sclk_g3d clock doesn't have enable/disable bits, but the driver hijacked
g3d gate clock bits for this purpose and didn't provide real g3d clock
at all. This patch fixes this issue by adding proper definition for g3d
clock and removing incorrect access to GATE_IP_G3D register in sclk_g3d.
In addition CLK_SET_RATE_PARENT flag is dropped from sclk_g3d, because
it does not make any sense and most likely has been added by mistake.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[tomasz.figa@gmail.com: Adjusted commit message.]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds support for exporting mout_hdmi and mout_mixer to device
tree. Access to those clocks is required to correctly setup HDMI module
on Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Mike Turquette <mturquette@linaro.org>
CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds missing smmu_g2d clock implementation and updates
comment about Exynos4 clocks from 278-282 range. Those clocks are
available on all Exynos4 SoC series, so the misleading comment has been
removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Add clock provider for clocks in DMC domain including EPLL and BPLL. The
DMC clocks are necessary for Exynos3 devfreq driver.
The DMC clock domain uses different address space (0x105C0000) than
standard clock domain (0x10030000 - 0x10050000). The difference is huge
enough to add new DT node for the clock provider, rather than extending
existing address space.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
As per user manual of Exynos3250 SRC_CAM can select
div_cam_blk_320 if it's value is 0xC, so placing
div_cam_blk_320 at proper index in parent list of mout_cam_blk.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Don't abort clock initialization if we cannot match an entry in
tegra_clk_init_table to a valid entry in the clk array.
Also log a corresponding error message.
This was discovered when testing a patch that removed the EMC clock from
tegra124_clks but left a mention in tegra_clk_init_table.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Commit 15917b1602 ("clk: mvebu: Fix clk
frequency value if SSCG is enabled") introduced some logic in the
common mvebu clock code to adjust the clock frequency according to the
configuration of the SSCG.
In order to do this, it looks up for a DT node called "sscg" and maps
it before accessing the SSCG configuration register.
However, the lookup is currently done using:
sscg_np = of_find_node_by_name(np, "sscg");
where "np" is a pointer to the DT node of the clock for which we are
calculating the adjusted frequency. This means that if the "sscg" node
is *after* the clock node in the Device Tree, it works fine (and
that's the case for Armada 370).
However, if it turns out that the "sscg" node is *before* the clock
node in the Device Tree, it won't work because the sscg node will not
be found.
What we really want here is a search of the entire Device Tree, not
only starting from the clock node, so instead of passing "np" as first
argument of of_find_node_by_name(), we simply need to pass
NULL. Passing a non-NULL argument is typically used in a loop, so that
the search for the next matching node starts right after the node that
was matched.
This makes the "np" argument to the kirkwood_fix_sscg_deviation()
function unnecessary, which leads to further cleanups.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 15917b1602 ("clk: mvebu: Fix clk frequency value if SSCG is enabled")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1410880503-2322-1-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The sun4i-apb0 clock, as found on all platforms using it, is a
power-of-two-based divider clock, with a special divider of 2
for value 0.
This was causing the clock framework to incorrectly calculate
the clock rate for apb1 and related modules on sun6i and sun8i.
On sun[4/5/7]i, u-boot SPL configures the divider with value 1
for /2 divider, so no suprises there.
This patch adds a proper divider table for it, so the correct
clock rate can be calculated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwc2 usb controller also uses agressive clock gating, which in this
case leads to hclk_peri getting disabled and hanging the system.
Therefore move it to the critical clocks until we also control that
part of the system.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
On 32bit architectures, like ARM calculating the fractional rate will
do the multiplication before converting the value to u64 when it gets
assigned to ret, which can produce overflows.
The error in question happened with a parent_rate of 386MHz, m = 3000,
n = 60000, which resulted in a wrong rate value of 15812Hz.
Therefore cast parent_rate to u64 to make sure the multiplication
happens in a 64bit space and produces the correct 192MHz in the example.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The MAX77802 PMIC has two 32.768kHz Buffered Clock Outputs with
Low Jitter Mode. This patch adds support for these two clocks.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Clocks drivers for Maxim PMIC are very similar so they can
be converted to use the generic Maxim clock driver.
Also, while being there use module_platform_driver() helper
macro to eliminate more boilerplate code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Maxim Integrated Power Management ICs are very similar with
regard to their clock outputs. Most of the clock drivers for
these chips are duplicating code and are simpler enough that
can be converted to use a generic driver to consolidate code
and avoid duplication.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a dt-binding include for Maxim 77686
PMIC clock IDs that can be used by both the max77686
clock driver and Device Tree source files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Since commit 54196ccbe0 (of: consolidate linker section OF match table
declarations) which went into 3.16-rc1 the following compiler warning is
generated:
In file included from drivers/clk/clk-efm32gg.c:12:0: include/linux/of.h:772:20:
warning: comparison of distinct pointer types lacks a cast [enabled by default]
.data = (fn == (fn_type)NULL) ? fn : fn }
^
include/linux/of.h:785:3: note: in expansion of macro '_OF_DECLARE'
_OF_DECLARE(table, name, compat, fn, of_init_fn_1)
^
include/linux/clk-provider.h:545:42: note: in expansion of macro 'OF_DECLARE_1'
#define CLK_OF_DECLARE(name, compat, fn) OF_DECLARE_1(clk, name, compat, fn)
^
drivers/clk/clk-efm32gg.c:81:1: note: in expansion of macro 'CLK_OF_DECLARE'
CLK_OF_DECLARE(efm32ggcmu, "efm32gg,cmu", efm32gg_cmu_init);
^
Fix it by making efm32gg_cmu_init return void.
Cc: Rob Herring <robh@kernel.org>
Reported-by: Bryan Hundven <bryanhundven@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
As checkpatch suggests:
WARNING: Possible unnecessary 'out of memory' message,
remove an error message after failing kmalloc() from the PLL driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When the SSCG (Spread Spectrum Clock Generator) is enabled, it shifts
the frequency of the clock. The percentage is no more than 1% but when
the clock is used for a timer it leads to a clock drift.
This patch allows to correct the affected clock when the SSCG is
enabled. The check is done in an new optional function related to each
SoC: is_sscg_enabled(). The fix is done with the other new optional
function related to each SoC: fix_sscg_deviation. If one these
functions are not present then no correction is done on the clock
frequency.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Link: https://lkml.kernel.org/r/1409645719-20003-2-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In some cases, clocks can switch their parent with clk_set_rate, for
example clk_mux can do this in some cases. Current implementation of
clk_change_rate uses un-safe list iteration on the clock children, which
will cause wrong clocks to be parsed in case any of the clock children
change their parents during the change rate operation. Fixed by using
the safe list iterator instead.
The problem was detected due to some divide by zero errors generated
by clock init on dra7-evm board, see discussion under
http://article.gmane.org/gmane.linux.ports.arm.kernel/349180 for details.
Fixes: 71472c0c06 ("clk: add support for clock reparent on set_rate")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clocks for i2c1 and i2c2 are flipped. The clock tree matched the
Technical Reference Manual (TRM) but the TRM was wrong. Swap them in
the clock tree. This was determined experimentally (by Addy) and
confirmed by the Rockchip IC team.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The pre-divider for the sdc clocks only has 2 bits in it, so we
can't possibly divide by anything larger than 4 here.
Furthermore, we program the value of ~(n - m) and the n value is
larger than 8 bits (max of 256). Replace this entry with 200kHz
which is close enough to 144kHz to be usable.
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Fixes: 24d8fba44a "clk: qcom: Add support for IPQ8064's global clock controller (GCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The RM9200 USB clock is actually connected to a single parent (the PLLB)
on which we can apply a specific divider.
The USB clock divider does not allow for fine grained control on the USB
clock frequency, hence propagating the set_rate request to the parent is
the only choice we have to properly configure the USB clock rate.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Use the cached values to calculate PLL rate instead of the register values.
This is required to prevent erroneous PLL rate return when the PLL rate
has been configured but the PLL is not prepared yet.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The AT91 PLL rate configuration is done by configuring a multiplier/divider
pair.
The previous calculation was over-complicated (and apparently buggy).
Simplify the implementation and add some comments to explain what is done
here.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Gaël PORTAY <gael.portay@gmail.com>
Tested-by: Gaël PORTAY <gael.portay@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock-tree contains clocks that should never get disabled automatically.
One example are the base ACLKs, the base supplies for all peripherals.
Therefore add a structure similar to the sunxi clock-tree to protect these
special clocks from being disabled.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is only used locally in clk/rockchip/clk.c and thus can be static.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rockchip SoCs may provide fraction dividers for some clocks, mostly for
i2s and uarts. In contrast to the other registers, these do not use
the hiword-mask paradigm, but instead split the register into the upper
16 bit for the nominator and the lower 16 bit for the denominator.
The common clock framework got a generic fractional divider clock type
recently that can accomodate this setting easily. All currently known
fraction dividers have a separate gate too, therefore implement the
divider as composite using the ops-struct from fractional_divider clock
and add the gate if necessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The powersave clock acts like a multiplexer for the cpu, selecting
either the clock signal derived from the cpu pll or from the ddr clock.
This patch changes powersave from a gate clock to a mux clock to better
reflect this behavior.
This is a cleaner approach whereby the frequency of the cpu always
matches the rate of powersave_clk. The cpufreq driver for the kirkwood
platform no longer must parse this behavior out of various calls to
clk_enable and clk_disable, but can instead simply select the parent cpu
it wants when changing rate. Likewise when requesting the cpu rate we
need only query powersave_clk's rate through the usual call to
clk_get_rate.
The new clock data and corresponding changes to the cpufreq driver are
combined into this single commit to avoid a git bisect issue where this
cpufreq driver fails to work properly between the commit that updates
the kirkwood clock driver and the commit that changes how the cpufreq
driver uses that clock.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Kirkwood is unique among the mvebu SoCs for having a clock multiplexer
that feeds into the cpu. This multiplexer can select either the cpu pll
or the ddr clock as its input signal, allowing for a choice between
performance and power savings.
This patch introduces the code needed to register the clock multiplexer
on Kirkwood SoCs but does not include the clock data to actually
register the clock. That will be done in a follow-up patch which is
necessary to prevent breaking git bisect.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Refactor mvebu_clk_gating_setup() to use a common spinlock instead of a
unique lock for every instance of a struct clk_gating_ctrl object. This
will be used later for a separate mux clock type that shares a register
with gate clock types and needs to use the same lock to protect access
to the register.
Cc: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull AT91 reset, poweroff and ram drivers from Maxime Ripard:
"This tag holds the various new drivers introduced to move code that used to be
in mach-at91 over to the proper frameworks.
These files are the reboot and poweroff code for all AT91 SoCs but the RM9200,
and the ram controller driver is not doing much at the time, except for grabing
the RAM clock in order to leave it always enabled."
Conflicts:
arch/arm/mach-at91/Kconfig
Check for valid parameters in check rate. Else, we end up getting
errors.
This occurs as part of the inital clock tree update of child clock
nodes where new_rate could be 0 for non functional clocks.
Fixes: 9ac33b0ce8 (" CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Check for valid parameters in check rate. Else, we end up getting errors
like:
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0-rc1 #1
[ 0.000000] [<c0015160>] (unwind_backtrace) from [<c0011978>] (show_stack+0x10/0x14)
[ 0.000000] [<c0011978>] (show_stack) from [<c055f5f4>] (dump_stack+0x78/0x94)
[ 0.000000] [<c055f5f4>] (dump_stack) from [<c02e17cc>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02e17cc>] (Ldiv0) from [<c047d228>] (ti_clk_divider_set_rate+0x14/0x14c)
[ 0.000000] [<c047d228>] (ti_clk_divider_set_rate) from [<c047a938>] (clk_change_rate+0x138/0x180)
[ 0.000000] [<c047a938>] (clk_change_rate) from [<c047a908>] (clk_change_rate+0x108/0x180)
This occurs as part of the inital clock tree update of child clock nodes
where new_rate could be 0 for non functional clocks.
Fixes: b4761198bf ("CLK: ti: add support for ti divider-clock")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
