restore function (Zhenyu)
Fixes:4f15665ccbba("drm/i915: Add ppgtt to GVT GEM context")
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Host print below warning message when creating guest:
"gvt: vgpu(2) Invalid FORCE_NONPRIV write 83a8".
Register 0x83a8 should be in force-to-nonpriv whitelist as required by
guest
v2: update commit message to describe purpose of this patch in detail
(zhenyu wang)
Signed-off-by: Zhao Yan <yan.y.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Final changes to drm-misc-next for v4.21:
UAPI Changes:
Core Changes:
- Add dma_fence_get_stub to dma-buf, and use it in drm/syncobj.
- Add and use DRM_MODESET_LOCK_BEGIN/END helpers.
- Small fixes to drm_atomic_helper_resume(), drm_mode_setcrtc() and
drm_atomic_helper_commit_duplicated_state()
- Fix drm_atomic_state_helper.[c] extraction.
Driver Changes:
- Small fixes to tinydrm, vkms, meson, rcar-du, virtio, vkms,
v3d, and pl111.
- vc4: Allow scaling and YUV formats on cursor planes.
- v3d: Enable use of the Texture Formatting Unit, and fix
prime imports of buffers from other drivers.
- Add support for the AUO G101EVN010 panel.
- sun4i: Enable support for the H6 display engine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: added drm/v3d: fix broken build to the merge commit]
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/321be9d3-ab75-5f92-8193-e5113662edef@linux.intel.com
We can move the remaining RCS workarounds applied to only gen8 to the
engine->wa_list, and then reduce all engine->init_hw callbacks to common
code. The benefit of using the new wa_list is that we verify that the
registers are indeed restored and keep their magic values.
v2: INSTPM_FORCE_ORDERING is already part of gen8_ctx_workarounds, and
as confirmed by the mmio verification is a part of the context image!
v3: MI_MODE is already part of gen8_ctx_workarounds...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206180713.6827-2-chris@chris-wilson.co.uk
If the SOR is already up and running when the kernel driver is probed,
setting a mode will typically fail. This can be seen for example on
Jetson TX2. Under certain circumstances the generic power domain code
will cause the SOR to be reset. However, if the power domain is never
powered off (this can happen if the HDA controller is enabled, which
is part of the same power domain as the SOR), then the SOR will end up
not getting reset and fail to properly set a mode.
To work around this, try to get the reset control and assert/deassert
it, irrespective of whether or not a generic power domain is attached
to the SOR. On platforms where the kernel implements generic power
domains (up to Tegra210) this will fail, because the power domain will
already have acquired an exclusive reference to the reset control. But
on recent platforms there the BPMP provides an ABI to control power
domains, it's possible to acquire the reset control from SOR and use
it to put the SOR into a known good state at probe time.
The proper solution for this is to make the SOR driver capable of
dealing with hardware that's already up and running (by first grace-
fully shutting it down, or perhaps by seamlessly transitioning to the
kernel driver and taking over the running display configuration). That
is fairly involved, though, so we'll go with this quickfix for now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the temporary workaround of storing the Tegra186 HDMI/DP I/O pad
ID in the SOR driver. The definition has long been available in the
soc/tegra/pmc.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
At enable/disable of the HDCP encryption, for encryption status change
we need minimum one frame duration. And we might program this bit any
point(start/End) in the previous frame.
With 20mSec, observed the timeout for change in encryption status.
Since this is not time critical operation and we need to hold on
until the status is changed, fixing the timeout to 50mSec. (Based on
trial and error method!)
v2:
%s/TIME_FOR_ENCRYPT_STATUS_CHANGE/ENCRYPT_STATUS_CHANGE_TIMEOUT_MS
[Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544010283-20223-5-git-send-email-ramalingam.c@intel.com
- Refactoring of DMA and IOMMU code
. This patch series simplifies DMA mapping creation by avoiding looping
all components to get dma device object, reduces code size by merging
IOMMU and DMA code.
- Enhance plane alpha and blend mode support
. This patch series adds configurable plane and pixel blend mode support
for Exynos5433 DECON device.
- Fix color format setting of Mixer driver
. This patch series fixes color format and range setting by splitting
range and format.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1544002853-11661-1-git-send-email-inki.dae@samsung.com
amdgpu and amdkfd:
- Freesync support
- ABM support in DC
- KFD support for vega12 and polaris12
- Add sdma paging queue support for vega
- Use ACPI to query backlight range on supported platforms
- Clean up doorbell handling
- KFD fix for pasid handling under non-HWS
- Misc cleanups and fixes
scheduler:
- Revert "fix timeout handling v2"
radeon:
- Fix possible overflow on 32 bit
ttm:
- Fix for LRU handling for ghost objects
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130192505.2946-1-alexander.deucher@amd.com
According to DP spec (2.9.3.1 of DP 1.4) if
EXTENDED_RECEIVER_CAPABILITY_FIELD_PRESENT is set the addresses in DPCD
02200h through 0220Fh shall contain the DPRX's true capability. These
values will match 00000h through 0000Fh, except for DPCD_REV,
MAX_LINK_RATE, DOWN_STREAM_PORT_PRESENT.
Read from DPCD once for all 3 values as this is an expensive operation.
Spec mentions that all of address space 02200h through 0220Fh should
contain the right information however currently only 3 values can
differ.
There is no address space in the intel_dp->dpcd struct for addresses
02200h through 0220Fh, and since so much of the data is a identical,
simply overwrite the values stored in 00000h through 0000Fh with the
values that can be overwritten from addresses 02200h through 0220Fh.
This patch helps with backward compatibility for devices pre DP1.3.
v2: read only dpcd values which can be affected, remove incorrect check,
split into drm include changes into separate patch, commit message,
verbose debugging statements during overwrite.
v3: white space fixes
v4: make path dependent on DPCD revision > 1.2
v5: split into function, removed DPCD rev check
v6: add debugging prints for early exit conditions
v7 (From Manasi):
* Memcpy, memcmp and debig logging based on sizeof(dpcd_ext) (Jani N)
* Exit early (Jani N)
v8 (From Manasi):
* Get rid of superfluous debug prints (Jani N)
* Print entire base DPCD before memcpy (Jani N)
v9 (From Manasi):
* Add uniform newlines (Rodrigo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129220058.19636-1-manasi.d.navare@intel.com
This patch adds two new functions to help client drivers suspend and
resume the scheduler job timeout. This can be useful in cases where the
hardware has preemption support enabled. Using this, it is possible to have
the timeout active only for the ring which is active on the ringbuffer.
This patch also makes the job_list_lock IRQ safe.
Suggested-by: Christian Koenig <Christian.Koenig@amd.com>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In cases where the scheduler instance is used as a base object of another
driver object, it's not clear if the driver can call scheduler cleanup on the
fail path. So, Set the sched->thread to NULL, so that the driver can safely
call drm_sched_fini() during cleanup.
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In particular, we need the mmMC_VM_XGMI_LFB_CNTL register, for
determining if xGMI is enabled on VG20. This will be used by DC to
determine the correct spread spectrum adjustment for display and audio
clocks.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
